Professional Documents
Culture Documents
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
Single Button Remote Control 3-Button Remote Control Premium Remote Control Mini-Remote Control
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or
For use with garage door openers, gate operators or other products that are 315 MHz Security✚®. play with remote controls.
Compatible with garage door openers that have a purple learn button. The code between the remote • Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no
control and the receiver changes with each use, randomly accessing over a billion new codes. Refer obstructions to door travel.
to your product manual for the location of the learn button. • ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
NOTE: Your product may look different than the products illustrated in this manual. cross path of moving gate or door.
PROGRAMMING THE REMOTE CONTROL
1 2 3 Press and hold the button Release the button
”
on the remote control “click ” when the garage
“click
Locate the that you wish to use. door opener lights
Smart/Learn blink or two clicks
button. Press and are heard.
immediately release If programming to
the learn button. other products,
The learn LED will glow press the button a
steadily for 30 seconds. second time to
Within 30 seconds... activate the product.
1 2 3 ”
With the door closed, “click ” After the garage
press and hold Press and Press and “click
door opener
the remote hold the hold the lights flash,
control button
that you want to
control the light.
+ light button
on the LOCK
LIGHT
+ lock button
on the LOCK
LIGHT
release all
buttons.
door control. door control.
Test by pressing the remote control button. The garage door opener lights should turn on or off but the door should not move.
TO ERASE ALL CODES FROM MEMORY
When deactivating any unwanted remote control code, all previous codes will be erased.
1
Press and hold the learn button
on garage door opener or other
product until the learn LED goes
out (approximately 6 seconds).
All previous codes are now erased.
Reprogram each remote control
you wish to use.
THE REMOTE CONTROL BATTERY
The lithium battery should 1 Use the visor clip or 2 Remove the old battery. 3 Insert replacement 4 Replace cover.
produce power for up to 5 years. screwdriver to pry open Dispose of old batteries batteries positive side up.
To replace battery: the cover. properly. Replace the batteries
with only 3V2032 To prevent possible SERIOUS INJURY or DEATH:
coin cell • NEVER allow small children near batteries.
batteries. • If battery is swallowed, immediately notify doctor.
3V2032
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Replace ONLY with 3V2016 or 3V2450 coin batteries.
Premium Remote Control Only 1 Remove the two screws 2 Slide the old batteries out. 3 Insert replacement 4 Replace screws. • DO NOT recharge, disassemble, heat above 212°F
(100°C) or incinerate.
The 3V2016 lithium batteries for and open the remote Dispose of old batteries batteries positive side up.
the opener and LEDs (marked control housing. properly. Replace the batteries with
only 3V2016 or 3V2450 NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment
“LED and Opener Battery”) should or modifications of this receiver and/or transmitter are prohibited, except for
last up to 5 years. The 3V2450 coin cell 3V2450 changing the code setting or replacing the battery. THERE ARE
lithium battery for the proximity batteries. NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation
lighting (marked “Proximity is subject to the following two conditions: (1) this device may not cause
Battery”) should last 1-2 years. 3V2016 harmful interference, and (2) this device must accept any interference
To replace the batteries: received, including interference that may cause undesired operation.