Professional Documents
Culture Documents
Page 1 of 4
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336D L EXCAVATOR M4T01262
Configuration: 336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine
i05278252
Camshaft - Install
SMCS - 1210-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2730 Hook 12
B 8T-2998 Lubricant -
NOTICE
https://127.0.0.1:448/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 07/08/2022
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5387 ... Page 2 of 4
Illustration 1 g03356215
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: During the installation of the camshaft, rotate the camshaft in both directions in order to
prevent binding in the camshaft bearing bores.
1. Lubricate the camshaft lobes and the valve lifter bore with a 50/50 mixture of Tooling (B) . Apply
clean engine oil on the camshaft bearing journals. Carefully install camshaft (10) in the cylinder
block.
https://127.0.0.1:448/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 07/08/2022
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5387 ... Page 3 of 4
Illustration 2 g03356207
NOTICE
When installing the camshaft, make sure the number one cylinder is at
top center of the compression stroke with the timing bolt installed in
the flywheel. The camshaft timing is very important. The timing mark
on the camshaft drive gear must line up with the timing mark on the
idler gear. Refer to the Specifications Manual for more information.
2. Correct fuel injection timing and correct valve mechanism operation is determined by properly
timing crankshaft gear (8) and camshaft gear (6) to idler gear (7) . Also, high-pressure fuel pump
https://127.0.0.1:448/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 07/08/2022
336D L Excavators M4T00001-UP (MACHINE) POWERED BY C9 Engine(SEBP5387 ... Page 4 of 4
gear (5) must be timed to camshaft gear (6) . During installation of the front gear, timing marks (9)
on idler gear (7) must be in alignment with the timing marks on crankshaft gear (8) and the timing
marks on camshaft gear (6) . The "0" mark on camshaft gear (6) must align with the timing mark on
idler gear (7) . The "V" mark on camshaft gear (6) must align with the "V" mark on fuel pump gear
(5) .
Illustration 3 g01032348
4. The maximum permissible end play for a worn camshaft is 0.46 mm (0.018 inch). The maximum
permissible end play for a new camshaft is 0.13 ± 0.08 mm (0.005 ± 0.003 inch).
5. Use Tooling (A) to position the valve lifters in the cylinder block.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the rocker arm and the shaft. Refer to Disassembly and Assembly, "Rocker Arm and Shaft -
Install".
Copyright 1993 - 2022 Caterpillar Inc. Sun Aug 7 16:00:09 CST 2022
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1:448/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/si... 07/08/2022