Professional Documents
Culture Documents
Nominal data
Type K3G355-PG60-25
Motor M3G112-EA
Phase 1~
Nominal voltage VAC 230
Nominal voltage range VAC 200 .. 277
Frequency Hz 50/60
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
Technical features
Mass 22.5 kg
Size 355 mm
Motor size 112
Surface of rotor Coated in black
Material of electronics housing Die-cast aluminium
Material of impeller Aluminium sheet
Material of mounting plate Sheet steel, galvanised
Material of support bracket Steel, coated in black
Material of inlet nozzle Sheet steel, galvanised
Number of blades 5
Direction of rotation Clockwise, seen on rotor
Type of protection IP54
Insulation class "B"
Humidity (F) / environmental H1
protection class (H)
Max. permissible ambient motor +80 °C
temp. (transp./ storage)
Min. permissible ambient motor -40 °C
temp. (transp./storage)
Mounting position See key to the product drawing
Condensation drainage holes Rotor-side
Operation mode S1
Motor bearing Ball bearing
Technical features - Output 10 VDC, max. 10 mA
- Output 20 VDC, max. 50 mA
- Output for slave 0-10 V
- Tach output
- Input for sensor 0-10 V or 4-20 mA
- External 24 V input (programming)
- External release input
- Alarm relay
- Integrated PID controller
- Output limit
- Motor current limit
- PFC, active
- RS485 MODBUS RTU
- Soft start
- Control input 0-10 VDC / PWM
- Control interface with SELV potential safely disconnected from the mains
- Over-temperature protected electronics / motor
- Line undervoltage / phase failure detection
EMC interference immunity Acc. to EN 61000-6-2 (industrial environment)
EMC harmonics Acc. to EN 61000-3-2/3
EMC interference emission Acc. to EN 61000-6-4 (industrial environment)
Touch current acc. IEC 60990 <= 3.5 mA
(measuring network Fig. 4, TN
system)
Electrical connection Terminal box
Motor protection Thermal overload protector (TOP) wired internally
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
Product drawing
1 Installation position: Shaft horizontal (install the support struts only vertically as shown in the illustration!) or rotor on bottom; rotor
on top on request
2 Cable diameter min. 4 mm, max. 10 mm, tightening torque 4±0.6 Nm
3 Tightening torque 3.5±0.5 Nm
4 Inlet nozzle with pressure tap (k-factor: 148)
5 Attachment holes for inlet nozzle and FlowGrid (00400-2-2957 not included in scope of delivery)
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
Connection screen
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com
K3G355-PG60-25 EC centrifugal module - RadiPac
backward curved, single inlet
with support bracket
ρ = 1.15 kg/m³ ± 2 %
1000
4
4 Measurement: LU-174534-1
12
400 2
11
6
16
1
200 15 10
14
Measured values
U f n Ped I LpAin LwAin LwAout qV pfs qV pfs
V Hz min-1 W A dB(A) dB(A) dB(A) m3/h Pa cfm in. wg
1 230 50 2480 725 3.19 79 86 89 6445 0 3795 0.00
2 230 50 2480 1101 4.80 72 80 84 5160 400 3035 1.61
3 230 50 2480 1300 5.80 70 77 82 3770 750 2220 3.01
4 230 50 2480 1277 5.57 74 81 86 2620 950 1545 3.81
5 230 50 2100 425 1.87 75 82 85 5390 0 3175 0.00
6 230 50 2100 659 2.87 68 76 80 4350 285 2560 1.14
7 230 50 2100 786 3.43 66 73 78 3180 533 1870 2.14
8 230 50 2100 750 3.27 70 76 81 2195 675 1295 2.71
9 230 50 1700 225 0.99 69 76 79 4365 0 2570 0.00
10 230 50 1700 350 1.52 63 70 75 3520 187 2070 0.75
11 230 50 1700 417 1.82 61 68 72 2570 349 1515 1.40
12 230 50 1700 398 1.74 64 71 76 1780 442 1045 1.77
13 230 50 1300 101 0.44 62 70 73 3340 0 1965 0.00
14 230 50 1300 156 0.68 56 64 68 2690 109 1585 0.44
15 230 50 1300 187 0.81 54 61 66 1965 204 1160 0.82
16 230 50 1300 178 0.78 57 64 69 1360 259 800 1.04
U = Supply voltage · f = Frequency · n = Speed (rpm) · Ped = Power input · I = Current draw · LpAin = Sound pressure level inlet side · LwAin = Sound power level inlet side · LwAout = Sound power level outlet side
qV = Air flow · pfs = Pressure increase
ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · info1@de.ebmpapst.com · www.ebmpapst.com