Professional Documents
Culture Documents
MAX4664/MAX4665/MAX4666
The MAX4664/MAX4665/MAX4666 quad analog switch- ♦ Low On-Resistance (5Ω max)
es feature 5Ω max on-resistance. On-resistance is
matched between switches to 0.5Ω max and is flat (0.5Ω ♦ Guaranteed RON Match Between Channels
max) over the specified signal range. Each switch can (0.5Ω max)
handle Rail-to-Rail® analog signals. The off-leakage cur- ♦ Guaranteed RON Flatness over Specified Signal
rent is only 5nA max at +85°C. These analog switches
Range (0.5Ω max)
are ideal in low-distortion applications and are the pre-
ferred solution over mechanical relays in automatic test ♦ Guaranteed Break-Before-Make (MAX4666)
equipment or in applications where current switching is
♦ Rail-to-Rail Signal Handling
required. They have low power requirements, require
less board space, and are more reliable than mechanical ♦ Guaranteed ESD Protection > 2kV per
relays. Method 3015.7
The MAX4664 has four normally closed (NC) switches, ♦ +4.5V to +36V Single-Supply Operation
the MAX4665 has four normally open (NO) switches, and
±4.5V to ±20V Dual-Supply Operation
the MAX4666 has two NC and two NO switches that
guarantee break-before-make switching times. ♦ TTL/CMOS-Compatible Control Inputs
These switches operate from a single +4.5V to +36V
supply or from dual ±4.5V to ±20V supplies. All digital Ordering Information
inputs have +0.8V and +2.4V logic thresholds, ensuring
TTL/CMOS-logic compatibility when using ±15V sup- PART TEMP. RANGE PIN-PACKAGE
plies or a single +12V supply. MAX4664CSE 0°C to +70°C 16 Narrow SO
MAX4664CPE 0°C to +70°C 16 Plastic DIP
Applications
MAX4664ESE -40°C to +85°C 16 Narrow SO
Reed Relay Replacement PBX, PABX Systems MAX4664EPE -40°C to +85°C 16 Plastic DIP
Test Equipment Audio-Signal Routing Ordering Information continued at end of data sheet.
Communication Systems Avionics
Pin Configurations/Functional Diagrams/Truth Tables
TOP VIEW
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
5Ω, Quad, SPST,
CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
MAX4664/MAX4665/MAX4666
Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
TA = +25°C 3 4
COM_ to NO_ or NC_ ICOM_ = 10mA,
RON Ω
On-Resistance VNO_ or VNC_ = ±10V
TA = TMIN to TMAX 5
2 _______________________________________________________________________________________
5Ω, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued)
MAX4664/MAX4665/MAX4666
(V+ = +15V, V- = -15V, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at
TA = +25°C.) (Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
POWER SUPPLY
Power-Supply Range ±4.5 ±20.0 V
TA = +25°C -0.5 0.001 0.5
Positive Supply Current I+ VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
TA = +25°C -0.5 0.001 0.5
Negative Supply Current I- VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
TA = +25°C -0.5 0.001 0.5
Logic Supply Current IL VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
TA = +25°C -0.5 0.001 0.5
Ground Current IGND VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
SWITCH DYNAMIC CHARACTERISTICS
Figure 2, TA = +25°C 130 275
Turn-On Time tON ns
VCOM_ = ±10V TA = TMIN to TMAX 400
Figure 2, TA = +25°C 90 175
Turn-Off Time tOFF ns
VCOM_ = ±10V TA = TMIN to TMAX 300
Break-Before-Make Time Delay
VCOM = 10V 5 30 ns
(MAX4666)
Charge Injection Q CL = 1.0nF, VGEN = 0, RGEN = 0, Figure 3 300 pC
Off-Isolation (Note 7) VISO RL = 50Ω, CL = 5pF, f = 1MHz, Figure 4 -62 dB
Crosstalk (Note 8) VCT RL = 50Ω, CL = 5pF, f = 1MHz, Figure 5 -60 dB
NC or NO Capacitance COFF f = 1MHz, Figure 6 34 pF
COM Off-Capacitance CCOM f = 1MHz, Figure 6 34 pF
On-Capacitance CCOM f = 1MHz, Figure 7 150 pF
_______________________________________________________________________________________ 3
5Ω, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply
MAX4664/MAX4665/MAX4666
(V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
(Note 2)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
ANALOG SWITCH
Input Voltage Range VCOM_, VNO_,
0 V+ V
(Note 3) VNC_
TA = +25°C 5.5 8
COM_ to NO_ or NC_ ICOM_ = 10mA,
RON Ω
On-Resistance VNO_ or VNC_ = 10V
TA = TMIN to TMAX 10
COM_ Off-Leakage Current VCOM_ = 1V, 10V; TA = +25°C -0.5 0.01 0.5
ICOM_(OFF) nA
(Notes 6, 9) VNO_ or VNC_ = 10V TA = TMIN to TMAX -5 5
VCOM_ = 1V, 10V; TA = +25°C -1 0.02 1
COM_ On-Leakage Current
ICOM_(ON) VNO_ or VNC_ = 1V, nA
(Notes 6, 9)
10V or floating TA = TMIN to TMAX -10 10
LOGIC INPUT
Input Current with Input Voltage
IIN_H IN_ = 2.4V, all others = 0.8V -0.5 0.001 0.5 µA
High
Input Current with Input Voltage
IIN_L IN_ = 0.8V, all others = 2.4V -0.5 0.001 0.5 µA
Low
Logic Input Voltage High VIN_H 2.4 V
Logic Input Voltage Low VIN_L 0.8 V
POWER SUPPLY
Power-Supply Range 4.5 36.0 V
TA = +25°C -0.5 0.001 0.5
Positive Supply Current I+ VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
TA = +25°C -0.5 0.001 0.5
Logic Supply Current IL VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
TA = +25°C -0.5 0.001 0.5
Ground Current IGND VIN = 0 or 5V µA
TA = TMIN to TMAX -5 5
4 _______________________________________________________________________________________
5Ω, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single Supply (continued)
MAX4664/MAX4665/MAX4666
(V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.)
(Note 2)
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = RON(MAX) - RON(MIN).
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7: Off-isolation = 20log10 [VCOM_ / (VNC_ or VNO_)], VCOM_ = output, VNC_ or VNO_ = input to off switch.
Note 8: Between any two switches.
Note 9: Leakage testing at single supply is guaranteed by testing with dual supplies.
_______________________________________________________________________________________ 5
5Ω, Quad, SPST,
CMOS Analog Switches
Typical Operating Characteristics
MAX4664/MAX4665/MAX4666
MAX4664 TOC03
MAX4664/5/6-02
ICOM = 10mA V+ , V- = ±15V
6.5 16
4.5 ICOM = 10mA
6.0 V+ = +5V
14
V+, V- = ±5V TA = +85°C
5.5 4.0
12
5.0
RON (Ω)
RON (Ω)
RON (Ω)
3.5 10
4.5
3.0 TA = +25°C 8
4.0
V+, V- = ±15V 6 V+ = +12V
3.5
V+, V- = ±20V 2.5
3.0 TA = -40°C 4 V+ = +24V
V+ = +36V
2.0 2
2.5
2.0 1.5 0
-20 -15 -10 -5 0 5 10 15 20 -15 -10 -5 0 5 10 15 0 3 6 9 12 15 18 21 24 27 30 33 36
VCOM (V) VCOM (V) VCOM (V)
MAX4664/5/6-05
MAX4664 TOC06
V+ = +12V V+ = +15V V+ = +15V
7.5
ICOM = 10mA TA = +85°C 10k V- = -15V 500 V- = -15V
7.0
1k 400
6.5
ON-LEAKAGE
LEAKAGE (pA)
Q (pC)
3.0 -200
0 2 4 6 8 10 12 -40 -25 -10 5 20 35 50 65 80 95 100 -20 -15 -10 -5 0 5 10 15 20
VCOM (V) TEMPERATURE (°C) VCOM (V)
ON/OFF TIMES vs. VCOM ON/OFF TIMES vs. VCOM ON/OFF TIMES vs. SUPPLY VOLTAGE
(DUAL SUPPLIES) (SINGLE SUPPLY) (DUAL SUPPIES)
180 300 150
MAX4664 TOC07
MAX4664 TOC08
MAX4664 TOC09
160 140
250
140 tON 130 tON
tON 120
120 200
tON, tOFF (ns)
110
100
150 100 tOFF
80
tOFF 90
60 tOFF 100
RL = 100Ω 80
RL = 100Ω
40 CL = 35pF CL = 35pF 70 RL = 100Ω
V+ = +15V 50
20 V+ = +12V 60 CL = 35pF
V- = -15V V- = GND VCOM = 10V
0 0 50
-10 -8 -6 -4 -2 0 2 4 6 8 10 0 2 4 6 8 10 12 14 10 11 12 13 14 15 16 17 18 19 20
VCOM (V) VCOM (V) V+ = -V (V)
6 _______________________________________________________________________________________
5Ω, Quad, SPST,
CMOS Analog Switches
Typical Operating Characteristics (continued)
MAX4664/MAX4665/MAX4666
(TA = +25°C, unless otherwise noted.)
ON/OFF TIMES vs. SUPPLY VOLTAGE ON/OFF TIMES vs. TEMPERATURE ON/OFF TIMES vs. TEMPERATURE
(SINGLE SUPPLY) (DUAL SUPPLIES) (SINGLE SUPPLY)
600 160 400
MAX4664 TOC12
MAX4664 TOC10
MAX4664 TOC11
RL = 100Ω RL = 100Ω
CL = 35pF 140 350 CL = 35pF
500 VCOM = 5V
VCOM = 5V tON
120 300 V+ = +12V
400 V- = GND tON
100 250
tOFF
300 80 200
60 150
200 RL = 100Ω
tON
40 CL = 35pF 100
100 VCOM = 10V tOFF
tOFF 20 V+ = +15V 50
V- = -15V
0 0 0
0 5 10 15 20 25 30 35 40 -60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100
V+ (V) TEMPERATURE (°C) TEMPERATURE (°C)
SUPPLY CURRENT
vs. TEMPERATURE FREQUENCY RESPONSE
10k 0
MAX4664 TOC14
MAX4664 TOC13
V+ = +15V ON-LOSS
-10
V- = -15V
1k
-20
ON-PHASE
-30
100 I+
-40
LOSS (dB)
I+, I- (pA)
10 I- -50
-60 OFF-ISOLATION
1
-70
-80 V+ = +15V
0.1
-90 V- = -15V
CROSSTALK 50Ω IN AND OUT
0.01 -100
-60 -40 -20 0 20 40 60 80 100 0.01 0.1 1 10 100
TEMPERATURE (°C) FREQUENCY (MHz)
_______________________________________________________________________________________ 7
5Ω, Quad, SPST,
CMOS Analog Switches
Pin Description
MAX4664/MAX4665/MAX4666
PIN
NAME FUNCTION
MAX4664 MAX4665 MAX4666
IN1, IN2,
1, 16, 9, 8 1, 16, 9, 8 1, 16, 9, 8 Logic-Control Digital Inputs
IN3, IN4
2, 15, 2, 15, 2, 15, COM1, COM2,
Analog Switch, Common Terminals
10, 7 10, 7 10, 7 COM3, COM4
NC1, NC2,
3,14, 11, 6 – – Analog Switch, Normally Closed Terminals
NC3, NC4
NO1, NO2,
– 3,14, 11, 6 – Analog Switch, Normally Open Terminals
NO3, NO4
– – 3, 6 NO1, NO4 Analog Switch, Normally Open Terminal
12 12 12 VL Logic-Supply Input
8 _______________________________________________________________________________________
5Ω, Quad, SPST,
CMOS Analog Switches
Above 5MHz, circuit board layout becomes critical, that is, designed with isolation in mind, but not using
MAX4664/MAX4665/MAX4666
and it becomes difficult to characterize the response of stripline or other special RF circuit techniques. For criti-
the switch independent of the circuit. The graphs cal applications above 5MHz, use the MAX440,
shown in the Typical Operating Characteristics were MAX441, and MAX442, which are fully characterized
taken using a 50Ω source and load connected with up to 160MHz.
BNC connectors to a circuit board deemed “average,”
MAX4664
MAX4665
+5V +15V MAX4666
t r < 20ns
SWITCH +3V t f < 20ns
VL V+ LOGIC
OUTPUT INPUT 50%
SWITCH V COM_ NO_ 0
COM_ VO
INPUT OR NC_
RL CL
100Ω 35pF t OFF
IN_
GND V- VO
LOGIC 0.9V0 0.9V0
SWITCH 0
INPUT OUTPUT
0 -15V t ON
REPEAT TEST FOR EACH SWITCH. FOR LOAD
CONDITIONS, SEE Electrical Characteristics.
LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
THAT HAVE THE OPPOSITE LOGIC SENSE.
RL
VO = VCOM (
RL + RON )
MAX4664
+5V +15V
MAX4665 ∆VO
MAX4666
VL V+
VO
RGEN
COM_ NC_ OR
VO
NO_ VIN
OFF OFF
V GEN CL ON
GND IN_ V-
ON
OFF OFF
-15V VIN
Q = (∆V O)(C L)
VIN = +3V VIN DEPENDS ON SWITCH CONFIGURATION;
INPUT POLARITY DETERMINED BY SENSE OF SWITCH.
_______________________________________________________________________________________ 9
5Ω, Quad, SPST,
CMOS Analog Switches
MAX4664/MAX4665/MAX4666
MAX4664
+15V +5V MAX4664
C MAX4665 C +15V +5V
MAX4665
MAX4666
MAX4666
SIGNAL SIGNAL V+
V+ VL 50Ω
GENERATOR 0dBm VL GENERATOR 0dBm N01
COM1
COM_
IN1 IN2
IN_ 0 or 2.4V
0 or 2.4V 0 or 2.4V
-15V -15V
MAX4664
+15V +5V MAX4664
+15V +5V MAX4665
C C MAX4665
MAX4666
MAX4666
V+ VL V+ VL
COM_ COM_
CAPACITANCE
METER
IN 0 or IN_ 0 or
CAPACITANCE 2.4V 2.4V
f = 1MHz
METER
NC_ OR NO_ NC_ OR NO_
f = 1MHz
GND V- C GND V- C
-15V -15V
Figure 6. Switch Off-Capacitance Test Circuit Figure 7. Switch On-Capacitance Test Circuit
10 ______________________________________________________________________________________
5Ω, Quad, SPST,
CMOS Analog Switches
Ordering Information (continued) Chip Information
MAX4664/MAX4665/MAX4666
TRANSISTOR COUNT: 108
PART TEMP. RANGE PIN-PACKAGE
MAX4665CSE 0°C to +70°C 16 Narrow SO
MAX4665CPE 0°C to +70°C 16 Plastic DIP
MAX4665ESE -40°C to +85°C 16 Narrow SO
MAX4665EPE -40°C to +85°C 16 Plastic DIP
MAX4666CSE 0°C to +70°C 16 Narrow SO
MAX4666CPE 0°C to +70°C 16 Plastic DIP
MAX4666ESE -40°C to +85°C 16 Narrow SO
MAX4666EPE -40°C to +85°C 16 Plastic DIP
Package Information
SOICN.EPS
______________________________________________________________________________________ 11
5Ω, Quad, SPST,
CMOS Analog Switches
Package Information (continued)
MAX4664/MAX4665/MAX4666
PDIPN.EPS
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.
WWW.ALLDATASHEET.COM
www.AllDataSheet.com
Free Download.
No Register.
www.AllDataSheet.com