Professional Documents
Culture Documents
Calceta - 10AE20 - Bomba - Grunfos
Calceta - 10AE20 - Bomba - Grunfos
Calceta - 10AE20 - Bomba - Grunfos
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 1 Date : Monday, 23 de April de 2018
D1-20,00 inch, D2-19,00 inch, D3-18,00 inch, D4-17,00 inch, Duty Flow 5000 US gpm
D5-15,50 inch, D6-14,50 inch 90
Duty Head 145 psi
200 80
Imp. Dia. 19,99 inch
Efficiency - %
70
Head - psi
30
20
10
Power - hp
500
400 Comments
300
200 Performance curve represents
100 typical performance. See Hydraulic
Performance document in RAPID
for perfomance test acceptance
2.000 4.000 6.000 8.000 grades/tolerances & contractual
Flow - US gpm
Flow Head Efficiency Power Required NPSH Required
(US gpm) (psi) (%) (hp) (ft)
2069,5 189,1 68,2 334,8 7,0
2553,3 186,1 74,6 371,6 7,9
3037,0 181,9 78,9 408,5 8,6
3520,8 176,3 81,7 443,4 9,7
4004,5 169,1 83,3 474,2 11,2
4488,3 160,3 84,1 499,7 13,1
4972,0 150,0 83,8 519,5 16,0
5455,8 138,2 82,3 534,9 22,4
5939,5 125,0 78,9 549,1 37,0
D1-20,00 inch, D2-19,00 inch, D3-18,00 inch, D4-17,00 inch, D5-15,50 inch, D6-14,50 inch
90
200 80
70
150 60
Efficiency - %
Head - psi
D1 50
100 40
30
D6
50 20
10
30
NPSH - ft
20
10
500
400
Power - hp
300
200
100
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 3 Date : Monday, 23 de April de 2018
Item: 1 Flow (US gpm) Head (psi) Eff. (%) Power (hp) Speed (RPM)
Model : Peerless - 10AE20
5000 145 83,8 520,45 1775
Technical Information:
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 4 Date : Monday, 23 de April de 2018
Max Work Press PSI Mech Seal 250# Disc 200°F CI 232
Max Work Press PSI Mech Seal 250# Disc 200°F DI Not Available
Max Work Press PSI Packed 125# Disch 200°F CI 162
Max Work Press PSI Packed 250# Disch 200°F CI 232
Max Work Press PSI Packed 250# Disch less than or = to 200°F DI Not Available
Max Suct Press PSI Mech Seal 125# Suct less than or = to 225°F CI (NA-T 21 Seal) 150 (T 1 Seal)
Max Suct Press PSI Mech Seal 250# Suct less than or = to 225°F CI (NA-T 21 Seal) 150 (T 1 Seal)
Max Suct Press PSI Mech Seal 250# Suct less than or = to 225°F DI Not Available
Max Suct Press PSI Packed 125# Suct less than or = to 250°F CI 150
Max Suct Press PSI Packed 250# Suct less than or = to 250°F CI Refer to the Factory
Max Suct Press PSI Pack 250# Suct 250° F DI Not Available
Max Work Press PSI Mech Seal 125# Dischg less than or = to 225°F CI 160
Max Work Press PSI Mech Seal 250# Dischg less than or = to 225°F CI 225
Max Work Press PSI Mech Seal 250# Dischg less than or = to 225°F DI Not Available
Max Work Press PSI Pack 125# Dischg less than or equalto 250°F CI 150
Max Work Press PSI Packed 250# Dischg less than or = to 250°F CI 215
Max Work Press PSI Packed 250# Dischg less than or = to 250°F DI Not Available
Shaft Diameter Through mpeller
I Inches 2,75
Shaft Dia Through Coupl
ing Inches 2,5
Cutwater Diameter Inches 21,25
Impeller Diameter at 90% of Cutwater Diameter 19,13
Impeller Diameter at 85% of Cutwater Diameter 18,06
Minimum Impeller Diameter Inches 15
Minimum Impeller Average Diameter Inches Not Applicable
WR2 Lb-Ft2 Wet Bronze Impeller 37,4
Number ofImpeller Vanes 7
Stuffing Box Shaft Sleeve Diameter Inches 3,125
Stuffing Box Bore Inches 4,375
Stuffing Box Depth Inches 4,62
Stuffing Box Face Nearest Obstruction Along Shaft In 3,06
Stuffing Box Square Packing Inches 0,625
Stuffing Box Packing Rowswithout Lantern Ring 6
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 5 Date : Monday, 23 de April de 2018
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 6 Date : Monday, 23 de April de 2018
Item: 1 Flow (US gpm) Head (psi) Eff. (%) Power (hp) Speed (RPM)
Model : Peerless - 10AE20
5000 145 83,8 520,4 1775
Typical Specification:
General: The pump(s) shall be ofthe single stage, double suction (except 2AE11 which is single suction),
horizontal split case design; split on the horiz ontal axis and shall be bronze fitted construction. Suction and
discharge connections shall be located on opposite sides of the lower casing, allowing remov al of the rotating
element without disturbing the system piping connections.
The pump(s) are to be designed for a capacity of 5000 US gpm at a total head of 145 psi, at an efficiency of 83,8%
of design condit ion.
The pump(s) shall be a Peerless Pump Company model 10AE20 and shall be of the axial split case type.
Casing: The pump casing material shall be a minimum of class 35 cast iron. Water passageways shall be smooth
to permit maximum efficiency. Casing shall be hydrostatically tested at 150% of the maximum working pressure
under which the pump could ope rate at design speed. The suction flange shall be drilled (125 lb.)(250 lb.) ANSI.
The discharge flange shall be drilled (125 lb.
) (250 lb.) ANSI.
The bearing brackets shall be cast as an integral part of the lower casing and have removable bracket caps. The
bearing housing shall be doweled for location and anti-rotation. The pump feet shall also be cast as an Integral part
of the lower casing.
Bronze renewable casing rings shall be furnished, doweled and shouldered In the casing. Ring dowels shall be
located In slots on the split surface of the lower casing.
Impeller: The impeller shall be ofone piece cast bronze, double suction type (except 2AE11 which is single
suction). The impeller shall be balanced, keyed to the shaft and fixed in an axial position by threaded shaft sleeves.
The Impeller skirt sh all be groov
ed and fit with close tolerances to the casing ring to permit a minimum of
recirculation between the impeller and he
t casing ring for maximum efficiency.
(Optional: Renewable bronze impeller ringsshall be shrunkon the impeller and lock ed in place with stainless steel
set screws. The impeller ringsshall be grooved and fit with close tolerances to the casing ring for maximum
efficiency.)
Stuffing Boxes:
Contact :
Project : Phone : Fax :
Quote No. : US-1817-88 Page No : 7 Date : Monday, 23 de April de 2018
Pack ing - The stuffing boxes shall hold a minimum offive rings of TFE packing. The bronze gland shall be split in
two halves, to facilitate removal for repacking. Gland bolts shall be ofthe swing ty pe made ofsteel with 18-8
stainless steel nuts.
Mechanical Seal - Sealing of the pump liquid cavity shall be with a face type mechanical seal with ceramic
stationary seat, carbon sealing washer, Buna rubber lexible
f members, stainless steel metal parts and spring. Seal
to be rated for 225°F(107 °C) @ 150 psig (10-34 bar) maximum. Mechanical seals shall be mounted over bronze
shaft sleeves.
Shaft and Shaft Sleeves: The shaft shall be carbon steel, adequately sized for the loads transmitted. Shaft
deflection shall not exceed .002 Inches at the face of the stuffing boxwhen operating between 95% and 105% of
capacity at best efficiency a t the pump's maximum 60 Hz. speed and wit h full diameter Impeller.The shaft shall be
protected through h t e stuffing boxby means of bronze shaft sleeves and they shall be threaded against shaft
rotationand ol cked in place with set screws. The sleeves sha ll be sealed wit h "O" rings at the Inside diameter to
eliminate leakage between the shaft and sleeve.
(Optional: Shaft shall be positively sealed against pumped fluid by means of specially machined shaft sleeves and
Impeller with sockets for use with "O" ring seals against Impeller hubs.) Shaft sleeves shall extend beyond the
packing glands (or mechanical seal flanges).
Bearings: Bearingsshall be single row,deep groov e ball type; the inboard bearing shall be arranged of r radial loads
only. The outboard bearing shall be arranged of r both radial and axial loads. Both bearings shall be grease
lubricated with grease flush through h
t e bearing hous ing (Optional: oil lube). Bearings shall be designed for an
average life of 100,000 hours.
Outboard bearing cover shall have a plugged opening for tachometer connection. Bearing housing lubric ation design
must be capable of being changed rf om grease to oil lubrication type without replacement of bearing housing or the
lower pump casing. The out board bearing shall have retaining ring retention.
Base: The pump and dri ver shall be mounted on a common steel base (with optional drip rim). Pump and driver
shall be aligned and bolted In place prior to factory shipment. Final alignment must be performed at the jobsite In
accordance with the stan dardsof the Hydraulic Institute and the pump Installation, operation and maintenance
instructions. Base Is to be grouted to eliminate vibration.
5,00 5,00
1,25 1,88
3,75 3,75
35,38
11,00
14,00 19,50
20,75
23,00
45,00
1/4" NPT GAGE CONNECTION 1/2" NPT BRACKET
SUCTION FLANGE SUCTION AND DISCHARGE DRAIN 2 PLACES
FAR SIDE ONLY 2000 LB 909 Kg PUMP WT
Dimensions in (inch)
DIESEL ENGINE
ELECTRIC MOTOR
RH ROTATION
DISCHARGE CLOCKWISE
10AE20
Dimensions in (inch)