JACOBS _
1OCL-Dumad GENERAL SPECIFICATION FOR Page 47 of 49
44AC9100 PRESSURE VESSELS
Doc.no.: 44AC9100-000/V.02/0100/84
Date: 01-Nov-2018
TABLE: 3
MATERIAL SELECTION CHART
‘The following table gives general guidelines for material selection chart for various pressure parts / non
pressure parts of the equipment:
Design] Plate | Pipe (See | Forging Bots ‘Structural Intemal | Studs/
Temp. °C note 8) Studs! attachment — | pipes | Botts /
Nuts walded to Nuss
Excernal | pressure parts Iniomal
CRYOGENIC
From 254] SA240 | SASI2 | SATA2,Gr.F | SAI20, Gr. B8, 80, BT stan
upto-195 | Grso4t, | Type 304 | 304, 3041 916, | hardened
304, 316, | s04L, 316, | 347, 316L SA 194 Gr, 8C, 8T
3161, 347 | 3161. 347
(impact
testec)
Samo as pressure parts
‘Above | SA240 ‘SAIG2 Gr. Fa04 | SARZO, Gr. BE, 8C, eT strain
195 upto | Grs04i, Fs0al. F316 | hardened
80 304, 316, | 304L, 316, ‘SA194.Gr8, 80, 8T
3161, 321, 3161, 321
347 347,
sasz2
sass, | sassa,
553, GrA | Gr8
Low TEMPERATURE
‘Above 80 | SAZ03Gr.| SAsG3 | SA50 SAw@OL? | SA20SGLE | SAK | SA199Gr BB
Upte-60 | Eimpact | Grs.4 | Gr LFS SA 194 Grs.4 | sais4 cre.
tested Grd or Gr?
(see note-
i
‘Above 60 | SAG? | SAGGG | SASGOGrLFS | SAGZOL? | SASA7GIa | SAasa_| SAISa, Gr. BB,
Upte-45 | cit Gs) SAI9¢ Gr4 Gra | saiseara
impact OrGR7
tested
(see note-
i
‘Above 5 | SAST6 (All SAGGa | SAZGOGrLF2 | SAgZOGr. | SASTE(mal | SAasa | SAISa, Gr. 88,
upto-29 | grades) | Gr.6 or L7SAt94 | grades) G61 | Saio4 Gre
impact | Get GrAorGr7
tested
(oe note-
4)
‘Above -29 | SAB16 all] SA106, Gr. | SAi105/Saz66 | SATS ‘SABIE (inal | SA106, | SA-193, Gr. Be,
upto 0 | grades) | B(see | (seenotes) | GrB7 grades) GB | SA194,Gr8.
(Gee note | noie 3) SAI94
3) Gr2kJACOBS
1OCL-Dumad GENERAL SPECIFICATION FOR
PRESSURE VESSELS
Doc.no.: 44AC9100-000/V.02/0100184
44409100
Page 48 of 49
Date: 01-Nov-2018
S21
Design| Plate Pipe _ (See | Forging Baits ‘Structural Internal ‘Studs?
Temp. note 8) ‘Studs / attachment Pies Bots /
&c Nuts walded to Nuss
Extemal__| pressure parts Internal
INTERMEDIATE TEMPERATURE
‘Above 0] SASIG | SATO6GrB | SAIO5 ‘SA103 87 | 152062 (Plates) | SATOSGr.B | SATS
Upto | (all grades) A266 SA194 Gr2H Gre
343 SA194.Gr.
sais387 | Sameas sameas | 4
sazio | sast2 | Sateze | SA194Gr2H | Pressureparts | Pressure
type soat, | TPsoal, — | goat, s16L, parts A193,
Stel, 321 | 3t6L, 321, | s2t Gr,
(soonote | A376 SAto4
4) e321 Gra
‘Roove | SAS87__ | SA395, Gr_| SATB? ‘SA193 GrB7_| Same as Sameas | SAI99
343 | Get clay| PIT Gert SA194¢Gr4 | Pressureparis | Pressure | Gr.88
upto | ci. parts SAIo4
427 ‘SA-193, B7 Gra
sazio | saat2type | ster | SAr94Gr4 | Same as.
type oat, | So4L, si6L, | soat, 316. Pressure parts | Same as
Stel, 321 | 321,8a | sat Pressure | SA193
(soenote | 378 Type parts Gre
4) 32t SA-194
Gre
ELEVATED TEMPERATURE
‘Above | SASS7__] SASS5PTI | SATE2 ‘SAI93Gr.__| Sameas ‘Sameas | SATOSGr
az7up | Gett, lar | $A395 P12 | GeFIT BieSAis4 | Pressure parts | Pressure | B. SA194
rosse | ol, SAIe2 Gra parts Gre
A387 GeFi2
Gri2, O11
cz’
Roave | S240 | SASI2, [SATE __] SATSD Same as Sameas | SATSNGr
427 | type 304, | SAa7étype | 304, 316,921 | Gr. B16 Pressure parts | Pressure | Be. SA194
upto | 316,321, | 304,316, SA194 Gr parts Gre
500 | (Seenoie | 321
4)
‘Above | SAS87___| SASS P22 | SATE ‘SATS Gr. BS,
538 | Gr220.1/ GrF22, A194 Gr3
upto | C12 SAgB7 'SA336 ‘Same as pressure parts
593 | Gr2i.cLar GrF22
cz
‘eave | SA240, | SASI27__[ SATE2Gr.__| SATO, Gr. Ba
500 | Grsosi, | Sas76 | S0aH, at6H, | Sates, are
upto | 16H, Type soan, | 32iH, (strain Samo as pressure parts
as | s2iH 36H, hardened)
{44NC9100-000-V.02.0100-A4 RevJACOBS eS
1OCL-Dumad GENERAL SPECIFICATION FOR Page 49 of 49
44AC3100 PRESSURE VESSELS
Doc.no.: 44AC9100-000/V.02/0100184 Date: 01-Nov-2018
NOTES
10,
"
Pressure vessel steel plates are purchased to the requirement of the standard ASME SA-20
which requires testing of individual plates for low temperature service, Carbon steel material is
ordered to meet the impact requirements of supplement SS, of standard ASME SA 20. Typical
material specification is as follows. SA516 Gr.60 normalised to meet impact requirements per
supplement S5 of SA 20 AT -50 °F.
All permanent attachments welded directly to 9% nickel steel should be of the same material or
of an austentic stainless steel type which can not be hardened by heat treatment.
Check for impact testing requirement as per UCS-66 for coincident temperature and part
thickness,
Selection of stainless steel material shall be based on process recommendation / process
licensor.
This table is not applicable for atmospheric / low pressure storage tanks. Materials shall be
selected as per API 650 / API 620 as applicable.
Materials for caustic service, sour service, or sour service + HIC shall be selected based on
specific recommendation of process licensor & considering chemical composition, hardness,
Vacuum degassing requirements & heat treatment requirements,
Material for pressure vessels designed according to ASME SEC VIII DIV. 2 shall be given special
consideration as per code.
All pipes shall be of seamless construction.
Non-ferrous material and super alloys are not covered above and shall be selected based on
specific recommendation.
Material for vessel / column skirt shall be the same material as of vessel / column shell for upper
part with a minimum of 100mm,
Materials used for IBR equipment shall meet all requirements of Indian Boiler Regulations.