Professional Documents
Culture Documents
Trio 330 Poster
Trio 330 Poster
TRIO 330
must be sealed with plugs ø 20/24, item no. 030300.
60 72 • More information can be found in the TRIO assembly
instructions.
72
60
9.
Without exception, valid safety regulations must be observed
Extremely cost-effective 3.30 m high panel formwork in those countries where our products are used.
WDA 10
Ties
Permissible fresh concrete pressure for
60
Basic rule: Ties the TRIO 330. Elements certified
TRIO 330 panels have an asymmetrical for extended formwork according to guidelines issued by the
72 tie arrangement. When placing the Güteschutzverband Betonschalungen
elements, the tie hole must be in (Quality Protection Association for
the upper position. Wrong application Concrete Formwork), GSV.
results in more ties being used than is
necessary. 82.5 kN/m2 triangular load, DIN 18202,
Extension
Table 3, Line 7, with 2 ties.
For standard element joints On external corners For filler timbers up to 100 mm For timber extensions
57.5
1.175 m
in only one step! durch neutrales Prüfinstitut
External formwork: with panel TR 90
Internal formwork: with TRIO Corner TE
240 Güteschutzverband
1.075 m
Test report
Betonschalungen
Adapting to wall thicknesses using
240
available on
request.
TRIO wall thickness compensation
3.30 m
3.30 m
WDA 5, WDA 6 or timber infills
Filler timber
1.55 m
1.075 m
72
2. With WDA or timber
M
TR
WDA 5/6
60
E
57.5
72
57.5
TG
E
TG
TE 4.
(180)
72
200
WDA 5 (6)
90
TRM 72
60
3. With TRM 72
The TRIO shaft element
Filler timber allows complete shaft
TRM 72
TRM 72 formwork units to be moved
as one unit.
A 25 mm all-round
TRM 72
TRM 72 clearance for striking is
created when the formwork
panels are pulled.
Filler timber
When striking,
1. With 330x240 2. With TRM 72 3. With TR 30 4. With WDA or timber infills 2. lever crowbar
upwards.
TE
(240)
WDA 5 (6)
90
TRM 72
30
TAR 85
240
Quick and easy solution up to 100 mm. Economical solution. Optimal visible surface solution. TRIO articulated corner TGE for angles Internal formwork: External formwork:
90
With timber, or timber and formlining With filler plates from 60 – 360 mm. With formlining and filler support of 75° and more – for internal and with TR 60 or TR 30 panels and articulated with multi-panel TRM 72 and
plus BFD alignment coupler. Filler Plate LA 330, Item No. 054384. TPP, Alu 330, Item No. 101829. TE external corners alike. corners articulated corners
85
TAR 2
7
75°
TRM 72
Filler timber
5. TRM
30
TE 60
30
90
TE TE
30
TE TE
TE Filler timber
72
TAR 85
400
TRM 72
90
TE
7. 3.
R 7
60 TGE
85 2
135°
TRM 72
TRM 72
60
Using the TRIO MT/MTF stopend panel with continuous Up to max. 200 mm Basic rules for corners Internal formwork: External formwork:
240 - 330
TAR 85
30
Timber
2 WDA 5 (6) WDA 5 (6)
Additional BFD for Hook tie
360
240
TRM 72
TRM 72
TAR 85 TE
72
TE
72
Up to max. 860 mm
60
60
TRM 72
TAR 85
860 mm
max.
Stopend panel120
390
(360)
min.
AT MTF AT AT MT AT
c c c c TE
TE
The concrete cover c is 25 mm or 50 mm. Timber infills
60
TAR 85 Stopend tie
TAR 85
TE
TE
Push-Pull Props and Kicker Braces TE
TRM 72
TAR 85
72
72
72
aligning the formwork as well as table, are attached to the panels by base plates. 60 60 60
420
Alignment couplers and all-round struts Extension up to max. 8.10 m high can
Verankerungstiefe hnom* [mm] 115
Stacking Device TRIO, galv. Lifting Hook TRIO Lifting Gear Combi-2 TRIO
empfohlene Last in B10
Bohrtiefe hO * [mm] 140 ungerissenem Beton oder ungeris- empf. FQ [kN] 10,4
sener Beton bei erreichter Festigkeit
Bohrer ø (Hammerbohrer DIN 8035) dO [mm] 18 `w * 10 N/mm2 empf. FZ [kN] 10,4
Sicherheitsbeiwert s = 4
Max. Anzugsdrehmoment MDmax [Nm] 150
empfohlene Last in B25
Perm. load of 500 kg/piece Perm. load of 2.9 t with 45° lifting gear angle.
empf. FZ [kN] 16,4
a
ar
a
r a
db [mm] 21
SW 30
PERI GmbH
Postfach 12 64
For safe stacking of 5 TRIO panels max. lifting gear angle of 30°. The pins are used to move stacks of panels located on the ground. easier.
a a
89259 Weißenhorn
of any size. TRIO lifting hooks or TRIO stacking devices are attached to the
tfix
at maximum prop spacing 9.7 9.7 9.8 9.8 9.8 9.6 9.5 8.5 9.3 10.1
F2 Stacking Device TRIO Lifting Hook TRIO
Item no. 023390 Item no. 023690
Actual kicker load FAV [kN]
at maximum prop spacing 2.1 2.3 2.2 2.2 2.3 2.6 2.6 2.3 2.1 1.9 PERI Paletten und
Stapelrungen
TRIO Versetzhaken 1,5t
Art.-Nr. 023690
TRIO Kombigehänge-2
Art.-Nr. 044760
from top of formwork 1.0 1.2 1.5 1.8 2.0 2.0 y2 4.5 5.5 6.2 6.9
y
0.5 kN/m2
transferred into the building at the foot of the push-pull prop. Pallets and Stacking Devices Lifting Hook TRIO Lifting Gear Combi-2 TRIO
FAV FAV
Wind loads: h < 8m = 0.5 kN/m2 60° 60° 60°
8m< h < 20m = 0.8 kN/m2
x x2
x1
510
TRIO Panels
Width
240 120 90 60 30 72 TE TRM 72 TGE
Height
Internal corner Multi-purpose Articulated
with 30 cm leg panel with corner from 75°
length continuous tie to 285° for
hole strip internal and Max. 5 TRIO panels 330 x 240 can
external corners be transported with the lifting gear
540
combi-2.
Secure stack of panels by means of
tie rods to prevent panels moving
during lifting.
TR 330
Scaffold Bracket
TRG 80 Item no. 023670
Handrail Post Holder TRIO
TRG 120 Item no. 023680 Item no. 101592
Two TAR 85 compensation walers and
two BFD alignment couplers are required
570
m2 6.48 3.24 2.43 1.62 0.81 1.94 1.62 1.94 1.62 Concreting Platform 120 x 270
Item no. 022570 022510 022520 022550 022560 022530 022580 022540 023200 Item no. 022950
Weight 329.00 kg 159.00 kg 112.00 kg 80.30 kg 52.90 kg 89.20 kg 68.80 kg 93.80 kg 94.80 kg
a truck.
m2 2.88 1.44 1.08 0.72 0.36 0.86 0.72 0.86 0.72
Item no. 022514 022600 022610 022640 022650 022620 022660 022630 032300
Weight 163.00 kg 67.90 kg 52.80 kg 39.50 kg 24.90 kg 43.50 kg 32.80 kg 51.90 kg 43.60 kg
660
TR 60
170
320
Edition 06/2007
PERI Product Range
Poster
Additional Systems
Plywood
Formwork Girders
Stopend Systems
Pallets
Transportation Containers
PERI GmbH
Formwork Scaffolding
Engineering
P.O. Box 1264
89259 Weissenhorn
Germany
Tel +49 (0)7309 9 50- 0
Fax +49 (0)7309 9 51- 0
info @ peri.de
Edition 06/2007 www.peri.de
PERI Product Range
Poster
Additional Systems
Plywood
Formwork Girders
Stopend Systems
Pallets
Transportation Containers
PERI GmbH
Formwork Scaffolding
Engineering
P.O. Box 1264
89259 Weissenhorn
Germany
Tel +49 (0)7309 9 50- 0
Fax +49 (0)7309 9 51- 0
info @ peri.de
Edition 06/2007 www.peri.de