Professional Documents
Culture Documents
Sikadur®-31 C
2-part epoxy adhesive for Sikadur-Combiflex® System and Sika® Dilatec® System
ly
on
DESCRIPTION CHARACTERISTICS / ADVANTAGES
Sikadur®-31 C is solvent-free, moisture tolerant, two ▪ Easy to mix and apply
part epoxy based thixotropic adhesive for bonding ▪ Suitable for both dry and damp concrete surfaces
Sikadur-Combiflex® SG tape and Sika® Dilatec® tape to ▪ Excellent adhesion to many materials
different substrates. It can be used for both internal
and external use.
USES
▪
▪
▪ se
Solvent free
Performs well within a wide temperature range
Completely weather and water resistant
lu
▪ Fast curing
▪ Root resistant
Sikadur®-31 C may only be used by experienced pro- ▪ Good resistance to many chemicals
fessionals. ▪ Thixotropic – suitable for over head and vertical ap-
na
plications
As adhesive for the Sikadur-Combiflex® System ▪ No primer needed
As adhesive for the Sika® Dilatec® System ▪ High mechanical resistance
These systems are used for various applications such ▪ Good abrasion resistance
er
as:
▪ Expansion Joint treatment APPROVALS / CERTIFICATES
▪ Construction Joint treatment
nt
PRODUCT INFORMATION
Fo
PROVISIONAL PRODUCT DATA SHEET 2022-07-12 THE PRODUCT DESCRIBED IN THIS PRODUCT DATA SHEET
Sikadur®-31 C (PDS) IS STILL UNDER DEVELOPMENT AND HAS NEITHER
May 2022, Version 02.0 BEEN FINALLY RELEASED NOR CERTIFIED. THIS PDS MUST
NOT BE USED FOR THE APPLICATION OF THE PRODUCT.
020204030010000115
SIKA MAKES NO REPRESENTATIONS OR WARRANTIES AS
TO THE PERFORMANCE, QUALITY OR OTHER CHARACTER-
ISTICS OF THE PRODUCT.
1/3
Part A+B Mixed : 1.75 kg/l (at +27°C)
All density values at +27°C
TECHNICAL INFORMATION
Compressive strength Curing Time Compressive Strength (ASTM C 579)
1 day ≥ 55 N/mm² at +30°C
7 days ≥ 60 N/mm² at +30°C
ly
sewage, bitumen, bitumen emulsion coatings etc.
Temporary to:
on
Light fuel oil, diesel, diluted alkali and mineral acids, ethanol, methanol,
petrol etc.
These chemical resistance indications may be used to determine the suit-
ability of the sealing system. For more information, please consult Sika
Technical Services.
APPLICATION INFORMATION
se
lu
Mixing ratio Part A : Part B = 2 : 1 (by weight)
Consumption Sikadur®-31 C per metre length
na
2/3
BASIS OF PRODUCT DATA mixing spindle attached to a slow speed electric drill
(max. 500 rpm) until the material becomes smooth in
All technical data stated in this Data Sheet are based consistency and a uniform grey colour. Avoid aeration
on laboratory tests. Actual measured data may vary while mixing. Then, pour the whole mix into a clean
due to circumstances beyond our control. container and stir again for approx. 1 more minute at
low speed to keep air entrapment at a minimum. Mix
only that quantity which can be used within its potlife.
FURTHER INFORMATION
APPLICATION METHOD / TOOLS
Please refer to Sikadur-Combiflex® System and Sika®
Dilatec® System data sheet. Apply the mixed product by hard brush or trowel (for
detailed application, please refer Sikadur®-Combiflex®
ECOLOGY, HEALTH AND SAFETY System data sheet).
User must read the most recent corresponding Safety LOCAL RESTRICTIONS
Data Sheets (SDS) before using any products. The SDS
provides information and advice on the safe handling, Note that as a result of specific local regulations the
storage and disposal of chemical products and con- declared data and recommended uses for this product
tains physical, ecological, toxicological and other may vary from country to country. Consult the local
safety-related data. Product Data Sheet for exact product data and uses.
ly
APPLICATION INSTRUCTIONS LEGAL NOTES
on
SUBSTRATE QUALITY The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
Concrete/masonry/mortar/stone products, are given in good faith based on Sika's cur-
Concrete and mortar must be at least 3–6 weeks old. rent knowledge and experience of the products when
Substrate surfaces must be sound, clean, dry or matt properly stored, handled and applied under normal
se
damp, free from standing water, ice, dirt, oil, grease, conditions in accordance with Sika's recommenda-
coatings, laitance, efflorescence, old surface treat- tions. In practice, the differences in materials, sub-
ments, all loose particles and any other surface con- strates and actual site conditions are such that no war-
taminants that could affect adhesion of the adhesive. ranty in respect of merchantability or of fitness for a
lu
particular purpose, nor any liability arising out of any
Steel legal relationship whatsoever, can be inferred either
Surfaces must be clean, dry, free from oil, grease, from this information, or from any written recom-
coatings, rust, scale, all loose particles and any other
na
Steel
Surfaces must be prepared mechanically using suitable
Fo
All substrates
All dust and loose material must be completely re-
moved from
Sika Services AG all substrate surfaces before application
of the product
Tüffenwies 16 by vacuum / dust removal equipment.
8048 Zürich
MIXING
Tel: +41 58 436 4040
www.sika.com
Pre-batched units:
Mix parts A+B together for at least 2 minutes with a
PROVISIONAL_Sikadur-31C-en-(05-2022)-2.pdf
3/3