Professional Documents
Culture Documents
B5A-0110-00 [J]
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry
Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
SiriusXM settings TUNE START*2 ON: Selected SmartFavorite channel starts playback from
1 Press and hold . the beginning of the song. ; OFF: Cancels.
2 Turn the volume knob to select [SIRIUS XM], then press the knob. SIGNAL LVL NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength
3 Turn the volume knob to make a selection (see the following table), then of the current received signal.
press the knob.
BUF USAGE 0% — 100% (0): Shows the memory usage for Replay
4 Repeat step 3 until the desired item is selected/activated or follow the
buffer.
instructions stated on the selected item.
5 Press to exit. SXM RESET YES: Resets stored channel and lock setting to default. ;
To return to the previous setting item, press . NO: Cancels.
*1 Displayed only when [USER DEFINED] is selected.
Default: XX *2 Available only if the connected SiriusXM Vehical Tuner is SXV200 or later that
CH LOCK To unlock settings: supports SmartFavorites.
1 Turn the volume knob to select a number.
2 Press to move to the entry position.
3 Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4 Press the volume knob to confirm.
CODE SET 1 Press the volume knob to enter [NEW CODE].
2 Turn the volume knob to select a number.
3 Press to move to the entry position.
4 Repeat steps 2 and 3 to enter a new 4-digit pass code.
5 Press the volume knob to confirm.
6 Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings from next time.
LOCK SET MATURE CH: Selects the SiriusXM-defined lock setting. ; USER DEFINED: Selects the
user-defined lock setting. ; OFF: Cancels.
CH EDIT*1 1 Turn the volume knob to select a category, then press the knob.
2 Turn the volume knob to select a channel you want to lock, then press the knob.
“L” appears in front of the channel number.
3 Press and hold to exit.
CH CLEAR*1 YES: Clears all the locked channels. ; NO: Cancels.
RECENT CALL 1 Press the volume knob to select a name or a phone number.
• “>” indicates call received, “<“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the volume knob to call.
PHONEBOOK 1 Press to select the desired letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• If the phone supports PBAP, the phonebook of the connected phone is automatically transferred to the
unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
DIAL NUMBER 1 Turn the volume knob to select a number (0 to 9) or character ( , #, Settings in memory
+).
2 Press to move the entry position.
Store a contact in memory
Repeat steps 1 and 2 until you finish entering the phone number. You can store up to 6 contacts into the number buttons (1 to 6).
3 Press the volume knob to call. 1 Press to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK], or
VOICE Speak the name of the contact you want to call or the voice command to [DIAL NUMBER], then press the knob.
control the phone functions. ( Make a call using voice recognition) 3 Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone
Make a call using voice recognition number.
1 Press and hold to activate the connected phone. 4 Press and hold one of the number buttons (1 to 6).
2 Speak the name of the contact you want to call or the voice “MEMORY P(selected preset number)” appears when the contact is
command to control the phone functions. stored.
• Supported Voice Recognition features vary for each phone. Refer to the To erase a contact from the preset memory, select [DIAL NUMBER] in step 2
instruction manual of the connected phone for details. and store a blank number.
• This unit also supports the intelligent personal assistant function of
iPhone. Make a call from memory
1 Press to enter Bluetooth mode.
Delete a contact 2 Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
1 Press to enter Bluetooth mode.
“NO PRESET” appears if there is no contacts stored.
2 Turn the volume knob to select [RECENT CALL], then press the knob.
3 Turn the volume knob to select a contact.
4 Press and hold to enter delete mode. Bluetooth mode settings
5 Turn the volume knob to select [DELETE] or [DELETE ALL], then press 1 Press and hold .
the knob.
2 Turn the volume knob to select [BLUETOOTH], then press the knob.
DELETE: Selected name or phone number in step 3 is deleted.
3 Turn the volume knob to make a selection ( 18), then press the
DELETE ALL: All names or phone numbers in [RECENT CALL] in step 2 is
knob.
deleted.
4 Repeat step 3 until the desired item is selected/activated or follow
6 Turn the volume knob to select [YES], then press the knob. the instructions stated on the selected item.
• To return to the previous setting item, press . 5 Press to exit.
• Not applicable for mobile phone that supports PBAP.
To return to the previous setting item, press .
PRO EQ (For KD-AR865BTS) SUB.W PHASE *5 REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
1 USER1/ USER2: Select a preset name. output to be in line with the speaker output for optimum performance.
2 BASS / MID BASS / MID / MID HIGH / HIGH: Select a sound tone. (Selectable only if a setting other than [THROUGH] is selected for
3 Adjust the sound elements of the selected sound tone. [SUB.W LPF].)
BASS Frequency: 63/ 80/ 100/ 125 HZ (Default: 80 HZ
HPF (For KD-AR865BTS)
Level: –10 to +10 00
OFF: All signals are sent to the front/rear speakers. ; LOW 100HZ /
Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 Q1.25)
MID 120HZ / HIGH 150HZ: Audio signals with frequencies lower than
MID BASS Frequency: 200/ 250/ 315/ 400 HZ (Default: 250 HZ
100 Hz/ 120 Hz/ 150 Hz are cut off from the front/rear speakers.
Level: –10 to +10 00
Q: Q1.0/ Q1.25/ Q1.5/ Q2.0 Q1.25) FADER R06 — F06 (00): Adjusts the front and rear speaker output balance.
MID Frequency: 630/ 800 HZ/ 1.0/ 1.25 KHZ (Default: 800 HZ BALANCE *8 L06 — R06 (00): Adjusts the left and right speaker output balance.
Level: –10 to +10 00
Q: Q0.75/ Q1.0/ Q1.25/ Q2.0 Q1.0) VOL ADJUST –05 — +05 (00): Presets the volume adjustment level of each source
MID HIGH Frequency: 2.0/ 2.5/ 3.15/ 4.0 KHZ (Default: 2.5 KHZ (compared to the FM volume level). Before adjustment, select the source
Level: –10 to +10 00 you want to adjust. (“VOL ADJ FIX” appears if FM is selected.)
Q: Q0.75/ Q1.0/ Q1.25/ Q2.0 Q1.0) AMP GAIN LOW POWER: Limits the maximum volume level to 30. (Select if the
HIGH Frequency: 6.3/ 8.0/ 10.0/ 12.5 KHZ (Default: 8.0 KHZ maximum power of each speaker is less than 50 W to prevent damaging
Level: –10 to +10 00 the speakers.) ; HIGH POWER: The maximum volume level is 50.
Q: Q0.75/ Q1.0/ Q1.25/ Q2.0 Q1.0)
D.T.EXP ON: Creates realistic sound by compensating the high-frequency
AUDIO (Digital Track components and restoring the rise-time of the waveform that are lost in
BASS BOOST +01 / +02: Selects your preferred bass boost level. ; OFF: Cancels. Expander) audio data compression. ; OFF: Cancels.
LOUD 01 / 02: Boosts low or high frequencies to produce a well-balanced sound at SPK/PRE OUT Selects the appropriate setting to get the desired output. ( 22).
low volume. ; OFF: Cancels. *5 Displayed only when [SUB.W] is set to [ON].
SUB.W SPK-OUT *6 00 to +06 (+03): Adjusts the output level of the subwoofer *6 Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W]. ( 22)
LEVEL *5 connected via speaker lead. ( 31, 32) *7 For unit with 3-pair lineout terminals: Displayed only when [SPK/PRE OUT] is set to
[REAR/REAR] or [SUB.W/SUB.W]. ( 22)
PRE-OUT *7 –08 to +08 (00): Adjusts the output level of the subwoofer For unit with 2-pair lineout terminals: Displayed only when [SPK/PRE OUT] is set to
connected to the lineout terminals (SW or REAR/SW) [REAR/SUB.W] or [SUB.W/SUB.W]. ( 22)
through an external amplifier. ( 31, 32) *8 This adjustment will not affect the subwoofer output.
SUB.W *7 ON / OFF: Turns on or off the subwoofer output.
SUB.W LPF *5 THROUGH: All signals are sent to the subwoofer. ; LOW 55HZ / MID 85HZ /
HIGH 120HZ: Audio signals with frequencies lower than 55 Hz/ 85 Hz/
120 Hz are sent to the subwoofer.
CD / USB / iPod
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections. turn on or does not work. • Detach and reset the iPod/iPhone using hard reset.
“MISWIRING CHECK Turn the power off, then check to be sure the terminals of Correct characters are not This unit can only display uppercase letters, numbers,
General
WIRING THEN PWR ON” the speaker wires are insulated properly. Turn the power displayed. and a limited number of symbols.
appears. on again.
• Sound cannot be heard • Reconnect the Android device.
“PROTECTING SEND Send the unit to the nearest service center. during playback. • If in [AUDIO MODE], launch any media player application
SERVICE” appears. • Sound output only from on the Android device and start playback.
the Android device. • If in [AUDIO MODE], relaunch the current media player
Source cannot be selected. Check the [SRC SELECT] setting. ( 4)
application or use another media player application.
• Radio reception is poor. • Connect the antenna firmly. • Restart the Android device.
Radio
• Static noise while • Pull the antenna out all the way. • If this does not solve the problem, the connected Android
listening to the radio. device is unable to route the audio signal to unit. ( 24)
Disc cannot be ejected. Press and hold to forcibly eject the disc. Be careful not Cannot playback at [AUTO • Make sure JVC MUSIC PLAY APP is installed on the
to drop the disc when it is ejected. MODE]. Android device. ( 5)
• Reconnect the Android device and select the appropriate
ANDROID
“IN DISC” appears. Make sure nothing is blocking the loading slot when you control mode. ( 6)
eject the disc. • If this does not solve the problem, the connected Android
device does not support [AUTO MODE]. ( 24)
“PLEASE” and “EJECT” Press , then insert the disc correctly.
appear alternately. “NO DEVICE” or “READING” • Switch off the developer options on the Android device.
keeps flashing. • Reconnect the Android device.
Playback order is not as The playback order is determined by the file name (USB)
CD / USB / iPod
“SEARCH ERR”
“CANNOT PLAY” flashes • Check whether the connected device is compatible with this
and/or connected device unit and ensure the files are in supported formats. ( 24) “CHK DEVICE” Check the Pandora application on your device.
cannot be detected. • Reattach the device. “NO SKIPS” The skip limit has been reached.
SiriusXM® Radio
“LICENSE ERR” You try to access from a country which Pandora is not “CHK ANTENNA” Check the antenna and its connection are in good condition.
deliverable.
“CHECK TUNER” Make sure the SiriusXM Vehicle Tuner is connected to the
Station cannot be selected. If “Explicit Content” in [Account Settings] is checked in unit.
the web version of iHeartRADIO, custom stations become
unavailable. “NO SIGNAL” Make sure the antenna is mounted outside the vehicle.
“CREATE ERR” Custom station name creation is unsuccessful. “SUBSCRIPTION Your subscription is updated. Press the volume knob to
UPDATED – PRESS continue.
“SAVE ERROR” Addition to the favorite category failed. ENTER TO CONTINUE.”
“DISCONNCTED” Check the connection to the device. “CODE ERROR” Make sure you have entered the correct pass code. ( 13)
“NO SKIPS” The skip limit has been reached. Retry later. “NO CONTENT” There is insufficient content to start TuneScan.
“NO STATIONS” No stations are found.
iHeartRadio
Tuner
Frequency Response (±3 dB) 30 Hz — 15 kHz
audio player cannot be supports Audio/Video Remote Control Profile (AVRCP).
controlled. (Refer to the instructions of your audio player.) Signal-to-Noise Ratio (MONO) 64 dB
• Disconnect and connect the Bluetooth player again. Stereo Separation (1 kHz) 40 dB
“PAIRING FULL” The number of registered devices has reached its limit. AM Frequency Range 530 kHz — 1 700 kHz (10 kHz step)
Retry after deleting an unnecessary device. ( 18, 531 kHz — 1 611 kHz (9 kHz step)
DELETE PAIR)
Bluetooth®
CD player
the device supports the function you have tried. Total Harmonic Distortion (1 kHz) 0.01 %
“H/W ERROR” Reset the unit and try the operation again. If “H/W ERROR” Signal-to-Noise Ratio (1 kHz) 105 dB
appears again, consult your nearest service center.
Dynamic Range 90 dB
“BT ERROR PLS UPDATE” Update the Bluetooth firmware. ( 4)
Channel Separation 85 dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
AAC Decode AAC-LC “.m4a” files
USB Standard USB 1.1, USB 2.0 (Full speed) Maximum Output Power 50 W × 4 or
50 W × 2 + 50 W × 1 (Subwoofer = 4 Ω)
Compatible Devices Mass storage class
Full Bandwidth Power 22 W × 4
File System FAT12/ 16/ 32
(at less than 1 % THD)
Maximum Supply Current DC 5 V 1 A
Audio
USB
General
Version Bluetooth Ver.2.1+EDR/ Bluetooth 3.0 Operating Temperature Range 0°C to +40°C
Frequency Range 2.402 GHz — 2.480 GHz Installation Size (W × H × D) 182 mm × 53 mm × 158 mm
(7-3/16" × 2-1/8" × 6-1/4")
Output Power +4 dBm (MAX), 0 dBm (AVE) Power Class 2
Weight 1.2 kg (2.65 lbs)
Bluetooth
Microphone input
jack ( 14)
Antenna terminal
Factory wiring To the steering
harness (vehicle) Light blue/yellow
wheel remote STEERING (B) Trim plate
control adapter WHEEL
REMOTE