Professional Documents
Culture Documents
AC TECHNICAL REGULATIONS
v1.4
4 August 2022
DocuSign Envelope ID: 68C279D0-A5C4-4C8A-8F43-B867CEABC977
Contents
1 Introduction 2
2 Language 3
3 Reference frames and units 4
4 Component limits and modifications 5
5 Measurement 11
6 Non‐compliance with the Class Rules 13
7 Interpretation and amendment 16
8 Meteorological and oceanographic data 19
9 Shrouding 20
10 Reconnaissance 21
11 Definitions 29
12 Agreement 46
1 Introduction
1.1 This document, the AC Technical Regulations, defines rules that govern yachts sailed by Competitors in
the 37th America’s Cup. It also includes rules relating to shrouding, Competitors’ chase boats, weather
collection and reconnaissance.
1.2 The AC Technical Regulations shall be read and interpreted in conjunction with the AC75 Class Rule and
AC40 Class Rule.
1.3 Rules that classify or provide interpretation within the AC Technical Regulations, for instance the “Lan‐
guage”, “Reference frames and units” and “Definitions” sections, apply to all documents that comprise
the Class Rules.
1.4 The AC75 Class Rule, the AC40 Class Rule and the AC Technical Regulations shall be in force from their
first publication in non‐draft form (without the word ‘Draft’ on the cover), and Competitors shall comply
with them until the completion of the final race of the 37th America’s Cup.
1.5 The AC75 Class Rule, the AC40 Class Rule and the AC Technical Regulations include:
(a) rules that govern an AC75 Class Yacht and an AC40 Class Yacht, including how they are constructed
and how they are raced, which shall apply during measurement and when racing, unless stated
otherwise; and
(b) rules that govern:
(i) procedures of measurement, declaration, interpretation, amendment;
(ii) limits on quantities, manufacture, modification and testing of components;
(iii) weather collection, shrouding, reconnaissance; and
(iv) other matters that are not separately addressed in the Protocol;
which shall apply at all times unless stated otherwise.
The applicable time‐period over which a Rule is in force shall be indicated by the context, but if there is
any doubt, shall apply at all times.
2 Language
2.2 Within the Class Rules, the word “Rule” is a reference to a rule of the Class Rules, and unless specified
otherwise is a reference to a rule within the same document.
2.3 Where words or phrases are printed in bold type their meaning is defined in Rule 11 of the AC Technical
Regulations. Bold terms may be be used in modified grammatical forms, in which case any modification
to the term relates to a corresponding modification to the definition.
2.4 In some document viewers, the definition of terms in bold may be seen as a tooltip. Although these tooltips
are intended to provide the correct and full definitions, they should not be relied upon; the text printed in
Rule 11 of the AC Technical Regulations is the only authoritative source.
2.5 Where words or phrases are printed in italic type their meaning has a local definition that only applies
within that section of the Class Rules.
2.6 The interpretation of words not defined in bold shall be made with reference to The Oxford English Dictio‐
nary, as it exists online at www.oed.com (or such later official website of the Oxford English Dictionary).
In interpretation, the Rules Committee shall determine the most appropriate definition of a word within
the Oxford English Dictionary, or if no appropriate definition is found, from another authoritative source.
2.7 The words “can” and “may” are permissive, but the permission is restricted when followed by the words
“not”, “only” or similar. The words “will”, “must”, and “shall” are mandatory.
2.8 The word “or” is used as an “inclusive or”, meaning the same as “and/or”, except where it is clearly an
“exclusive or” from the grammar or context, such as when:
(a) it is preceded by the word “either”; or
(b) the options separated by the “or” are logically exclusive.
2.9 Where the word “significant” is used, it means “non‐negligible”, or “sufficiently great or important to be
consequential or influential”. As an exception, the phrase “significant figure” has its usual mathematical
meaning.
2.10 The phrase “for the avoidance of doubt” indicates that the subject that follows is already controlled by a
more general Rule, but the specific Rule is included to remove any potential uncertainty in interpretation.
3.1 The Measurement Waterline Plane, MWP, is defined as the horizontal reference plane of the yacht.
3.2 The Longitudinal Centre Plane, LCP, is defined as a vertical reference plane, orthogonal to MWP.
3.3 The Transom Reference Plane, TRP, is defined as the vertical reference plane orthogonal to MWP and LCP.
3.4 The reference planes MWP, LCP and TRP are fixed to the yacht, translating and rotating as the yacht moves
in space.
3.5 Except where otherwise specified, terms such as “above”, “below”, “up”, “down”, “forward” and “aft” refer
to directions or relative positions aligned to the xyz‐axes in the yacht‐fixed reference frame, where:
3.6 The mast and mainsail shall be measured in a mast‐fixed reference frame, where:
(a) the origin is at MRP;
(b) u is an axis perpendicular to the shear web of the mast tube, positive towards the front of the yacht;
(c) v is an axis perpendicular to u and w, positive towards port; and
(d) w is an axis parallel to the intersection of the shear web of the mast tube with the mast centre
plane, positive up.
3.7 The following tolerances shall be applied to all dimensions specified in the Class Rules:
(a) where a measurement is required to be a specific value:
(i) where decimal places for a unit are given, the measurement shall be accurate to the least
significant figure indicated. For example, if a Rule states that a length must be 5.0 m, that
length must be at least 4.95 m and less than 5.05 m;
(ii) where decimal places for a unit are not given, the measurement shall be accurate to within 1%
of the figure indicated. For example, if a Rule states that a component must weigh 1000 kg,
that component must weigh between 990 kg and 1010 kg inclusive; and
(b) where a measurement is required to be “at least”, “at most”, “no less than”, “no greater than”,
“a minimum”, “a maximum”, “between”, “within a range”, or other similar wording, no tolerance
beyond that limit or outside that range is permitted, but the permitted measurement is inclusive of
the limit value. For example, if a Rule states that a length must be no more than 5 m, that length
must be no more than 5.000000 m.
3.8 Pressures in the Class Rules refer to gauge pressures unless otherwise specified.
4.1 Key components of AC75 Class Yachts and LEQ12 yachts are restricted in quantity and degree of mod‐
ification. Any listed component that serves or partly serves the purpose of a listed component shall be
counted, where:
(a) a component launched on an AC75 Class Yacht or a surrogate yacht shall be treated as an AC75
Class Yacht component; and
(b) a component launched on an LEQ12 yacht shall be treated as an LEQ12 yacht component.
4.2 As an exception to Rule 4.1, in class AC40 Class Yacht supplied components are not counted in the quantity
limits imposed by these Rules if they are installed on an in class AC40 Class Yacht hull. However, if:
(a) an AC40 Class Yacht supplied component is modified such that it is no longer in class; or
(b) installed on any yacht except an in class AC40 Class Yacht hull;
and launched, it is then treated as a new LEQ12 yacht component.
4.3 For an AC75 Class Yacht, the components in the table below are restricted in quantity and degree of
modification.
Legacy New
Legacy New Total
Component immutable immutable
quantity quantity quantity
portion portion
Hull surfaces 1 87.5% area* 1 87.5% area 2
Foil arm stocks 4 See Rule 4.12 4 100% mass 4
Foil wings 2 100% mass 3† 80% mass 5
Foil flaps 2 100% mass 5‡ 80% mass 7
Rudders 2 80% mass 2 80% mass 4
Mast tubes 1 See Rule 4.13 2 80% mass 3
Mainsail skins 8 85% area 12 85% area 20
Jib skins 10 85% area 15 85% area 25
*See Rule 4.9. †See Rule 4.10. ‡See Rule 4.11.
4.4 For an LEQ12 yacht, all components launched after 17th March 2021 shall be counted in the applicable
limits. The components in the table below are restricted in quantity and degree of modification.
4.5 The values in the column “Legacy quantity” of Rule 4.3 are the maximum number of legacy components
that a Competitor may launch. A legacy component:
(a) is a component that was declared by a Competitor of AC36, which need not be the same Competitor
that is using it as a legacy component in AC37;
(b) in the case of a foil flap, is a pair of AC36 foil flaps, since they were defined as separate items for
each side of a foil wing in AC36;
(c) must have a Version A for AC37 that exactly matches a configuration in which that component was
declared to the Measurement Committee during AC36, where:
(i) such configuration need not be the configuration in which that component was first launched
during AC36, nor the final configuration of that component in AC36;
(ii) such configuration need not have been launched during AC36 providing it was declared to
the Measurement Committee according to the component declaration procedures of AC36;
and
(iii) the Competitor launching a legacy component in AC37 must provide a declaration to the
Measurement Committee that the declared configuration matches a declared AC36 config‐
uration. That declaration must include the date that the specific configuration was declared
during AC36, and the relevant documentation such as IGES files or drawings supplied to the
AC36 Measurement Committee at that time. If the component has transferred ownership,
this declaration must be supported by the AC36 Competitor that originally declared the com‐
ponent; and
(d) once declared in AC37 in accordance with Rule 4.23, is treated in the same way as a new AC37
component in terms of change and repair allowances described in this Rule subject to the “Legacy
immutable portions” tabulated in Rule 4.3.
4.6 The values in the column “New quantity” of Rules 4.3 and 4.4 are the maximum number of new compo‐
nents that a Competitor may launch. A new component need not be newly built; it could be a modified
or unmodified component that was previously declared in AC36 or AC37 if that component cannot be
declared as a legacy component, or if a Competitor chooses not to declare it as a legacy component.
4.7 The values in the column “Total quantity” of Rule 4.3 are the maximum number of components, whether
new or legacy, that a Competitor may launch.
4.8 The quantities tabulated in Rules 4.3 and 4.4 are limits applying per Competitor, not per yacht.
4.9 The hull lower surface of a legacy hull cannot be modified; changes to the hull surface of a legacy hull
shall be confined to the deck.
4.10 The second and third new AC75 Class Yacht foil wings declared by a Competitor must have an identical
Version A design to their first declared new AC75 Class Yacht foil wing. Those second and third new foil
wings must also retain the same immutable portion as the first declared new foil wing throughout AC37.
4.11 The five new AC75 Class Yacht foil flaps shall have between them a maximum of two distinct Version A
designs, and the new foil flaps corresponding each of those two Version A designs shall retain the same
immutable portions as the first declared of each design throughout AC37.
4.12 The AC37 Version A of a legacy foil arm stock shall match the AC36 foil arm stock specification. The only
modifications that may be made to a legacy foil arm stock are to:
(a) update it to match the AC37 foil arm stock specification detailed in the “Foil arms” section of the
AC75 Class Rule; or
(b) to return it to match the AC36 foil arm stock specification.
4.13 Legacy mast tubes shall only be modified from their AC37 Version A of the component within:
(a) the mast lower zone; and
4.14 New Competitors may substitute up to 4 legacy mainsail skins and 5 legacy jib skins for equivalent replicas
of legacy sail skins, provided that:
(a) the New Competitor owns a legacy hull with AC36 sail number 1, 2, 3 or 4 (the paired hull);
(b) each new replica sail skin has an identical blank design to a version of a sail skin that was:
(i) launched by a Competitor of AC36; and
(ii) first hoisted on a mast stepped on the paired hull;
(c) each replica skin is only ever hoisted on a mast stepped on the paired hull.
4.15 The following new AC75 Class Yacht components may not be installed on a legacy AC75 Class Yacht hull:
(a) foil wings;
(b) foil flaps;
(c) rudders;
4.16 A component shall be counted in the applicable limits regardless of whether that component satisfies
the specific Rules controlling its parameters in the Class Rules. In the event that a test component cannot
readily be identified as a specific component type, a classification of type and quantity shall be determined
by the Rules Committee by following the interpretation process detailed in Rule 7.5, where:
(a) components shall be classified according to resemblance in form or function to AC75 Class Yacht
components, whatever their scale;
(b) test components shall be counted even if they only resemble one aspect of an AC75 Class Yacht
component, without matching the overall functionality; and
(c) in an extreme case, a single test component may be ruled as comprising multiple declared com‐
ponents if it is effectively serving the purpose of multiple components, depending on its method
of installation in a yacht. For example, a double‐ended rudder that could be installed either way
up, with only one half of the component tested at a time, could be ruled as two declared rudders.
However, a conventional rudder that could be installed at different extensions, or an asymmetric
foil wing with different design concepts on either side of its connection to a foil arm shall be treated
as a single component.
4.17 Competitors must track listed components and versions of those components in a spreadsheet with the
following columns:
(e) Area: the controlled surface area of the component, for components whose change percentage is
controlled by area;
(f) Comment: text briefly describing the component or type of modification.
Each row shall represent a version of a specific component. The rows shall be grouped by the component
ID, where the first row for each component must be the declared Version A of that component.
4.18 The ID for a new AC75 Class Yacht component shall be distinct from any ID of the same AC75 Class Yacht
component type launched by the same Competitor in AC36, such that any component from either AC36
or AC37 can be uniquely identified by the combination of the Competitor that launched it and the com‐
ponent’s ID.
4.19 A new AC75 Class Yacht hull’s ID or hull number shall be allocated by the Measurement Committee when
it is launched. Competitors shall inform the Measurement Committee when this occurs, and hull numbers
will be allocated sequentially, starting with 9, except that culturally objectionable numbers may be skipped
at the discretion of the Measurement Committee.
4.20 Hull numbers for AC40 Class Yachts shall be allocated sequentially by the manufacturer, starting at 1.
4.21 Version A of a component is the version from which changes to that component are compared and mea‐
sured. It may be the configuration in which the component was launched, or some other hypothetical
configuration.
4.22 Version A of new AC75 Class Yacht components must comply with the relevant rules for that component
type.
4.23 Except when restoring a component to a previously declared version, a new version of a component must
be declared:
(a) for components whose change percentage is controlled by mass, whenever any change is made to
that component, even if there are no changes to its blueprint; and
(b) for components whose change percentage is controlled by area, whenever that component changes
with respect to its blueprint.
4.24 Competitors may declare components and component versions by emailing an updated copy of the
Rule 4.17 spreadsheet to the Measurement Committee. If a component or version of a component has
not previously been declared, it must be declared within 48 hours of the component being launched.
4.25 For components whose change percentage is controlled by mass, the mass for the first launched version
of a component must be determined by weighing that component. For other versions, a calculated mass
can be declared based on the changes made to a launched component, or on a hypothetical configuration,
but the Measurement Committee may require a component to be weighed at any time.
4.26 The material substance of the portion of the component indicated in Rule 4.3 must remain immutable
through the life of the component, whereby:
(a) at least the indicated percentage of the mass or surface area of every version of the component
must remain unmodified from version A of the component;
(b) a common portion of at least the indicated percentage of the mass or surface area of version A of
the component must remain unmodified and must match all declared versions of the component;
and
(c) if Version A does not represent a physical version of a component, the immutable portion of the
component must be referenced to material that would be present if the component was modified
to Version A.
4.27 For hulls, foil wings, foil flaps, rudders and mast tubes:
(a) the immutable portion of the component may comprise several disjoint regions divided by modi‐
fied material, but those separate regions must remain in an identical position and orientation with
respect to each other through the life of the component;
(b) the blueprint of all versions of the component except Version A must include a surface entity or en‐
tities that enclose (for mass) or overlay (for surface area) regions that satisfy Rules 4.26 (a) and 4.26
(b); and
(c) all blueprints for a component must be aligned with respect to these surface entities such that they
overlay exactly across all versions.
4.29 As an exception to Rule 4.26, material within a component that has been:
(a) replaced with identical or equivalent material as part of a repair permitted by Rule 4.30;
4.30 It is permitted to repair or replace a new or legacy hull surface, foil arm stock, foil wing, foil flap, rudder
or mast tube to restore it to an AC37 declared configuration, where:
(a) the material substance need not be the same material as in the declared component, providing that
except where modification is permitted, surface geometry is identical and the material specification
is equivalent to the satisfaction of the Measurement Committee; for example:
(i) dry fibre may be substituted for an equivalent pre‐preg fibre;
(ii) two plies of 150 g/m2 may be substituted for one ply of 300 g/m2 ; or
(iii) fibre may be substituted for fibre of a different modulus, provided that there is no significant
change in the component’s stiffness or behaviour under load;
(b) any construction forming part of the repair or replacement is built or prepared only once that com‐
ponent has been taken out of service, and that component is not installed with the yacht afloat again
until that repair is complete;
(c) the restriction in Rule 4.30 (b) does not apply to the construction of:
(i) flat monolithic plate which has a uniform construction across the plate;
(ii) flat sandwich panel which has a uniform construction across the panel; or
(iii) round tubes of uniform construction and cross‐sectional shape;
(e) a Competitor alone shall decide whether to repair or replace a component, and no evidence of
damage is required.
4.31 If a hull, foil arm stock, foil wing, foil flap, rudder or mast tube is unintentionally damaged and a repair
or replacement in accordance with Rule 4.30 cannot be completed in time for the Competitor’s next race,
the Measurement Committee may permit a temporary repair using alternative materials and construction
methods, providing that:
(a) the repair is no larger than required;
(f) the temporary repair is replaced by a repair in accordance with Rule 4.30 as soon as possible.
5 Measurement
5.1 The Measurement Committee may place measurement marks or seals on yacht components during con‐
struction or upon their completion. These marks or seals may include, but are not limited to, reference
screws, punch marks, measurers’ signatures, cable ties and stickers, on components or component tool‐
ing. Competitors shall permit inspections, allow such marks to be placed, and shall not move, remove or
alter any such marks or seals without the express consent of the Measurement Committee.
5.3 Except where specified, it is not the responsibility of a Competitor to provide categorical proof of compli‐
ance with the Class Rules. Where proof by inspection or measurement is impractical, the Measurement
Committee shall rely on interviews, affidavits and reference documentation. However, it always remains
the responsibility of a Competitor to ensure that their yacht complies with the Class Rules, including in
areas that cannot be easily measured.
5.4 Leading up to events, the Measurement Committee will publish dates of measurement periods, during
which Competitors may present their yachts for measurement. The Measurement Committee will inspect
the yachts for compliance with the Class Rules, and Competitors shall provide whatever assistance is
reasonably requested by the Measurement Committee to facilitate this process.
5.5 The Measurement Committee shall use its own equipment for measuring a Competitor’s yacht, except
that a Competitor’s equipment may be used at the discretion of the Measurement Committee if it is
calibrated against the Measurement Committee’s equipment and sealed to their satisfaction.
5.6 When weighing components of a yacht, Competitors shall be permitted to dry any water on the surface
of those components and replace wet rigging with equivalent dry rigging. The Measurement Committee
shall make reasonable allowances for wet sail weights.
5.7 Where specific tolerances for component measurement are not given in the Class Rules, the Measure‐
ment Committee may make an allowance for unintended distortion of a component during manufacture
when checking the shape of such a component against its blueprint.
5.8 The Measurement Committee shall, at times they choose during AC37, make spot checks of compliance
with component declarations by requiring a Competitor to declare to them what component versions they
sailed with on their last sailing day. The Measurement Committee may also request, and Competitors shall
supply, blueprints corresponding to those component versions and declared SHAs.
5.9 Except as otherwise specified, Competitors are not required to routinely supply construction drawings of
declared components. However, if the Measurement Committee have any doubt as to the compliance of
a component they may request such drawings, which shall then be supplied by the Competitor.
5.10 Competitors shall inform the Measurement Committee immediately if they make any changes or repairs
to the yacht that could affect her measurement certificate or her compliance with the Class Rules.
5.11 The Measurement Committee reserve the right to re‐measure or inspect any aspect of a yacht at any
time, before or after sailing, and may publish procedures for regular measurement inspections.
5.13 During training or racing, Competitors shall permit the Measurement Committee to install small video
cameras onboard their yachts to assist the Measurement Committee in determining compliance, where:
(a) the mass of these cameras shall not be included in the measurement mass of the yacht;
(b) the Measurement Committee shall where possible locate the cameras in locations that minimise
any increase in aerodynamic drag, providing they are still able to capture the details required; and
(c) Competitors shall not adjust nor deliberately obstruct the view from these cameras.
6.1 After a measurement certificate has been issued for an event or AC75 event stage, if the Measurement
Committee:
(a) determines that it has issued a measurement certificate in error, and that a yacht is non‐compliant
with the Class Rules;
(b) determines that a new interpretation issued by the Rules Committee renders a yacht non‐compliant
with the Class Rules;
(c) determines that a yacht is non‐compliant with the Class Rules as a result of a query of compliance
by a Competitor detailed by Rule 6.7; or
(d) is informed by the Rules Committee that a yacht is non‐compliant with the Class Rules following
the process described by Rule 5.12 (b);
they shall notify the Regatta Director, notify all Competitors and follow the process detailed in Rule 6.2.
No penalty shall be applied relating to races sailed when non‐compliant unless a condition within Rule 6.3
is also found to apply.
6.2 If a Competitor’s yacht is found to be non‐compliant with the Class Rules according to Rule 6.1, a deter‐
mination of the Competitor’s ability to rectify the non‐compliance in time for the next race shall be made
by the Regatta Director in consultation with the Measurement Committee, and:
(a) if they find that the Competitor is able to rectify the non‐compliance, and the yacht can be re‐
inspected before the next race, the Measurement Committee shall withdraw the yacht’s measure‐
ment certificate immediately;
(b) otherwise, the Regatta Director may grant a grace period which shall end no later than:
(i) the end of the following day, if the yacht has a race on the following day that is scheduled to
start within 24 hours of the current time; otherwise
(ii) the end of the current day;
the current time being the time at which the Measurement Committee notifies the Regatta Direc‐
tor and all Competitors of the non‐compliance. The Measurement Committee shall withdraw the
yacht’s measurement certificate at the expiry of any grace period.
6.3 After a measurement certificate has been issued for an event or AC75 event stage, if the Measurement
Committee determines that:
(a) a yacht has been modified without the approval of the Measurement Committee and:
6.4 If a yacht’s measurement certificate has been withdrawn according to Rule 6.3, and the yacht has raced in
a non‐compliant configuration, the Measurement Committee shall notify the Jury, the Regatta Director
and all Competitors with details of:
6.5 On receiving notification from the Measurement Committee according to Rule 6.4, the Regatta Director
shall review the non‐compliance, requesting further investigation if necessary. As a result, if the Regatta
Director determines that the non‐compliance is:
(a) unintentional, and unlikely to have impacted the outcome of a race, the Jury, in consultation with
the Regatta Director may impose a fine on the Competitor;
(b) intentional, or could have impacted the outcome of a race, the Jury, in consultation with the Regatta
Director may disqualify the yacht from:
(i) the last race in which the yacht competed if the yacht competed in only one race while non‐
compliant; or
(ii) the last two races in which the yacht competed whilst non‐compliant.
6.6 A Competitor whose measurement certificate has been withdrawn must rectify the non‐compliance,
present their yacht for re‐measurement and receive a new measurement certificate prior to being eligible
for any further racing in the current event or AC75 event stage.
6.7 During an event, a Competitor may query the compliance of another Competitor’s yacht by sending an
email to the Measurement Committee that details the potential areas of non‐compliance. The Measure‐
ment Committee shall investigate and:
(a) if the Measurement Committee finds that the yacht complies with the Class Rules, they shall notify
the Regatta Director and all Competitors with details of the investigation and an explanation as to
why they are satisfied that the yacht continues to comply; or
(b) if the Measurement Committee finds that the yacht does not comply with the Class Rules, they
shall proceed according to Rule 6.1.
6.8 The total number of measurement compliance queries that may be made by each Competitor shall be
limited as follows:
(a) two queries in each Preliminary Regatta;
(b) three queries in the America’s Cup Challenger Selection Series; and
6.9 If a yacht is unintentionally damaged whilst racing to the extent that she is no longer compliant with the
Class Rules, or no longer matches the configuration specified in her measurement certificate, the Mea‐
surement Committee shall notify the Regatta Director with details of:
(a) the non‐compliance;
(b) any races the yacht may have raced in whilst non‐compliant; and
(c) the potential performance implications of the non‐compliance.
If the Regatta Director in consultation with the Measurement Committee determine that the non‐
compliance is unlikely to have increased the performance of the yacht, no penalty shall be applied relating
to races already sailed; otherwise, the Regatta Director shall inform the Jury who in consultation with the
Regatta Director may impose a penalty at their discretion.
6.10 After a yacht has been damaged as described by Rule 6.9, if:
(a) it is not possible for repairs to be made to restore the yacht to a compliant condition in time for her
next race (after accounting for any changes permitted by a substitution schedule); and
(b) the Measurement Committee determines that any damage or subsequent temporary repair could
not positively impact the performance of the yacht;
the yacht may be granted an exemption to the specific Class Rules or parts of her measurement certificate
that she cannot comply with, and permitted to race.
6.11 The decision to grant an exemption described in Rule 6.10 shall be made by:
(a) the Regatta Director in consultation with the Measurement Committee, for any races that are
scheduled on the same sailing day in which the damage occurred; and
(b) the Jury, in consultation with the Regatta Director and the Measurement Committee, for any races
on subsequent sailing days. In this case, prior to making their decision, the Jury:
(i) may decide to provide details of the damage, repair and substitution options to other Com‐
petitors affected by their decision so that those Competitors have an opportunity to provide
relevant technical feedback; and
(ii) must be entirely satisfied that Rules 6.10 (a) and 6.10 (b) apply;
prior to granting such an exemption.
In any case in which an exemption is granted, the yacht shall be restored to a compliant condition as soon
as possible.
7.2 The AC40 Class Rule may be amended at any time by the Defender.
(a) according to the same conditions that apply to the AC75 Class Rule in Rule 7.1;
(b) for Rule 4, “Component limits and modifications”, by COR/D at any time; and
(c) for Rule 10, “Reconnaissance”, by COR/D at any time.
7.4 If the date for the first race of the 37th America’s Cup Match is announced to be at any time before 1st
January 2024 or after 1st September 2024, any dates within the AC75 Class Rule and AC Technical Regula‐
tions may be amended by COR/D during the 10 working days following such an announcement. This Rule
applies to both an original announcement of the date, and to any subsequent announcement of a change
in date.
7.5 A Competitor may submit a Rule Enquiry regarding the AC75 Class Rule or AC Technical Regulations to
the Rules Committee in the form of:
(a) an interpretation request;
(b) may include references to relevant paragraph numbers within the Class Rules, indicated as “75‐X.X”,
“40‐X.X” or “TR‐X.X”, but should not include formal excerpts of those Rules except where used di‐
rectly in the context of the question;
(c) shall be in a form that can be directly and immediately forwarded to all Competitors without the
need for further editing; and
(d) shall be submitted by email to the Rules Committee or if advised, to a specific Rule Enquiry email
address.
A mechanism may be implemented whereby these requests are forwarded automatically to Competitors
as soon as they are received; otherwise, the Rules Committee shall forward them as soon as possible. In
either case, the email subject line of the forwarded request shall include a sequential Rule Enquiry number.
7.7 The Rules Committee can also initiate a Rule Enquiry, providing that it does not reveal a design character‐
istic that might not have been considered by all Competitors.
(a) The Rules Committee shall immediately publish the Enquiry, if not automatically distributed.
(b) Within 4 working days, Competitors may reply to the Rules Committee to:
(i) consent to a draft amendment;
(ii) supply comments on the interpretation and/or amendment proposal; or
(iii) propose an alternative amendment wording.
(c) Within 4 working days of the feedback from Competitors being due:
(i) If there is sufficient consent to implement a proposed amendment according to the condi‐
tions of Rules 7.1, 7.2 and 7.3, then the Rules Committee shall amend the relevant docu‐
ments of the Class Rules, publish the new version, and mark the Rule Enquiry as closed.
(ii) Else if the Rules Committee consider that there is the possibility that the issue can be re‐
solved by an amendment, then they shall propose or revise a draft amendment, this option
being preferred to an interpretation.
(iii) Else if there was no interpretation question as part of Rule Enquiry, the Rules Committee
shall mark the Rule Enquiry as closed, there being no agreement on a proposed amendment.
(iv) Else if at least one interpretation draft has previously been circulated and the Rules Com‐
mittee, having reviewed all feedback, is satisfied that the interpretation cannot be improved
then they shall publish the previously circulated interpretation draft as a final interpretation
and mark the Rule Enquiry as closed.
(v) Else the Rules Committee shall propose or revise a draft interpretation response, subject to
Rule 7.9.
(d) If not closed, the process shall then return to step 7.8 (b).
7.9 At the step described by Rule 7.8 (c) (v), if the Rules Committee, after considering the feedback from
Competitors, determine an interpretation request included in the Rule Enquiry to be unreasonably long,
or to cover an unreasonably large number or matrix of possible scenarios, they may withdraw the request
and request the original Competitor to re‐submit the Rule Enquiry with an interpretation request that
limits the scope of the question to those elements which better clarify ambiguity in the Class Rules.
7.10 The Rule Enquiry, all Competitor responses, and all draft and final responses by the Rules Committee shall
be published by the Rules Committee to the Official Noticeboard (as defined in the protocol). Competitor
responses will not be published until either all responses have been received or the deadline detailed by
Rule 7.8 (b) has passed, whichever is earlier. The Rule Enquiry and responses from the Rules Committee
shall be published as soon as they are issued.
7.11 Rule Enquiries and response documents from Competitors shall be published in the form in which they are
received without any additional information indicating who they are from. Competitors may anonymise
their submission.
7.12 The Rules Committee may, at their discretion, shorten any of the times allowed in Rule 7.8, particularly
leading up to events.
7.13 With the agreement of the Competitor seeking the amendment or interpretation, the Rules Committee
may lengthen any of the times allowed in Rule 7.8.
(b) where wording is ambiguous, the most reasonable and natural interpretation of the written words
within the context of any other relevant Class Rules shall be taken;
(c) if a part of the Class Rules, or the understanding of it created by the application of clause 7.14 (b),
is found to directly contradict another part, a part that refers to more detail shall take precedence
over a part that is more general; and
(d) finally, if there remains ambiguity or contradiction as to whether a particular feature is permitted,
and that ambiguity or contradiction cannot be resolved by application of the above clauses, an in‐
terpretation shall be permissive.
7.15 Draft responses from the Rules Committee shall not constitute a ruling of any form. Whilst Competitors
may comment on these drafts, they are inadmissible as evidence of any interpretation of the Class Rules
unless published as final.
7.16 The Rules Committee may seek the advice of independent experts, including members of the Measure‐
ment Committee, when considering an interpretation.
7.17 Competitors shall not conduct any private correspondence with the Rules Committee regarding any Rule,
interpretation or amendment. Correspondence shall only be in the form described by Rule 7.5, or within
a group forum which all Competitors are invited to attend.
7.18 Advice or opinions on the meaning of a Rule, from a member of the Measurement Committee or Rules
Committee, are not binding except through an interpretation.
7.19 Once an interpretation has been issued as final, it cannot be modified without the explicit agreement of
all Competitors.
7.20 Interpretations that relate specifically to wording within the Class Rules that has since been amended no
longer apply.
7.21 Separately to the interpretation and amendment process described in the above rules, Competitors may
request clarification of the construction or operational requirements of specified or supplied components
including foil arm stocks, mast tube specifications, supplied rigging and the FCS. Requests for clarification
should be made to the Rules Committee who, after consultation with the designers of those parts, will
issue a clarification notice to all Competitors.
8.1 After the announcement of the Match venue, Competitors shall only collect weather, wind, sea state or
sea current instrument data relevant to the Match venue:
(a) from devices that measure weather, wind, sea state or sea current within 100 mm of a sensor
mounted on any of a Competitor’s eligible yachts;
(b) from a chase boat that is supporting one of that Competitor’s eligible yachts, limited to two chase
boats per yacht, which must be the primary chase boats for that yacht; and
(c) as permitted by the Protocol.
8.2 With reference to Rule 8.1, Competitor’s yachts are eligible provided that:
(a) Competitors shall be limited to a maximum of two eligible yachts per day; and
(b) during an event, whenever any of a Competitor’s yachts are within their racing period, the only
eligible yachts for that Competitor shall be those yachts that are currently within their racing period,
where a racing period for a yacht is the period that:
(i) begins 45 minutes before the warning signal of that yacht’s race; and
(ii) ends at the completion of that race.
(i) travel directly to and from the Competitor’s shore base for the purpose of refuelling or main‐
tenance; or
(ii) remain at a Competitor’s shore base.
8.4 When at the Match venue, after it has been announced, wind measuring devices shall only be installed
on Competitors’ chase boats if:
(a) they are supporting their yacht;
(b) the wind measuring devices are covered rendering them inoperable; or
(c) the Regatta Director has given permission for their use.
9 Shrouding
9.1 No component or part of the yacht shall be covered for the purpose of hiding it from reconnaissance once
it has been launched, or when it is about to be launched (i.e. prepared for being lifted into the water),
unless:
(a) it is not being used for sailing operations on that day; or
(b) the item providing cover (the ‘cover‘) is a part of the yacht that satisfies the AC75 Class Rules, and
remains in the same position whilst sailing.
9.2 Any temporary cover used for physical or sun protection during sailing operations shall be immediately
removed at the request of reconnaissance teams. The Measurement Committee may remove the right
of a Competitor to use any such covers if they believe the covers are being used to hinder the role of
reconnaissance units.
10 Reconnaissance
10.1 Applicability
(a) This section sets out the regulations governing a Joint Competitor Reconnaissance Programme.
(b) The Joint Reconnaissance Programme shall be in place from the first official publication of these AC
Technical Regulations until two months before the first race of the Final Preliminary Regatta.
(c) At an Initial Preliminary Regatta, during the time period starting at 08:00 seven days before the
programmed start of the first race and ending at 23:59 on the day of the final race (in the local time
zone of the regatta), any sailing by a Competitor in an in class AC40 Class Yacht is not required to
be notified, observed or declared as a Sailing Session.
(d) An in class AC40 Class Yacht is one whose components restricted by Rule 4.4 are all in class.
(e) The italicised terms within Rule 10.1 are defined by the Protocol.
10.2 RMP
(a) Within two weeks of their entry into the 37th America’s Cup being accepted, or within one week of
the first official publication of these AC Technical Regulations, whichever is later, each Competitor
shall appoint a team member as their recon representative and notify the Recon Administrator of
this person. This person shall be a member of all RMPs that the Competitor is a part of.
(b) Any change in a Competitor’s RMP representative shall be notified to the Recon Administrator.
(c) The Recon Administrator may convene and manage meetings of RMPs, but shall not be entitled to
vote.
(d) Decisions within RMPs shall be made by a majority vote. In the event of a tie, a casting vote shall be
given to:
(i) the Defender, for the RMP that follows the Challenger of Record; and
(ii) the Challenger of Record, for all other RMPs.
(e) Any Competitor currently in default of its obligation under Article 20 of the Protocol shall be ineligible
to participate in an RMP.
(b) Each Recon Unit will comprise two people, of which at least one shall hold any licence required to
operate the recon vessel in the operating country.
(c) It is envisaged that Recon Unit personnel shall have expertise in sailing and the America’s Cup envi‐
ronment, and that at least one member of the team shall have experience in media content gener‐
ation. However, the decision on personnel will be solely the responsibility of the relevant RMP.
(d) An RMP may ask an Observed Competitor for a recommendation of suitable local personnel but
shall not be obliged to follow that recommendation.
(e) Compensation for each Recon Unit will be the same for all contracted Recon Units, as outlined
in Part 12 of these Conditions; other contractual terms will also be identical except as otherwise
required by applicable laws. Initial discussions with prospective Recon Unit personnel shall be be‐
tween those prospective personnel and the respective RMP. When an agreement is reached, the
RMP shall inform the Recon Administrator of their chosen personnel, who will then confirm the
appointment with the recon personnel and make arrangements for payment of their compensation.
The Recon Administrator shall not refuse any appointment unless a person is not legally permitted
to work in the given role, or is determined by the Arbitration Panel to be unsuitable for the role
following an application by the Observed Competitor or the Recon Administrator.
(f) A Recon Unit shall be engaged from one week before the first Sailing Session until the termination
of the joint reconnaissance programme.
(g) A Recon Unit shall travel with their Observed Competitor to any location where they are sailing,
including the Match venue, except that they shall only travel to the venue of an Initial Preliminary
Regatta if the Observed Competitor is sailing at that venue:
(i) outside of the period during which sailing in an in class AC40 Class Yacht is not required to
be notified, observed or declared as a Sailing Session by Rule 10.1 (c); or
(ii) any yacht other than an in class AC40 Class Yacht,
where the italicised terms are defined by the Protocol. Travel and accommodation costs for each
Recon Unit shall be dealt with in accordance with Part 12 of these Conditions.
(h) Alternatively, an RMP may elect to switch their Recon Unit personnel to local personnel at each
venue at which their Observed Competitor is sailing.
(b) With the agreement of the Recon Administrator in consultation with the respective Recon Unit,
an Observed Competitor may provide a recon vessel whose specifications fall slightly below those
required by Rule 10.5 (a). However, if this recon vessel proves unfit for purpose as determined by the
Recon Administrator and the Recon Unit, the Observed Competitor shall be required to replace
the recon vessel with a vessel that meets the requirements of Rule 10.5 (a) within a time frame
determined by the Recon Administrator.
(c) An Observed Competitor shall make best endeavours to ensure the provided recon vessel is al‐
ways in service. If the provided vessel is at any time inoperable or out of service, and a suitable
replacement boat is not available, the Recon Unit shall be entitled to observe from the Observed
Competitor’s primary chase boat.
(d) An Observed Competitor shall either ensure the recon vessel boat is fuelled for a day, or provide
the Recon Unit with a fuel card or other payment method for purchasing fuel.
(e) Subject to the relevant Recon Unit’s operational requirements, an Observed Competitor may on
occasion place team members, VIPs or media on the provided recon vessel, to accompany the Recon
Unit, but the boat shall be skippered by the Recon Unit who shall make all decisions about the boat’s
location and schedule. If additional personnel on recon vessels are found to hinder the operational
duties of the Recon Units, the combination of all RMPs can elect to suspend this right.
(f) Unless agreed otherwise between the Recon Unit and the Observed Competitor, a Recon Unit
shall only use the recon vessel for reconnaissance of an Observed Competitor whilst sailing, before
sailing, or after sailing, or to re‐fuel the vessel, etc.
10.6 Notification
(a) An Observed Competitor shall notify their RMP and the Recon Administrator a minimum of two
months prior to their first roll out of a new yacht into public view at any sailing venue, in preparation
for their first Sailing Session. A sailing venue is a location where a Competitor will launch a yacht
and the zone within a radius of 10 km around that location.
(b) An Observed Competitor shall notify their RMP and the Recon Administrator a minimum of two
months before sailing at a new location (i.e. from a different base).
(c) It is strictly prohibited for a Competitor to sail or tow a yacht at any location without having notified
their RMP and the Recon Administrator as required above.
(d) Once a Recon Unit is appointed, the Recon Administrator shall put them in contact with their Ob‐
served Competitor, who shall arrange access and notification.
(e) Prior to and during a Sailing Session at a sailing venue, an Observed Competitor must provide 24
hours notice to their Recon Unit of their intent to roll out of their enclosed structure into public view
for any reason, and of their intent to launch, sail or tow any of their yachts. The Competitor should
notify the Recon Unit again as soon as possible if that roll out, launch or sailing is cancelled. They
shall keep the Recon Unit informed of planned roll‐outs and launch times.
(f) A Competitor must notify a Recon Unit of planned Sailing Sessions, days off and extended non‐
sailing periods as soon as they are known and notify them again as soon as possible if those plans
change. The notice period for any such notification of a Sailing Session shall not be less than the
gap between consecutive Sailing Sessions.
(g) Each time a Competitor sends an updated component schedule to the Measurement Committee,
a copy shall also be sent to their RMP, Recon Unit and AC Media. This component shall indicate
component IDs and versions but need not include any descriptions.
(h) Notification shall be by text or email.
10.7 Access
(a) A Competitor shall provide their Recon Unit access to the forecourt from which they launch their
yachts in a location that provides an unobstructed view of the yacht (except where obstructed by
the yacht’s cradle, etc). Such location shall be no more 25m from the usual location of the mast
base of the yacht when preparing to launch.
(b) A Competitor shall provide access to the edge of a wharf overlooking the yacht when at the dock,
or to the dock itself, no further than 25m from the mast base of the yacht.
(c) Recon Units must abide by the health and safety regulations of the Observed Competitor, and
may be required to move from the nominated locations during crane operations, etc. However, the
Observed Competitor shall not impose health and safety regulations on their Recon Unit that are
above and beyond those of the Observed Competitor’s own team members, and shall provide the
Recon Unit with the appropriate health and safety training if necessary for them to observe a yacht
launch.
(d) Following a sailing day, a Competitor shall provide access to one sailor who sailed on the yacht that
day, or a designer who was on the water, for an interview lasting no more than 3 minutes, within 15
minutes of docking. This interview shall be with a:
(i) helmsperson at least 25% of the occasions;
(ii) foil or aero trimmer, or grinder, on at least 25% of the occasions;
(iii) a designer on at least 25% of the occasions.
(e) On request, a Competitor shall provide access to a suitable member of their technical team to pro‐
vide commentary or explanation on an aspect of another Competitor’s yacht, a recent interpretation
draft, Class Rules amendment, or similar.
(f) Competitors shall not be obstructive in answering interview questions, and whilst they are permitted
to withhold confidential information, shall provide an informative report on the sailing day.
(b) Recon Units shall not use any photo or video equipment for recon except that standard equipment
provided, and/or their own personal mobile phones.
(e) As soon as possible, compile and collate images, videos and daily summaries for distribution to Com‐
petitors and AC Media. These summaries shall include observations and comments on photos and
videos, in addition to some statistics, and shall be uploaded to the Recon File Store. The format of
the reports may be specified by AC Media.
(f) A Competitor from a Recon Unit’s RMP may propose specific areas of interest to focus on, but any
information captured by the Recon Unit shall be shared equally with all Competitors via the Recon
File Store. A Recon Unit shall not provide any photos, video or other data to any Competitor except
via the Recon File Store, but this does not prohibit verbal discussions between a Competitor and a
Recon Unit.
(g) On request from AC Media, a Recon Unit shall interview a member of their Observed Competitor’s
technical team on specific technical questions, and upload that interview to the Recon File Store.
(h) Take photos and video of a Competitor’s yacht when in public view or when it is not in an enclosed
structure, such as during roll‐out, lifting or afloat, whether or not it is a sailing day.
10.11 AC Media
(a) AC Media shall employ a dedicated technical writer with sailing and America’s Cup expertise to edit
and supplement recon data with technical commentary sourced from:
(i) Analysis of information provided by Recon Units
(ii) New components declarations; and
(iii) Interpretation and amendment analysis.
(b) AC Media shall publish edited information supplied by Recon Units on a technical area of the Offi‐
cial America’s Cup Website and the Official America’s Cup Social Media Channels. This will include
feature stories, interviews, photos, videos and sailing statistics.
(c) Stories and interviews provided by Recon Units shall be credited on the website with the names of
the Recon Unit personnel, which is intended to encourage good quality commentary and content
from those teams.
10.12 Costs
(a) The compensation for each member of a Recon Unit shall be a:
(i) monthly retainer to be agreed by COR/D;
(ii) an additional contracted rate to be agreed by COR/D for any day that falls within a Sailing
Session.
These costs shall be borne by the Observed Competitor. The Recon Administrator will calculate
and invoice each Observed Competitor for the relevant Recon Unit costs on a monthly basis.
(b) It is expected that Recon Unit members will, in general, already be based in the location where the
Observed Competitor will be sailing. As such, when operating at the home base of the Observed
Competitor, no additional expenses shall be payable to a Recon Unit. However, an RMP may choose
to make their own arrangements to provide accommodation and travel expenses for their chosen
Recon Unit if necessary, those costs to be shared equally between the Competitors of that RMP.
(c) An Observed Competitor shall be responsible for providing travel and accommodation for their Re‐
con Unit, for any venue at which they sail away from their home base except the Match venue. Such
travel and accommodation shall be of a standard equivalent to that provided to that Competitor’s
own team members.
(d) The Recon Administrator shall arrange travel and accommodation for Recon Units at the Match
venue, these costs to be shared by all Competitors.
10.13 Restrictions
(a) Competitors are prohibited from carrying out their own reconnaissance on other Competitors.
(b) When on the water, Competitors should at all times make all reasonable attempts to avoid being
close to any other Competitor’s yacht.
(c) When two or more Competitors are sailing at the same location they may find themselves in the
same stretch of water from time to time. In these situations, Competitors’ yachts or other boats
shall not make any attempt to follow or approach each other’s yachts unless requested to provide
assistance by the other Competitor.
(d) Taking photos or videos of another Competitors’s yacht is prohibited, except:
(i) another Competitors’s yacht is permitted to appear occasionally in the background of videos
taken from onboard a Competitors’s yacht; and
(ii) casual photos taken on a mobile phone from shore are permitted.
(e) It is prohibited to make any estimations, or electronic position, speed or course measurements of
the performance of another Competitors’s yacht.
(f) Competitors shall not obstruct Recon Units from performing their roles efficiently, and shall be
always courteous and considerate to their assigned Recon Unit.
(g) As exceptions to the Rules in Section 10.13:
(i) If Competitors accidentally find themselves close to another Competitor’s yacht, they are
permitted to observe that yacht from their own yacht, or from an accompanying team
boat (for example a supporting chase boat as defined by Rule 8.3, or a VIP boat) subject
to Rules 10.13 (b), 10.13 (c), 10.13 (d) and 10.13 (e).
(ii) At an Initial Preliminary Regatta, during the period when sailing an in class AC40 Class Yacht
is not required to be notified, observed or declared as a Sailing Session by Rule 10.1 (c),
Rules 10.13 (b) and 10.13 (c) do not apply for Official Practice, Official Training or racing
providing that Competitors are sailing only in class AC40 Class Yachts, where the italicised
terms are defined by the Protocol.
(iii) Following the launch of the Defender’s first AC40 Class Yacht, if invited to do so by the De‐
fender, Competitors may observe the sailing of that yacht from land or from a chase boat
for the period extended by the invitation only.
10.14 Remedies
(a) A Competitor that fails to:
(i) notify a Recon Unit of an intended outing;
(ii) provide a suitable recon vessel or access to their primary chase boat; or
(iii) provide other access as required herein;
shall be referred to the Regatta Director and is subject to a fine of NZ$10,000 for the first offence,
NZ$20,000 for the second offence, and so on for each subsequent offence.
(b) If the breach in Rule 10.14 (a) is considered to be deliberate by the relevant RMP, in consultation
with their Recon Unit, the matter shall be referred initially to Regatta Director and ultimately to the
Arbitration Panel who shall determine additional remedies (including points penalties).
(c) If a Competitor fails to give the required notification for a Recon Unit to witness the launch of a new
component or component version, as declared to the Measurement Committee, in addition to the
fine listed above, that Competitor shall be obliged to immediately make that component available
for viewing to the Recon Unit, whether on the yacht or otherwise.
(d) Any other breach of these conditions shall also be referred to the Regatta Director in the first in‐
stance, and ultimately to the Arbitration Panel for remedy.
11 Definitions
11.1 AC Media
As defined in the Protocol.
11.3 AC36
The 36th America’s Cup, and the time period spanning from the completion of the final race of the
35th America’s Cup to the completion of the final race of the 36th America’s Cup.
11.4 AC37
The 37th America’s Cup, and the time period spanning from the completion of the final race of the
36th America’s Cup to the completion of the final race of the 37th America’s Cup.
The combination of the AC40 Class Rule and the AC Technical Regulations.
11.13 Appendage
A foil or a rudder.
11.14 Batten
A beam used to locally stiffen a sail.
11.16 Blueprint
An IGES file, drawing or other document or collection thereof that provides information about the
design and/or construction of a version of a component. Specific requirements for blueprints for
each component type are provided in the relevant sections of the AC75 Class Rule, these specific
requirements taking precedence over this general definition.
11.17 Cant
Rotation of a foil about the foil arm rotation axis.
11.21 CIS
Crew information system: an electronic system connected to the Media System to display the raw
or processed Competitor data output from the Media System to the crew, and to provide voice
communication between the crew.
The intersection or projected intersection of the leech and foot of a sail skin. The leech or foot will
be projected tangentially from the point where the leech or foot curvature reduces below a radius
of 1.0 m when approaching the intersection.
11.30 Competitor
As defined in the Protocol. Where the term Competitor is used in the context of interpretations or
amendments, it refers only to those Competitors that are still competing and who are not in default
of their payment obligations required by the Protocol and Class Rules.
A system used for the adjustment of control surfaces, including all mechanical, hydraulic and elec‐
trical components involved in supplying or transmitting power or information used for such adjust‐
ment.
11.34 COR/D
The Challenger of Record and the Defender jointly.
11.35 Core
Material that is bonded between two structural FRP skins in a sandwich construction, primarily to
transfer shear. Core includes any material that is bonded to both skins, such as a corrugated laminate
between two skins, but excludes:
(a) solid laminate or metal used within edge, taper or local reinforcement details; and
(b) adhesives and resins used to bond skins and core, or to fill honeycomb cells.
11.38 Deck
That part of the hull surface that is not the hull lower surface.
11.39 Defender
As defined in the Protocol.
The state of the rig as it is positioned on the hull before and after sailing with no sails hoisted.
11.41 ECC
Electrical control circuit: an electrical and/or electronic circuit within a control system and/or for
sending commands to an FCS.
11.43 Event
Any regatta that forms part of the 37th America’s Cup.
Forces applied from outside the yacht to the yacht, such as fluid pressure, fluid dynamic friction and
gravity.
11.45 FCS
Foil cant system: a supplied system for controlling the rotation of the foils about the foil arm cant
axes.
where each flight control shall relate to a single control surface actuator.
11.50 Foil
An appendage that can provide hydrodynamic side force and vertical lift.
A fairing to close a penetration in the hull that allows cant rotation of a foil arm.
A component of a foil that can be adjusted relative to a foil wing by a foil system.
11.60 Foot
The bottom edge of a sail skin.
A device that is moved by one or more crew members to provide control and/or power input, and
whose movement, resistance to movement or response can, where expressly permitted within the
AC75 Class Rules, be affected by certain parts of the yacht state. Examples are a sheet or winch
connected to a sail, a grinding pedestal connected to a mechanical drive train or hydraulic pump,
and a steering wheel connected through cables to a rudder.
11.64 FRP
Fiber‐reinforced polymer matrix composite.
11.65 Hardwired
Physically connected by electrical wires, including localised electromagnetic or optical coupling be‐
tween system components (e.g. galvanic isolation of protocol bus, optical isolation of IO device)
provided information exchange is confined to the wiring circuit.
11.66 HCC
Hydraulic control circuit.
11.67 Head
The top edge of a sail skin.
11.71 Hull
The main body of the yacht, including the bottom, sides, transom, deck, cockpit and internal struc‐
ture but not the mast, rigging, sails, appendages or fittings.
The monolithic or sandwich panel construction that forms the structure of the hull surface, exclud‐
ing:
(a) internal structure and local reinforcements such as bulkheads, ring frames, longituindal
beams, stringers and taping details; and
(b) surface finishes such as paint and vinyl.
low flow and high pressure into higher flow and lower pressure.
11.79 IG
The intersection of the centre line of the forestay with the leading edge of the mast, as shown in the
“Mast” section of the AC75 Class Rule.
11.80 ILS
Instrumentation and logging system: an electronic instrumentation circuit including devices such as
sensors, processing units and logging systems.
11.81 In class
The status of a supplied component that has not been modified outside the scope of any modifica‐
tions explicitly permitted by the Class Rules.
11.83 Isolated
Electrically insulated so as to prevent the passage of electricity, and physically separated so that
isolation is apparent by inspection. Isolated cabling may be bundled together, so long as individ‐
ual cables within a bundle can be followed, but cables from two isolated systems must not share
common connectors.
11.84 JG
The distance between MRP and the intersection of the centreline of the forestay and a plane 1.500 m
above MWP with the rig at dock tune as shown in the “Mast” section of the AC75 Class Rule.
11.85 Jib
11.86 Jury
As defined in the Protocol.
11.87 Launched
(a) First installed on an AC75 Class Yacht with that yacht afloat where the term appears in relation
to an AC75 Class Yacht.
(b) First installed on an AC40 Class Yacht with that yacht afloat where the term appears in relation
to an AC40 Class Yacht.
(c) First installed after 1 March 2021 on a LEQ12 yacht with that yacht afloat where the term
appears in relation to a LEQ12 yacht.
11.88 LCP
Longitudinal centre plane.
11.89 LCS
Liquid Cooling System is a hydraulic system with the sole purpose to cool components, systems or
fluid within the yacht by the movement of a fluid, and has no effect on the yacht state other than
that resulting from the transfer of heat, does not provide feedback to other systems on the yacht
and can not do any work.
11.90 Leech
The aft edge of a sail skin.
A linear component may be constructed from multiple parts and fastened together mechanically
or with an interference fit, or contain voids in materials such as wood or foam which may open or
close under normal sailing loads. Such connections and materials are exempt from Rule 11.93 (b)
provided that the components, connections or materials are not engineered to provide deliberately
non‐linear characteristics through internal contact mechanisms.
11.94 LL
The distance from the head point to the clew point for a jib sail skin or the lower leech point for a
mainsail sail skin.
11.95 Longitudinal
Orthogonal to TRP.
11.98 LP
The distance, measured perpendicular to the luff, from the luff to the clew point of a sail skin.
11.99 Luff
The forward edge of a sail skin.
11.100 Mainsail
The combination of sail skins and associated components that are hoisted on the mast.
11.101 Mast
An assembly comprising the mast tube with any attached components and rigging that is not hoisted
with the mainsail or jib. It includes mainsail support structures and control systems such as booms
that are not part of the mainsail as well as the supplied rigging, rigging, halyards, spreaders, fit‐
tings, luff tracks, fairings, instrument displays, instrument sensors, cameras, cables, media equip‐
ment, flotation systems and hydraulic rams that remain as part of the rig whilst sailing. Sheets shall
be considered as part of the mast if they cannot be easily disconnected from mast structures and
control systems.
The lower mast zone as shown in the “Mast” section of the AC75 Class Rule.
A hydraulic actuator whose sole function is to convert force or torque into hydraulic pressure, and
translation or rotation into flow, that pressure and flow being delivered to a control surface actuator.
11.111 Mechanically
Only through contact of components, without the use of hydraulic, pneumatic, magnetic or electrical
components.
11.115 MRP
Mast rotation point. The point about which the mast base rotates relative to the hull.
11.116 MWP
The intersection or projected intersection of the leech and head of a sail skin. The leech or head
will be projected tangentially from the point where the leech or head curvature reduces below a
radius of 1.0 m when approaching the intersection.
11.123 Platform
The hull, foils, rudder and other systems, hardware, fittings, rigging and supplied equipment that is
weighed with those components.
11.126 Projected
The projected shape of a part is the shape of a shadow cast by that part on the specified plane from
a parallel light source acting normal to that plane.
11.127 Protocol
The Protocol governing the 37th America’s Cup made between the Royal New Zealand Yacht
Squadron and Royal Yacht Squadron Limited.
11.132 Recover
To drain oil from a hydraulic actuator chamber to:
(a) another hydraulic actuator chamber (whether or not of the same hydraulic actuator); or
(b) a high‐pressure hydraulic accumulator;
11.134 Rig
11.138 Rudder
An appendage positioned on the centreline of the hull which is rotated to affect yaw and trim.
Components of a sail for the purpose of attachment or applying pre‐tension of sail controls and
battens. If two or more components are rigidly connected together then they will be considered as
a single piece of sail hardware.
11.143 SHA
An SHA‐512 of a component’s blueprint, generated according to the Secure Hash Standard (SHS)
(FIPS PUB 180‐4) issued by the National Institute of Standards and Technology. This shall be gener‐
ated using a tool such as the Windows software “Hash Tool” by DigitalVolcano Software.
11.148 Strop
A length of rope with its two ends spliced together forming a continuous ring or band.
11.151 Symmetric
A component that is required to be symmetric must be designed to be exactly symmetric, and the
built shape must lie within the specified tolerance of the designed shape everywhere on its surface.
Such a component must also be designed to be almost exactly symmetric in its structure, where any
structural asymmetry can only result from details such as:
(a) asymmetries at the individual ply level (e.g. lap joints or staggers), provided the overall lami‐
nate has symmetric structural behaviour;
(b) fastenings across the symmetry plane; and
(c) right‐handed screw threads;
which are not designed to induce asymmetric structural behaviour.
(a) valve;
(b) stop or lock; or
(c) clutch or shifter.
Power supplied to a transmission actuator can do no work on a control surface, or on oil or gas
within an HCC, except for incidental work such as the displacement of oil by the plunger in a valve,
or a component of force applied by a chamfered lock pin that engages on a ram, providing such work
is insignificant in the context of overall power supplied to a control surface.
11.154 Transverse
Orthogonal to LCP.
11.155 TRP
11.156 Valve
A transmission actuator that controls the flow of oil within an HCC, such as a check valve, pressure
relief valve, or electrically powered control valve.
A volume within the hull surface that is separated from the remainder of the enclosed volume of
the hull by a watertight boundary, and shares a penetration with the hull surface.
11.158 Wetted
The wetted part of a component is that part of a component that extends or can extend outside of
the hull surface below the perimeter line.
11.159 Woolly
A piece of wool or light fabric used only for flow visualisation.
where the above are defined using the current time zone in New Zealand, being either New Zealand
Standard Time (NZST, UTC+12) or New Zealand Daylight Time (NZDT, UTC+13). For example a working
day beginning on Friday 8th July 2022 at 09:00 NZST ends on Monday 11th July 2022 at 09:00 NZST.
11.161 WSP
Wing symmetry plane.
11.162 Yacht
(a) An AC75 Class Yacht where the term appears in the AC75 Class Rule.
(b) An AC40 Class Yacht where the term appears in the AC40 Class Rule.
(c) An AC75 Class Yacht or a LEQ12 yacht where the term appears in the AC Technical Regula‐
tions.
12 Agreement
12.1 COR/D agreed to the publication of version 1.0 of these AC Technical Regulations on the 17th day of March
2022.
12.2 This version of the AC Technical Regulations shall replace the previous version and be in force when signed
by all signatories below. The replacement of the previous version with this version is an amendment ac‐
cording to Rule 7.3 (c).
8/4/2022
Date
INEOS Britannia
Ben
Name Ainslie Signature
Date
8/5/2022