Professional Documents
Culture Documents
ENGLISH
PROJECTOR OPERATION MANUAL
PROJECTEUR MODE D’EMPLOI
PROYECTOR MANUAL DE MANEJO
FRANÇAIS
DT-100
ESPAÑOL
SHARP CORPORATION
Printed in China
Imprimé en China
Impreso en China
TINS-B999WJZZ
05P08-CH-NG
ENGLISH
Introduction
IMPORTANT
• For your assistance in reporting the loss
or theft of your Projector, please record Model No.: DT-100
the Serial Number located on the bottom
of the projector and retain this information.
• Before recycling the packaging, please
Serial No.:
ensure that you have checked the con-
tents of the carton thoroughly against the
list of “Supplied accessories” on page 10.
There are two important reasons for prompt warranty registration of your new SHARP
Projector, using the REGISTRATION CARD packed with the projector.
1. WARRANTY
This is to assure that you immediately receive the full benefit of the parts, service
and labor warranty applicable to your purchase.
2. CONSUMER PRODUCT SAFETY ACT
To ensure that you will promptly receive any safety notification of inspection,
modification, or recall that SHARP may be required to give under the 1972
Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT
“LIMITED WARRANTY” CLAUSE. U.S.A. ONLY
WARNING: High brightness light source. Do not stare into the beam of light, or view
directly. Be especially careful that children do not stare directly into the
beam of light.
INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the operation manual, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help. U.S.A. ONLY
Declaration of conformity
SHARP PROJECTOR, MODEL DT-100
This device complies with Part 15 of the FCC rules. Operation is subject to the following
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Responsible Party:
PRODUCT DISPOSAL
This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of
mercury. Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or, if you are
located in the United States of America, the Electronic Industries Alliance: www.eiae.org .
This SHARP projector uses a DMD panel. This very sophisticated panel contains 409,920 pixels
(micromirrors). As with any high technology electronic equipment such as large screen TVs,
video systems and video cameras, there are certain acceptable tolerances that the equipment
must conform to.
This unit has some inactive pixels within acceptable tolerances which may result in inactive dots
on the picture screen. This will not affect the picture quality or the life expectancy of the unit.
Introduction
■ The specifications are slightly different, depending on the model. However, you can connect and
operate all models in the same manner.
• In this operation manual, the illustration and the screen display are simplified for explanation, and
may differ slightly from the actual display.
ENTER button
MENU/HELP button
Adjustment buttons
(P/R/O/Q)
MENU/HELP
button
ENTER button
Buttons used in
RETURN button
this operation
• Press l RETURN to
return to the previous
screen when the menu
is displayed.
to adjust. Contrast 0
Features
Bright 0
Useful
Color 0
Tint 0
Sharp
CLR Temp
0
7500K
On-screen
Bright Boost 1
Progressive
Lamp Setting
3D Progressive
Bright
display
Reset
SEL./ADJ. ENTER END
39
Using
Basic Operation
Adjusting the Image ............................. 42
Turning the Projector On/Off .............. 28 Adjusting the Color Temperature ......... 42
Connecting the Power Cord ................ 28
Progressive ........................................... 42
Turning the Projector on ....................... 28 Lamp Setting ........................................ 42
Turning the Power off (Putting the
Projector into Standby Mode) ........... 29
Adjusting the Projected Image
Locking the Operation Buttons on the (“SCR - ADJ” menu) ......................... 43
Projector (Keylock Function) ............. 29 Setting the Resize Mode ...................... 43
Image Projection ................................. 30 Keystone Correction ............................ 43
Switching the Input Mode .................... 30 Setting On-screen Display ................... 43
Adjusting the Projected Image ............ 30 Selecting the Background Image ........ 43
Adjusting the Volume ........................... 32 Reversing/Inverting Projected
Displaying the Black Screen and Turning Images ............................................... 43
off the Sound Temporarily ................. 32 Selecting the On-screen Display
Language ........................................... 43
Correcting Trapezoidal Distortion ........ 33
Resize Mode ......................................... 34 Adjusting the Projector Function
(“PRJ - ADJ” menu) .......................... 44
Auto Search Function ........................... 44
Useful Features Auto Sync (Auto Sync Adjustment) ..... 44
Auto Power Off Function ...................... 45
Operating with the Remote Control .... 36 Setting the Confirmation Sound
Freezing a Moving Image .................... 36 (System Sound) ................................. 45
Selecting the Picture Mode .................. 36 Speaker Setting .................................... 45
Auto Sync (Auto Sync Adjustment) ..... 36 Fan Mode Setting ................................. 45
Menu Items ......................................... 37 Checking the Lamp Life Status ........... 45
Using the Menu Screen ...................... 39 Troubleshooting with “Help” menu ...... 46
Menu Selections (Adjustments) ........... 39 Utilizing “Help” menu functions ........... 46
Picture Adjustment (“Picture” menu) .. 41
Selecting the Picture Mode .................. 41
• DLP\ (Digital Light Processing) and DMD\ (Digital Micromirror Device) are trademarks
of Texas Instruments, Inc.
• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United
States and/or other countries.
• PC/AT is a registered trademark of International Business Machines Corporation in the
United States.
• Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or
other countries.
• All other company or product names are trademarks or registered trademarks of their
respective companies.
• Some IC chips in this product include confidential and/or trade secret property belonging
to Texas Instruments. Therefore you may not copy, modify, adapt, translate, distribute,
reverse engineer, reverse assemble or discompile the contents thereof.
Do not set up the projector in places ex- Avoid locations with extremes of tem-
posed to direct sunlight or bright light. perature.
■ Position the screen so that it is not in direct ■ The operating temperature of the projector is
sunlight or room light. Light falling directly on from 41°F to 95°F (+5°C to +35°C).
the screen washes out the colors, making ■ The storage temperature of the projector is
viewing difficult. Close the curtains and dim from –4°F to 140°F (–20°C to +60°C).
the lights when setting up the screen in a
sunny or bright room. Do not block the exhaust and intake
vents.
Caution regarding placing of the projec- ■ Allow at least 11 13/16 inches (30 cm) of space
tor between the exhaust vent and the nearest
■ Place the projector on a level site within the wall or obstruction.
adjustment range (8 degrees) of the adjust- ■ Be sure that the intake vent and the exhaust
ment foot. vent are not obstructed.
■ If the cooling fan becomes obstructed, a pro-
tection circuit will automatically put the pro-
jector into standby mode to prevent overheat
damage. This does not indicate a malfunc-
tion. (See pages 48 and 49.) Remove the pro-
jector power cord from the wall outlet and wait
at least 10 minutes. Place the projector where
the intake and exhaust vents are not blocked,
plug the power cord back in and turn on the
projector. This will return the projector to the
normal operating condition.
8
Introduction
runs to decrease the internal temperature for ■ The power supply voltage and the shape of
a while. Unplug the power cord after the cool- the plug may vary depending on the region
ing fan stops. The period the cooling fan runs or country you are using the projector in.
will vary, depending on the circumstances and When using the projector overseas, be sure
the internal temperature. to use an appropriate power cord for the coun-
try you are in.
Caution regarding usage of the projector
■ When using the projector, be sure not to sub- Temperature monitor function
ject it to hard impact and/or vibration, as this
can result in damage. Take extra care with
the lens. Before moving the projector, be sure
to unplug the power cord from the wall outlet, ■ If the projector starts to overheat due to setup
and disconnect any other cables connected problems or blockage of the air vents, “ ” and
to it. “ ” will illuminate in the lower left corner
■ Do not carry the projector by holding the lens. of the picture. If the temperature continues to
■ When storing the projector, re-attach the lens rise, the lamp will turn off, the temperature warn-
cap. (See page 11). ing indicator on the projector will blink, and after
■ Do not expose the projector to direct sunlight a 90-second cooling-off period the projector will
or place next to heat sources. Doing so may enter standby mode. Refer to “Maintenance In-
affect the cabinet color or cause deformation dicators” on page 48 for details.
of the plastic cover.
Remote control Two R-6 batteries 3 RCA to 15-pin Lens cap (attached)
RRMCGA430WJSA (“AA” size, UM/SUM-3, D-sub adaptor CCAPHA024WJSA
HP-7 or similar) (11.8" (30 cm))
QCNWGA075WJPZ
Power cord
for U.S. and
Canada, etc.
(6' (1.8 m))
QACCDA007WJPZ
Optional accessory
■ Lamp unit AN-100LP
Note
• This optional accessory may not be available depending on the region. Please check with your
nearest Sharp Authorized Service Center or Dealer.
10
Introduction
Numbers in Z refer to the main pages in this operation manual where the topic
is explained.
Projector
Top View
Power Lamp indicator
indicator
28, 48 28, 48
48 Temperature warning
indicator
STANDBY/ON 28
button
For turning the
power on and 32 Volume buttons
putting the (–O/Q+)
projector into For adjusting the speaker
standby mode. sound level.
47 Intake vent
HEIGHT 31
ADJUST
lever
Push both sides of the lens cap
to attach or remove.
11
Rear View
47 Exhaust vent
45 Speaker
Intake vent 47
AC socket 28
Connect the Kensington Security
supplied Power cord. Standard connector
Rear adjustment 31
foot
Using the Kensington Lock
• This projector has a
Terminals 1 2 3 4 5 Kensington Security Standard
connector for use with a
Kensington MicroSaver
Security System. Refer to the
information that came with the
system for instructions on how
to use it to secure the
6 7 8 projector.
12
39 MENU/HELP button
KEYSTONE button 33 For displaying adjustment
For entering the 46 and setting screens, and
Keystone Correction help screen.
mode.
RETURN button 39
For returning to the 39 Adjustment buttons
(P/R/O/Q)
previous menu screen • For selecting menu items.
during menu operations. • For adjusting the Keystone
Correction when in the
Keystone Correction mode.
39 ENTER button
For setting items selected
or adjusted on the menu.
36 FREEZE button
For freezing images.
32 Volume buttons
For adjusting the
speaker sound level.
34 RESIZE button
For switching the screen
size (STRETCH, SIDE
PICTURE MODE 36 BAR, CINEMA ZOOM).
button
For selecting the
appropriate picture. 30 INPUT 1, 2, 3 and 4
buttons
For switching to the
respective input modes.
13
Incorrect use of the batteries may cause them to leak or explode. Please
follow the precautions below.
Caution
• Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• Insert the batteries making sure the polarities correctly match the m and n marks inside the battery
compartment.
• Batteries of different types have different properties, therefore do not mix batteries of different types.
• Do not mix new and old batteries.
This may shorten the life of new batteries or may cause old batteries to leak.
• Remove the batteries from the remote control once they have run out, as leaving them in can cause them
to leak.
Battery fluid from leaked batteries is harmful to skin, therefore ensure that you first wipe them and then
remove them using a cloth.
• The batteries included with this projector may run down in a short period, depending on how they are kept.
Be sure to replace them as soon as possible with new batteries.
• Remove the batteries from the remote control if you will not be using the remote control for a long time.
• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.
14
Introduction
Remote control sensor
The remote control can be used to control the
projector within the ranges shown in the illustra-
tion.
Note
• The signal from the remote control can be re-
flected off a screen for easy operation. How-
ever, the effective distance of the signal may
differ depending on the screen material. 30°
When using the remote control
• Ensure that you do not drop, expose to mois- Remote
ture or high temperature. control signal
• The remote control may malfunction under a transmitters
fluorescent lamp. In this case, move the pro- 30° 23n (7 m)
jector away from the fluorescent lamp.
Remote control
15
5 INPUT buttons
3 ON button
7 KEYSTONE button
7 KEYSTONE
button
6 Focus ring
5 INPUT 3 button
6 Zoom ring
6 HEIGHT
ADJUST lever
2. Connect the projector to the video equipment and plug the power
cord into the AC socket of the projector
To AUDIO (INPUT 3, 4)
terminal
To INPUT 3 terminal
AC socket
_PP. 22–28
_P. 28
16
Quick Start
• When pressing the INPUT button on the projector, input mode switches in the following
order: INPUT1 INPUT2 INPUT3 INPUT4
• When using the remote control, press the CINPUT 1/CINPUT 2/DINPUT 3/EINPUT
4 button to switch the INPUT mode. _P. 30
_P. 33
• Unplug the power cord from the AC outlet after the cooling fan stops.
_P. 29
17
Screen
Lens center
L
Note
• Refer to page 20 for additional information concerning “Screen Size and Projection Distance”.
Ceiling-mount Setup
■ It is recommended that you use the optional
Sharp ceiling-mount bracket for this installa-
tion. Before mounting the projector, contact
your nearest Sharp Authorized Service Cen-
ter or Dealer to obtain the recommended ceil-
ing-mount bracket (sold separately).
• AN-XRCM30 ceiling-mount bracket (for
U.S.A.).
• AN-60KT ceiling-mount bracket, its AN-
TK201 and AN-TK202 extension tubes (for
countries other than the U.S.A.).
■ Invert the image by setting “Ceiling + Front”
in “PRJ Mode”. See page 43 for use of this
function.
18
Setup
Menu item ➞ “Front” Menu item ➞ “Ceiling + Front”
■ Table mounted, rear projection ■ Ceiling mounted, rear projection
(with a translucent screen) (with a translucent screen)
Projection
Distance
)
m
– "
m '1
5
2.
.1 8
(2 0"–
– 9"
)
m
7'
m 0'
3
4. "
3.
.8 1
– '5
)
(2 4"–
2 "
m 13
8. 1
1
– '1
9'
.5 "–
)
m
m 26
(3 '7
11
12 "
.1 "–
– 0'4
)
m
(7 '3
.3
23
m 4
6 "–
0. 0
(1 '1
34
19
χ : Picture size (diag.) (in/cm) The formula for picture size and projection distance
L: Projection distance (ft/m) [Feet/inches] [m/cm]
L1: Minimum projection distance (ft/m) L1 (ft) = 0.03541χ / 0.3048 L1 (m) = 0.03541χ
L2: Maximum projection distance (ft/m) χ
L2 (ft) = 0.04098 / 0.3048 L2 (m) = 0.04098χ
H: Distance from the lens center to the bottom of the image (in/cm) H (in) = - 0.32249χ / 2.54 H (cm) = - 0.32249χ
When using a normal screen (4:3) and projecting 4:3 image (SIDE BAR Mode)
Picture (Screen) size Projection distance [L] Distance from the lens center to
Diag. [χ] Width Height Minimum [L1] Maximum [L2] the bottom of the image [H]
300⬙ (762 cm) 240⬙ (610 cm) 180⬙ (457 cm) 42⬘ 8⬙ (13.0 m) 49⬘ 4⬙ (15.0 m) ⳮ46 39/64⬙ (ⳮ118 cm)
270⬙ (686 cm) 216⬙ (549 cm) 162⬙ (411 cm) 38⬘ 5⬙ (11.7 m) 44⬘ 5⬙ (13.5 m) ⳮ41 61/64⬙ (ⳮ107 cm)
250⬙ (635 cm) 200⬙ (508 cm) 150⬙ (381 cm) 35⬘ 7⬙ (10.8 m) 41⬘ 2⬙ (12.5 m) ⳮ38 27/32⬙ (ⳮ99 cm)
200⬙ (508 cm) 160⬙ (406 cm) 120⬙ (305 cm) 28⬘ 5⬙ (8.7 m) 32⬘ 11⬙ (10.0 m) ⳮ31 5/64⬙ (ⳮ79 cm)
150⬙ (381 cm) 120⬙ (305 cm) 90⬙ (229 cm) 21⬘ 4⬙ (6.5 m) 24⬘ 8⬙ (7.5 m) ⳮ23 5/16⬙ (ⳮ59 cm)
100⬙ (254 cm) 80⬙ (203 cm) 60⬙ (152 cm) 14⬘ 3⬙ (4.3 m) 16⬘ 5⬙ (5.0 m) ⳮ15 17/32⬙ (ⳮ39 cm)
80⬙ (203 cm) 64⬙ (163 cm) 48⬙ (122 cm) 11⬘ 5⬙ (3.5 m) 13⬘ 2⬙ (4.0 m) ⳮ12 7/16⬙ (ⳮ32 cm)
70⬙ (178 cm) 56⬙ (142 cm) 42⬙ (107 cm) 9⬘ 11⬙ (3.0 m) 11⬘ 6⬙ (3.5 m) ⳮ10 7/8⬙ (ⳮ28 cm)
60⬙ (152 cm) 48⬙ (122 cm) 36⬙ (91 cm) 8⬘ 6⬙ (2.6 m) 9⬘ 10⬙ (3.0 m) ⳮ9 21/64⬙ (ⳮ24 cm)
40⬙ (102 cm) 32⬙ (81 cm) 24⬙ (61 cm) 5⬘ 8⬙ (1.7 m) 6⬘ 7⬙ (2.0 m) ⳮ6 7/32⬙ (ⳮ16 cm)
χ : Picture size (diag.) (in/cm) The formula for picture size and projection distance
L: Projection distance (ft/m) [Feet/inches] [m/cm]
L1: Minimum projection distance (ft/m) L1 (ft) = 0.04334χ / 0.3048 L1 (m) = 0.04334χ
L2: Maximum projection distance (ft/m) L2 (ft) = 0.05015χ / 0.3048 L2 (m) = 0.05015χ
H: Distance from the lens center to the bottom of the image (in/cm) H (in) = - 0.39468χ / 2.54 H (cm) = - 0.39468χ
20
χ : Picture size (diag.) (in/cm) The formula for picture size and projection distance
Setup
L: Projection distance (ft/m) [Feet/inches] [m/cm]
L1: Minimum projection distance (ft/m) L1 (ft) = 0.0325χ / 0.3048 L1 (m) = 0.0325χ
L2: Maximum projection distance (ft/m) χ
L2 (ft) = 0.03761 / 0.3048 L2 (m) = 0.03761χ
H: Distance from the lens center to the bottom of the image (in/cm) H (in) = - 0.29601χ / 2.54 H (cm) = - 0.29601χ
Note
• Refer to page 18 concerning “Projection distance [L]” and “Distance from the lens center to the
bottom of the image [H]”.
• There are some errors in the values in the diagrams above.
• Values with a minus (-) sign indicate the distance from the lens center below the bottom of the
image.
21
S-video
Video
or connect directly to
AUDIO (INPUT 3, 4).
22
Connections
Component cable
(commercially
available)
23
S-video cable
RCA audio cable*
(commercially available)
(commercially available)
*Use the cable when you want
to enjoy the sound from the
projector’s speaker.
24
RGB Cable
* ø3.5 mm stereo or (commercially available)
mono audio cable
(commercially
Connections
available or
available as Sharp
service part
QCNWGA038WJPZ) * When using the ø3.5 mm mono audio cable, the volume level will be half of
when using the ø3.5 mm stereo audio cable.
Note
• See page 54 “Computer Compatibility Chart” for a list of computer signals compatible with the projec-
tor. Use with computer signals other than those listed may cause some of the functions to not work.
• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your near-
est Macintosh Dealer.
• Depending on the computer you are using, an image may not be projected unless the
computer’s external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously
when using a SHARP notebook computer). Refer to the specific instructions in your computer's
operation manual to enable your computer’s external output port.
25
To INPUT 1 To OUTPUT
terminal To RGB
To RGB output (INPUT 1, 2) input
terminal terminal terminal
Note
• RGB signals and Component signals can be output to the monitor.
26
Note
• ø3.5 mm minijack to RCA audio cable (commercially available) is required.
Connections
• Before connecting, ensure that both the projector and the audio equipment to be connected are
turned off.
• When turning off the projector while it is connected to audio equipment, ensure that you turn off the
audio equipment first and then the projector.
• The volume level of external equipment changes in accordance with the volume level of the projector.
27
Supplied
Power cord
Connecting the Power Cord accessory
AC socket
Info
• English is the factory default language. If you
Turning the Projector on want to change the on-screen display to another
language, change the language according to
Note that the connections to external equip- the procedure on page 43.
ment and power outlet should be done be-
fore performing the operations written be- Lamp indicator
low. (See pages 23 to 28.)
Remove the lens cap and press
S STANDBY/ON on the projector or
fON on the remote control. Power indicator
Note
STANDBY/ON button
• About the Lamp Indicator
The lamp indicator illuminates to indicate the
status of the lamp.
Green: The lamp is on.
Blinking in green: The lamp is warming up
or shutting down.
Red: The lamp is shut down abnormally
or the lamp should be replaced.
• When switching on the projector, a slight flick-
ering of the image may be experienced within
the first minute after the lamp has been illumi-
nated. This is normal operation as the lamp’s
control circuitry is stabilising the lamp output
characteristics. It should not be regarded as
faulty operation.
• If the projector is put into standby mode and ON button
immediately turned on again, the lamp may
take some time to start projection.
28
Info
R
• Do not unplug the power cord during projection
or cooling fan operation. This can cause dam-
age due to rise in internal temperature, as the
cooling fan also stops.
Info
• Keylock does not function while the projector
is: displaying “Menu” screens, in standby
mode, warming up, changing input signals,
operating “Auto Sync” function, or in “Freeze”
mode.
29
30
Make small
adjustments.
Operation
Basic
3 Use the rear adjustment foot to
make the projector level.
• The projector is adjustable ±1 degree
from the standard position.
Note
• When adjusting the height of the projector,
trapezoidal distortion occurs. Follow the pro-
cedures in Keystone Correction to correct the
distortion. (See pages 33 and 43.) Rear adjustment foot
Info
• Do not apply too much pressure on the pro-
jector when the front adjustment foot comes
out.
• When lowering the projector, be careful not to
get your fingers caught in the area between
the adjustment foot and the projector.
• Hold the projector firmly while lifting or carry-
ing.
• Do not hold by the lens area.
31
Note
• Pressing MAV MUTE again will turn the projected
image back on.
32
Note
• The Keystone Correction can be adjusted up
to an angle of approximately ±13 degrees and
the screen can also be set up to an angle of
approximately ±13 degrees (when the resize
mode is set to “STRETCH” (see page 34)).
R On-screen display
1 Press g KEYSTONE to enter the (Keystone Correction mode)
Keystone Correction mode. Keystone 0
• You can also display the on-screen dis- ADJ. END
play of the Keystone Correction mode
with d KEYSTONE on the projector. Shrinks upper side.
(Move the slide bar in the + direction.)
2 Press P/Q or O/R to adjust the
Keystone Correction.
• You can also adjust the Keystone Cor-
rection using the adjustment buttons on
the projector.
Operation
Basic
Note Shrinks lower side.
• Press l RETURN while the on-screen dis- (Move the slide bar in the - direction.)
play of the Keystone Correction mode is on
the screen to return to the default setting.
3 Press g KEYSTONE.
• The on-screen display of the Keystone
Correction mode will disappear.
• You can also use d KEYSTONE on the Info
projector. • While adjusting the image using Keystone
Correction, straight lines and the edges of the
image may appear jagged.
33
Resize Mode
This function allows you to modify or customize the resize mode to enhance the input image. De-
pending on the input signal, you can choose “STRETCH”, “SIDE BAR” or “CINEMA ZOOM” image.
Press HRESIZE.
• See page 43 for setting on menu screen.
RESIZE button
VIDEO
Letter box
480I, 480P, 576I,
576P, NTSC, PAL,
SECAM
Squeezed
34
SVGA
Operation
SXGA Basic
(1280K1024)
5:4 aspect ratio
1280K720
16:9 aspect
ratio
: Cutout area on which images cannot be projected.
35
1 Press NFREEZE.
• The projected image is frozen.
Note
• See page 41 for details on the picture mode.
Auto Sync
(Auto Sync Adjustment)
Note
• When the optimum image cannot be achieved
with Auto Sync adjustment, use the help menu
for manual adjustments. (See page 46.)
36
Español
Useful
37
Page 45
1
* Serviceman only
38
ENTER button
MENU/HELP button
Adjustment buttons
(P/R/O/Q)
MENU/HELP
button
ENTER button
RETURN button
• Press l RETURN to
return to the previous
screen when the menu
is displayed.
1 Press BMENU.
• The “Picture” menu screen for the se-
Example: “Picture” screen menu for INPUT 1
(Component) mode
lected input mode is displayed. Menu item
to adjust. Contrast 0
Features
Bright 0
Useful
Color 0
Tint 0
Sharp 0
CLR Temp 7500K
Bright Boost 1
Progressive 3D Progressive
Lamp Setting Bright
Reset
SEL./ADJ. ENTER END
39
Items to be adjusted
Note
• Press hENTER again to return to the
previous screen.
4 Press O or Q to adjust the item Picture SCR - ADJ PRJ - ADJ Help
selected. Picture Mode Standard
• The adjustment is stored. Contrast 0
Bright 15
Color 0
Tint 0
Sharp 0
CLR Temp 7500K
Bright Boost 1
Progressive 3D Progressive
Lamp Setting Bright
Reset
SEL./ADJ. ENTER END
5 Press BMENU/HELP.
• The menu screen will disappear.
Note
• Menu buttons do not function while the projector is operating the “Auto Sync”, “FREEZE”, or “AV
MUTE” functions.
40
Note
• You can also press G PICTURE MODE on the remote control to select the picture mode. (See
page 36.)
Features
Useful
41
42
See page 33 for details of Keystone Correction. See page 19 for details of Projection (PRJ) Mode.
43
Serviceman only
*
1 Auto Search Function 2 Auto Sync (Auto Sync
This function automatically searches for and Adjustment)
switches to the input mode in which signals are
being received, when the projector is turned on, Selectable items Description
or when the INPUT button is pressed. On Auto Sync adjustment will
occur when the projector is
Note turned on or when the input
When “Auto Search” is set to “On” signals are switched, when
connected to a computer.
• If two or more input signals are found, the pro-
jector selects the input source in the order of Off Auto Sync adjustment is not
INPUT 1 n INPUT 2 n INPUT 3 n INPUT 4 automatically performed.
when you press INPUT (P/R) on the projec-
tor.
• While “Auto Search” is set to “On”, press Note
C INPUT 1,C INPUT 2, D INPUT 3 or • Auto Sync adjustment is also performed by
EINPUT 4 on the remote control to select pressing F AUTO SYNC on the remote con-
an input mode other than the input mode se- trol.
lected by the projector. • The Auto Sync adjustment may take some time
to complete, depending on the image of the
computer connected to the projector.
• When the optimum image cannot be achieved
with Auto Sync adjustment, use manual ad-
justments. (See page 46.)
44
Note
• When the Auto Power Off function is set to 7 Checking the Lamp Life
“On”, 5 minutes before the projector enters Status
standby mode, the message “Enter STANDBY
mode in X min.” will appear on the screen to
indicate the remaining minutes. You can confirm the cumulative lamp usage time
and the remaining lamp life (percentage).
Note
5 Speaker Setting
• It is recommended that the lamp be changed
Selectable when the remaining lamp life becomes 5%.
Description • The lamp life may vary depending on the us-
items
age condition.
On The audio signal is output from the
internal speaker.
Off The audio signal is not output from the
internal speaker.
Features
Useful
45
Adjustment buttons
(P/R/O/Q)
ENTER button
Help
Color is faded or poor
The picture has a green or pink tint
Select the signal type
Adjust “Color” or “Tint”, and change “Bright Boost”
setting to off (“PICTURE” menu).
Return
46
Thinner
Wax
Info
Appendix
47
Lamp indicator
Power indicator
If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,
“ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp
will turn off and the temperature warning indicator will blink, the cooling fan will run, and then the projec-
tor will enter standby mode. After “ ” appears, be sure to perform the measures described on page
49.
■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will be
displayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp will
automatically turn off and then the projector will automatically enter standby mode. At this time, the
lamp indicator will illuminate in red.
■ If you try to turn on the projector a fourth time without replacing the lamp, the projector will
not turn on.
48
Info
• If the temperature warning indicator illuminates, and the projector enters standby mode, follow the
possible solutions above and then wait until the projector has cooled down completely before plug-
ging in the power cord and turning the power back on. (At least 10 minutes.)
• If the power is turned off for a brief moment due to power outage or some other cause while using
the projector, and the power supply recovers immediately after that, the lamp indicator will illumi-
nate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet,
replace the power cord in the AC outlet and then turn the power on again.
• The cooling fan keeps the internal temperature of the projector constant and this function is con-
trolled automatically. The sound of the cooling fan may change during operation because the fan
speed may change and this is not a malfunction.
• Do not unplug the power cord after the projector has entered standby mode and while the cooling
fan is running. The cooling fan runs for about 90 seconds.
Appendix
49
50
Info
• Make sure that you remove the lamp unit by
the handle. Do not touch the glass surface of
STANDBY/ON button
the lamp unit or the inside of the projector.
• To avoid injury to yourself and damage to the
lamp, be sure to carefully follow the steps
below.
• Do not loosen other screws except for the
lamp unit cover and lamp unit.
1
3 Remove the lamp unit cover.
• Turn the projector over. Loosen the user
2
service screw (1) that secures the lamp
unit cover. Remove the lamp unit cover User service screw
(2). (for lamp unit cover)
Appendix
51
Info
• If the lamp unit and lamp unit cover are
not correctly installed, the power will not
turn on, even if the power cord is con- 1
nected to the projector.
Info
• Make sure to reset the lamp timer only when
replacing the lamp. If you reset the lamp timer AC socket
and continue to use the same lamp, this may
cause the lamp to become damaged or ex-
plode.
STANDBY/ON
button
1 Connect the power cord.
• Plug the power cord into the AC socket
of the projector. ENTER button
MENU/HELP
2 Reset the lamp timer.
• While simultaneously holding down button
UMENU/HELP, TENTER and R on the
projector, press SSTANDBY/ON on the R button
projector.
• “LAMP 0000H” is displayed, indicating
that the lamp timer is reset.
52
Appendix
53
Note
• When this projector receives 640K350 VESA format VGA signals, “640K400” appears on the screen.
DTV
Signal Horizontal Frequency (kHz) Vertical Frequency (Hz)
480I 15.7 60
480P 31.5 60
540P 33.8 60
576I 15.6 50
576P 31.3 50
720P 45.0 60
1035I 28.1 50
1035I 33.8 60
1080I 28.1 50
1080I 33.8 60
54
or blinks in red.
The projector cannot be • The keylock is set.
29
turned on or put into the If the keylock is set to “ON”, all the buttons are locked.
standby mode using the
STANDBY/ON button on
the projector.
55
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 5 minutes.
56
57
/ (5)
13 64
11 1/32 (280)
/ (9)
23 64
ø9 7/64 (69.2)
2 7/8 (73) 1 55/64 (47)
/ (11) 4 19/64 (109)
7 16
12 / (315)
13 32
4 7/64 (104)
1 7/8 (47.5)
/ (11)
7 16
1 11/32 (33.8)
59
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor to any
Product the exterior of which has been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal
service or handling, or which has been altered or modified in design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of
purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IMPLIED
WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED
TO THE PERIOD(S) FROM THE DATE OF PURCHASE SET FORTH BELOW. Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described herein,
or to extend the duration of any warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
remedy available to the purchaser. Correction of defects, in the manner and for the period of time described herein, shall constitute
complete fulfillment of all liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full
satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any
way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or
property damage. Some states do not allow the exclusion of incidental or consequential damages, so the above exclusion may not
apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
Warranty Period for this Product: One (1) year parts and labor from date of purchase except for the
Projector Lamp for which the warranty period is ninety (90) days
from date of purchase. After the ninety (90) day warranty period on
the Projector Lamp, parts and labor for a lamp replacement are the
responsibility of the consumer.
Additional Item(s) Excluded from Cleaning of Optical System and/or replacement of any filter.
Warranty Coverage (if any): Labor & materials required to remove and reinstall a suspended
projector in installations not accessible with a standard (8' step)
ladder or ceilings exceeding 12’ in height.
Labor & materials required to remove and reinstall a projector in
complex systems including, but not limited to, projectors installed
in custom enclosures, projectors connected to third party control
and automation systems, and realignment of projectors installed in
“mirrored” rear projection enclosures.
Where to Obtain Service: From a Sharp Authorized Servicer located in the United States. To
find the location of the nearest Sharp Authorized Servicer, call Sharp
toll free at 1-800-BE-SHARP.
What to do to Obtain Service: Contact your Sharp Authorized Servicer to obtain in-home service
for this Product. The Servicer will come to your home and if
necessary to remove the Product for repair at the Servicer’s facility,
the Servicer will reinstall it upon completion of repair. Be sure to
have Proof of Purchase available.
60
LIMITED WARRANTY
Consumer Electronics Products
Congratulations on your purchase!
Sharp Electronics of Canada Ltd. (hereinafter called “Sharp”) gives the following express warranty to the first consumer purchaser for
this Sharp brand product, when shipped in its original container and sold or distributed in Canada by Sharp or by an Authorized Sharp
Dealer:
Sharp warrants that this product is free, under normal use and maintenance, from any defects in material and workmanship. If any
such defects should be found in this product within the applicable warranty period, Sharp shall, at its option, repair or replace the
product as specified herein.
Should this Sharp product fail to operate during the warranty period, warranty service may be obtained upon delivery of the Sharp
product together with proof of purchase and a copy of this LIMITED WARRANTY statement to an Authorized Sharp Service Centre
or an Authorized Sharp Servicing Dealer. In home warranty service may be provided at Sharp’s discretion on any Sharp television
with the screen size of 27” or larger and on any Sharp Over The Range Microwave Oven.
This warranty constitutes the entire express warranty granted by Sharp and no other dealer, service centre or their agent or employee
is authorized to extend, enlarge or transfer this warranty on behalf of Sharp. To the extent the law permits, Sharp disclaims any and
all liability for direct or indirect damages or losses or for any incidental, special or consequential damages or loss of profits resulting
from a defect in material or workmanship relating to the product, including damages for the loss of time or use of this Sharp product
or the loss of information. The purchaser will be responsible for any removal, reinstallation, transportation and insurance costs
incurred. Correction of defects, in the manner and period of time described herein, constitute complete fulfillment of all obligations
and responsibilities of Sharp to the purchaser with respect to the product and shall constitute full satisfaction of all claims, whether
based on contract, negligence, strict liability or otherwise.
WARRANTY PERIODS
Projector 1 year (bulb 90 days)
To obtain the name and address of the nearest Authorized Sharp Service Centre or Dealer, please contact:
SHARP ELECTRONICS OF CANADA LTD.
Mississauga, Ontario
L4Z 1W9
(905) 568-7140
Web site: www.sharp.ca
61