KT-LCD8H E-Bike Display User Manual
ear customer, plese ead thie manual before you ie
{cO8DSpay. Th manual wl guid yu use the strum
corectyto achiev vay of hk
Functions and Display
Instruments using the structure form of instrument body portion and the operation buttons are
conte ae vehi stats displays
designed separately.
1 UP Button Backlight and headlights
2) sweutton || “Environment temperature
3) | powneutton Environment feheenhet |
) wroeY ) ones aby are specter
‘Average speed
6 pst | f
7 eoraey ee | Coo | oslararer
s[ ta | —_teteyveoe |], 7] sreeine
1. Operation
Loner
Hold IMDM button tong to turn on the power, and hold KB tong fora second time to turn off
‘the power. When the motor stops driving and when the e-bike is not used for a consecutive 5
minutes, it will automaticaly shut down and turn off the motor power supply
2. display
Hold OB button to start up and enter display
2.1 Turn on backlit and headlights
Hola LM tong to turn on backlight and headlights (the controller
should have headlight tive output function); hold ES. tong agin to turn
of the backlight and headlights
2.2 Assist ratio gear (ASSIST switch
Press EY or K- to switch 15 fle gear Gear is for the
‘minimum power, gear is for the highest power. Each startup
will automaticaly restore the gear shutdown last time (the
ser can set rancomly). Gear 0s without booster function,
2.3. kmy/H assist promotion function
Hols BA ana A tiasnes, the vehicle deves a the soced
rot more than 6km /h. Release Rl button, the function is
inva.
24 Display and delete of single data
‘After power on for S seconds, hold EM and KA at the
a " same time, single trio ring time (TM) and single trip distance
1.0.0
(057 flash, hold HO button shorty, the content of both is
cleared. If falled holding the button within § seconds, wil
fnutomaticaly return the display Interface afer 5 second,
original content is preserved.
3.Display 2
Press IN button in display to enter display 2
Inthe riding mode after seconds, display 2 automatially
returns to eisplay 3, and the orignal motor power (MOTOR W}
lisplays replaced with motor operating temperature csplay
(MOTOR ‘C) display (the internal motor should be equipped
withthe temperature sensor and the output of temperature detection signal).
Display 3
Press IM button in dsclay2 to enter splay 3.
In the rising condition five seconds later, a single maximum
speed (MS) display automaticaly returns to the real riding
speed (km.
5. Indisplay 3, hold KDW button shortiy(SW),and the
splay will enter display 1
6, Hold IMDM button to turn off the display and the power supply of controller.
7.automaticelly prompt interface7.4 Error Code Display
1. Motor position sensor faut!
2.THROTTLE fault
3.Motor or controller short circuit fault!
Electron conteal system fllure wil spay ashing) faut code, Once the faut
\was removed, it automatically ets from the faut code display interface.
7.2. Motor temperature alarm When the mptor temperature the ftermal motor should be
‘equipped uith the temperature sensorjand the output of temperature detection signal) sever
the warning value, MOTOR °C ("F] ashes to alarm at any display, meanwhile the motor
controller willofer the appropriate protection to mater:
General Project Setting |
4, Set maximum riding speed
‘within s seconds ater power on, hold EM and RA stche
same time to enter Genaral Settngntertace, the ists
maximum speed setting, press MIE button maximum ricing
epoud tach, procs ES or Kl toot tho manimum riding
speed|dfolt 254mf), Pres BI burton Maximum ire
speed stop flashing, then press to enter the next
porarber songs.
2. Wheel diameter setting,
Set whee! diameter ater Maximum speed settings
finished, press. button whet diameter lashes. press EM
cor KA toset the specications of wheel diameter. Select the
range 6,8 1012,14,16 18,20,22,24,26,700¢,28and 29 inches
Press MEDM button whell diameter stop falshing, then press
BD 10 g00 the next parameter settings
3. Setthe metric units
Sel metric units after finishing wheel diameter setting,
press unr ash. press LM or RA to select the thee
‘metriunits of speed, mileage, and ambient temperature i
synchronization. |
‘Mileage
temperature |
4. UNTstop fash after metrie unit setting is completed, Holding MIDM| button again to exit fro
‘setting environment of routine projects and save the setting values, returning to display 1
5. Edt from routine project setting
All three routine project settings can exit from the setting environment and return to the
display by holding MOE button tong after each setting is completed, meanwhile the setting values
are saved,
Under each setting interface, ifthe button failed holding for more than 1 minute, it will
automatically return to display 2, and the setting value is invalid.
Outline Drawings and Dimensions
1, Dimensions of main intrument kody
20.4,
a
pi stiopb sates
1 Pei eter
a
I ww
:
4. Wing dlogram
2, Mounting eimensions of cule brackets
3. Dimensions of button box