aie Si bee
This Standard is confirmed.
See the BSI Catalogue for details.
June 1999
2S 147 : 1976
{Superseaing British Standard $ 147)
UOC 629.7 669,15°24'26'28-194-472 :621.887.2/3
British Standard Aerospace Series : Specification for
0.5 % nickel-chromium-molybdenum steel bars
for the manufacture of forged bolts and forged nuts
Série aérospatiale: Spécification
Barres en acier a 0,5 % de nickel-chrome-molybdéne pour la fabrication
des vis forgées et écrous forgés
Luftraumserie: Spezifikation
Stahistabe mit einem 0,5 % Nickel-Chrom-Molybdan-Gehalt fir die
Herstellung von geschmiedeten Schrauben und Muttern
WOTE. The requirements for che finished bolts
and nuts are given in the relevant
specifications for those products, such as
those in the 'A' series of British Standards.
|, INSPECTION aN TESTING PROCEDURE
General. This British Standard shall be used
in conjunction wich sections one and nine of the
latest issue of British Standard 5 100.
1.2 Sulphur printing or deep etching tests. One
sample shall’ be: Eales fron each Inger for sulphur
printing or deep etching tests,
13 jon, Billets shall be
subjected to ultrasonic examination.
2, MANUFACTURE
The material shall be manufactured by an electric
process.
3. CHEMICAL COMPOSITION
‘Te steel shall contain:
z
Element
Carbon 0.38 | 0.43
Silicon 0,20 | 0,35
Manganese | 0.75 | 1,00
Phosphorus | - 0,025
Sulphur - 0,020
Chromiun 0.40 | 0.60
Molybdenun | 0.20 | 0,30
Nickel 0.40 | 0,70
No COPYING WETHOUT BSI PERMtS:
JN EXCEPT AS PERMITTED BY COPYRIGHT I
4, SURFACE DRESSING
The material shall be overall
5. CONDITION
Bar delivered in
otr: ‘Supplied annealed and
either cold dravn or centreless ground.
5.2 Bar in coil, Bar delivered in coil shall be
supplied spheroidized, cold dravn and suitably
coated for cold forging.
6, HEAT TREATYENT
The final heat treatment applicable to bolts and
nuts made from this material and to their
vepreseatative test samples shall consist of the
Following:
(a) Hardening. Heat at a temperature of
40 + 10 °C, folloved by cooling in oil.
(b) Tempering. Heat unifgrmly at a
temperature between 450 °C and 660 °C,
folloved by cooling in air.MECHANICAL PROPERTIES
7.1 Hardening cost, The hardness shall be not less.
than 500 HY
7.2 Tests in che condition of supply. Material
delivered in the condition specified in 5.1 or
5.2, as appropriate, shall comply with the
following requirenents.
Bar in Bar in
straight coil
lengths
Tensile stvength (wax.) (YPa) 770 aD
Hardness (max.) 229 mB =
NOTE, MPa = x/mn?. Information on SI units is
given in BS 3763 iw Tuternationel System of
Units (S1)' and BS 350 "Conversion factors and
tables.
2S 147 : 1976
N SIZE
The grain size shall be determined in accordance
with BS 4490 "Methods for the determination of the
austenitic grain size of steel", method 3 or
method 5, The grain size shall be no. 5 or finer
‘and no grain shall be coarser than no. 3,
“This British Standard, having been prepared under the direction of
the Arompace Standards Committe, was published under the
futhonty of the Executive Board an 30 November 1976,
Osiris standards tnsivution, 1976
ISBN: 0 580 09500 2
copyright
Users of British Stand
“This doet not preclude the free use, inthe course of implementing
‘the standard, of necesary details uch as symbols and size, type oF
‘rade designstions. Enquiries should be accressed to the
Publications Manager, 101 Pentonville load, London NY 9NO
(Telephone 01-837 8801; Telex 23218)
Contract requirements
Attention i drawn to the fact that this British Standard does not
urport to include all the necessary provisions of « contract.
Revision of British Standards
British Standards are rvitd, when necessary, by the isue ether of
amendment slips oof revised editions. Iti Important that users of
British Standards should ascertain thet they ae in possession of
the latest amandmants or editions.
“The following BSI references relate tothe work on this standard:
Committee reerenee ACE/1S Draft for comment 75/749980C
Amendments issued since publication
‘Amd. No. Date of iseue | Text affected
British Standards Institution
2 Park Street London W1A 2BS - Telephone 01-629 9000 « Telex 266933,a AMD 6836
Amendment No. 1
published and effective from 29 November 1991
to British Standard 2S 147 : 1976
(Aerospace Series)
Specification for 0.5 % nickel-chromium-molybdenum
steel bars for the manufacture of forged bolts and forged
nuts
Jo
Revised text
AMD 6836 Clause 6. Heat treatment
November 1991
Delete all of the existing text of item (a) and substitute
the following,
“(a] Hardening. Heat at a temperature of 840 °C to
870 °C, followed by cooling in oil. The tolerance on the
chosen temperature shall be + 10°C’
ait-0 acens.