Professional Documents
Culture Documents
% Initial Strength @ 21 °C
(psi) (6,670)
Tensile Strength, ISO 527-3 MPa 10 250
(psi) (1,450) 80 °C
Tensile Modulus, ISO 527-3 MPa 114 200
(psi) (16,500) 100 °C
60 °C
150
Elongation, at break, ISO 527-3, % 58
100
50
TYPICAL PERFORMANCE OF CURED MATERIAL
After 7 days @ 22 °C 0
0 500 1000 1500 2000 2500 3000
Shear Strength Time, hours
Lap Shear Strength, ISO 4587:
Aluminum MPa 11.9 Chemical/Solvent Resistance
(psi) (1,725) Shear Strength on Stainless steel Lapshears, Aged under
Stainless Steel MPa 8.5 conditions indicated and tested @ 22°C
(psi) (1,230)
% of initial strength
Galvanized Steel MPa 3.5
(psi) (510) Environment °C 100 h 500 h 1000 h 3000 h
Polycarbonate MPa 8.9 Water 22 150 95 70 30
(psi) (1,290) Water 60 40 25 35 15
ABS MPa 5.5
(psi) (800) 98% RH 40 110 30 35 20
PVC MPa 10.3 Isopropanol 22 85 110 60 15
(psi) (1,495) Acetic Acid, 10% 22 90 120 70 10
Epoxyglass MPa 9.4
Sodium hydroxide, 4% 22 110 110 60 55
(psi) (1,365)
Wood (Mahogany) MPa 9.1 Motor oil (5W40) 22 115 120 120 120
(psi) (1,320)
Trademark usage
Not for product specifications
Except as otherwise noted, all trademarks in this document
The technical data contained herein are intended as reference
only. Please contact your local quality department for are trademarks of Henkel Corporation in the U.S. and
assistance and recommendations on specifications for this elsewhere. ® denotes a trademark registered in the U.S.
product. Patent and Trademark Office.
Storage
Store product in the unopened container in a dry location. Reference 0.0
Storage information may be indicated on the product container
labeling.
Optimal Storage: 20°C ± 5°C. Storage below 15°C or
greater than 25 °C can adversely affect product properties.
Component B is frost sensitive. Material removed from
containers may be contaminated during use. Do not return
product to the original container. Henkel Corporation cannot
assume responsibility for product which has been
contaminated or stored under conditions other than those
previously indicated. If additional information is required,
please contact your local Technical Service Center or
Customer Service Representative.
Conversions
(°C x 1.8) + 32 = °F
kV/mm x 25.4 = V/mil
mm / 25.4 = inches
µm / 25.4 = mil
N x 0.225 = lb
N/mm x 5.71 = lb/in
N/mm² x 145 = psi
MPa x 145 = psi
N·m x 8.851 = lb·in
N·m x 0.738 = lb·ft
N·mm x 0.142 = oz·in
mPa·s = cP
Note
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. It is the user's responsibility to
determine suitability for the user's purpose of any production
methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons
against any hazards that may be involved in the handling and
use thereof. In light of the foregoing, Henkel Corporation
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a