Professional Documents
Culture Documents
Ds 24vin Micro Family-3044964
Ds 24vin Micro Family-3044964
24V Input
Actual size:
2.28 x 1.45 x 0.5in ® S
• Operation to 16V at 75% power For details on proper operation please refer to the:
after start up Design Guide & Applications Manual for Maxi, Mini, Micro Family.
• Input surge withstand: 50V for 100ms
• DC output: 3.3 – 48V Absolute Maximum Ratings
• Programmable output: 10 – 110%
Parameter Rating Unit Notes
• Regulation: ±0.4% no load to full load
+IN to –IN voltage –0.5 to +53 VDC
• Efficiency: Up to 89%
PC to –IN voltage –0.5 to +7.0 VDC
• Maximum operating temp: 100°C,
PR to –IN voltage –0.5 to +7.0 VDC
full load
SC to –OUT voltage –0.5 to +1.5 VDC
• Power density: up to 91W per cubic inch
Isolation voltage
• Height above board: 0.43in [10,9mm]
IN to OUT 3000 VRMS Test voltage
• Parallelable, with N+M fault tolerance IN to base 1500 VRMS Test voltage
• Low-noise ZCS/ZVS architecture OUT to base 500 VRMS Test voltage
• RoHS Compliant (with F or G pin option) Operating Temperature –55 to +100 °C M-Grade
Storage Temperature –65 to +125 °C M-Grade
Product Overview 500 [260] °F [°C] <5 sec; wave solder
Pin soldering temperature
These DC-DC converter modules use 750 [390] °F [°C] <7 sec; hand solder
advanced power processing, control and Mounting torque 5 [0.57] in.lbs [N.m] 6 each
packaging technologies to provide the
performance, flexibility, reliability and cost
effectiveness of a mature power component.
High-frequency ZCS/ZVS switching provides
high power density with low noise and
high efficiency.
Part Numbering
e.g. V24C12T100BL2 24C B
Product Type Product Grade Temperatures (°C) Output Power Pin Style Finish Baseplate
Output Voltage VOUT POUT
Grade Operating Storage Blank: Short Tin/Lead Blank: Slotted
V = Standard 3V3 = 3.3V L: Long Tin/Lead
S = Enhanced E = –10 to +100 –20 to +125 3.3V 75W, 50W 2: Threaded
5 = 5V S: Short ModuMate Gold
efficiency 8 = 8V C = –20 to +100 –40 to +125 5V 125W, 100W, 50W 3: Through-hole
T = –40 to +100 –40 to +125 N: Long ModuMate Gold
(avail. ≤12 12 = 12V 8V 100W F: Short RoHS Gold
VOUT only) 15 = 15V H = –40 to +100 –55 to +125 12V 150W, 100W, 50W
M = –55 to +100 –65 to +125 G: Long RoHS Gold
24 = 24V 15V 150W, 100W, 50W K: Extra Long RoHS Gold
28 = 28V 24V 150W,100W, 50W
36 = 36V
48 = 48V 28V 150W, 100W, 50W
36V 100W, 50W
48V 150W, 100W, 50W
Output voltage set point ±1 % Of nominal output voltage. Nominal input; full load; 25°C
Line regulation ±0.02 ±0.20 % Low line to high line; full load
Note: The permissible load current must never be exceeded during normal, abnormal or test conditions. For additional output related application information,
please refer to output connections on page 10.
PC module disable 2.3 2.6 2.9 VDC Switch must be able to sink ≥4 mA. See Figure 2
PC module alarm 0.5 VAVG UV, OV, OT, module fault. See Figures 3 and 5
PC resistance 0.9 1.0 1.1 MΩ See Figure 3, converter off or fault mode
PR receiver threshold 2.4 2.5 2.6 Volts Minimum pulse width: 20ns
SC capacitance 0.033 µF
SC module alarm 0 VDC With open trim; referenced to –Sense. See Figure 7
Isolation test voltage (IN to OUT)* 3000 VRMS Complies with reinforced insulation requirements
Isolation test voltage (IN to base)* 1500 VRMS Complies with basic insulation requirements
Isolation test voltage (OUT to base)* 500 VRMS Complies with operational insulation requirements
Temperature limiting 100 115 °C See Figures 3 and 5. Do not operate coverter >100°C.
C2* C4*
4.7nF 4.7nF
+IN +OUT
F1* PC
C1* SC
PR
0.2µF
–IN –OUT
C3*
4.7nF C5*
4.7nF
Figure 1 — Basic module operation requires fusing, grounding, bypassing capacitors.* See Maxi, Mini, Micro Design Guide.
Output Connections and Considerations protected for conditions such as lead reversal, noise pickup, open
circuit or excessive output lead resistance between the sense
The permissible load current must never be exceeded during
point and the converters output terminals. For applications that
normal, abnormal or test conditions. Converters subject to dynamic
may draw more than the rated current, a fast acting electronic
loading exceeding 25% of rated current must be reviewed by
circuit breaker must be utilized to protect the converter. Under
Vicor Applications Engineering to ensure that the converter will
no circumstance should the rated current be exceeded. Utilizing
operate properly.
or testing of current limit or short circuit current will damage the
Under dynamic-load, light-load or no-load conditions, the converter converter. Ensure that the total output capacitance connected to
may emit audible noise. Converters that utilize remote sense may the converter does not exceed the limits on Page 16, “Maximum
require compensation circuitry to offset the phase lag caused Output Capacitance”, of the design guide.
by the external output leads and load impedance. If an external
remote-sense circuit is used, the remote-sense leads must be
Comprehensive Online Application Information The Design Guide and Applications Manual includes:
• Application circuits
• Design requirements
• EMC considerations
• Current sharing in power arrays
• Thermal performance information
• Recommended soldering methods
• Accessory modules – filtering, rectification, front-ends
• Mounting options
• ...and more.
Also at vicorpower.com
• PowerBench online configurators
• Over 20 Application Notes
• Online calculators – thermal, trimming, hold-up
• PDF data sheets for ALL Vicor products
Input Undervoltage
Input Overvoltage
+IN +OUT +IN Over Temperature
Module Faults +OUT
Auto
Restart
PC
SW1
PC 2 – 20ms typ.
50Ω
SC f(VIN)
1kΩ SC
SW2 SW3
PR PR
Disable 1MΩ
5.7VDC
(0 – 3mA) 6kΩ
1.23
VDC
–IN –OUT –IN SW1, 2, & 3 shown –OUT
in "Fault" position
+IN +OUT
Fault 400µs typ.
5.7V
PC PC
4kΩ SC
"Module
PR
Enabled"
1.23V 2 – 20ms typ.
SC
–IN –OUT
PC PC
SC SC
4k PR PR Alarm
1.00V
–IN –IN –OUT –OUT
–IN
Trim Down
4.7nF
1. This converter is not a constant-power device – it has a Parallel
Bus
constant current limit. Hence, available output power is
reduced by the same percentage that output voltage is
Figure 9 — AC-coupled single-wire interface
trimmed down. Do not exceed maximum rated output current.
* See Maxi, Mini, Micro Design Guide
2. The trim-down resistor must be connected between the SC
and –S pins. Do not bypass the SC pin directly with a capacitor. 4.7nF
+ +IN
Trim Up 0.2µF PC
T1 R1* Module 1
1. The converter is rated for a maximum delivered power. To PR
ensure that maximum rated power is not exceeded, reduce
–IN
maximum output current by the same percentage increase in –
4.7nF
output voltage.
4.7nF
2. The trim-up resistor must be connected between the SC and +IN
+S pins. Do not bypass the SC pin directly with a capacitor. PC
0.2µF Module 2
T2 R1*
3. Do not trim the converter above maximum trim range (typically PR
+10%) or the output over voltage protection circuitry may –IN
be activated.
4.7nF
Parallel
Bus
36.5k
+OUT PS2701
1.65k 470pF
+ 200mV + R10
U3 1.24k
Module #2 L • At the discretion of the LM10 Gnd
Pin Styles*
F Short RoHS Gold Select for RoHS-compliant inboard solder, socket or SurfMate mounting
G Long RoHS Gold Select for RoHS-compliant onboard solder or socket mounting
K Extra Long RoHS Gold Select for RoHS compliance onboard mounting for thicker PCBs
(not intended for socket or Surfmate mounting)
* Pin style designator follows the “B” after the output power and precedes the baseplate designator.
Ex. V24C12T100BN2 — Long ModuMate Pins
Storage
Vicor products, when not installed in customer units, should be
stored in ESD safe packaging in accordance with ANSI/ESD S20.20,
“Protection of Electrical and Electronic Parts, Assemblies and
Equipment” and should be maintained in a temperature controlled
factory/ warehouse environment not exposed to outside elements
controlled between the temperature ranges of 15°C and 38°C.
Humidity shall not be condensing, no minimum humidity when
stored in an ESD compliant package.
Converter Pins
No. Function Label
1 +IN + Ref Dwg. 37207 rev 5
Primary
2 PC
Control
3 Parallel PR
4 –IN –
5 –OUT –
Secondary
6 SC
Control
7 +OUT +
SLOTTED BASEPLATE
0.800* 0.800*
20,32 INBOARD ONBOARD INBOARD ONBOARD INBOARD ONBOARD
20,32 INBOARD ONBOARD
SOLDER SOLDER SOLDER SOLDER SOCKET SOCKET
0.525* 0.525* SOCKET SOCKET
MOUNT MOUNT MOUNT MOUNT MOUNT SURFACE MOUNT
13,34 13,34 MOUNT SURFACE MOUNT
0.275* PLATED
PLATED SHORT PIN STYLE LONG PIN STYLE SHORT PIN STYLE
SOCKET
LONG PIN STYLE
SURFACE MOUNT SOCKET
ALUMINUM SURFACE MOUNT ALUMINUM
THRU HOLE 6,99 THRU HOLE 0.094 ±0.003 0.094 ±0.003 0.183 BASEPLATE
(7X) 0.094 ±0.003 0.094 ±0.003 (7X) 0.183 ±0.003 ±0.003
BASEPLATE N/A
DIA 0.145* DIA 2,39 ±0,08 N/A
2,39 ±0,08 4,65 ±0,08
2,39 ±0,08 2,39 ±0,08 4,65 ±0,08 PINS STYLES
3,68 0.133 PINS STYLES
0.133 SOLDER:TIN/LEAD PLATED
3,38 SOLDER:TIN/LEAD PLATED
3,38 MODUMATE: GOLD PLATED COPPER
MODUMATE: GOLD PLATED COPPER
1 2 3 4 RoHS: GOLD PLATED COPPER RoHS: GOLD PLATED COPPER
1 2 3 4
1.734**2.000* 1.734**
44,04
For Soldering Methods and Procedures
44,04 50,80
Please refer to:
The Maxi, Mini Micro Design Guide.
7 6 5 7 6 5
Vicor Corporation
25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
Fax: 978-475-6715
www.vicorpower.com
email
Customer Service: custserv@vicorpower.com
Technical Support: apps@vicorpower.com
©2019 – 2021 Vicor Corporation. All rights reserved. The Vicor name is a registered trademark of Vicor Corporation.
All other trademarks, product names, logos and brands are property of their respective owners.
Authorized Distributor
Vicor:
V24C12M50BG3 V24C28C100BL V24C36C50BG3 V24C24T100BL3 V24C15T50BL2 V24C5M100BL
V24C24C50BL V24C12C100B V24C15C50BL2 V24C5T100BL V24C5E125BG V24C36C100BL V24C5T50B
V24C28T50BG V24C8T100BL3 V24C12H50BL V24C5M50B2 V24C8C100BL V24C12T100BL V24C5C50BL
V24C5C100BL V24C5E50BN3 V24C5M100BN2 V24C24T100BL V24C15T50BL3 V24C15C50BG V24C36T100BL2
V24C5T50BL3 V24C12C50BL V24C12C100BL V24C28T100BN2 V24C48T50BL V24C36C50BL V24C28C50BL
V24C24C100BL V24C3V3M75BN2 V24C12C150BL V24C15C50BL V24C12H100BL V24C12E150BG
V24C5T50BL2 V24C3V3C75B V24C3V3M50B2 V24C48M50B2 V24C5H50BL3 V24C48C100BL V24C15C100BL
V24C24T100BG V24C8M100BL V24C12T100B2 V24C5T50BG V24C12T50BL V24C12T100BL2 V24C36H50BL2
V24C3V3T50BL3 V24C48C50BL V24C15H50BL2 V24C15C50BF3 V24C15T50BG V24C5T50BG2
V24C28M150BN V24C12T100BG V24C15H100BL V24C3V3C50BL V24C5T100B V24C24H100BL
V24C3V3C75BL2 V24C12M50BL3 V24C15M100BL3 V24C3V3M75BL3 V24C24C150BL V24C24C100B
V24C24H50BL V24C48C150BF2 V24C28C100BG V24C36C100BG V24C12C100BG V24C5C100BG
V24C12E150BG2 V24C5H100BL2 V24C5C100BL2 V24C12E50BN V24C28H150BG V24C15T50BL
V24C24H100BL3 V24C5H50BG V24C24C100BL3 V24C48E100BF V24C5M100BL2 V24C15M100BL2
V24C12E100BG V24C12M100BL V24C5T125BL2 V24C12C100BS V24C5C50B3 V24C12T150BL2 V24C12E50B
V24C5E50BL V24C12C150BL2 V24C12H50BL3