ELYAMAN
GROUP
Product
Sales Code
EAN
Product use
Face
Product
Substance
Caliper
Elongation MD
Elongation CD
Backing
Product
‘Substance
Caliper
Tensile strength MD.
Tensile strength CD
Performance
Total caliper
Minimum labelling temperature
Service temperature
Sheet life
Storage recommendations
Information
Printabilty
Advantages:
Approvals
Approvals & Certifications
Disclaimer
Technical Information
27.08.2014 ENG 2414
RAFSTATIC PVC CLEAR 140 / NO ADHESIVE / CGL BOARD 130
‘AABINAOOI7C
6415789040415
‘Typical application are promotion and information labels, e.g. Point-
of-Sales signage, windows, sunglasses. Label can be removed or
repositioned without any residues.
RAFSTATIC PVC CLEAR 140
A clear and soft, highly plasticised PVC film. Clings by itself
(without adhesive) to clean, smooth and glossy surfaces.
172 gim* ~—_—DIN53352
14000 um DIN 53370
250% ASTM 0882
250% ASTM D882 min
CASTGLOSS BOARD 130
High gloss one side castcoated board.
130 gim’ = ISO.536
1870 um Iso 534
65 kNim — 1S0.1924
39 kNim ISO 1924
277 um
10°C
10°C to60°C
From the date of manufacture: 6 months at +20 °C and RH 50%.
Prolonged storage at higher temperatures andlor humidity levels wil
‘shorten the shelf life. Material should be printed or primered within 2
weeks of reception. For further details, please see Printability
section
‘The material is very sensitive to pressure and can gain surface
marks: + Rolls should be stored vertically + Roll lengths should be
kept less than 1000 im + Rolls should be wound with low tension
settings - PVC is sensitive to heat causing softening (increased risk
of pressure marks) and increasing plasticiser migration (reducing
printabilty ite)
= Corona treatment prior to printing and primering is strongly
recommended. - Printing should be carried out within two weeks
from the date of delivery, if primering of the material is not carried out
upon the receipt: «This is due to the migration of the plasticisers to
the surface of the material. The plasticisers affect the ink anchorage
and print quality. - Primering of the material within two weeks of the
receipt the material can extend the printable life of the product : +
Tests carried out using Fujifilm Sericol RVAQ7 UV-cured flexo primer
allowed material to be printed succesfully for up to six months The
primer will affect the surface gloss and clarity —it is recommended
to use UV flexo high gloss/high slip varnish to improve clarity and
protection + Other primers need to be tested before use - High
quality results can be achieved using UV flexo, UV screen and UV
letterpress: « Inks suitable for soft, ‘heauly plasticised” PVC need to
be used + Other printing methods need to be tested
Material does not contain DEHP plasticiser. Face material is
REACH compliant.
EN71 Part 3 - Migration of certain elements,
‘Our recommendations are based on our most current knowledge
and experience. As our products are used in conditions beyond our
control, we cannot assume any liability for damage caused through,
their use. Users of our products are solely responsible that the
product is suitable for its intended application, and have determined
‘such at their sole discretion. Users must comply with any
applicable legislation and/or testing requirements for the finished
article, and are responsible for bringing their products to market.
This publication does not constitute any warranty, express or
implied, and is intended only for the recipient and cannot therefore
be transferred to any third party. We cannot assume any liability for
the use of our products in conjunction with other materials,
{All our products are sold subject to UPM Raflatac’s general sales
conditions, and you should ensure that any existing laws are
obsened.
This publication replaces all previous versions. All information is
subject to change without notice,