RONEN
UPM-250 Maglev Ultrasonic Grinder
1.Preface
Ultrasonic wave is applied to the grinding and polishing of diamond and synthetic diamond
drawing dies. This new technology has been widely used at home and abroad. The processing
speed and product quality of ultrasonic wave grinding and polishing have been greatly improved
Upm-250 maglev ultrasonic grinding machine is used for repairing and polishing diamond and
synthetic diamond drawing dies in the range of 0.3 to 8.0 mm.
The major improvement of the machine is: there is an automatic swing mechanism of the turntable,
and the power output of the generator is improved by using transistors. The design of ultrasonic
transducer is improved, Direct air cooling, adjust the working pressure by adjusting the dial and
changing the distance between the different pole magnets. The structure is compact and easy to
clean, which improves the production environment.
2.Technical Parameter
1. Input power: AC220 V, 50 Hz
2. Working frequency: About 20KHz
3, Power consumption: < 350W
4, Transducer: piezoelectric, air cooled
5, Pressure mode: Dial adjustment, magnetic pressure
6. Working speed: About 123 rpm
7. Working swing speed: about 30 turns / min
8. Working swing angle: < 12°
01RONEN
3.Working Principle and Equipment Composition
1. This machine uses ultrasonic high-speed vibration to produce impact on the machined surface
through steel needle and die material, grinding the machined surface to achieve the required shape
and size.
2. The equipment is mainly composed of ultrasonic generator, transducer and base.
(1) Ultrasonic generator
The ultrasonic generator is installed ina small cabinet, which is an ultrasonic power supply. The
frequency automatic tracking circuit is used to achieve the best ultrasonic output and vibration effect.
(2) Transducer
The transducer is a high-efficiency piezoelectric cerai
wave into a stable ultrasonic vibration and is air-cooled.
@) Stand
The machine base has a rotatable and swinging mold base, which is installed on a cross carriage, and
moves up and down flexibly by adjusting the dial and magnetic pressure. The cross carriage can be
freely aligned with the center. There is a carriage that can move up and down on the back column, and
‘the transducer is installed on the left carriage.
4. Installation and Use
1. Installation
Place the base on a stable table, move the transducer up and down, adjust it to a proper position and
lock it, And connect the ultrasonic generator with the transducer with the output line, and then insert
the power plug on the base into the power output socket of the ultrasonic sounder. After checking,
insert the power plug of the ultrasonic generator into the power socket with reliable grounding when
the switches are off.
2. Use
According to the size of the processing mold, select the appropriate horn and steel needle, firmly weld
the steel needle on the horn with silver or copper welding, cut the appropriate angle on the grinding
wheel, install it on the transducer and tighten it, put the mold on the mold base, adjust the cross
carriage and the upper and lower carriage of the transducer, make the steel needle insert into the mold
hole, rotate the dial to adjust the magnetic force, then start to put the mold material and turn on the
ultrasonic If necessary, turn on the mold base swing switch, adjust the ultrasonic output power knob to
the appropriate size, and then you can see that the mold material is stirred under the ultrasonic, that is,
the mold processing is in progress.
Note: if necessary, adjust the frequency fine-tuning to optimize the power output.
5. Equipment Composition List and Parts
transducer, which can convert the ultrasonic
lteam
|pm-250 type ultrasonic grinder electrical machine base connecting transducer
|UPM specification
Product certificate
Hom
Hom connector
(Open end wrench for variable amplitude pestle connection (14-17)
(Connecting bolt (m10x30)
Drive belt
allele
oO
NO