Professional Documents
Culture Documents
215x70 mm einfügen
Operating Instructions
OM 904 LA – OM 906 LA – OM 926 LA
EU Level III A (EU 97/68/EC)
EPA TIER 3 (US EPA 40 CFR Part 89)
Symbols
* Optional equipment
G Warning
H Environmental note
i Tip
Action required
Continuation symbol
5
Introduction
Operating safety
6
Introduction
Operating safety
Correct use
Risk of accident G The engine is only designed for installation
Work incorrectly carried out on electronic in accordance with the specifications de-
components and their software could impair fined in the contract.
the functioning of these components. Since The manufacturer of the end product is
the electronic systems are networked, this personally responsible for the complete
might also affect systems that have not system, and in particular for the correct in-
been modified. stallation and compatibility of this engine
For this reason, always have work on, or with the rest of the system.
modifications to, electronic components The engine must not be modified.
carried out at a qualified specialist work- DaimlerChrysler accepts no responsibility
shop. for damage caused as the result of modifi-
DaimlerChrysler recommends that you use cations.
a Mercedes-Benz Service Centre for this Correct use of the engine includes adher-
purpose as it has the necessary specialist ing to these Operating Instructions, adher-
knowledge and tools for the work required. ing to the maintenance intervals and
performing maintenance work correctly in
accordance with these Operating Instruc-
tions.
7
8
At a glance
OM 904 LA overview
OM 906 LA/OM 926 LA overview
Location of sensors 1
Engine number
9
At a glance
OM 904 LA overview
10
At a glance
OM 904 LA overview
11
At a glance
OM 904 LA overview
12
At a glance
OM 904 LA overview
1 Starter motor 1
2 Flywheel housing
3 Exhaust gas turbocharger
4 Exhaust manifold
5 Charge-air housing
6 Charge-air pipe connection from the
intercooler
7 Charge-air pipe connection to the
intercooler
8 Oil filter
9 Alternator
13
At a glance
OM 906 LA/OM 926 LA overview
14
At a glance
OM 906 LA/OM 926 LA overview
15
At a glance
OM 906 LA/OM 926 LA overview
16
At a glance
OM 906 LA/OM 926 LA overview
1 Starter motor 1
2 Flywheel housing
3 Turbocharger with wastegate valve
4 Exhaust manifold
5 Charge-air housing
6 Charge-air pipe connection from the
intercooler
7 Charge-air pipe connection to the
intercooler
8 Oil filter
9 Alternator
17
At a glance
Location of sensors
18
At a glance
Location of sensors
19
At a glance
Engine number
20
Before commissioning
General information
Transport and installation
21
Before commissioning
General information
Type designation
OM 9XX L A
2
OM Oil engine
(diesel engine)
9XX Engine model
L Intercooler
A Exhaust gas
turbocharger
22
Before commissioning
General information
23
Before commissioning
General information
Engine brake*/constantly-open i
throttle valves* Hydraulic constantly-open throttle
To increase the braking power, the engine valves
2 can be equipped with an exhaust brake The constantly-open throttle valves are
valve on the exhaust gas turbocharger in not actuated in the lower engine speed
conjunction with constantly-open throttle range between 900 and 1,300 rpm or if
valves on the cylinders. the engine oil temperature is less than
Whereas exhaust gas backpressure, acting 40 °C.
through the exhaust brake valves, can be Observe these restrictions during oper-
used to increase the braking power, the ation.
constantly-open throttle valves cause a
reduction of compression in the power
stroke (3rd stroke), leaving compression
(2nd stroke) practically unaffected.
Constantly-open throttle valves on the
The constantly-open throttle valves are 4-cylinder engine
valves in the cylinder head. When open,
they connect the combustion chamber to When the engine brake is engaged, the
the exhaust duct, which generates the re- constantly-open throttle valves are opened
quired decompression in the power stroke. pneumatically on the 4-cylinder engine and
hydraulically on the 6-cylinder engine. At
the same time, the exhaust brake valve on
the exhaust gas turbocharger is closed.
24
Before commissioning
General information
The engine brake is controlled by the FR Flame-start system* A flame glow plug is fitted in the charge
(drive control) unit ( page 29) or the pressure pipe of the intercooler. Fuel can
The flame-start system is a cold-start aid
ADM. be ignited at this flame glow plug. The fuel
for when ambient temperatures are low. It
is supplied to the flame glow plug via a so- 2
The engine brake always remains deacti- reduces the emissions of white smoke
vated at engine speeds of below 900 rpm lenoid valve with a dosing nozzle.
once the engine has been started. The
to prevent the engine from stalling. The en- starter motor and battery are also protect-
gine brake is also automatically deactivat- ed as a result of the shorter start-up time.
ed if the position sensor is triggered (e.g. if
the accelerator pedal is depressed).
i
In the emergency running program
(constant engine speed), the engine
brake can only be activated in overrun
mode at an increased engine speed.
The engine brake is automatically deac-
tivated again once a constant engine
speed has been reached.
Flame-start system
25
Before commissioning
General information
i
For operation at low ambient tempera-
tures, see also the “Diesel fuels”
( page 59) and “Coolant”
( page 64) sections.
26
Before commissioning
General information
Telligent® engine system MR (engine control) unit (mounted on The MR (engine control) unit processes
the engine) data from the drive control unit or the
The engine has a fully electronic control ADM, indicating for example the position
system, which, in addition to the engine The MR (engine control) unit is mounted on
of the position sensor (accelerator pedal),
and associated sensors, also comprises: the left-hand side of the engine. 2
the engine brake* or engine start/stop,
an MR (engine control) unit and etc.
an FR (drive control) unit and/or other
vehicle-specific control units, e.g. ADM
Both are interconnected via a CAN (Con-
troller Area Network) line, on which all the
necessary data/information is ex-
changed.
The engine control monitors itself as well
as the engine. A safety and emergency run-
ning program is selected automatically,
depending on the malfunctions/system
failures that occur ( page 37).
27
Before commissioning
General information
28
Before commissioning
General information
FR (drive control) unit or ADM (mounted The FR (drive control) unit or the ADM re- If the Telligent® engine system detects a
on the equipment) ceive data from the: fault, this is stored in the control units as a
fault code, which can then be read using
The engine can be adapted to meet various operator (position of the position sen-
appropriate diagnostic equipment (STAR
application-specific requirements by sor, engine start/stop) 2
DIAGNOSIS or minidiag2).
means of the drive control unit or adapta- engine brake switch*
tion module (ADM). In addition, the electronics warning lamp
other systems (e.g. acceleration skid lights up.
control system)
MR (engine control) unit (e.g. oil pres-
i
sure and coolant temperature) The DaimlerChrysler diagnostic equip-
ment can be connected to the equip-
This data is used to determine the instruc- ment-mounted 14-pin diagnostic
tions for engine control (MR control unit), socket or using the EU-compliant serv-
which are then sent to the engine control ice connector. This equipment can be
on the CAN line. used to read both the malfunction
The FR (drive control) unit or the ADM con- memory and the stored engine data.
FR (drive control) unit
trols various displays, e.g. the electronics
warning lamp, the engine brake* and the
The FR (drive control) unit or the ADM constantly-open throttle valves*.
stores a range of application-specific data,
such as idling speed, maximum working
speed or speed limitation.
29
Before commissioning
General information
30
Before commissioning
Transport and installation
Transport and installation
Transport
Risk of injury G 2
The engine can break loose and cause injury
to persons by overturning or falling.
Only lift the engine by the appropriate
lifting points on the engine.
Only use transport equipment that
has been approved for use by
DaimlerChrysler.
Only lift and transport the engine in the
installation position. Observe the maxi-
mum angle of 30° when lifting the en-
gine in or out of the machine or vehicle. Lifting point, flywheel-side Lifting point, belt-side
31
Before commissioning
Transport and installation
Installation
The engine is only designed for installation
in accordance with the specifications de-
2 fined in the contract.
The manufacturer of the end product is
personally responsible for the complete
system, and in particular for the correct in-
stallation and compatibility of this engine
with the rest of the system.
Observe the “Correct use” ( page 7) and
“Conversion parts and modifications to the
engine” ( page 36) sections.
The “Technical data” section of these Op-
erating Instructions contains information
required for the installation of the engine.
Please consult a Mercedes-Benz Service
Centre if you have any questions.
i
The engine is filled with engine oil at
the factory.
32
Safety
Safety precautions
Staff qualifications
Conversion parts and modifications to the engine
Safety/emergency running programs
Genuine Mercedes-Benz parts
33
Safety
Safety precautions
34
Safety
Staff qualifications
Staff qualifications
Engines may only be operated, maintained
Risk of accident G and repaired by trained personnel instruct-
ed and authorised by the operator.
Maintenance and repair work to the engine
The responsibilities for operation, mainte-
carried out incorrectly can impair both its
nance and repairs must be assigned by the
correct operation and safety, leading to ac-
operator.
cidents and personal injury. 3
The legal minimum age for carrying out the
Always have work on or modifications to the
work specified above must be observed.
engine carried out at a qualified specialist
workshop which has the necessary special-
ist knowledge and tools for the work re-
quired.
Mercedes-Benz recommends that you use a
Mercedes-Benz Service Centre for this pur-
pose.
35
Safety
Conversion parts and modifications to the engine
!
Tampering with the fuel-injection sys-
tem and engine electronics may affect
the performance and emission levels of
the engine. It would no longer be possi-
ble to guarantee compliance with fac-
tory settings or legal environmental
protection conditions.
36
Safety
Safety/emergency running programs
Safety/emergency running programs
The engine is equipped with an electronic i
control system that monitors both the en- Risk of accident G The DaimlerChrysler diagnostic equip-
gine and itself (self-diagnostic system).
ment can be connected to the equip-
Maintenance and repair work to the engine
If a malfunction is detected, it is immedi- ment-mounted 14-pin diagnostic
carried out incorrectly can impair both its
ately evaluated and one of the following socket or using the EU-compliant serv-
correct operation and safety, leading to ac-
measures is automatically initiated: ice connector. This equipment can be
cidents and personal injury. 3
If the engine is running, a malfunction used to read both the malfunction
Always have work on or modifications to the memory and the stored engine data.
is indicated by the electronic system
engine carried out at a qualified specialist
warning lamp lighting up.
workshop which has the necessary special-
The fault codes may be shown on a dis- ist knowledge and tools for the work re-
play on vehicles with the Telligent® quired.
engine system (vehicle diagnostics Mercedes-Benz recommends that you use a
system). Mercedes-Benz Service Centre for this pur-
The engine is switched to the appropri- pose.
ate back-up function for continued (but
restricted) operation (e.g. constant
emergency running speed).
37
Safety
Genuine Mercedes-Benz parts
Make sure that the replacement parts are Additional information about recommend-
suitable for your engine. The general oper- ed conversion parts and accessories and
ating permit will, in many countries, be in- permissible technical modifications is
validated by parts that lead to an engine/ available from any Mercedes-Benz Service
vehicle modification that: Centre.
changes the type of machine/ vehicle Always quote the engine number and mod-
3 approved in the General Operating Per- el designation when ordering genuine
mit parts. You will find the numbers on the en-
gine plate ( page 20) and on the engine
poses a potential risk to road users, or
data card ( page 22).
causes a deterioration in exhaust gas
emission levels or noise levels
The use of non-approved parts can jeop-
ardise safety.
Environmental note H
To combine cost-effective repairs with recy-
cling, Mercedes-Benz also offers recondi-
tioned engines and parts. These are of the
same quality and have the same warranty as
new parts.
38
Operation
Starting the engine for the first time
Monitoring engine operation
Stopping the engine
Winter operation
Cleaning/protective treatment
Service products
39
Operation
Starting the engine for the first time
40
Operation
Starting the engine for the first time
Refuelling i
Use summer or winter fuel depending on Bleed the heated fuel prefilter with wa-
Risk of explosion G
the season. See also “Diesel fuels” ter separator* mounted on the vehicle
Gases leaking from batteries may explode
( page 59). or machine with the integrated hand
and therefore cause injury.
pump.
! Fire, naked flames, smoking and sparks are
When refuelling do not allow water to Checking the batteries therefore not permitted in the vicinity of the
enter the tank, contaminating the fuel. batteries.
Bleeding the fuel system Risk of injury G Only use batteries that have been correctly 4
If the fuel system is run dry, the system will filled and maintained. Grease the battery
The acid contained in batteries burns skin
be bled the next time the engine is started terminals with acid-proof grease (battery
and eyes on contact.
after refuelling. Automatic continuous terminal grease).
Do not allow acid to come into contact
bleeding takes place in the filter. with your skin, eyes or clothing. i
i Wear suitable protective clothing, as The cable cross-sections are depend-
The battery must be sufficiently battery acid can burn through normal ent on the distance between the bat-
clothing. In addition, protective gloves tery and the starter motor.
charged during the starting procedure
and safety goggles should be worn.
to ensure that the fuel system can be
bled. Rinse acid splashes off immediately with
clean water and consult a doctor if nec-
essary.
41
Operation
Starting the engine for the first time
42
Operation
Starting the engine for the first time
43
Operation
Starting the engine for the first time
44
Operation
Starting the engine for the first time
45
Operation
Starting the engine for the first time
To start the engine using the START button If the vehicle is equipped with a flame-start !
on the machine or on the engine: system* or grid heater*: The charge current indicator lamp and
Wait until the flame-start system*/ electronic system warning lamp must
grid heater* indicator lamp goes out. go out after the engine has started. If
they remain lit, this indicates that there
Start the engine within 30 seconds us-
is a malfunction; ( see page 48) and
ing the START button on the machine
( page 49).
or engine.
!
4 Keep the engine running at idling speed
until an oil pressure reading is dis-
played (do not rev the engine). If no oil
pressure is displayed after approxi-
mately 10 seconds, switch off the en-
gine. Determine the cause
( page 48).
Start/stop buttons If necessary, interrupt the starting pro-
cedure after a maximum of 20 seconds,
1 STOP button and then repeat after approximately
2 START button 1 minute.
On the engine: press START button 2
on the engine.
Monitor the oil pressure gauge immedi-
ately after starting the engine.
46
Operation
Starting the engine for the first time
i i
Flame-start system* Grid heater*
Depending on the ambient tempera- The grid heater is activated by the FR or
ture, the flame-start system* indicator ADM control unit. The preglow time de-
lamp lights up: pends on the temperature of the cool-
for approximately 2 seconds (func- ant and charge air and is approximately
30 seconds. The indicator lamp lights
tion check, flame-start system not
up during the preglow time and goes
in operation)
out when it is finished. 4
for up to approximately 20 seconds
At temperatures well below zero, do
(maximum preglow time)
not place the cold engine under full
If the flame-start system* indicator load immediately.
lamp does not go out after 20 seconds,
there is a malfunction.
At temperatures well below zero, do
not place the cold engine under full
load immediately.
47
Operation
Monitoring engine operation
48
Operation
Monitoring engine operation
Telligent® engine system Each malfunction is stored in the system Flame-start system*
with its own fault code. Temporary faults
There is a malfunction in the flame-start
are also stored.
system if:
Fault codes can be read using
the flame-start system* indicator lamp
DaimlerChrysler diagnostic equipment
lights up while the engine is running
(STAR DIAGNOSIS or minidiag2 tester)
( see page 29). If the electronic system the flame-start system indicator lamp
warning lamp lights up while the engine is does not go out within 20 seconds of
running, read or determine the fault code. the engine being started
4
Have the flame-start system checked at a
specialist workshop. DaimlerChrysler rec-
Electronic system warning lamp ommends that you use a Mercedes-Benz
The electronic system warning lamp must Service Centre for this purpose as it has
go out after the engine has started. the necessary specialist knowledge and
tools for the work required.
If the warning lamp does not go out or if it
lights up while the engine is running, there
is a malfunction in the Telligent® engine
system.
49
Operation
Monitoring engine operation
i Grid heater*
The flame-start system is automatically !
deactivated if:
The grid heater is malfunctioning if the
the engine is not started within grid heater indicator lamp flashes.
30 seconds of the flame-start sys-
tem indicator lamp going out
the engine is started when the
flame-start indicator lamp is lit
4 the charge current indicator lamp
does not go out while the engine is
running
the engine reaches a temperature
at which the flame-start system is
Flame-start system*/grid heater*
no longer required
(example)
50
Operation
Stopping the engine
Stopping the engine
Run the engine at idling speed for one Press STOP button 1 on the engine or
or two minutes without load after oper- on the machine-mounted engine shut-
ation at full power or a high coolant down facility.
temperature.
!
Stop the engine immediately if any of
the following occur:
significant drops or fluctuations in
oil pressure
4
falling power output and engine
speed with the position sensor
(accelerator pedal) in the same
position
large amounts of exhaust smoke
emitted from the exhaust
significant increases in coolant and
oil temperature
51
Operation
Winter operation
Fuel
Risk of explosion G Risk of injury G
The use of liquid or gaseous starting aids The cooling system is pressurised. Hot cool-
Risk of fire G can cause explosions. This may result in se- ant can escape under pressure when the
vere injuries. cooling system is opened and scald your
Fuel is highly flammable. For this reason, Do not use liquid or gaseous starting skin and eyes.
avoid fire and naked flames and refrain from aids, such as ether or Startpilot to start Only open the cooling system at coolant
4 smoking when handling fuel. the engine. temperatures below 90 °C.
Unscrew the cap slowly and release any
Use cold-resistant diesel fuel Engine oil excess pressure completely before
( see page 59). opening the cap fully.
When changing the engine oil, select an
engine oil that is compatible with the SAE Wear suitable protective gloves, protec-
classification and the ambient tempera- tive clothing and safety goggles when
tures expected during the period of use handling coolant.
( see page 63).
52
Operation
Winter operation
Batteries
Risk of poisoning G Have the batteries serviced and recharged Risk of explosion G
more frequently during the cold months of
There is a risk of poisoning if coolant is swal- Gases leaking from batteries may explode
the year.
lowed. and therefore cause injury.
Never swallow coolant. Fire, naked flames, smoking and sparks are
Risk of injury G therefore not permitted in the vicinity of the
Never store coolant in containers nor-
mally used for beverages. batteries.
The acid contained in batteries burns skin
Store coolant out of the reach of chil- and eyes on contact. 4
dren. Careful maintenance and low power con-
Do not allow acid to come into contact sumption will help to maintain the full bat-
with your skin, eyes or clothing.
Check the antifreeze protection properties tery charge. Starting capacity is greatly
Wear suitable protective clothing, as reduced in cold weather; at –10 °C, for ex-
of the coolant in good time and increase
battery acid can burn through normal ample, it is only around 60% of normal ca-
the antifreeze/corrosion inhibitor concen- clothing. In addition, protective gloves
tration if necessary ( see page 64). pacity. If the engine is not used for a long
and safety goggles should be worn.
period of time, store the batteries in a
Rinse acid splashes off immediately with heated place if possible. Ensure good ven-
clean water and consult a doctor if nec- tilation when recharging.
essary.
53
Operation
Cleaning/protective treatment
54
Operation
Cleaning/protective treatment
55
Operation
Cleaning/protective treatment
Degreasing
Risk of poisoning G Fill the cooling system with a 5% solu-
tion of water and a mild alkaline clean-
There is a risk of poisoning if coolant is swal-
er, e.g. “P3 Croni” (50 g cleaning agent
lowed.
per litre of water).
Never swallow coolant.
Warm the engine up to approximately
Never store coolant in containers nor- 80 °C (coolant thermostat starts to
mally used for beverages.
open) at a moderate engine speed and
Store coolant out of the reach of chil- allow it to run for approximately 5 min-
4 dren. utes longer.
Switch off the engine and allow it to
Drain off coolant when the engine is
cool to approximately 50 °C.
cold ( page 92).
Drain off the cleaning solution com-
If a heater is connected to the cooling
pletely.
system, open the regulating valves ful-
ly. Immediately afterwards, fill the cooling
system with clean water, warm up the
engine, and drain off the water after
5 more minutes. Then repeat the pro-
cedure a second time.
Fill the cooling system with new cool-
ant ( page 93) and observe the notes
in the “Coolant” section ( page 64).
56
Operation
Cleaning/protective treatment
Protective treatment i
The special protection required will de- Information is available from any
pend on the length of time the engine is to Mercedes-Benz Service Centre. Con-
be out of use as well as the prevailing am- sultation is strongly recommended.
bient conditions in the place where the en-
gine is to be located or stored.
After cleaning the engine, store it in as dry
and well-ventilated an area as possible. If
this is not possible, the intervals for carry- 4
ing out regular protective measures must
be halved.
It is essential that the engine be protected
from direct contact with water (rain/spray
water).
No anti-corrosion measures are required if
the engine is to be out of use for less than
12 months and the above storage condi-
tions are observed.
Special protective treatment measures are
required if the engine is to be out of use for
more than 12 months or there are ex-
ceptional storage and transport condi-
tions.
57
Operation
Service products
58
Operation
Service products
Diesel fuels Diesel fuels in extremely cold weather If summer diesel fuel or less cold-resistant
winter diesel fuel is used, only add a specif-
Only use commercially available diesel fu- At low outside temperatures, paraffin sep-
ic quantity of flow improver or kerosene
els (EN 590). The use of other fuels is sub- aration may affect the flow characteristics
suitable for the outside temperatures.
ject to official approval from of diesel fuel.
DaimlerChrysler. To prevent operating problems (e.g. as a
Fuel additives are not necessary. The use result of blocked filters), diesel fuels with Risk of explosion G
of fuel additives may limit your warranty improved cold flow properties are available
Adding petrol reduces the flash point for the
entitlement. on the market in the winter months. Devia-
diesel fuel and increases the risk of fire and
tions are possible in individual countries
If diesel fuels with a sulphur content of explosion. 4
and in the transition between the cold and
more than 0.3% by weight are used, the en- warm seasons. In Germany, special cold- For this reason, do not mix petrol with
gine oil must be changed at shorter inter- resistant winter-grade diesel fuels are the diesel fuel under any circumstances.
vals. Observe the information in the available that ensure reliable operation For this reason, you must avoid fire, na-
Maintenance Booklet. down to approximately –20 °C. Winter- ked flames and sparks, and refrain from
Filling the vehicle’s fuel tank from drums or grade diesel fuel can normally be used smoking when handling these service
canisters may introduce impurities into the without risk of malfunctions at the outside products.
fuel system. This can lead to fuel system temperatures to be expected in the coun- Observe the relevant safety regulations.
malfunctions. The fuel must therefore be try of sale.
filtered when filling the tank.
The fuel must not be mixed with water un-
der any circumstances.
59
Operation
Service products
! Kerosene
There is a risk of serious engine dam- Add only as much as is required for the Risk of explosion G
age if petrol is mixed with diesel. prevailing outside temperatures. The addi-
Adding kerosene reduces the flash point of
tion of 5% by volume of kerosene improves
For this reason, do not mix petrol with the fuel, increasing the risk of fire and explo-
the cold-resistance of diesel fuel by ap-
the diesel fuel under any circumstanc- sion.
proximately 1 °C. Do not exceed the max-
es. For this reason, avoid fire and naked
imum mixing ratio of 50% kerosene.
flames and refrain from smoking when
Mix the additive with the diesel fuel in good ! handling these service products.
4 time, before the flow properties of the die-
There is a risk of engine damage if ker- Only mix kerosene with diesel in the fuel
sel are affected by paraffin separation.
osene is permanently mixed with die- tank.
Malfunctions caused by paraffin separa-
sel. First add the kerosene and then the
tion can only be remedied by warming up
It is therefore not permissible to mix diesel fuel.
the entire fuel system.
kerosene with diesel on a permanent Observe the relevant safety regulations.
Do not mix additives with special cold-re-
basis.
sistant winter diesel fuels as the cold-flow
properties of the fuel could deteriorate. Run the engine for a while to ensure that
Flow improvers the additive reaches all parts of the fuel
system.
The effectiveness of flow improvers cannot
be guaranteed with all fuels. Observe the
manufacturer’s recommendations. Infor-
mation about approved flow improvers is
available from any Mercedes-Benz Service
Centre.
60
Operation
Service products
FAME fuels ! !
The 900 series engines are suitable for op- The fuel filter and engine oil filter Only use FAME fuels complying
eration with FAME fuel (bio-diesel fuel) must be replaced approximately with EN 14214. Special additives
complying with EN 14214. 200 operating hours following con- are not permitted. The use of fuels
version to FAME fuel. that do not comply with the
The following effects arise from operation EN 14214 standard or the addition
with FAME fuel: The oil and fuel filter must be re-
placed with every engine oil of special additives may lead to
slight increase in fuel consumption change. malfunctions or damage to the en-
gine.
slightly reduced engine power output FAME fuels reduce the service life
FAME fuels attack painted surfaces. 4
of a conventional fuel filter.
increased white smoke development Immediately rinse off the FAME fuel
after a cold engine start The engine oil change and filter re-
with water before it has time to re-
placement intervals are significant-
Before operation with any FAME fuel, a act with the paintwork. Use only en-
ly reduced. The engine oil change
Mercedes-Benz Service Centre must be gine oils complying with
and filter replacement must be car-
consulted to clarify the precise proce- Mercedes-Benz Specifications for
ried out at least once a year.
dures for use (e.g. maintenance intervals). Service Products sheet number
228.5 or 228.3.
Observe the following points for operation
with FAME fuel:
61
Operation
Service products
! !
FAME fuels may cause components Based on negative experiences, Environmental note H
in the fuel system to stick if the en- DaimlerChrysler does not accept
the use of pure vegetable oils as an If you operate your vehicle using bio-diesel
gine is left switched off for long pe-
alternative to diesel or FAME fuels. fuel, please consult your disposal firm as to
riods. For this reason, always use
The use of pure vegetable oils can whether the engine oil must be collected
up the amount of FAME fuel remain-
lead to engine damage arising from separately. Not all manufacturers of rere-
ing in the fuel tank and refuel with
coking and oil sludge forming as fined products (lubricants manufactured
conventional diesel fuel before the
well as deposits in combustion from used engine oils) are able to process
engine is switched off for long peri-
4 chambers. engine oil contaminated with bio-diesel fuel.
ods. Run the engine for at least one
hour before the vehicle is parked Observe the special notes and national reg-
up. ulations on the disposal of engine oils. Infor-
The quality of hoses adjacent to the mation is available from any qualified
engine, and connected either to the specialist workshop or Mercedes-Benz Serv-
vehicle or machine, must satisfy the ice Centre.
requirements of FAME fuels.
62
Operation
Service products
Mercedes-Benz does not accept warranty FAME fuels (bio-diesel fuels) at low Engine oils are specially tested for their
claims for damage if: temperatures suitability for use in our engines. For this
reason, only use engine oil brands ap-
the cause of the damage is in any way FAME fuels are reliable down to outside
proved by Mercedes-Benz. These are listed
connected to the use of a FAME fuel temperatures of approximately –20 °C in
in the Mercedes-Benz Specifications for
that does not comply with the accordance with EN 14214.
Service Products. Observe the information
EN 14214 standard
in the Maintenance Booklet.
Flow improvers
the regulations of sheet number 135 of
the Mercedes-Benz Specifications for The addition of flow improvers or kerosene i
Service Products concerning operation has no effect on the cold stability of FAME The use of non-approved engine oil 4
with FAME fuels have not been ob- fuels. brands may limit your warranty entitle-
served ment.
Engine oils
malfunctions or consequential damage
(e.g. paint damage) arise from the han-
dling of or operation with FAME fuels
63
Operation
Service products
64
Operation
Service products
65
66
Maintenance
Maintenance instructions
Work schedule overview
Work schedules
67
Maintenance
Maintenance instructions
This section describes all maintenance The scope of maintenance and frequency
work to be carried out on the engine. Risk of accident G of maintenance work depend on the differ-
ent operating conditions and are listed in
Risk of injury G Faulty maintenance work or failure to carry
out maintenance work, e.g. not changing
the Maintenance Booklet.
Have work that is carried out confirmed
the oil filter or not observing maintenance
Before having maintenance or repair work with an entry in the Maintenance Booklet.
intervals, can cause engine damage. Engine
carried out, please make sure that you read This proof of regular maintenance is al-
damage can lead to an increased risk of an
the relevant sections of the technical docu- ways required for any warranty claims.
accident.
mentation relating to maintenance and re-
Please also observe the maintenance in-
pair measures, e.g.: Therefore, observe the notes on engine
structions for special accessories.
maintenance in these Operating Instruc-
the Operating Instructions and work-
shop information. tions. !
5
Familiarise yourself with the relevant legal Change the engine oil filled at the fac-
regulations before starting work, e.g.: i tory, which complies with Sheet 228.5
All maintenance intervals and mainte- of the Mercedes-Benz Specifications
health as well as safety as well as acci-
dent prevention regulations. nance work refer to genuine for Service Products, if more than
Mercedes-Benz parts and accessories 24 months have elapsed before the en-
You could otherwise fail to recognise dan- gine is operated for the first time.
that have been expressly approved for
gers and could injure yourself or others.
the engine by DaimlerChrysler.
68
Maintenance
Work schedule overview
Work schedule overview
Maintenance service Intake pipe between the air cleaner and Additional work with every
engine third maintenance service
Engine: Cooling and heating system
Oil change and filter replacement Fuel filter:
Replace filter
i Checking and correcting fluid level
Fuel prefilter with water separator:
For operation with diesel fuel: If more fluid is lost than can be accounted
Replace filter element
for by normal consumption, trace the
Change the engine oil and replace
cause and rectify it i
the oil filter at least every two
years. Engine cooling system: If operated with FAME fuel:
Check and correct fluid level and
If operated with FAME fuel (bio-diesel Replace the fuel filter together with
antifreeze/corrosion inhibitor concen-
fuel): engine oil change and filter replace-
tration 5
Change the engine oil and replace ment.
the oil filter at least once every Additional work
Engine brake*:
year. Valve clearance:
Check condition and setting
Check and adjust
Poly-V-belt: Coolant:
Check condition i Renew
The valve clearance must be adjusted
Checking for leaks and general during the first maintenance service i
condition and then during the 3rd, 5th, 7th main- Renewal interval depends on the cool-
tenance services and so on. ant additive used (see Mercedes-Benz
Check for points of abrasion and incorrect
Specifications for Service Products).
positioning.
Engine:
Lines and hoses on the engine
69
Maintenance
Work schedules
Engine: checking for leaks and Lines and hoses on the engine:
general condition checking for leaks and general Risk of injury G
Visual inspection of the engine for condition
There is a danger of limbs being caught, en-
signs of leakage. Visual and aural check for leaks from trapped, crushed or torn off by rotating en-
lines and hoses. Also check that all gine parts. Therefore you should:
Sealing points which are slightly damp can
lines and hoses are undamaged, routed
be ignored. Keep a safe distance between yourself
in such a way that there will be no chaf-
and rotating engine parts, including
! ing and secured correctly.
when the engine is being started.
More significant leaks involving con-
Wait until all engine parts have stopped
stant oil loss must be rectified immedi- Risk of injury G moving before carrying out any work on
ately. the engine.
5 The engine becomes very hot while it is run-
Wear work clothing which is fastened
ning and remains so for some time after it
and close-fitting. Wear a hair net if nec-
has stopped. It will cause burns upon con- essary. Remove jewellery such as
tact. watches and necklaces.
Before starting any work on the engine,
allow all engine parts to cool down or
wear suitable gloves and items of cloth-
ing to protect yourself against hot en-
gine components.
70
Maintenance
Work schedules
Risk of injury G
Hot engine oil escaping under pressure can
scald your skin and eyes. 5
Wear suitable protective gloves, protective
clothing and safety goggles.
Oil filter cap with oil filter element
Oil filter cap 1 Cap
!
Unscrew oil filter cap 1 using the 2 Sealing ring
Make sure that no foreign objects enter 3 Oil filter element
the filter housing. Never wipe the filter socket spanner insert (WAF 36). Allow
housing out because lint or dirt can en- the oil to drain from the filter housing. Unscrew oil filter cap 1 with oil filter
ter the oil circuit. element 3 and unclip oil filter element
3 from the cap by pressing on the
sides of the bottom edge.
71
Maintenance
Work schedules
Replace sealing ring 2 on cap 1 with To do this, pull out the dipstick and in- To drain:
a new one. The sealing ring must be sert an extractor unit sealed with an
Place a suitable collecting receptacle
lightly greased. O-ring into the dipstick guide pipe (ar-
under the oil drain plug (arrow) on the
row).
Insert new oil filter element 3 into underside of the oil sump.
cap 1 and press until it clips into ! Unscrew the oil drain plug carefully and
place.
Observe the operating instructions for allow the oil to drain out.
Screw on cap 1 with the oil filter ele- the engine oil extractor unit.
ment and tighten.
Tightening torque: 40 Nm.
To siphon:
Siphon off the engine oil through the
dipstick guide pipe. Oil drain plug
72
Maintenance
Work schedules
Screw the oil drain plug back in with a Adding engine oil !
new sealing ring and tighten Add new engine oil to the engine via the Keep the engine running at idling speed
Tightening torque: oil filler opening up to the maximum until an oil pressure reading is dis-
M20 x 1.5 – 60 Nm mark on the dipstick. played. If no oil pressure is displayed
M26 x 1.5 – 85 Nm
after approximately 10 seconds,
switch off the engine. Determine the
cause.
73
Maintenance
Work schedules
= intake valve
= exhaust valve
X = flywheel end
74
Maintenance
Work schedules
Installation:
왘 Clean the sealing surfaces of the cylin-
der head and cylinder head cover 1.
5
왘 Always replace seal 4 between cylin-
der head cover 1 and the cylinder
head. Flywheel inspection hole
왘 Attach cylinder head cover 1. 왘 Unscrew the cap from the inspection
Cylinder head cover hole in the flywheel housing.
왘 Insert hexagon socket screw 2 with
1 Cylinder head cover new sealing washers 3 and tighten: 왘 Fit turning tool 904 589 04 63 00 to
2 Hexagon socket screw Tightening torque: 30 Nm. the flywheel housing inspection hole.
3 Sealing washer
4 Seal
5 Engine ventilation hose
75
Maintenance
Work schedules
I – intake valve
5 E – exhaust valve
Adjust all valve clearances in 2 crankshaft
positions.
76
Maintenance
Work schedules
77
Maintenance
Work schedules
Fuel prefilter: cleaning the filter Unscrew oil filter cap 1 and filter ele-
element ment 2 out of the filter housing.
Clean oil filter cap 1 and filter ele-
Risk of fire G ment 2.
5 Environmental note H Insert the filter element into the oil fil-
ter cap and screw the oil filter cap onto
Dispose of used filter elements, seals and the filter housing.
fuel residue in accordance with relevant lo- Fuel prefilter Tightening torque: 25 Nm.
cal regulations.
1 Cap
2 Filter element
3 Sealing ring
Open the tank cap to reduce excess
pressure in the fuel tank.
Clean the outside of the fuel prefilter
and cover any hoses/lines underneath
the prefilter.
78
Maintenance
Work schedules
79
Maintenance
Work schedules
Environmental note H
5
Dispose of used filter elements, seals and
fuel residue in accordance with relevant lo-
cal regulations.
80
Maintenance
Work schedules
Pull cap 1 with the filter element out Remove the cap and filter element. Un-
of filter housing 3 slightly. Allow the clip the filter element by pressing the
fuel to flow out. sides of the lower edge of the filter ele-
ment.
Pull dirt collecting container 4 by the
retainers out of the filter housing.
!
Dirt and water must not be allowed to
enter the filter housing; Do not empty
dirt collecting container 4 in the filter
housing.
5
Clean oil filter cap 1 and dirt collect-
ing container 4.
Replacing the fuel filter element
Replace sealing ring 2 (lightly grease
1 Cap new sealing ring 2 and the seals of
2 Sealing ring the filter element).
3 Filter element 1 Cap
2 Sealing ring Clip new filter element 3 into oil filter
Open the tank cap to prevent excess cap 1.
3 Filter element
pressure in the fuel tank.
4 Dirt collecting container Insert dirt collecting container 4 into
Unscrew fuel filter cap 1 using the 5 Filter housing filter housing 5; make sure it is in-
socket spanner insert (WAF 36). stalled correctly.
81
Maintenance
Work schedules
Screw on the oil filter cap with filter Check the fuel filter for leaks with the
element and tighten engine running.
Tightening torque: 25 Nm.
i
Start the engine and bleed the fuel
To bleed the system manually, the ma-
system.
chine or vehicle must be equipped with
i a hand pump, e.g. on a fuel prefilter.
To bleed the fuel system, there must be
sufficient battery capacity available
during the starting procedure, as the Environmental note H
fuel system must first be replenished
If the diesel fuel level (fuel tank) is above en-
with fuel.
5 gine height, the feed line must be closed
when the filter is replaced. Diesel fuel could
i otherwise flow out.
Run the engine for approximately
1 minute. The fuel system bleeds auto-
matically.
If the engine stalls or does not start,
bleed the fuel system manually.
82
Maintenance
Work schedules
Intake pipe between air cleaner Poly-V-belt: checking condition Check the poly-V-belt for damage sec-
and engine: checking for leaks and tion by section; to do this, turn the en-
gine or poly-V-belt gradually using the
general condition Risk of injury G turning tool until the chalk mark is
Check the rubber sleeves, intake pipes reached again.
and connection hoses for damage and Faulty poly-V-belts may tear and parts or all
leaks. of the belt may be thrown off, thereby caus- !
ing injury to others.
Check the hose clamps, flanged joints Replace the poly-V-belt if one of the
and intake manifold for firm seating. Always observe the specified mainte- damage patterns shown on the next
nance intervals for poly-V-belts. page is detected. For information on fit-
If damage is detected, replace the poly- ting and removing the poly-V-belt
V-belt concerned immediately. ( see page 85).
5
Special tools Remove the turning tool.
Turning tool: 904 589 04 63 00 Screw the cap back into the inspection
hole in the flywheel housing.
Fit the turning tool to the flywheel Tightening torque: 25 Nm.
housing inspection hole.
Make a chalk mark on the poly-V-belt.
83
Maintenance
Work schedules
Damage patterns
84
Maintenance
Work schedules
1 Condition as new (as reference: trape- Removing and fitting the poly-V-belt
zoidal ribs) Risk of injury G
2 One-sided wear: wedge-shaped ribs
3 Cord visible at the base of the ribs The tensioning device is spring-tensioned.
4 Ribs split When it is loosened or tightened, there is a
5 Transverse cracks in several ribs risk of injury from crushing or entrapment in
6 Rubber nodules at the base of the belt pretensioned parts.
7 Deposits of dirt or stones
For this reason, always carry out work
8 Rib detached from the base of the belt
on the tensioning device with extreme
9 Cord torn out at the side
care.
a Outer cord frayed
b Transverse cracks on the back of the Make sure that the tool is handled cor-
rectly.
belt 5
c Transverse cracks in several ribs
Fit the spanner with extension element
and socket spanner insert 15 mm into
the tensioning device.
Clamping handle with extension in the ten-
sioning device Swing the tensioning pulley upwards
and remove the poly-V-belt.
Swing back the tensioning device.
85
Maintenance
Work schedules
Check that both the tensioning device Poly-V-belt routing (engine without Poly-V-belt routing (engine with
and the belt pulley are in perfect condi- refrigerant compressor) refrigerant compressor)
tion (e.g. check for worn bearings on
the tensioning device, tensioning pul-
ley and guide pulleys as well as for
wear on belt pulleys); replace parts if
necessary.
Lay the poly-V-belt (new) on all belt pul-
leys, except for the tensioning pulley
(see illustrations for poly-V-belt rout-
ing).
86
Maintenance
Work schedules
87
Maintenance
Work schedules
88
Maintenance
Work schedules
89
Maintenance
Work schedules
90
Maintenance
Work schedules
i
The cooling system opening pressure
can be determined from the code on
the cap or pressure relief valve. 5
Example: code 70 = 0.7 bar overpres-
sure.
Pressure tester special tool
The cooling system pressure tester has
i a built-in pressure relief valve so that a
Special tool: pressure of 1.2 bar cannot be exceed-
ed.
Pressure tester 001 589 83 21 00
91
Maintenance
Work schedules
92
Maintenance
Work schedules
Connect the drain hose to the coolant Clear blocked drainage openings of i
drainage connection on the radiator deposits.
Observe any further information in the
and drain the coolant.
operating instructions from the
Adding coolant
Connect the drain hose to coolant machine/vehicle manufacturer.
pressure release screw 1 on the Start the engine and run it at varying
engine block and drain the coolant. speeds for approximately 1 minute.
Environmental note H
Dispose of used coolant in accordance with
current local regulations ( see page 65).
93
94
Practical advice
Malfunctions, causes and solutions
Jump-starting
95
Practical advice
Malfunctions, causes and solutions
Have faults that you cannot remedy your- Always have work on or modifications to the
self rectified at a qualified specialist work- engine carried out at a qualified specialist
shop. workshop which has the necessary special-
ist knowledge and tools for the work re-
6 DaimlerChrysler recommends that you use quired.
a Mercedes-Benz Service Centre for this
purpose as it has the necessary specialist Mercedes-Benz recommends that you use a
knowledge and tools for the work required. Mercedes-Benz Service Centre for this pur-
In particular, work relevant to safety or on pose.
safety-related systems must be carried out
at a qualified specialist workshop.
96
Practical advice
Malfunctions, causes and solutions
General troubleshooting
97
Practical advice
Malfunctions, causes and solutions
98
Practical advice
Malfunctions, causes and solutions
99
Practical advice
Malfunctions, causes and solutions
100
Practical advice
Malfunctions, causes and solutions
101
Practical advice
Malfunctions, causes and solutions
102
Practical advice
Malfunctions, causes and solutions
103
Practical advice
Jump-starting
104
Technical data
Engine data
Test values and adjustment values
Tightening torques
105
Technical data
Engine data
Dimensions in mm:
(standard version, other versions on
request)
OM 904 LA
A = Engine length 830 mm
B = Engine width .645 mm
C = Engine height 925 mm
OM 906 LA
OM 926 LA
A = Engine length 1,078 mm
B = Engine width 645 mm OM 904 illustrated OM 904 illustrated
C = Engine height 940 mm
106
Technical data
Engine data
Weights
General data
107
Technical data
Engine data
Displacement
OM 904 LA: 4,250 cm3 /4,800 cm3
OM 906 LA/OM 926 LA: 6,370 cm3 /7,200 cm3
Direction of rotation of engine when looking at flywheel side of engine Anti-clockwise
Starter Electric
Coolant capacity of engine without intercooler
OM 904 LA: 8.5 l
OM 906 LA/OM 926 LA: 12.5 l
Engine oil capacity including oil filter
OM 904 LA: minimum 13 litres; maximum 16 litres
OM 906 LA/OM 926 LA: minimum 24 litres; maximum 29 litres
108
Technical data
Engine data
Starter motor
Voltage 24 V
Output 4.0 kW
Battery (not in scope of delivery)
Voltage 12/24 V
Cold test current in accordance with DIN 72311 maximum 450 A
Cold start ability without jump-starting and 75% battery charge down to maximum –20 °C
Alternator
Voltage 28 V
Current rating 80 A
109
Technical data
Test values and adjustment values
Valve clearance
110
Technical data
Tightening torques
Tightening torques
i
All threads on mechanical parts and re-
lated contact surfaces must be clean,
smooth and lubricated with engine oil;
other lubricants require significantly
different tightening torques.
Designation Nm
Engine block
Bolt securing cylinder head cover to the cylinder head 30
Bolt securing the oil sump to the cylinder crankcase 25
Poly-V-belt tensioning device to the cylinder crankcase/to the hydraulic pump bracket/ 50
to the support
Fuel/injection system
Injection line to the unit pump pressure pipe connection 35
7
Banjo bolts for fuel lines 40
Cap to the fuel filter housing 25
Starter motor/alternator
Starter motor to the timing case 50
Alternator support to the cylinder crankcase 100
111
Technical data
Tightening torques
Designation Nm
Alternator to the support 50
Alternator to the mounting 65
Oil circuit
Oil drain plug to the oil sump
M20 x 1.5 thread 65
M26 x 1.5 thread 85
Alternator mounting to the oil filter 40
Oil filter housing to the crankcase 25
Oil filter housing support to the crankcase 25
Oil filter cap to the oil filter housing 25
Oil pressure sensor to the oil filter housing 25
Valve adjustment
Counternut to the rocker arm adjustment screw 25
7
Cooling circuit
Coolant line with thermostat valve to the coolant pump 25
Coolant pump to the cylinder crankcase 25
Belt pulley to the coolant pump hub 25
112
Index
A D F
Adaptation module . . . . . . . . . . . . . . 29 Diesel . . . . . . . . . . . . . . . . . . . . . . . . . 59 FAME
ADM . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Diesel fuels Fuels . . . . . . . . . . . . . . . . . . . . . . . . 61
Alternator . . . . . . . . . . . . . . . . . . . . 109 In extremely cold weather . . . . . . . . 59 Flow improvers . . . . . . . . . . . . . . 59, 60
Antifreeze/corrosion inhibitor . . . . 65 Sulphur content . . . . . . . . . . . . . . . . 59 FR (drive control) unit . . . . . . . . . . . . 29
Dimensions . . . . . . . . . . . . . . . . . . . 106 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
B Disposal of service products . . . . . . 65 Filter element . . . . . . . . . . . . . . . . . . 81
Battery . . . . . . . . . . . . . . . . 41, 104, 109 Prefilter . . . . . . . . . . . . . . . . . . . . . . 78
Bio-diesel . . . . . . . . . . . . . . . . . . . . . . 61 E Refuelling . . . . . . . . . . . . . . . . . . . . . 41
Emergency running program . . . . . . 25 Fuel additives . . . . . . . . . . . . . . . . . . 59
C Engine Fuel system
Charge current . . . . . . . . . . . . . . . . . 48 Checking for leaks and general Bleeding . . . . . . . . . . . . . . . . . . . . . . 41
Conversion parts and condition . . . . . . . . . . . . . . . . . . . . . 70 Fuels
modifications . . . . . . . . . . . . . . . . . . 36 Cleaning . . . . . . . . . . . . . . . . . . . . . . 54 Diesel . . . . . . . . . . . . . . . . . . . . . . . . 59
Coolant . . . . . . . . . . . . . . . . . . . . . . . . 64 Oil change and filter FAME . . . . . . . . . . . . . . . . . . . . . . . . 61
Mixing ratio . . . . . . . . . . . . . . . . . . . 65 replacement . . . . . . . . . . . . . . . . . . . 71
Renewing . . . . . . . . . . . . . . . . . . . . . 92 Starting . . . . . . . . . . . . . . . . . . . . . . 45 G
Coolant level . . . . . . . . . . . . . . . . . . . 89 Stopping . . . . . . . . . . . . . . . . . . . . . . 51 Genuine Mercedes-Benz parts . . . . . 38
Cooling system Engine brake . . . . . . . . . . . . . . . . . . . 24 Grid heater . . . . . . . . . . . . . . . . . . 26, 50
Cleaning . . . . . . . . . . . . . . . . . . . . . . 55 Checking condition . . . . . . . . . . . . . 87
Degreasing . . . . . . . . . . . . . . . . . . . . 57 Checking condition and H
Cylinder head cover setting . . . . . . . . . . . . . . . . . . . . . . . 87 High-pressure cleaners . . . . . . . . . . 55
Removing and fitting . . . . . . . . . . . . 75 Engine data . . . . . . . . . . . . . . . . . . . 106
I
Engine data card . . . . . . . . . . . . . . . . 22
Installation . . . . . . . . . . . . . . . . . . . . . 32
8
Engine oil
Intake pipe
SAE classifications . . . . . . . . . . . . . . 63
Checking for leaks . . . . . . . . . . . . . . 83
Engine plate . . . . . . . . . . . . . . . . . . . . 20
Environmental note . . . . . . . . . . . . . . 5
113
Index
J P T
Jump-starting . . . . . . . . . . . . . . . 34, 104 Personnel . . . . . . . . . . . . . . . . . . . . . . 30 Telligent® engine system . . . . . . 29, 49
Poly-V-belt Test values and adjustment
K Checking condition . . . . . . . . . . . . . 83 values . . . . . . . . . . . . . . . . . . . . . . . . 110
Kerosene . . . . . . . . . . . . . . . . . . . 59, 60 Removing and fitting . . . . . . . . . . . . 85 Tightening torques . . . . . . . . . . . . . 111
Routing . . . . . . . . . . . . . . . . . . . . . . . 86 Transport . . . . . . . . . . . . . . . . . . . . . . 31
L
Protection of the Transport and installation . . . . . . . . 31
Location of sensors . . . . . . . . . . . . . 18
environment . . . . . . . . . . . . . . 5, 30, 36 Troubleshooting . . . . . . . . . . . . . . . . 96
M Protective treatment . . . . . . . . . . . . 57 Cause . . . . . . . . . . . . . . . . . . . . . . . . 97
Maintenance instructions . . . . . . . . 68 General . . . . . . . . . . . . . . . . . . . . . . . 97
R Solution . . . . . . . . . . . . . . . . . . . . . . 97
Maintenance intervals . . . . . . . . . . . 40
Renewal interval Type designation . . . . . . . . . . . . . . . . 22
Maintenance service . . . . . . . . . . . . . 69
Engine oil . . . . . . . . . . . . . . . . . . . . . 69
MR (engine control) unit . . . . . . . . . . 27
Oil filter . . . . . . . . . . . . . . . . . . . . . . 69 V
O Replacing the fuel filter Valve clearance
Oil drain plug . . . . . . . . . . . . . . . . . . . 72 element . . . . . . . . . . . . . . . . . . . . . . . 80 Adjusting . . . . . . . . . . . . . . . . . . . . . 74
Oil filter replacement . . . . . . . . . . . . 71 Checking . . . . . . . . . . . . . . . . . . . . . 76
S
Oil pressure . . . . . . . . . . . . . . . . . . . . 48
Safety and emergency running W
Operating safety . . . . . . . . . . . . . . . . . 6
program . . . . . . . . . . . . . . . . . . . . . . . 25 Warranty entitlement . . . . . . . . . . . . 58
Overview
Safety precautions . . . . . . . . . . . . . . 34 Water . . . . . . . . . . . . . . . . . . . . . . . . . 64
OM 460 LA . . . . . . . . . . . . . . . . . . . . 10
Service products . . . . . . . . . . . . . 58, 65 Weights . . . . . . . . . . . . . . . . . . . . . . 107
8 Special lubricant additives . . . . . . . . 58 Winter operation . . . . . . . . . . . . . . . . 52
Starter motor . . . . . . . . . . . . . . . . . . 109 Work schedules . . . . . . . . . . . . . . . . . 78
Starting the engine for
the first time . . . . . . . . . . . . . . . . 40, 42
Starting using a donor
battery . . . . . . . . . . . . . . . . . . . . . . . 104
114