SERVICE MANUAL
PARTS LIST
MODEL APp- () 06SECTION 1
SERVICE MANUAL
TABLE OF CONTENTS
TECHNICAL DATA
DISMANTLING OF UNIT . .
CONTROLS AND PARTS LOCATIONS
ADJUSTMENT. 7 hasta
R SOURCE VOLTAGE ADJUSTMENT
SPEED ADJUSTMENT é
TONE ARM HEIGHT ADJUSTMENT
TONE ARM REST HEIGHT ADJUSTMENT
5. OVERHANG ADJUSTMENT
TROUBLE SHOOTING CHART...
=
Bowiraaneun1. TECHNICAL DATA
TURNTABLE SECTION
TPE
PLATTER
SPEED
MOTOR
WOW AND FLUTTER
Less than 0.035% WRMS
Direct drive turntable
325 mm diameter alloy die-cast (Weight: 1.15 kg)
3-1/3 and 45 rpm :
6-pole outer rotor AC servo controlled
SIGNAL TO NOISE RATIO.
Better than $8 dB (IS), 48a (DIN), 69 dB DIN By
SPEED ADJUSTMENT RANGE
TONEARM SECTION
£4% at 33-1/3 rpm, #5% at 45 rpm
TYE
Ssshaped static balanced type stainless steel tubular arm with inside Force
canceller and lateral balance weight
‘ARM HEIGHT ADJUSTMENT RANGE
‘ARM LENGTH
17.3 mm +5, —3 mm (Factory adjusted to 17.3 mm cartridg
230 mm
STYLUS PRESSURE ADJUSTMENT RANGE 0 to 3 gram
‘APPLICABLE CARTRIDGE WEIGHT 4 to 8 grams @ to 12 grams using sub-weigh®)
OFF-SET ANGLE 2
TRACKING ERROR ANGLE Within 2"
OVERHANG 15 mm
SHELL WEIGHT 13.5 grams a
ARM LIFTER [Oi damped type ooo
MISCELLANEOUS
POWER REQUIREMENTS CSA models: 120, 60 Tiz
CEE models: 220V, 50/60 Hz
Other models: 110 to 120/220 to 240V, 50/60 Hz
DIMENSTONS ~ | 4400) x 12808) x 358(D) mm a
173 x$.0 x 14.1) inches
WEIGHT 9 ke (19.8 ths) :
* For improvement purposes, specifications and design are subject to change without notice,DISMANTLING OF UNIT
In case of trouble, etc. necessitating disassembly, please
disassemble in the order shown in photographs. Reas-
semble in reverse order.
TUR TABLE- CONTROLS AND PARTS LOCATIONS
Hinge
Spindle
Tone Arm Lifter
Lateral Weight
- Hinge
Main Weight
Stylus Pressure Scale Ring
Anti-Skating Adjuster
Tone Arm Lifter Lever
Tone Arm Rest
Tone Arm
Pitch Control (45 rpm)
13.
14,
15,
16,
17,
18.
19.
20.
21.
22.
23,
Fig. 1
45 rpm Speed Selector
33/3 rpm Speed Selector
Pitch Control (33-1/3 rpm)
Power Switch
Built-in Strobe Light
Turntable Platter
Strobe Markings
Rubber Mat
Locking Nut
Cartridge Shell
Cartridge Shell Finger Lever
Top ViewSverausene
Fig. 2 Bottom View
- Control P.C Board
AC Servo Motor
. Voltage Selector
}. Voltage Selector P.C Board
Power Transformer
Power Switch
33-1/3 rpm Speed/Pitch Control
45 rpm Speed/Pitch Control
Phase Capacitor C614 4/250V
Power Transistor TR610 2SD198Iv. ADJUSTMENT
sce ADs 1, POWER SOURCE VOLTAGE
a neenaan ADJUSTMENT (Refer to Fig. 3)
Connect a DC Voltmeter to test point TP] and adjust
semi-fixed resistor VROO1 1 kB so that the voltage is
12.0V.
p
SPEED ADJUSTMENT
(Refer to Figs. 3 and 4)
The pitch control of each speed is adjusted with the
outer knob of the Speed Selectors. The movable
range of these Pitch Control Knobs is indicated by
the arrow marks in Fig. 4(b). Therefore, it is neces-
sary to set the Pitch Control Knob to the center of
this movable range prior to speed adjustment
2-1 50 Hz OPERATING FREQUENCY
1) Depress 33 Speed Selector.
“QRooI Me 2) Observe Row 1 revolutions of Strobe markings
Adjust. VR604 100 kB (Fig. 3) until Row 1
Fig.3. Control P.C Board Strobe markings appear to come to a standstill
3) Depress 45 Speed Selector.
4) Observe Row 2 revolutions of Strobe markings,
‘Adjust VR603 100 kB (Fig. 3) until Row 2
Strobe markings appear to come to a standstill
2-2 60 Hz OPERATING FREQUENCY
1) Depress 33 Speed Selector
2) Observe Row 3 revolutions of Strobe markings
Adjust. VR604 100 KB (Fig. 3) until Row 3
Strobe markings appear to come to a stand-still
3) Depress 45 Speed Selector.
4) Observe Row 4 revolutions of Strobe markings.
Adjust. VR603_ 100 KB (Fig. 3) until Row 4
Strobe markings appear to come to a standstill
* Perfect speed adjustment is attained when respec-
tive Strobe markings appear not to move
* Once preset adjustments have been made, further
readjustment is not necessary unless a Pitch
Control is in some way moved. In this case,
re-adjust
aa
eeeeD > pircH
Fig. 4 Speed AdjustmentFig. 5
CcARTROGE
TURNTABLE
Fig. 6
3. TONE ARM HEIGHT ADJUSTMENT
(Refer to Figs. 5 and 6)
‘Tone Arm Height is factory adjusted to 17.3 mm to
accomodate Model APC-5 cartridge. This can be
adjusted by +5,~3 mm according to the height of the
cartridge being used. If Tone Arm Height Adjustment
is necessary, this can be accomplished as follows:
1) Use a hexagonal driver as shown in Fig, S and
loosen the two screws at the base of the tone arm
assembly.
2) While playing a record, adjust tone arm height so
that the tone arm is exactly horizontal as shown in
Fig. 6 and tighten screw.Fig.7
4. TONE ARM REST HEIGHT ADJUSTMENT
(Refer to Fig. 7)
1) As shown in Fig. 7, loosen arm rest fixation screw
with a minus driver.
2) Adjust tone arm rest height so that the tone arm is
exactly horizontal when it is on the arm rest, and
tighten fixation screw.Fig. 8 Overhang Adjustment
5. OVERHANG ADJUSTMENT
(Refer to Figs. 8 and 9)
A 45 rpm Adapter is supplied with your turntable for
son
| “romn use when playing 45 rpm speed discs with a large
5mm center hole. Place the adapter on the turntable
spindle. This adapter is also used for obtaining proper
overhang when a cartridge is installed. The overhang
is determined by the distance between the stylus and
turntable spindle when the Tone Arm is moved to the
center of the turntable. Correct overhang for the
AP-006 is 15 mm. The stylus should be even with the
15 mm groove.
Fig.9 45 rpm AdapterV. TROUBLE SHOOTING CHART
NOTE: For confirmation that wiring, parts, and polarities are in order,
START
Voltage Established
rs
Power Switeh ON
I
Primary sie Fase check, Po 0
Switch cheek, replacement f/——[_Neow light
TS
no_ lr transformer secondary] [Transformer broken ]No
‘Turntable rotation arora a Wize soldering check]
1 ves Ie
Secondary [No Transformer
fuse blown replacement
ry
——1 __
Fuse replacement
feplacenent
ROOT adjostnent, VRB [WO) ag 0 Ts eirenit voliage Bork Done (NO Dove check,
D606 check, replacement eh Sm proper? (DC12V) terminals SV replacement
we 1S YS
ee Ze ERS om + Taw a FW
nes we ee
0
Does pulse appear |, WO Does pulse appear at | no[Does pulse appear |__w0[Broken wire n Restsor, condenser,
at R607 terminals?" | both 2163 terminals? [7 Lat test point Jnotor generator col and solder check
ve i re nS
THODS, 64 TROS, 66 Rotates even when [Ny von Proper valtage between [NO_ [Rotates with TROIO Da check,
cieait check circuit check FTREIO base is grounded] [Motor replacement Red/ Blue motor lead Calletor-Emitter shorted replacement
res eS i
TRRIH, D6OEce, Tora iken wire ]8 J cary corny Pal Cait chek, —] [Rotates even shen R609 ]oO_[~TREID heck
replacement or short aor replacement CollectorsEmitter shorted replacement
i rs Is
10 [Rozates even when Totates even when Totates even when TR605 [NO_[—TRBIG check,
[TR6OS Base is grounded[*—[TR609 base is grounded Motor replacement Soldering check fone carr aes PO] Tote
1 1 1
TREGS check, TROD chook, orates even when TROOS |xo_,[~ TRATE check,
replacement replacement. Collectorsiase shorted replacement
1S
Rotates oven when TROOT FTROOS, COTO, TREOG]_ _no[T2V between TROOG], wo Rovates with Nol Rotates even when
Bsealcan re hres fA 6H ees check, replacement Callector-Emitter TREO? disconnected GUS shorted
Ie res ns Is
TREN? check %E FTROOG, COUT. TROOG]__ yo 12V between TROOA TROT check, DOS check,
replacement check replacenent Collector Emitter replacement replacement
res
TET check,zeL2sz
M3IA Gaq01dxXS e3? Ga
auvog od b W
ios
WaAOd
eo33-I/3rpm 45rpm
+ TT
|
| |
input } 90myv | l5my
| 1283,3Hz | f= ILIHE,
L z
f ee
(a) | lav lav
ic 1
33-1/3 1pm 45rpm
Ne No
(B) / -bv -by z
oy oH g g[_ PiTcH
Sea ple CONTROL
Bise foe TI
8/89 |3e2
I ae #88
(c) [ lav ] lev a i
4 A Soe teet A EcB
28c732
ack
280235
2spi98
PICK UP COIL At
R614
1.5K
151588
TREOB|
2| 2
1622
*
isk 22/16
TREO! to 609 28C732
POWER] \o
sooz b -
r20v)
ac |
1
1
M10 ,120/220 , 240V
50/60Hz
a
ct
| }0.0171000
HOV. 220v.
‘240V
280732
(D)
(E)
(F)
TP2
(6)
(H)
TREIO
280198
33-1/3rpm 45rpm
IN ie
68mv 68mv
2 (ile
j-l2ms--4 | 9ms
t t
lav lav
U 2
: Inne
SERVO MOTOR
NOTE
‘SCM= 900
UNLESS OTHERWISE SPECIFIED
ALL RESISTORS IN OHMS 1/4W(J)
ALL CAPACITORS IN pF S5OWV(J)
Pe pyr
AP-006
SCHEMATIC DIAGRAM
no. 1540442A