Professional Documents
Culture Documents
75 Tongrovert 875 e
75 Tongrovert 875 e
product
guide
contents
Features 2
Specifications 3
Dimensions 5
Working Range 6
Bifold
Load Charts 7
Working Range 8
Bifold & Inserts
features
• 75 ton (68 mt) capacity Load Charts 10
• 41 ft-128 ft (12.6 m-39.0 m)
4 section, full power boom
Load Handling 11
• 33 ft-56 ft (10.1 m-17.0 m)
offsettable lattice
swingaway extension
• 20 ft (6.1 m) or 40 ft (12.2 m)
extension inserts
• Max. tip height of 232 ft. (70.6 m) w/56 ft. (17.0 m) bi- • Electronically controlled Cummins diesel
fold and (2) 20 ft. (6.3 m) inserts. engine provides plenty of power at the
jobsite.
specifications
Superstructure Swing
Two speed, planetary swing drive with foot-applied multi-disc
B
Boom wet brake. Spring applied, hydraulically-released swing brake. 3
41 ft. - 128 ft. (12.6 m - 39.0 m) four-section, sequenced Single position mechanical house lock, operated from cab.
synchronized full power boom. Maximum tip height: 138 ft. (41.9 Maximum speed: 2.0 RPM.
m).
Counterweight
Lattice Extension 18,000 lbs. (8 168 kg). Hydraulically installed and removed.
33 ft.-56 ft. (10.1 m-17 m) offsettable bifold lattice swingaway
extension. Offsets 0˚, 25˚ and 45˚. Stows alongside base boom Hydraulic System
section. Maximum tip height: 192 ft. (58.6 m). Two main pumps ([1] piston and [1] gear) with a combined
capacity of 133 GPM (503 LPM).
*Optional Lattice Extension Inserts Maximum operating pressure: 4000 psi (277.7 bar).
(2) x 20 ft. (6.1 m) lattice extension inserts. Installs between the Three section pressure compensated valve bank. Return line
boom nose and bifold extension, non-stowable. Maximum tip type filter with full flow by-pass protection and service indicator.
height: 232 ft. (70.6 m). Replaceable cartridge with micron filtration rating of 5/12/16. 263
gallon (995 L) hyd. reservoir. Carrier mounted oil cooler with
B
Boom Nose thermostatically controlled hydraulic motor driven fan/air to oil.
Four nylatron sheaves mounted on heavy-duty tapered roller System pressure test ports.
bearings with removable pin-type rope guards. Quick-reeving
type boom nose. Removable auxiliary boom nose with Hoist Specifications
removable pin type rope guard. Main and Auxiliary Hoist
Planetary reduction with automatic spring applied multi-disc wet
Boom Elevation brake. Electronic hoist drum rotation indicators and hoist drum
One double-acting hydraulic cylinder with integral holding valve cable followers.
provides elevation from -3° to +78°. Maximum Single Line Pull:
1st layers: 20,250 lb. (9 185 kg)
Load Moment 3rd layer: 17,010 lb. (7 715 kg)
& Anti-Two Block System 5th layer: 14,660 lb. (6 650 kg)
Standard “Graphic Display” load moment and anti-two block
system with audio-visual warning and control lever lockout. Maximum Permissible Line Pull:
These systems provide electronic display of boom angle, length, 16,800 lb. (7 620 kg) with 6 x 36 class rope
radius, tip height, relative load moment, maximum permissible 16,800 lb. (7 620 kg) with 35 x 7 class rope
load, load indication and warning of impending two-block
condition. The standard Work Area Definition System allows the Maximum Single Line Speed: 514 FPM (156 m/min)
operator to pre-select and define safe working areas. If the
crane approaches the pre-set limits, audio-visual warnings aid Rope Construction:
the operator in avoiding job-site obstructions. 6 x 37 EIPS IWRC, Special Flexible
35 x 7 Flex-X, Rotation Resistant
C
Cab
Full-vision, all-steel fabricated with acoustical lining and tinted Rope Diameter: 3/4" (19 mm)
safety glass throughout. Cab tilts to +20 degrees. Deluxe seat
incorporates armrest-mounted hydraulic single-axis controllers. Rope Length:
Dash panel incorporates gauges for all engine functions. Other Main Hoist: 600 ft. (182.8 m)
standard features include: hot water heater, cab circulating air Auxiliary Hoist: 600 ft. (182.8 m)
fan, sliding side and rear windows, sliding skylight with electric
wiper and sunscreen, electric windshield wash/wipe, fire Maximum Rope Stowage: 841 ft. (256 m)
RT875E
Carrier Brakes
Full hydraulic split circuit brakes operating on all wheels. Spring-
4 Chassis
F
applied, hydraulically released parking brake mounted on front
Box section frame fabricated from high-strength, low alloy steel. axle.
Front/rear towing and tie down lugs.
Tires
Outrigger System
O
Std. 29.5 x 25 - 34 bias ply, General.
Four hydraulic telescoping single-stage double box beam
L
outriggers with inverted jacks and integral holding valves. Three Lights
position setting, 0%, 50% and fully extended. All steel Full lighting including turn indicators, head, tail, brake and
fabricated, quick-release type round outrigger floats, 30.5 in. hazard warning lights.
(775 mm) diameter. Maximum outrigger pad load: 125,000 lb.
(56 700 kg). Maximum Speed
22 MPH (35 kph).
Outrigger Controls
Controls and crane level indicator located in cab. Gradeability (Theoretical)
75% (Based on 109,043 lb. [49 462 kg] GVW) 29.5 x 25 tires,
Engine 128 ft. (39.0 m) boom, plus 56 ft. (17.0 m) swingaway, 18,000 lb.
Cummins QSB 5.9L diesel, six cylinders, 275 bhp (205 kW) (8 165 kg) counterweight, 75T hookblock and 10T headache
(Gross) @ 2,500 rpm. Maximum torque: 730 ft. lbs. (990 Nm) @ ball).
1,500 RPM.
Miscellaneous Standard Equipment
Fuel Tank Capacity Full width steel fenders, full length aluminum decking, dual rear
72 gallons (273 L) view mirrors, hookblock tiedown, electronic back-up alarm, light
package, front stowage well, tachometer/hourmeter, rear wheel
Transmission position indicator, 36,000 BTU hot water cab heater, hoist
Full powershift with 6 forward and 6 reverse speeds. Front axle mirrors, engine distress A/V warning system, front/rear tie down
disconnect for 4 x 2 travel. and two lugs, coolant sight level indicator.
Axles
Front: Drive/steer with differential and planetary
reduction hubs rigid-mounted to frame.
RT875E
Oscillation Lockouts
Automatic full hydraulic lockouts on rear axle permits 10 in. (25.4
cm) oscillation only with boom centered over the front.
dimensions
ALL DIMENSIONS
ARE METER AND [INCH]
3340
5
[131.50]
7.8 [306]
OUTSIDE
TURN RADIUS
4.9 [194]
INSIDE TURN RADIUS
15214
[598.980] 3758
[147.96]
23 o
20o
2057
[81.00]
3688 3835
[145.20] 4216 [150.98]
[166.00] 8569
[317.36]
781
[30.76]
2553 TRACK
[100.50]
3150 RETRACKED
124.02
5283 MID EXTEND
[208.00]
7315 FULL EXTEND
[288.00]
Weights
GVW Front Rear
lb. kg lb. kg lb. kg
RT875E
180
33 ' EXT
170
160
150
140 128
60o
Height From Ground in Feet
120
130
o
50
110
120
100
110
40o
90
100
80
90
30o
70
80
60
70
20o 50
60
3
50
40
10o
78o MAX
30 BOOM ANGLE
20
0o
10
0
190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
AXIS OF
Operating Radius in Feet From Axis of Rotation ROTATION
118.95
[9'-11"]
RT875E
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
RT875E load chart
41.3-128 ft. 18,000 lbs 100% 360º 41.3 - 128 ft. 33 - 56 ft. 18,000 lbs 100% 360º
24' spread 24 ft. spread
Pounds
Pounds
Main Boom Length in Feet
Feet 33 ft. LENGTH 56 ft. LENGTH
41.3 50 60 **70 80 90 100 110 120 128
10
12
+150,000
(71)
+150,000
(67.5)
124,000
(74.5)
124,000
(72)
105,500
(77.5)
105,500
(75.5)
59,500
(78)
Feet
0o
#0021
11,900
20o
OFFSET OFFSET OFFSET
#0022
40o
#0023
0o
OFFSET
#0041
20o
#0042
40o
OFFSET OFFSET
#0043
7
130,000 124,000 104,000 59,500 42,100 *42,000 35 (78)
15
(63) (68.5) (72.5) (75.5) (78) (78) 11,900 6,060
100,000 99,850 85,900 59,500 42,100 42,000 *39,650 *31,950 40 (77) (78)
20
(54.5) (62) (67.5) (71) (74) (76) (78) (78) 11,900 *11,900 6,060
80,550 80,250 72,550 57,050 42,100 42,000 39,650 31,950 *25,750 *22,000 45
25 (75.5) (78) (77.5)
(44.5) (55) (62) (66.5) (70) (73) (75) (77) (78) (78) 11,900 10,600 *9,790 6,060
59,050 58,150 57,850 49,300 42,100 39,050 36,150 31,950 25,750 22,000 50 (73.5) (76.5) (78) (76)
30
(31.5) (47) (56) (62) (66) (69.5) (72) (74) (76) (77) 11,900 9,770 8,470 6,060
43,250 43,000 42,600 38,150 34,100 31,350 29,300 25,750 22,000 55 (71.5) (74.5) (77) (74.5)
35 (37.5) (49.5) (57) (62) (66) (68.5) (71.5) (73.5) (74.5) 11,000 9,020 7,920 6,060 *6,060
33,600 33,400 32,950 33,750 30,050 27,500 25,650 23,900 22,000 60 (69.5) (72.5) (75) (72.5) (78)
40 (24.5) (42.5) (52) (58) (62) (65.5) (68.5) (71) (72.5)
65 10,000 8,360 7,430 6,060 5,900
26,600 26,200 27,400 26,750 24,400 22,700 21,450 20,650 (67.5) (70.5) (73) (71) (76.5)
45 (34) (46) (53) (58.5) (62) (65.5) (68) (70)
70 9,190 7,780 6,980 6,060 5,730 *5,060
See 21,600 21,150 22,450 23,250 21,850 20,250 19,100 18,350 (65.5) (68.5) (71) (69.5) (75) (78)
50 Note 16 (22) (39.5) (48.5) (54.5) (59) (62.5) (65.5) (67.5)
75 8,460 7,260 6,580 6,060 5,330 4,640
17,250 18,650 19,400 19,700 18,200 17,100 16,400 (63.5) (66.5) (69) (67.5) (73) (77)
55 (31.5) (43) (50) (55) (59.5) (63) (65) 7,820 6,790 6,210 6,040 4,980 4,370
80 (61.5) (64.5) (66.5) (66) (71.5) (75.5)
14,200 15,600 16,400 17,050 16,450 15,450 14,750
60 (21) (37) (45.5) (51.5) (56) (60) (62.5) 7,250 6,370 5,870 5,570 4,650 4,120
85 (59.5) (62) (64.5) (64) (69.5) (73.5)
13,100 13,850 14,550 14,950 14,000 13,350
65 (29.5) (40.5) (47.5) (53) (57) (59.5)
90 6,740 5,990 5,560 5,150 4,360 3,890
11,050 11,800 12,450 12,900 12,700 12,150 (57) (60) (62) (62.5) (67.5) (71.5)
70
(19) (34.5) (43) (49.5) (54) (57) 6,290 5,640 5,280 4,780 4,090 3,680
95 (55) (57.5) (60) (60.5) (66) (69.5)
75 10,000 10,700 11,200 11,600 11,050
(28) (38.5) (45.5) (51) (54) 5,880 5,320 5,020 4,440 3,840 3,480
100 (52.5) (55.5) (57.5) (58.5) (64) (67.5)
80 8,540 9,170 9,670 10,150 10,100
(18) (33) (41.5) (47.5) (51) 5,510 5,030 4,770 4,130 3,610 3,300
105 (50) (53) (55) (56.5) (62) (65.5)
85 7,860 8,360 8,850 9,180
(26.5) (37) (44) (48) 5,170 4,760 4,550 3,850 3,400 3,130
110
6,710 7,210 7,700 8,050 (47.5) (50.5) (52) (54.5) (60) (63.5)
90
(17.5) (32) (40) (44.5) 4,830 4,510 4,340 3,590 3,200 2,970
115
6,200 6,700 7,050 (45) (47.5) (49.5) (52.5) (58) (61)
95
(25.5) (35.5) (41) 4,230 4,280 4,150 3,360 3,020 2,820
120 (42) (45) (46.5) (50.5) (55.5) (59)
100 5,310 5,800 6,160
(17) (30.5) (37) 3,690 3,960 3,140 2,840 2,680
125 (39) (41.5) (48) (53.5) (56.5)
5,010 5,360
105
(25) (32.5) 3,200 3,430 2,940 2,690 2,540
130 (36) (38.5) (46) (51) (54)
4,290 4,640
110
(16.5) (27.5) 135 2,740 2,930 2,760 2,540 2,420
4,000 (32) (35) (43.5) (48.5) (51.5)
115
(21.5) 140 2,320 2,480 2,590 2,400 2,300
3,410 (28) (30.5) (41) (46) (48.5)
120 1,940 2,430 2,270
(10.5) 145
Minimum boom angle (deg.) for indicated length (no load) 9 (23) (38.5) (43.5)
1,580 2,070 2,140
Maximum boom length (ft.) at 0 deg. boom angle (no load) 120 150 (16.5) (35.5) (40.5)
#LMI operating code. Refer to LMI manual for instructions. 1,730 2,030
*This capacity is based upon maximum obtainable boom angle. 155
(32.5) (37)
Note: ( ) Boom angles are in degrees.
+9 parts line required to lift this capacity (using aux. boom nose). Refer to Operator's & Safety Handbook for reeving diagram. 160 1,420 1,710
(29) (33.5)
Lifting Capacities at Zero Degree Boom Angle
165 1,120
Boom Main Boom Length in Feet (24.5)
Angle 41.3 50 60 **70 80 90 100 110 120 Minimum boom angle
o 20,750 15,150 10,500 6,700 5,100 3,900 2,900 2,000 1,300 ( o) for indicated length 15 28 44 23 31 46
0 (34.1) (42.8) (52.8) (63) (72.8) (82.8) (92.8) (102.8) (112.8) (no load)
Note: ( ) Reference radii in feet. A6-829-103645 Maximum boom length
**This boom length is with inner-mid fully extended and outer-mid & fly fully retracted. o
(ft.) at 0 boom angle 110 110
(no load)
NOTE: ( ) Boom angles are in degrees. A6-829-103653
#LMI operating code. Refer to LMI manual for operating instructions.
*This capacity is based upon maximum boom angle.
NOTES:
1. All capacities above the bold line are based on structural strength of boom extension and do
not exceed 85% of tipping loads, in accordance with SAE J-765.
2. The 33 ft. extension length may be used with single or double part line lifting service. The 56
ft. extension length may be used for single line lifting service only.
3. For main boom lengths less than 128 ft. with the boom extension erected, the rated loads
are determined by boom angle. Use only the column which corresponds to the boom
extension length and offset for which the machine is set up. For boom angles not shown,
use the rating of the next lower boom angle.
4. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly
prohibited. Machine tipping with boom extension occurs rapidly and without advance
warning.
5. Boom angle is the angle above or below horizontal of the longitudinal axis of the boom base
section after lifting rated load.
6. Capacities listed are with outriggers properly extended and vertical jacks set only.
RT875E
7. When lifting over the main boom nose with 33 ft. or 56 ft. extension erected, the outriggers
must be fully extended or 50% extended (17 ft. 4 in. spread).
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
working range
Working range diagram with bi-fold extension and one insert
220
0o OFFSET 76' EXT
8 210
20o
40o OFFSET
200
190
180
170
160
150 70o
130
50o
110
120
100
110
40o
90
100
80
90
30 o
70
80
60
70
20o 50
60
41.3
50
40
10o
78o MAX
30 BOOM
ANGLE
20
0o
10
0
200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10
AXIS OF
ROTATION
Operating radius in feet from axis of rotation
118.95
RT875E
[9'-11"]
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
working range
Working range diagram with bi-fold extension and two inserts
240
0o OFFSET 96' EXT
230
40o
20o
9
220
210
200
190
180
170
160
140 128
Height from ground in feet
60o
120
130
50o
110
120
100
110
40o
90
100
80
90
30o
70
80
60
70
20o 50
60
41.3
50
40
10o
78o MAX
30 BOOM
ANGLE
20
0o
10
0
220 210 200 190 180 170 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20
AXIS OF
ROTATION
Operating radius in feet from axis of rotation
RT875E
118.95
[9'-11"]
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
RT875E load chart
NOTES:
41.3-128 ft. 20 ft. insert 18,000 lbs 100% 360º 41.3-90 ft. 18,000 lbs Stationary 360º 1. Capacities are in pounds
25 ft. spread and do not exceed 75%
Pounds Pounds of tipping loads as
10 Feet
76 ft. (56 ft. LENGTH + 1 INSERT) 96 ft. (56 ft. LENGTH + 2 INSERTS)
0o 20o 40o 0o
OFFSET OFFSET OFFSET OFFSET OFFSET OFFSET
20o 40o
Feet
#9005
50 4,850 12
49,200 40,750 2. Capacities are applicable
(78) (67.5) (72)
4,850 3,520 39,150 35,700 to machines equipped
55 15 (63) (68.5)
(77.5) (78)
24,200 24,350 22,800 22,000
with 29.6x25 (34 ply)
4,850 3,520 20
60 (76) (77.5) (54.5) (62) (67.5) (71) General tires at 76 psi
4,850 *5,290 3,520 16,200 16,200 15,600 15,950 15,850
65
(74.5) (78) (76.5)
25 (44.5) (55) (62) (66.5) (70) cold inflation pressure.
70 4,850 4,860 3,520 30 11,250 11,250 10,950 10,650 11,600 12,150 3. Capacities appearing
(73) (77.5) (75) (31.5) (47) (56) (62) (66) (69.5)
4,850 4,470 3,520 3,740 35 7,900 7,690 7,270 8,420 8,820 above the bold line are
75 (71.5) (76) (73.5) (78) (37.5) (49.5) (57) (62) (66)
4,730 4,110 *4,050 3,520 3,420 5,490 5,280 4,880 6,020 6,330
based on structural
80 40
(70) (74.5) (78) (72.5) (76.5) (24.5) (42.5) (52) (58) (62) strength and tipping
4,310 3,790 3,500 3,300 3,100 *3,250 3,430 3,110 4,130 4,480
85 (68.5) (73) (76.5) (71) (75) (78) 45 (34) (46) (53) (58.5) should not be relied upon
3,940 3,500 3,260 2,970 2,820 2,720 1,350 1,740 2,610 3,040 as a capacity limitation.
90 (67) (71) (75) (69.5) (73.5) (77) 50 (22) (39.5) (48.5) (54.5)
95 3,610 3,240 3,030 2,660 2,560 2,490
55 1,360 1,070 4. Capacities are applicable
(65.5) (69.5) (73) (68) (72) (75.5) (43) (50)
3,310 3,000 2,830 2,390 2,320 2,270 Minimum boom angle (deg.) for
only with machine on
100 (64) (68) (71.5) (66.5) (71) (74) 21 38.5 42 49
indicated length (no load) firm level surface.
105 3,040 2,770 2,630 2,140 2,100 2,070 Maximum boom length (ft.) at 0
(62) (66) (69.5) (65) (69.5) (72) deg. boom angle (no load)
50 5. On rubber lifting with
2,790 2,570 2,450 1,920 1,900 1,890 #LMI operating code. Refer to LMI manual for instructions. boom extensions not
110 (60.5) (64.5) (68) (63.5) (68) (70.5) Note: ( ) Boom angles are in degrees.
115 2,560 2,370 2,280 1,710 1,710 1,710 *This boom length is with inner-mid fully extended and outer-mid & fly fully permitted.
(58.5) (62.5) (66) (62) (66.5) (69) retracted.
2,350 2,200 2,120 1,520 1,540 1,550 Lifting Capacities at Zero Degree Boom Angle 6. For pick and carry
120 (57) (61) (64) (60.5) (64.5) (67.5)
Boom Main Boom Length in Feet operation, boom must be
2,160 2,030 1,970 1,350 1,380 1,390 Angle
125 (55) (59) (62) (59) (63) (66) 41.3 50 centered over front of
1,990 1,880 1,830 1,190 1,230 1,250 8,340 4,400
130 0o (34.1) (42.8) machine, mechanical
(53) (57) (60) (57.5) (61.5) (64)
1,820 1,730 1,700 1,040 1,080 1,110 Note: ( ) Reference radii in feet. A6-829-0103649A swing lock engaged and
135 (51.5) (55) (58) (56) (60) (62.5)
1,670 1,590 1,570 load restrained from
140 (49.5) (53) (56) swinging. When handling
145 1,530 1,470 1,450
(47) (51) (53.5) loads in the structural
1,400 1,340 1,340
150 (45) (49) (51.5) range with capacities
155
1,270 1,230 1,230
41.3-90ft.
close to maximum
(43) (46.5) (48.5) 18,000 lbs Pick & Carry 360º
1,160 1,120 1,130 Up to 2.5 mph ratings, travel should be
160
(40.5) (44) (46)
Pounds reduced to creep speeds.
165 1,050 1,020
(38) (41.5)
#9006
7. Axle lockouts must be
Minimum boom angle
(o) for indicated 36 40 44 54 58 60 functioning when lifting
length (no load) Main Boom Length in Feet
Maximum boom Feet 41.3 50 60 *70 80 90
on rubber.
length (ft.) at 0o boom 70 60 8. All lifting depends on
angle (no load) 12 59,450 49,400
(67.5) (72)
NOTE: ( ) Boom angles are in degrees. A6-829-103655
49,650 49,400
proper tire inflation,
#LMI operating code. Refer to LMI manual for operating instructions. 15
*This capacity is based upon maximum boom angle. (63) (68.5) capacity and condition.
RT875E - S/N 223983 38,100 37,800 36,850 29,750
20 (54.5) (62) (67.5) (71) Capacities must be
25 30,000 29,700 29,200 29,700 reduced for lower tire
(44.5) (55) (62) (66.5)
NOTES: 30 24,100 23,750 23,500 23,850 24,450 inflation pressures. See
(31.5) (47) (56) (62) (66)
1. All capacities above the bold line are based on structural 18,000 17,900 18,150 19,000 19,900
lifting capacity chart for
35 (37.5) (49.5) (57) (62) (66)
strength of boom extension and do not exceed 85% of tipping tire used. Damaged tires
40 13,650 13,700 13,750 14,700 15,500
loads, in accordance with SAE J-765. (24.5) (42.5) (52) (58) (62) are hazardous to safe
9,400 9,290 11,500 12,300 operation of crane.
2. The 56 ft. boom extension length may be used for single line 45 (34) (46) (53) (58.5)
lifting service only. 50 7,420 7,200 8,220 8,960 9. Creep – Not over 200 ft.
(22) (39.5) (48.5) (54.5)
3. For main boom lengths less than 128 ft. with the boom extension 5,450 6,510 7,220 of movement in any 30
55 (31.5) (43) (50)
erected, the rated loads are determined by boom angle. Use only minute period and not
60 3,970 5,060 5,740
the column which corresponds to the boom extension length (21) (37) (45.5) exceeding 1 mph.
65 3,810 4,460
and offset for which the machine is set up. For boom angles not (29.5) (40.5)
shown, use rating of the next lower boom angle. 70 2,720 3,350
(19) (34.5)
4. WARNING: Operation of this machine with heavier loads than 75 2,380
(28)
the capacities listed is strictly prohibited. Machine tipping with 1,520
80 (18)
boom extension occurs rapidly and without advance warning.
Minimum boom angle (deg.) for indicated length (no load) 0
5. Boom angle is the angle above or below horizontal of the Maximum boom length (ft.) at 0 deg. boom angle (no load) 90
longitudinal axis of the boom base section after lifting rated load. #LMI operating code. Refer to LMI manual for instructions.
RT875E
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
load handling
Weight Reductions for Load Handling Devices
33 FT.-56 FT. FOLDING BOOM EXTENSION
*33 ft. Extension (Erected) - 3,700 lb.
*56 ft. Extension (Erected) -
*76 ft. (1 insert Erected) -
7,830 lb.
10,350 lb.
11
*96 ft. (2 inserts Erected) - 13,300 lb.
*Reduction of main boom capacities
(no deduct required for stowed boom extension)
When lifting over swingaway and/or jib combinations, deduct total weight
of all load handling devices reeved over main boom nose directly from
swingaway or jib capacity.
NOTE: All load handling devices and boom attachments are considered
part of the load and suitable allowances MUST BE MADE for their
combined weights. Weights are for Grove furnished equipment.
CG OF OVER OVER
LOAD FRONT REAR
SEE NOTE
RT875E
FRONT
AT BOTTOM
DIAGRAM
FOR LIFTING CENTERLINE
OVER DIAGRAM
ON OUTRIGGERS OF ROTATION
SIDE FOR LIFTING
ON TIRES
Bold lines determine the limiting position of any load for operation within working areas indicated.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and
other instructional plates must be read and understood prior to operating the crane.
Manitowoc Crane Group - Americas
Manitowoc, Wisconsin Facility
Tel: [Int + 001] 920 684 6621
Fax: [Int + 001] 920 683 6277
Shady Grove, Pennsylvania Facility
Tel: [Int + 001] 717 597 8121
Fax: [Int + 001] 717 597 4062
Manitowoc Crane Group - EMEA
Europe Middle East & Africa
Tel: [Int + 33] (0) 191 565 6281
Fax: [Int + 33] (0) 4 72 18 20 20
Manitowoc Crane Group - UK
Europe Middle East & Africa
Tel: [Int + 44] (0) 191 565 6281
Fax: [Int + 44] (0) 191 564 0442
Manitowoc Crane Group - Germany
(Sales, Parts & Service)
Tel: [Int + 49](0) 2173 8909 0
Fax: [Int + 49] (0) 2173 8909-30
Manitowoc Crane Group - France
France & Africa (Sales, Parts & Service)
Tel: [Int + 33] (0) 1 303 13150
Fax: [Int + 33] (0) 1 303 86085
Manitowoc Crane Group - Netherlands
(Sales, Parts & Service)
Tel: [Int + 31] (0) 76 578 39 99
Fax: [Int + 31] (0) 76 578 39 78
Manitowoc Crane Group - Italy
Italy & Southern Europe (Sales, Parts & Service)
Tel: [Int + 39] (0) 331 49 33 11
Fax: [Int + 39] (0) 331 49 33 30
Manitowoc Crane Group - Portugal
Portugal & Spain (Sales, Parts & Service)
Tel: [Int + 351] (0) 22 968 08 89
Fax: [Int + 351] (0) 22 968 08 97
Manitowoc Crane Group - Singapore
Asia/Pacific excl China (Sales, Parts & Service)
Tel: [Int + 65] 6861 1733
Fax: [Int + 65] 6862 4040 / 4142
Manitowoc Crane Group - Shanghai
China (Sales, Parts & Service)
Tel: [Int + 86] (0) 21 64955555
Fax: [Int + 86] (0) 2164852038
Manitowoc Crane Group - Beijing
China (Sales, Parts & Service)
Tel: [Int + 86] (0) 10 646 71690
Fax: [Int + 86] (0) 10 646 71691
Manitowoc Crane Group - Middle East
(Sales)
Tel: [Int + 971] (0) 4 348 4478
Fax: [Int + 971] (0) 4 348 4478
(Parts & Service)
Tel: [Int + 973] (0) 9 660 899
Fax: [Int + 973] (0) 2 707 740
Distributed By:
Constant improvement and engineering progress make it necessary that we reserve the right to make
specification, equipment, and price changes without notice. Illustrations shown may include optional equipment
and accessories, and may not include all standard equipment.
www.manitowoccranegroup.com
1004-2M Printed in USA Form No. RT875E PG Part No. 04-023 Manitowoc Crane Group 2004