0B-4 Maintenance and Lubrication:
Valve Lash (Clearance) Inspection
ssysocnz0sn4s
Inspect intake and exhaust valve lash and adjust a3.
Refer to "Vaive Lash (Clearance) Inspection: in Section
1D" for valve lash inspection and adjustment procedure.
Engine Oil and Filter Change
ssysocmoso03
+ New and used engine oil can be
hazardous.
Bo suro to road “General Precautions: in
Section 00" and observe what in written.
thoro,
+ Steps 4) 8) must bo performed with
ENGINE NOT RUNNING, For Stop 9), be
‘sure to have adequate ventilation while
engine is running.
————_—_—_———
Before draining engine oil, check engine for cil leakage.
Hany evidence of leakage is found, make sure to correct
defective part before proceeding to the following work.
1) Drain engine oil by removing drain plug.
2) After draining oil, wipe drain plug clean, Reinstall
drain plug.
Tightening torque
Engine oil drain plug (a): 35 N-m (3.6 kgf-m, 25.5
If)
3) Loosen oil fiter by using oil fiter wrench (special
tool) and accessing from between suspension frame
and engine oil pan
‘Special tool
(A): 09915-47320
a
XS
4) Apply engine cil to new oil fiter O-ring
rsaoromvoser
'5) Screw new fiter on oll filter stand by hand until the
{ter O-ring contacts the mounting surface.
A.CAUTION
To tighten oll fiter properly, itis important to
accurately identify the position at which filtor
‘O-ring first contacts the mounting surface.
6) Tighten oil fiter (1) 3/4 tun from the point of contact
with the mounting surface using an ol fiter wrench.
Tightening torque
Oil filter (a}: 14 Nem (1.4 kgf-m, 10.5 Ib-ft)3B.2_ Differential: Front
Repair Instructions
Front Differential Oil Chango
1) Before changing or inspecting oil, be sure to stop
‘engine and lit vehicie horizontally.
2) With vehicle lifted up, check leakage,
IFleakage exists, correct it
NOTE
‘Whenever vohicie is hoisted for any other
service work than oil change, also be sure to
‘check for oil leakage.
3) Remove oil filer plug (2).
4) Remove drain plug (1), and drain old oil
'5) Apply sealant fo thread of drain plug (1), and tighten
itto specified torque,
“A”: Sealant 99000-31260 (SUZUKI Bond
No.1217G)
Tightening torque
Difforontial oil drain plug (a): 23 Nem (2.3 kgf-m,
17.0 lb-A)
6) Pournew specified oil unt oil level reaches bottom
of ol filer plug hole (3) as shown in figure.
NOTE
‘+ Hypoid gear oll must be used for
differential,
+ Itis highly recommended to use API GL-5
80W.90 gear oil.
Differontial oil specification
: APIGL-5 (For SAE classification, refer to
viscosity chart [A] in figure.)
Differential oil capacity (Reference)
£0.85 ~ 1.06 liters (1.8/4.5 — 2.2/1.8 US/Imp. pt.)
7) Apply sealant to thread of level/ filer plug, and then
tighten it to specified torque.
“A”; Soalant 99000-31260 (SUZUKI Bond
No.12176)
Tightening torque
Differential oll level / filler plug (b): 23 Nem (2.3,
kkgf-m, 17.0 tb-ft)