Controlled No: TEDSNLAO
How to Replace the Old Version PCB tothe New Version PCB
1m case ofthe replacing the Old version PCB (FECA34** ) tothe New version PCB (10528) ofthe Clesta-I (A) Unit.
Please follow the instructions below.
“If seplacing the New version {o New version PCB. Connect ll eanections same position after PCT is replace.
‘Mor changes inthis PCB
bn blow
1. Changes pitch ofthe fixing hole on the PCB
2. Adding light pck ternal individually. Posmse
[New Version A type Dr.control PCB
3. Changes some connector numbers brorpcirel ri}
OldVersion Atype
Dr.Control PCB :FECAS4**
New Version A type
De-Control PCB 160528"
1. How fo Replace the Old Version PCB to the New Version PCD.
[Now version PCH ean be compatible (conectble) withthe old version PCB inthe same wing,
Fellow the instruction below o replace the PCB.
1) Gently diene he all consis fn the ad version PCB.
2) Remove the old version PCR fom the PCB bracket (Remove it rem 4 space)
3) Remove 4 spacers fom the PCB bracket which was fxing PCB to PCB bracket,
4) ser 4 spacers pacer with double sided tape) to the new version ®CB and attach to the PCB bracket,
(4 spacers are provided with new version PCB)
5) Connect the Purple and Yellow/Green wires for Hight pack PCH te CNIS. (Inthe Optic Speeteation)
Decor pe Toee
LUnhepmck PeControlled No: IEOSNLAD
{6, Connect Ble and Orange wits from the air switch to CN,
7) Remove the Jumper pin from the CNH on theo version PCB aad stach it to CN9 on the new version PCB,
Srconnalren Fecasee DonaiPeneasan+
‘ont
I
8) Connect the 2P connector (Black, White wires) to CNIS onthe nev version PCB.Controlled No: 1EOSNLAD
9} Comrct all connecors which were removed at procesure (I) above. Connector numbers are diferent between od and
now version PCB. Pleas se connector numbers below.
‘SrcmarhnesFEcaaa+ canyos Dreier Fearne
‘Connector Number & Fonction “A Tipe Di Coto OR] We enced old Cw New PCR,
Funct TIE FECAT® aber 1GOSRH™ | be cart fhe fellowing pons
Tovar at a PCH, (ACI4V) CR cH
alice Am Air Bre Sit cx? G2
Commins tothe Chi (Tanaiasion] CNA Ns
DrMentrae Soc (107) xs a a
DeMentrae Sitch (0) exe ene
‘sletant Mera Sith er eNio7
‘ie Swit Fost Conal) oN ‘xb
Cpe & Hoo Fe Solensi Vac ce ‘exon,
Tnpt fom Light ask PCB eto ‘ens Pasian pac
eee eno CNS te te nw
‘Ramo
nis Wie 2) z RG en
ais Wie 3) ; NIB | Do satan wher ing om he
surety
iano Wie : BRIO satan wher lng om the
ech
‘WP igh Ai Swick LPI) on Ga hen oi po pcienion
ie cuca will anges Pa
‘i Lig Ai Sic 3) : ENO] arotconet wan ene om ie
sures).
HP Light Air oi (5) = GRIT) antec oe ling om
Sire
AP Light Ar Sitch (LP4) = RIE] te ntcamet wen ai aControlled No: IEOSNLAO
2. Wiring Diagram
1) Old Version A type De. Control PCR : FECASS*®
romecomnerecnen EA
rae
Air Motor opti)
wer HP2 HPs
2) New Version A type Dr, Control PCB : 160528°*
Note: This wiring dlagram i only supported when replacing the Old version PCB to New version PCD.
‘As for original connection ofthe New version PCB, please refer to wiring diagram inthe installation instrution of the
Cesta- Unit
i] Light pack PCB
=)
oo
bal
Marbrane ute
Ale Motor (opto)
Turbine optic
“Turbine (opie
i
Case