Professional Documents
Culture Documents
RELIABILITY
SINCE 1927
Table of Contents
Bukup Tongs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Striking Wrench — 6-pt. Straight. . . . . . . . . . . . . . . . 5
Striking Face Box Wrench — 12-pt. Offset . . . . . . . . 5 Warranty . . . . . . . . . . . . . . . . . . . . . . inside back cover
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Pipe Size Gripping Width Tong Length Weight
C11-P 1/8" – 1-1/2" 1.76" 20" 6 lbs.
C12-P 1/4" – 2-1/2" 2.25" 27" 10 lbs.
C13-P 3/4" – 4" 2.67" 37" 20 lbs.
C135-P 1" – 6" 2.89" 45" 27 lbs.
C14-P 1-1/2" – 8" 3.09" 51" 31 lbs.
C15-P 2" – 12" 3.35" 65" 56 lbs.
C16-P 4" – 18" 4.63" 87" 147 lbs.
WARNING! Use as a hand tool only. Do Not Strike, use a “cheater” or extend handle. SERIOUS INJURY may result if used improperly.
Read Safe Practices & Procedures Manual prior to operation. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
Specifications
Part No. Pipe Size Gripping Width Tong Length Weight
C27-P 1/4" – 2-1/2" 2.19" 27" 11 lbs.
C37-P 3/4" – 4" 2.69" 37" 19 lbs.
C47-P 1" – 6" 3.00" 47" 30 lbs.
C57-P 1-1/2" – 8" 3.38" 57" 42 lbs.
C67-P 2" – 12" 3.69" 67" 59 lbs.
WARNING! Use as a hand tool only. Do Not Strike, use a “cheater” or extend handle. SERIOUS INJURY may result if used improperly.
Read Safe Practices & Procedures Manual prior to operation. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
2 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Fitting Tongs
» Work narrow or confined gripping areas
» Easily applied and removed from workpiece
» Equipped with heat-treated chain
Specifications
Part No. Pipe Size Gripping Width Tong Length Weight
C27-F 1/4" – 2-1/2" .69" 23-1/4" 8 lbs.
C57-F 1-1/2" – 8" 1.13" 54-1/2" 32 lbs.
WARNING! Use as a hand tool only. Do Not Strike, use a “cheater” or extend handle. SERIOUS INJURY may result if used improperly.
Read Safe Practices & Procedures Manual prior to operation. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
Chain Tongs
» Vee-shaped jaw
» Grips in downward motion, ratchets in upward motion
» Equipped with heat-treated chain
» Sizes capable of delivering up to 3,000 ft.-lbs. torque
Specifications
Part No. O.D. Gripping Width Handle Length* Weight
STEEL
CPA13 1-1/2" – 6" 2.62" 30" 18 lbs.
CPA14 2" – 10" 3.13" 44" 35 lbs.
ALUMINUM (for light-duty applications only)
CPA14-L60AL 2" – 10" 3.13" 60" 25 lbs.
*Call factory for torque arm lengths.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
254.675.8651 3
LEGENDARY
RELIABILITY
SINCE 1927
4 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Striking Wrench
Specifications
6-pt. Straight Part No. Stud Size Nut Size Head Diameter Weight
SW01 5/8" 1-1/16" 1-11/16" 1-7/8 lbs.
SW02 3/4" 1-1/4" 1-15/16" 2 lbs.
SW03 7/8" 1-7/16" 2-1/4" 3-1/4 lbs.
SW04 1" 1-5/8" 2-1/2" 4-5/8 lbs.
SW05 1-1/8" 1-13/16" 2-11/16" 4-3/4 lbs.
SW06 1-1/4" 2" 2-15/16" 5-5/8 lbs.
» I-beam design for greater handle strength SW07 1-3/8" 2-3/16" 3-3/16" 6-7/8 lbs.
254.675.8651 5
LEGENDARY
RELIABILITY
SINCE 1927
HAMMERTIGHT™
» Designed to hold a striking wrench on a nut
Wrench Retainer » Safer, hands free, one man operation
Patent #9,079,300 » Suitable for 6-pt. and 12-pt. straight or offset wrenches
» Surface coated for rust protection
Specifications
Imperial Sizes
Part No. Fits Stud Size Nut Size Overall Length Weight
HTS58 5/8" - 11 1-1/16" 1-11/16" 8 ozs.
HTS34 3/4" - 10 1-1/4" 1-3/4" 10 ozs.
HTS78 7/8" - 9 1-7/16" 2" 13 ozs.
HTS100 1" - 8 1-5/8" 2-1/4" 1 lb.
HTS118 1-1/8" - 8 1-13/16" 2-5/16" 1-1/8 lbs.
HTS114 1-1/4" - 8 2" 2-1/2" 1-3/8 lbs.
HTS138 1-3/8" - 8 2-3/16" 2-11/16" 1-1/2 lbs.
HTS112 1-1/2" - 8 2-3/8" 2-7/8" 1-5/8 lbs.
HTS158 1-5/8" - 8 2-9/16" 3-1/16" 1-7/8 lbs.
HTS134 1-3/4" - 8 2-3/4" 3-1/16" 2-1/8 lbs.
HTS178 1-7/8" - 8 2-15/16" 3-1/8" 2-3/8 lbs.
HTS200 2" - 8 3-1/8" 3-3/16" 2-1/2 lbs.
HTS214 2-1/4" - 8 3-1/2" 3-1/4" 2-7/8 lbs.
HTS212 2-1/2" - 8 3-7/8" 3-11/16" 3-5/8 lbs.
Imperial Sets
Place wrench on nut and thread Part No. Description Weight
retainer onto stud
HTS34178 Set of 10, 1 each of HTS34 thru HTS178 22 lbs.
Metric Sizes
Part No. Fits Stud Size Nut Size Overall Length Weight
HTSM16 16mm - 2.0 24mm 1-11/16" 8 ozs.
HTSM18 18mm - 2.5 27mm 1-11/16" 9 ozs.
HTSM20 20mm - 2.5 30mm 1-3/4" 10 ozs.
HTSM22 22mm - 2.5 32mm 1-3/4" 11 ozs.
HTSM24 24mm - 3.0 36mm 2" 13 ozs.
Lift up on wrench to compress HTSM27 27mm - 3.0 41mm 2-1/4" 1 lb.
spring loaded retaining plate HTSM30 30mm - 3.5 46mm 2-5/16" 1-1/8 lbs.
HTSM33 33mm - 3.5 50mm 2-1/2" 1-3/8 lbs.
HTSM36 36mm - 4.0 55mm 2-11/16" 1-1/2 lbs.
HTSM39 39mm - 4.0 60mm 2-7/8" 1-5/8 lbs.
HTSM42 42mm - 4.5 65mm 3-1/16" 1-7/8 lbs.
HTSM46 46mm - 5.0 72mm 3-1/16" 2-1/8 lbs.
HTSM48 48mm - 5.0 75mm 3-1/8" 2-3/8 lbs.
HTSM52 52mm - 5.0 80mm 3-1/4" 2-1/2 lbs.
HTSM56 56mm - 5.5 85mm 3-1/4" 2-5/8 lbs.
Reposition wrench on nut and HTSM60 60mm - 5.5 90mm 3-11/16" 2-7/8 lbs.
release spring loaded plate to
HTSM64 64mm - 6.0 95mm 3-11/16" 3-5/8 lbs.
continue
Metric Sets
Part No. Description Weight
HTSM1639 Set of 10, 1 each of HTSM16 thru HTSM39 20-1/2 lbs.
HTSM1842 Set of 10, 1 each of HTSM18 thru HTSM42 22 lbs.
HTSM2046 Set of 10, 1 each of HTSM20 thru HTSM46 23-1/2 lbs.
6 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Description Weight
RTB1 Spring Loaded Hinged Lid 1-1/2 lbs.
RTB2 Clipboard Mounted Lid 1-1/2 lbs.
Sight Glass
» Provides a clear view of flow through drain lines at all times
» Shatter-resistant polycarbonate
» Withstands prolonged esposure to Ultraviolet rays and can
be used in temperatures from -150° to 165°F
Specifications
Part No. O.D. x L Wall Thickness Connection Weight
SG0500 2" x 8" 0.406" Threaded 15 ozs.
SG0500V 2" x 8" 0.406" Victaulic Groove 15 ozs.
SG1000* 2" x 8" 0.500" Threaded 1 lb.
SG1000V* 2" x 8" 0.500" Victaulic Groove 1-1/16 lbs.
SG0500-3 3" x 8" 0.312" Threaded 1-1/16 lbs.
SG0500V-3 3" x 8" 0.312" Victaulic Groove 1-3/16 lbs.
SG0500-4 4" x 8" 0.500" Threaded 2-3/16 lbs.
SG0500V-4 4" x 8" 0.500" Victaulic Groove 2-1/4 lbs.
*Special lengths available upon request.
WARNING! Always place the pipe wrench on the metal connections and not the sight glass itself when tightening. Do not
tighten or loosen while under pressure. Avoid direct contact with strong acids or chemicals such as carbon disulfide
acetone, etc. The PETOL™ Sight Glass is to be used on drain lines ONLY. NEVER use on flow lines.
Always use an oily rag when cleaning the sight glass.
254.675.8651 7
LEGENDARY
RELIABILITY
SINCE 1927
Flange Aligning Tool » Effective solution for tough flange alignment jobs
» Tapered shaft eliminates the need for hammering or prying
» Made of alloy steel and surface coated for rust protection
» Sold individually and in sets
If necessary, use a second tool and
Find a bolt hole aligned enough for the turn until the bolt holes are in
tapered shaft to fit through and turn alignment and insert flange bolts
LENGTH
Specifications Specifications
Part No. Bolt Hole Size Length Weight Extra Long
FT00 3/8" 2-1/8" 3/4 ozs. Part No. Bolt Hole Size Length Weight
FT0 1/2" 2-3/8" 2-3/8 ozs. FT0L 1/2" 5-3/8" 5 ozs.
FT01 5/8" 2-3/4" 4 ozs. FT01L 5/8" 5-3/4" 8 ozs.
FT02 3/4" 3-1/4" 7 ozs. FT02L 3/4" 6-1/4" 14 ozs.
FT03 7/8" 3-1/2" 10 ozs. FT03L 7/8" 6-1/2" 1-1/8 lbs.
FT04 1" 4" 15 ozs. FT04L 1" 7" 1-1/2 lb.
FT06 1-1/8" 5" 1-1/2 lbs. FT06L 1-1/8" 8" 2-1/4 lbs.
FT08 1-1/4" 5-1/2" 2 lbs. FT08L 1-1/4" 8-1/2" 3 lbs.
FT1012 1-3/8" 6-1/4" 2-7/8 lbs. FT1012L 1-3/8" 9-1/4" 4 lbs.
FT14 1-1/2" 6-1/2" 3-1/4 lbs. FT14L 1-1/2" 9-1/2" 4-5/8 lbs.
FT16 1-5/8" 7-1/4" 4-1/8 lbs. FT16L 1-5/8" 10-1/4" 5-3/4 lbs.
FT1820 1-3/4" 7-7/8" 4-3/4 lbs. FT1820L 1-3/4" 10-7/8" 6-5/8 lbs.
FT22 1-7/8" 8-3/8" 5-7/8 lbs. FT22L 1-7/8" 11-3/8" 8-1/8 lbs.
FT2426 2" 9" 6-5/8 lbs. FT2426L 2" 12" 9-1/4 lbs.
FT30 2-1/8" 12" 10-3/4 lbs. FT30L 2-1/8" 15" 13-1/2 lbs.
FT34 2-3/8" 13-1/4" 13-1/2 lbs. FT34L 2-3/8" 16-1/4" 17-1/4 lbs.
FT3642 2-5/8" 14" 17 lbs. FT3642L 2-5/8" 17" 21 lbs.
FT48 2-7/8" 13-5/8" 24-3/8 lbs. Extra Long Sets
Part No. Description Weight
FT5054 3-1/8" 18" 35-3/4 lbs.
FTS24L Set of 6, 2 ea. of FT02L, FT03L, 12-3/4 lbs.
FT60 3-5/8" 20" 55-1/4 lbs.
FT04L
Sets
FTS26L Set of 8, 2 ea. of FT02L, FT03L, 17-1/4 lbs.
Part No. Description Weight
FT04L, FT06L
FTS24 Set of 6, 2 ea. of FT02, FT03, FT04 8-1/8 lbs.
FTS28L Set of 10, 2 ea. of FT02L, FT03L, 20-1/8 lbs.
FTS26 Set of 8, 2 ea. of FT02, FT03, FT04, 11 lbs. FT04L, FT06L, FT08L
FT06
FTS212L Set of 12, 2 ea. of FT02L, FT03L, 31 lbs.
FTS28 Set of 10, 2 ea. of FT02, FT03, FT04, 15 lbs. FT04L, FT06L, FT08L, FT1012L
FT06, FT08
FTS212 Set of 12, 2 ea. of FT02, FT03, FT04, 20-1/2 lbs. NOTE: Special lengths available upon request.
FT06, FT08, FT1012
FTS1426 Set of 8, 2 ea. of FT14, FT16, FT1820, 47 lbs.
FT2426
8 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Flange Lifter » Safe & easy installation and removal of blind and weld neck
flanges without the need for a lifting eye
Patent #8,434,800 and 8,434,801 » Designed to comply with ASME Specifications B30.20 and
BTH-1, Design Category B, Service Class 4
» Serialized and stamped with Load Rating
» Supplied with Data Book containing operating instructions,
warnings, load test certificates and MPI certificate
To determine appropriate tool for job requirement, see the Flange Lifter
Selection Guide available on product page of website.
Flange Lifting Shackle » Designed to securely attach to flanges when installing and
removing blind and weld neck flanges
Patent #10,703,611 » Automatically adjusts to bolt hole spacing
» Complies with ASME Specifications B30.20 and BTH-1,
Design Category B, Service Class 4
» Stamped with Load Rating and serial number
» Supplied Data Book contains operating instructions,
warnings, load test certificates and MPI certificate
No lifting eye
required Specifications
Part No. Fits Bolt Size Fits Flange Thickness Weight Rated Load
FLS3 5/8" min. up to 3" 18-1/2 lbs. 2,000 lbs.
FLS6 7/8" min. up to 6" 32 lbs. 5,000 lbs.
FLS11 1-1/8" min. up to 11" 49-5/8 lbs. 14,000 lbs.
To determine appropriate tool for job requirement, see the Flange Lifting
Shackle Selection Guide available on product page of website.
254.675.8651 9
LEGENDARY
RELIABILITY
SINCE 1927
POP-IT™
» Versatile and easy to use
Flange Spreader & » Replaces using hammers, wedges and prybars when
Prying Tool working with flanges
» Precision adjustment and holds setting without drifting
» Used in a wide range of industries as well as emergency
rescue
Specifications
Part No. Minimum Spread Maximum Spread Capacity Weight
P95-525 1/16" 5-1/4" 10,000 lbs. 11 lbs.
PHD0535 1/2" 5-1/2" 30,000 lbs. 33 lbs.
P95-525
3" 8-1/2" 20,000 lbs. 33 lbs.
PCH1
Always Chock
Your Work!
Flange Spreader
» Separates pipe flanges and ring-type-joint flanges
» Safe and easy to use
» Suitable for use in a wide range of industries
Specifications
Part No. Inside Frame Width Flange Pin Diameter* Weight
N14 2-3/4" 5/8" 8 lbs.
N48 3-3/4" 3/4" 9 lbs.
Most efficient flange separation is N812 4-7/8" 7/8" 10 lbs.
achieved using spreaders in pairs
N1216 6-1/8" 1" 15 lbs.
N1620 7-1/2" 1-1/8" 18 lbs.
N2024 9-1/8" 1-1/4" 20 lbs.
*Special smaller flange pins may be required for some flange sizes. Call
factory for assistance.
10 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Strap Width Fits Flange O.D. Up to Weight
FD1 2" 22" 2 lbs.
FD2 2" 45" 2-3/4 lbs.
WARNING! Improper use of flange spray deflectors may result in INJURY OR DEATH! Read Operating Instructions
prior to operation. This device IS NOT intended to replace any personal protective equipment (PPE). Before using, inspect
the strap for cuts, tears, burns or damage and replace or return any damaged tool. DO NOT use to seal or contain any pressure. DO
NOT use for lifting or support of any load. DO NOT use to hold flanges in alignment. DO NOT use to support an unbolted line, blind,
valve or fitting. DO NOT use on surfaces that exceed 275° F. Always follow OSHA guidelines for Process Safety Management.
254.675.8651 11
LEGENDARY
RELIABILITY
SINCE 1927
Flange Wrench
» Quickly tighten or loosen threaded flanges
» Replaces other methods often used in the field
» Pins fit easily into flange bolt holes
Specifications
Part No. Pin Diameters Works Wall Thickness (A) Length Weight
FW1 1/2" up to 1/2" 18" 5-5/8 lbs.
5/8" up to 3/4"
Refinery Wrench
» Combination pipe wrench/valve wheel wrench
» Handles are cast from alloy steel or aluminum
» Designed for multiple uses in the refining, petrochemical and
gas processing industries
Specifications
Part No. Pipe Capacity Wheel Wrench Opening Length (Closed) Weight
STEEL
RW1 1/8" – 1" 3/4" 10" 1-1/2 lbs.
RW2 1/8" – 1-1/2" 1/2" 10" 1-3/4 lbs.
ALUMINUM (for light-duty applications only)
RW1AL 1/8" – 1" 3/4" 10" 12 ozs.
RW2AL 1/8" – 1-1/2" 1/2" 10" 1 lb.
STEEL (with SURGRIP™ valve wheel wrench opening)
RW1SG 1/8" – 1" 3/4" 10" 1-5/8 lbs.
SURGRIP™ style opening RW2SG 1/8" – 1-1/2" 1/2" 10" 2-1/4 lbs.
further reduces chance
of wrench slipping WARNING! Protect yourself and others from SERIOUS INJURY!
Never use a “cheater” or other means to extend handle!
If wrench slips you can be hurt or injure other workers!
NOTE: Safe Practices & Procedures can be found on page 38 of this product guide.
12 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Description Length* Weight
STEEL
VW0 Forged, Double-end 8" 14 ozs.
VW0CPTC** Forged, Double-end 8" 12 ozs.
VW10 Forged, Double-end 10" 1-3/4 lbs.
VW1 Forged, Single-end 15" 2-3/8 lbs.
VW12 Forged, Double-end 18" 4-1/4 lbs.
VW2 Forged, Single-end 22" 4-3/4 lbs.
VW3 Forged, Single-end 27" 10 lbs.
VW4 Forged, Single-end 48" 16-1/4 lbs.
VW5 Cast, Single-end 48" 16 lbs.
VW6 Cast, Single-end 48" 15-3/4 lbs.
BRONZE
VW0BR Cast, Double-end 8" 15-1/4 ozs.
VW10BR Cast, Double-end 10" 1-7/8 lbs.
VW1BR Cast, Single-end 15" 2-3/8 lbs.
VW12BR Cast, Single-end 15-1/2" 2-7/8 lbs.
VW2BR Cast, Single-end 22" 4-3/4 lbs.
VW3BR Cast, Single-end 30" 9-1/8 lbs.
ALUMINUM
VW0AL Cast, Double-end 8" 5 ozs.
VW10AL Cast, Double-end 10" 10-1/2 ozs.
*Overall Length is approximate
**Cadmium plated, Teflon coated
DIMENSIONS
A B
Size Small Large Small Large
0 5/8" 3/4" 1/2" 21/32"
0CPTC 7/16" 7/16" 1/2" 21/32"
10 7/8" 1-1/8" 11/16" 1"
A 1 1-1/4" 1"
12 1-1/8" 1-13/16" 1" 1-5/16"
12BR 1-3/8" 1-3/8"
2 1-13/16" 1-5/16"
B
3 2-1/2" 2"
4 2-11/16" 2-1/4"
5 2-3/4" 2-1/2"
6 2-7/8" 2-3/4"
254.675.8651 13
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Pattern Overall Length* Weight
VW0SG Double-end 8" 14 ozs.
VW0LSG Double-end 15" 1-3/8 lbs.
VW10SG Double-end 10" 1-1/2 lbs.
VW12SG Double-end 22" 4-5/8 lbs.
VW1SG Single-end 22" 5 lbs.
VW2SG Single-end 27" 5-5/8 lbs.
VW3SG Single-end 27" 12 lbs.
*Overall Length is approximate
DIMENSIONS
A B
Size Small Large Small Large
A VW0SG 1/2" 3/4" 1/2" 21/32"
VW0LSG 1/2" 3/4" 1/2" 21/32"
VW10SG 9/10" 1" 11/16" 1"
VW12SG 1-1/10" 1-1/4" 1" 1-5/16"
B VW1SG 1-1/10" 1"
VW2SG 1-1/4" 1-5/16"
VW3SG 2-1/10" 2"
14 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
254.675.8651 15
LEGENDARY
RELIABILITY
SINCE 1927
Tubing Tongs
» Design allows operator to “snap” the tool onto the
workpiece for positive grip
» Cam lever serves to both lock and open the jaws
» Replaceable hardened steel bits
Specifications
Part No. O.D. Gripping Width Handle Length Weight
Medium Heavy Duty
TMA2002375 2.375" 1.25" 31-1/2" 17 lbs.
TMA2502875 2.875" 1.25" 33-13/16" 19 lbs.
TMA2503063 3.063" 1.25" 33-13/16" 19 lbs.
TMA3003500 3.500" 1.25" 35" 25 lbs.
TMA3003668 3.668" 1.25" 35" 26 lbs.
TMA3504000 4.000" 1.25" 35-1/2" 28 lbs.
TMA3504250 4.250" 1.25" 35-1/2" 29 lbs.
Heavy Duty
THA2002375 2.375" 2.00" 33-3/8" 27 lbs.
THA2502875 2.875" 2.00" 39-5/8" 30 lbs.
THA3003500 3.500" 2.00" 40" 35 lbs.
16 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Suckerod Elevator
254.675.8651 17
LEGENDARY
RELIABILITY
SINCE 1927
» Make up sucker rods when a snap-type Never use a “cheater” or other means to extend handle!
If wrench slips you can be hurt or injure other workers!
wrench is not necessary
» Made of heat-treated alloy steel to
withstand rugged use
18 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Suckerod
Coupling Spinner
» Quickly threads rod couplings onto sucker rods
» Made of neoprene
» One size fits all couplings
Specifications
Part No. Drive Size Overall Dimensions Weight
QS1S 1/2" 2-3/8" O.D. x 2-1/4" 6-1/2 ozs.
Stabbing Tongs
» Quickly spins up couplings or small pipe
» Easily applied and removed
» Lightweight tool provides proper leverage
Specifications
Part No. O.D. Gripping Width Tong Length Weight
SSA1 1-1/4" – 4" 2.13" 13" 9 lbs.
SSA2 2" – 4" 2.25" 16" 10 lbs.
Specifications
Part No. O.D. Gripping Width Handle Length Weight
SHA3 3.000" 2.00" 26" 8 lbs.
254.675.8651 19
LEGENDARY
RELIABILITY
SINCE 1927
HYDRA-TORK™ Units
Basic Unit
Skid-Mounted Unit
Poratble Units
» Safely provides convenience and speed in breaking out
drill stem and drilling tools at the jobsite
» Equipped with PETOL™ Drill Pipe Tongs (see page 22)
» Heat-treated chains are equipped with heavy duty bolts
to quickly adjust from one O.D. to another
» Sizes capable of deliverying up to 95,000 ft.-lbs. torque
Specifications
Part No. O.D. Weight
U1344 1" – 6" 180 lbs.
U4174 3" – 8-1/4" 510 lbs.
U8184 4" – 14" 1,400 lbs.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
20 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Visetongs
Pulldown
Pushup
» Designed for heavy load breakout jobs and large torque
makeup requirements
» Chain easily slides through jaw and locks in place to fit any
size in the O.D. range
» Available in pulldown and pushup designs
» Sizes capable of delivering up to 200,000 ft.-lbs. torque
Specifications — Pushup Specifications — Pulldown
Gripping Handle Gripping Handle
Part No. O.D.* Width Length** Weight*** Part No. O.D.* Width Length** Weight***
VTUA118-4D 4" – 24" 9.00" 54" 328 lbs. VTDA115H 2" – 8" 5.25" 24" 74 lbs.
VTUA118-4D-L36 4" – 24" 9.00" 36" 294 lbs. VTDA116H-4D 4" – 14" 7.25" 36" 170 lbs.
VTUA120 6" – 24" 12.63" 42" 559 lbs. VTDA118-4D 4" – 24" 9.00" 46" 313 lbs.
VTDA120 6" – 24" 12.63" 36" 575 lbs.
*Chain assemblies must be ordered separately. See Chain Selection Guide on product page of website.
**Call factory for torque arm lengths.
***Weights do not include chain.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
Tongvise
Specifications
Part No. O.D.* Gripping Width Weight***
TVA115H 2" – 8" 5.25" 41 lbs.
TVA116 4" – 14" 7.00" 107 lbs.
TVA116H 4" – 14" 7.25" 121 lbs.
TVA118 4" – 24" 9.00" 247 lbs.
TVA120 6" – 24" 12.63" 472 lbs.
*Chain assemblies must be ordered separately. See Chain » Suitable for heavy-duty breakout or makeup operations
Selection Guide on product page of website.
**Weights do not include chain.
» Chain easily slides through jaw and locks in place to fit
any size in the O.D. range
>>> Maximum Working Loads <<< » Self-tightening feature increases grip as torque
Torques vary according to vise being used. increases
See Max. Working Loads on product page of website. » Sizes capable of delivering up to 200,000 ft.-lbs. torque
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
254.675.8651 21
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
DA4174-L08
Part No. O.D.* Gripping Width Handle Length** Weight***
DA1344 1" – 6" 4" 8" 13 lbs.
DA2344-C12 2-1/8" – 5" 4.44" 12" 29 lbs.
DA2344-L21 2-1/8" – 5" 4.44" 21" 35 lbs.
DA4174-L08 3" – 8-1/4" 5.00" 8" 33 lbs.
DA4174-C12 3" – 8-1/4" 5.00" 12" 41 lbs.
DA4174-L21 3" – 8-1/4" 5.00" 21" 45 lbs.
DA4174-L36 3" – 8-1/4" 5.00" 36" 58 lbs.
DA6184-C10 4-1/4" – 10-3/4" 4.88" 10" 49 lbs.
-L21, -L23, -L28, -L36 DA6184-L36 4-1/4" – 10-3/4" 4.88" 36" 76 lbs.
DA8184-C09 4" – 14" 7.25" 9" 91 lbs.
DA8184-C18 4" – 14" 7.25" 18" 100 lbs.
DA8184-L23 4" – 14" 7.25" 23" 120 lbs.
DA8184-L28 4" – 14" 7.25" 28" 129 lbs.
DA8184-L36 4" – 14" 7.25" 36" 134 lbs.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
22 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Specifications
Part No. Overall Dimensions (W x H) Weight
TJA35 with
SlimGrip Tong TJA35 20.85" x 45.70" 260 lbs.
TJA35T 20.85" x 55.81" 295 lbs.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
254.675.8651 23
LEGENDARY
RELIABILITY
SINCE 1927
SlimGrip Tongs
» Designed to work connections with narrow gripping
areas
» Self-adjusting, ratcheting “pipe wrench” with a torque
rating
» Can easily be placed either on top of or underneath the
workpiece
» Sizes capable of delivering up to 7,500 ft.-lbs. torque
Specifications
Part No. O.D. Gripping Width Handle Length Weight
SLG10 1" – 2" 1.19" 16" 9 lbs.
SLG13 2-3/8" – 4" 1.75" 28" 44-1/2 lbs.
SLG15 3-3/4" – 6-1/2" 1.25" 33" 65 lbs.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload.
Do not operate without a manual. Follow OSHA, NSC, etc. standards, safe practices, and procedures.
Rig Wrench
» For fast makeup or breakout of drill pipe on water well
and blast hole rigs
» Self-adjusting, non-jamming ratchet action
» Easily applied or removed from the workpiece
» Capable of delivering up to 16,000 ft.-lbs. torque
Specifications
Torque
Part No. O.D.* Gripping Width Arm Length Weight
PRWA01 3-1/2" – 5" 2.25" approx. 18"** 53 lbs.
PRWA01-D 3-1/2" – 5" 2.25" approx. 22"*** 55 lbs.
*T-4 or T-7 Inserts must be used to work used to work 3-1/2" O.D.
Diamond Point or Teeth Inserts can be used to work all other O.D.s
**Torque Arm Length will vary from 17.38" to 19.38" depending on O.D.
being worked
***Torque Arm Length will vary from 21.25" to 22.63" depending on O.D.
being worked
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
24 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tool to avoid overload.
Read safe practices & procedures in Data Book prior to operation. Do not operate without a Data Book.
Follow OSHA, NSC, etc. standards, safe practices, & procedures.
Grip Assembly
Bolts onto
existing hanger
» Optional accessory for SURGRIP™ BELT TONG™
» Gripping areas provide added safety and convenience
during operation
» Comes with hardware for attachment
Specifications
Part No. Fits Tong Sizes Weight
SCTG SCT516, SCT1020, SCT1020H, 17 lbs.
SCT1838, SCT2036, SCT3672
SCTG614H SCT614H 17-1/4 lbs.
Gripping areas
254.675.8651 25
LEGENDARY
RELIABILITY
SINCE 1927
Bull Tongs
» Versatile tool for making up or breaking out tool and pipe joints
in the shop as well as on drilling rigs
» Non-crushing, non-jamming positive grip in downward motion
» Ratchets in upward motion
» Sizes capable of delivering up to 155,900 ft.-lbs. torque
Specifications
Part No. O.D.* Gripping Width Handle Length** Weight***
LA155-16 3-1/2" – 16" 4.38" 32" 67 lbs.
LA16H 4" – 16" 6.88" 36" 98 lbs.
LA116-C09 6" – 17" 7.55" 9" 90 lbs.
LA116-C18 6" – 17" 7.55" 18" 124 lbs.
LA116-23 6" – 17" 7.55" 23" 118 lbs.
LA116-28 6" – 17" 7.55" 28" 128 lbs.
LA116 5" – 17" 7.55" 36" 134 lbs.
LA118 5-1/2" – 20" 8.94" 48" 357 lbs.
LA118 latches with an LA120 6" – 22" 10.00" 72" 409 lbs.
adjustable chain screw
LA116H 16" – 40" 7.63" 36" 187 lbs.
nut rather than the
typical chain hook LA116HX 30-1/8" – 65-7/8" 7.56" 36" 238 lbs.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
26 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Bukup Tongs
» Originally designed for use with a pipe machine for “bucking
up” and “bucking off” tool joints
» Larger sizes are suitable for breaking out drill collars, reamers
and other heavy jobs
» Grips in upward motion, ratchets in downward motion
» Sizes capable of delivering up to 151,900 ft.-lbs. torque
Specifications
Part No. O.D.* Gripping Width Handle Length** Weight***
BA115H 2" – 8" 4.66" 48" 64 lbs.
BA116 4" – 10" 6.00" 48" 102 lbs.
BA116H 4-1/4" – 10-3/4" 6.06" 48" 151 lbs.
BA118 5-1/2" – 20" 8.94" 48" 373 lbs.
BA118 latches with an BA120 6" – 22" 10.88" 72" 546 lbs.
adjustable chain screw
nut rather than the *Chain assemblies must be ordered separately. See Chain Selection Guide on
typical chain hook product page of website.
**Call factory for torque arm lengths.
***Weights do not include chain.
WARNING! Do Not Exceed Maximum Working Load! Overloading may result in SERIOUS INJURY or DEATH!
Always use a load cell or other calibrated indicating device to monitor the line pull on the tong to avoid overload. Read
Safe Practices & Procedures Manual prior to operation. Do not operate without a manual.
Follow OSHA, NSC, etc. standards, safe practices, and procedures.
NOTE: Safe Practices & Procedures Manual can be found on pages 31-37 of this product guide.
254.675.8651 27
LEGENDARY
RELIABILITY
SINCE 1927
Hut Systems have a stainless steel, low-profile A-frame with coated heavy gauge
metal housing covering the pulley mechanism
Enclosed Assembly Systems have a fully
enclosed PVC housing for the pulley Specifications Specifications
mechanism which reduces the risk of H2S
escaping into the environment Part No. Tank Height Part No. Tank Height
Standard Hut System Enclosed Hut System
Specifications TSG6 6’ TSG6-EH 6’
Part No. Tank Height TSG8 8’ TSG8-EH 8’
Enclosed Assembly System TSG10 10’ TSG10-EH 10’
TSG8-EA 8’ TSG11 11’ TSG11-EH 11’
TSG10-EA 10’ TSG12 12’ TSG12-EH 12’
TSG11-EA 11’ TSG1212 12-1/2’ TSG1212-EH 12-1/2’
TSG12-EA 12’ TSG15 15’ TSG15-EH 15’
TSG15-EA 15’ TSG16 16’ TSG16-EH 16’
TSG16-EA 16’ TSG18 18’ TSG18-EH 18’
TSG18-EA 18’ TSG20 20’ TSG20-EH 20’
TSG20-EA 20’ TSG24 24’ TSG24-EH 24’
TSG24-EA 24’ TSG25 25’ TSG25-EH 25’
TSG25-EA 25’ TSG28 28’ TSG28-EH 28’
TSG28-EA 28’ TSG30 30’ TSG30-EH 30’
TSG30-EA 30’ Note: Standard hut systems are open at each end; Enclosed hut systems are covered at
each end and are recommended for winter climates with blowing snow conditions
28 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Capacity:
•Gears:
2" to 16" OD Pinions up to 64" in length
Up to 58" OD Gears and 20" face width
•Metrology:
(X)62" (Y)118" (Z)55"
Identifying Gears
in Pumping Unit Gear Box
Herringbone Helical
Slow Speed
Gear
Gears and pinions for many brand name pumping units and mud pumps
High Speed are available from stock including:
Gear
Slow Speed Lufkin • American • National • Cabot/CMI Baker • Gardner Denver
Pinion
High Speed
Pinion
254.675.8651 29
LEGENDARY
RELIABILITY
SINCE 1927
Gearing
Services
Full Service » Gear Milling of external involute gear forms including,
Standard & Custom but not limited to:
Gear Milling Helical – Double Helical – Spur – Herringbone
» Reverse Engineering of Standard & Metric tooth forms
» Up to AGMA 12 Quality Level (Standard 2000-A88)
» Tooth Profile Modification for prototypes or production
» Custom Metrology
» Gear Inspection Services
» Prototype Manufacturing
Capacity
» Gears:
2" to 16" OD Pinions up to 64" in length
Up to 58" OD Gears and 20" face width
» Metrology:
(X)62" (Y)118" (Z)55"
Production Equipment
DMG MORI
» DMC 160 FD duoBLOCK® – 5 axis vertical Mill-Turn
» DMU 80 FD duoBLOCK® – 5 axis vertical Mill-Turn
» CTX Beta 1250 TC Linear – 5 axis Turn-Mill
» NT 5400/1800 DCG® – 5 axis Turn-Mill
ZEISS
» PRISMO® Navigator – 3D CMM with rotary axis
30 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
SAFE PRACTICES
&
PROCEDURES MANUAL
(for Tongs and Vises with Chain)
254.675.8651 31
LEGENDARY
RELIABILITY
SINCE 1927
32 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
The service life of leaf chains can be altered by a variety As with all steel bearing surfaces, the precision, hardened steel
of adverse operating conditions. The following information joints of leaf chain require a constant film of oil between mating
discusses the most important of these conditions for parts to prevent wear and to resist corrosion.
consideration when operating or scheduling replacement of leaf
chain systems. LUBRICATION
One of the most important but often overlooked factors
OVERLOADING / SHOCK LOAD / SIDE LOADING is adequate lubrication. In addition to reducing internal
• Attempting to “inch” loads which are beyond the rated friction, maintaining a film of oil on all chain surfaces will
capacity of the tool. inhibit rusting and corrosion. This is important as corrosion of
• Striking the tool with a hammer or other object while force is highly stressed hardened steel chain components can cause
being exerted in an attempt to loosen a frozen joint. a major reduction in the load capacity of leaf chain and result
• Side pull on the chain. Side pull can be caused by pulling in link plate cracking.
or pushing on the tong in a direction that is not along
Protection from corrosion is important in storage as well as in
a perpendicular plane, unlevel mounting of the vise,
service. The factory lubricant applied to PETOL™ Chain is a
inadequate support of the part being broken out, and
“Fingerprint Neutralizing Water Displacing Corrosion
improper seating of the part being broken out in the tong
Preventive.” This is an excellent rust and corrosion inhibitor for
or vise. Improper seating will occur when the O.D. of the
chains in storage. When installing these chains new, do not
part is not consistent within the width of the tong
attempt to steam clean or degrease this lubricant. A grade of
or vise jaw.
SAE30 or 40 weight, nondetergent motor oil should be used
as supplemental lubricant and a film of this oil should
ENVIRONMENTAL CONDITIONS
be maintained on all surfaces and internal bearing joints.
Wrench and vise chains operate in widely var ying
Also,do not attempt to paint new chains. Though painting may
environments, from wet outdoor conditions to mildly or highly
help inhibit corrosion, it will seal off critical clearances
corrosive industrial atmospheres. They can also be exposed to
and restricts oil from reaching the pin surfaces where it is
abrasives such as sand and grit.
needed for good joint lubrication.
The possible effects include:
When operating in dusty environments, lubricated chains will
Moisture - corrosion and rust reduce chain strength by causing
accumulate a pastelike buildup of grime. At periodic intervals,
pitting and cracking.
this buildup should be removed by cleaning and the chain
Temperature - very cold temperatures reduce chain strength
should be immediately relubricated. Do not use caustic or
by embrittlement.
acid type cleaners; use a stiff brush and a certified safe
Chemical Solutions or Vapors - Corrosive attack of the
petroleum base solvent.
chain components grain structure and/or the mechanical
connections between the chain components (crevice corrosion)
may occur. Cracking often is microscopic. Propagation to
complete failure can be eventual or sudden.
Abrasives - Accelerated wearing and scoring of the
articulating chain members (pins and plates) may occur,
with a corresponding reduction in chain strength. Due to
inaccessibility of the bearing surfaces (pin surfaces and plate
apertures), wear and scoring are not readily noticeable.
These conditions, when coupled with normal chain wear and
inherent residual stress (normally in the chain as constructed),
can result in environmentally assisted failure.
It is impossible to predict chain life under complex conditions,
as the degree of hostility and its effects are dependent on many
variables such as temperature, time of exposure, concentration
of corrosive atmosphere or medium, degree of abrasive wear,
etc. Establishing the degree and frequency of unpredictable
dynamic loading is also difficult.
254.675.8651 33
LEGENDARY
RELIABILITY
SINCE 1927
Enlarged Holes
34 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
Safety Precautions
254.675.8651 35
LEGENDARY
RELIABILITY
SINCE 1927
INADEQUATE
SUPPORT
OF WORKPIECE
FORCE
BEING APPLIED
IS NOT IN LINE
WITH TONG
IMPROPER
SEATING OF
THE PART
DUE TO AN
INCONSISTENT
O.D.
36 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
WORKING LOAD IS THE MAXIMUM FORCE THAT MAY BE APPLIED TO A TOOL DURING
OPERATION. DO NOT EXCEED THE PUBLISHED WORKING LOADS.
CHAIN DETAIL
LENGTH
PITCH
LINK PIN
254.675.8651 37
LEGENDARY
RELIABILITY
SINCE 1927
3. Keep the wrench in the plane of the valve wheel rim when
pulling. Pulling at an angle increases the chance of slippage.
38 www.PETOL.com
LEGENDARY
RELIABILITY
SINCE 1927
NOTES
LEGENDARY
RELIABILITY
SINCE 1927
NOTES