Professional Documents
Culture Documents
WARNING
Identifies information about practices or circumstances that can cause an explosion in a
!
hazardous environment, which may lead to personal injury or death, property damage,
or economic loss.
ATTENTION
Identifies information about practices or circumstances that can lead to personal injury
Identifies information that is critical for successful application and understanding of the
IMPORTANT
product.
! I, Division 2.
• Do not replace components or disconnect equipment
unless power has been switched off or the area is known to
be non-hazardous.
• Do not connect or disconnect components unless power
has been switched off or the area is known to be
non-hazardous.
• All wiring must comply with N.E.C. article 501-4(b).
Environnements dangereux
Cet équipement est conçu pour être utilisé dans des environnements de Classe I,
Division 2, Groupes A, B, C, D ou non dangereux. La mise en garde suivante
s’applique à une utilisation dans des environnements dangereux.
Overview
In addition to providing the module’s electrical specifications, this document tells
you how to:
• install the module into the chassis
• install the Octal Filter Label
• wire the module
We assume you have already installed your chassis and power supply. If not, please
refer to the installation instructions for these products before preceding.
!
IMPORTANT The first slot of the chassis is reserved for the processor or
Remote I/O module Catalog Number 1747-ASB for a remote
chassis.
1. Disconnect Power
Specifications
OUTPUT
EFUSE LED
EFUSE
Front View
1. The E-Fuse LED will illuminate provided that power is applied to the
module. (power required: 5V dc via backplane and load power via an
external supply)
1. Remove the SLC 500 system power and correct the conditions causing the
short circuit or overload current condition.
2. Restore the SLC 500 system power. The module automatically resets and
resumes control of the output channel and associated load.
TIP The octal label kit can be obtained from your Allen-Bradley
Distributor. The octal kit is ordered based on the catalog number
of the I/O module. Please refer to the SLC 500 Modular Hardware
Style User Manual, publication 1747-UM011, or the Control and
Information Products Price List, publication ACIG-PL001, for a
complete listing of octal label kit catalog numbers.
Lower
Retaining
Arm
Keyed Male User Terminal Block
MIL-C-83503 Panel Lights, (For wire termination,
Header Buttons, Etc. refer to page 14
for the wiring diagrams
of the I/O modules.)
(1) Maximum user cable length is dependent on how much voltage drop (current x (ohms/ft.) x (feet)) the user’s system can
tolerate. The user’s system should take into account the minimum turn-on voltage required by external loads connected to
the 32-point output modules and all of the voltage drops associated with wiring to and from the load, terminal blocks,
power sources and the module itself.
1492-CABLExx (2)
Connects 32-point module
to DIN rail mountable
0.32 in. (8 mm) REF.
terminal block
32-Point I/O Module
Male MIL-C-83503 Header
24 to 12 AWG
(0.2 to 4mm2)
(1) To maintain group isolation provided by 32-point I/O modules, use a 1492 terminal block that provides group isolation.
Consult 1492 documentation or your Allen-Bradley Sales Office for additional information.
(2) Maximum user cable length is dependent on how much voltage drop (current x (ohms/ft.) x (feet)) the user’s system can
tolerate. The user’s system should take into account the minimum turn-on voltage required by external loads connected to
the 32-point output modules and all of the voltage drops associated with wiring to and from the load, terminal blocks,
power sources and the module itself. See the table on page 13 for voltage drop values for the 1492 cables shown above.
V3 V3 16
15 V2 V2
31 V4 V4
Bottom Top
Terminal Terminal
The stick-on labels of the 1492 Interface Module are abbreviated as follows: +V1 =
V dc 1, +V2 = V dc 2, CM1 = Com 1, etc.
Refer to page 11 for information on wiring 32-point I/O modules and how control
devices interface with 32-point I/O modules.
3. Crimp with DDK crimp tool 357J-5538. Equivalent Amp part numbers are:
pin - #87666-2, connector - #102387-9, and crimp tool - #90418-1.
4. Insert the wire contact into the socket as shown in Figure 3 and 4. Check to
make sure that the tang, shown as “A” in Figure 4, is properly latched by
lightly pulling on the wire.
4 mm
(5/32 in) Tang
4 mm
(5/32 in)
Wire
Stop
Figure 1 Figure 2
Figure 3 Figure 4
Wiring Diagrams
In this document, the wiring diagrams include both For SLC
decimal and octal numbers. To wire your module when (decimal)
used in an SLC system, use the decimal numbers. To IN 14
For PLC
wire your module when used in a PLC system, use the 16 (octal)
octal numbers.
Wire Wire
Group 1 Group 3
dc Com 1(2) COM 1 COM 3 dc Com 3(2)
dc Com 1(2) COM 1 COM 3 dc Com 3(2)
IN 0 IN 16
+V dc 1 0 0
+V dc 3
IN 1 IN 17
1 1
IN 2 IN 18
2 2
IN 3 IN 19
3 3
IN 4 IN 20
4 4
IN 5 IN 21
5 5
IN 6 IN 22
6 6
IN 7 IN 23
Connector 7 7
IN 8 IN 24
Key 10 10
IN 9 IN 25
11 11
IN 10 IN 26
12 12
IN 11 IN 27
13 13
IN 12 IN 28
14 14
IN 13 IN 29
15 15
IN 14 IN 30
16 16
IN 15 IN 31
+V dc 2 17 17
+V dc 4
(2)
dc Com 2 COM 2 COM 4 dc Com 4(2)
dc Com 2(2) COM 2 COM 4 dc Com 4(2)
Wire Wire
Group 2 Group 4 (1)
SLC
PLC
(1) See decimal and octal coding information at the top of the page.
(2) The dc Com pins on the 1746-IB32 input module are isolated between the four groups and the two com pins in each group
are connected internally. To maintain group isolation provided by 32-point I/O modules, use a 1492 terminal block that
provides group isolation. Consult 1492 documentation or your Allen-Bradley Sales Office for additional information.
Wire Wire
Group 1 Group 3
+V dc 1(2) VDC 1 VDC 3 +V dc 3(2)
(2)
+V dc 1 VDC 1 VDC 3 +V dc 3(2)
IN 0 IN 16
dc Com 1 dc Com 3
0 0
IN 1 IN 17
1 1
IN 2 IN 18
2 2
IN 3 IN 19
3 3
IN 4 IN 20
4 4
IN 5 IN 21
5 5
IN 6 IN 22
6 6
IN 7 IN 23
Connector 7 7
IN 8 IN 24
Key
10 10
IN 9 IN 25
11 11
IN 10 IN 26
12 12
IN 11 IN 27
13 13
IN 12 IN 28
14 14
IN 13 IN 29
15 15
IN 14 IN 30
16 16
IN 15 IN 31
dc Com 2 17
dc Com 4
17
Wire Wire
Group 1 Group 2
+V dc 1(2)(3) VDC 1 VDC 2 +V dc 2(2)(3)
+V dc 1(2)(3) VDC 1 VDC 2 +V dc 2(2)(3)
OUT 0 OUT 16
CR CR
0 0
OUT 1 OUT 17
CR 1 1 CR
OUT 2 OUT 18
CR 2 2 CR
OUT 3 OUT 19
CR CR
3 3
OUT 4 OUT 20
4 4
OUT 5 OUT 21
5 5
OUT 6 OUT 22
6 6
OUT 7 OUT 23
Connector 7 7
Key OUT 8 OUT 24
CR CR
10 10
OUT 9 OUT 25
CR CR
11 11
OUT 10 OUT 26
CR CR
12 12
OUT 11 OUT 27
CR CR
13 13
OUT 12 OUT 28
14 14
OUT 13 OUT 29
15 15
OUT 14 OUT 30
16 16
OUT 15 OUT 31
17 17
Wire Wire
(2) Group 1 Group 2
+V dc 1 VDC 1 VDC 2 +V dc 2(2)
+V dc 1(2) VDC 1 VDC 2 +V dc 2(2)
OUT 0 OUT 16
CR CR
0 0
OUT 1 OUT 17
CR CR
1 1
OUT 2 OUT 18
CR 2 CR
2
OUT 3 OUT 19
CR CR
3 3
OUT 4 OUT 20
4 4
OUT 5 OUT 21
5 5
OUT 6 OUT 22
6 6
OUT 7 OUT 23
Connector 7 7
OUT 8 OUT 24
Key CR CR
10 10
OUT 9 OUT 25
CR CR
11 11
OUT 10 OUT 26
CR CR
12 12
OUT 11 OUT 27
CR CR
13 13
OUT 12 OUT 28
14 14
OUT 13 OUT 29
15 15
OUT 14 OUT 30
16 16
OUT 15 OUT 31
17 17
SLC (1)
PLC
´H'¶1-161-011$¨