Professional Documents
Culture Documents
TP1 Ccna
TP1 Ccna
192.168.0.0 26 255.255.255.192
192.168.0.64 26 255.255.255.192
192.168.0.128 26 255.255.255.192
192.168.0.192 26 255.255.255.192
Routeur
System Bootstrap, Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 2010 by cisco Systems, Inc.
Total memory size = 512 MB - On-board = 512 MB, DIMM0 = 0 MB
CISCO1941/K9 platform with 524288 Kbytes of main memory
Main memory is configured to 64/-1(On-board/DIMM0) bit mode with ECC disabled
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Router>enable
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#enable secret Class123
Router(config)#line console 0
Router(config-line)#password Cisco123
Router(config-line)#login
Router(config-line)#
Router#
%SYS-5-CONFIG_I: Configured from console by console
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#hostname Routeur-Client
Routeur-Client(config)#int g0/0
Routeur-Client(config-if)#ip add 192.168.0.1 255.255.255.192
Routeur-Client(config-if)#no shutdown
Routeur-Client(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up
LAN-A
C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(25r)FX, RELEASE SOFTWARE
(fc4)
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
2960-24TT starting...
Base ethernet MAC Address: 00D0.58EA.D1BD
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 2 files, 0 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32514048
flashfs[0]: Bytes used: 4415999
flashfs[0]: Bytes available: 28098049
flashfs[0]: flashfs fsck took 1 seconds.
...done Initializing Flash.
Loading "flash:/c2960-lanbase-mz.122-25.FX.bin"...
######################### [OK]
Restricted Rights Legend
Cisco WS-C2960-24TT (RC32300) processor (revision C0) with 21039K bytes of memory.
Switch>enable
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#int vlan 1
Switch(config-if)#ip add 192.168.0.2 255.255.255.192
Switch(config-if)#no shutdown
Switch(config-if)#
%LINK-5-CHANGED: Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up
Switch(config-if)#exit
Switch(config)#ip de
Switch(config)#ip default-gateway 192.168.0.1
Switch(config)#do wr
Building configuration...
[OK]
Switch(config)#hostname LAN-A
LAN-A(config)#
Password:
Routeur-Client>enable
Password:
Password:
Routeur-Client#copy run start
Destination filename [startup-config]?
Building configuration...
[OK]
Routeur-Client#int g0/1
^
% Invalid input detected at '^' marker.
Routeur-Client#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Routeur-Client(config)#int g0/1
Routeur-Client(config-if)#ip add 192.168.0.65 255.255.255.192
Routeur-Client(config-if)#?
arp Set arp type (arpa, probe, snap) or timeout
bandwidth Set bandwidth informational parameter
cdp CDP interface subcommands
channel-group Add this interface to an Etherchannel group
crypto Encryption/Decryption commands
custom-queue-list Assign a custom queue list to an interface
delay Specify interface throughput delay
description Interface specific description
duplex Configure duplex operation.
exit Exit from interface configuration mode
fair-queue Enable Fair Queuing on an Interface
hold-queue Set hold queue depth
ip Interface Internet Protocol config commands
ipv6 IPv6 interface subcommands
lldp LLDP interface subcommands
mac-address Manually set interface MAC address
mtu Set the interface Maximum Transmission Unit (MTU)
no Negate a command or set its defaults
pppoe pppoe interface subcommands
pppoe-client pppoe client
priority-group Assign a priority group to an interface
service-policy Configure QoS Service Policy
Routeur-Client(config-if)#no shutdown
Routeur-Client(config-if)#
%LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to up