I Oda. asw-sow
SOLDERPRO 80 POWER RANGE
Butane Powered SOLDERING IRON
SIMPLE-DURABLE-POWERFUL Compact Auto Ignition
‘Multi-Function Butane Powered Soldering Iron
ccessories Sold Separately)
‘APPLICATIONS WARNINGS:
* Electrica/Electronic [tis presuc. hon ed orang
Circuit Repair ‘snd tm ppcaton, can prodiee
ght Gauge Bracing | Spores
+ Light Phimbing ‘defects or othe reproductive harm,
a ry, Eyeglass -sDepartment of Transportation Hazardo®
Frame Repair “Materials Requlations forbid the carriag®
ions Ree) || emer emcnemee
7 Motlel Qatding | eRamorate
Dorot pack ts tam or anyother
+ Dental Labs tml ptm ry er
+ Thawing Frozen Locks | jicriyer tenn”
+ Heat Shrink Tubing
SPECIFICATIONS
Soh
sean ES
ach are ay
a eer cpa | emo
ei i sting
IMPORTANT SAFETY INSTRUCTIONS
Warnings:
+ Uni contains rymable gos (Butane) under
premune-use thea
+ BO NOT expose to eat above 450°C (10%) and
20d longed expose othe sun
+ BONOT puncture ores
{acess gs fo faming or ctaspubing
red may oer when the reator incre
Scio, set too ish
+ DO NOT refit ore ner ope fae,
teat, umac or combust aaa.
cep unt away rm fe and boy when ning
+ etn Won AEA CLE. Cutter rey ad
Senches ne inures
+ cer Ana FROM CHLOE
+ SORE WHEN NOT I USE. Sorin dy oda
abet out of reach of chin
+ betray aia torch fae tempratire
‘sover 300 (a0)
+ Senet ae torch fare i alot
imable im ight or song ight ;
+ WEAR SATE GLASSES
+ DONT OVERREACH exp proper footing and
balance al nes
+ SIMALERT Wetenwnatyouaredoing. se
Common tree Dont operate when you me
ted
+ D9 NOT TOUCH the ested tp obra a he
unit
+ BO NOT lo int natendd hn Ris
operating 0 ot.
+ Alay Be SURE THE UNTIS COOL BEFORE
Sonne
+ 50 NOT REPLACE CAP WIOUT STCHING
Uh OFF AND ENSURING TP HAs COOLED.
+ USE OMEYIN WELL VENTILATED AREA
+ 50 NOT atempttoreadur or repair Unt nat
See serceable: Do enue tome sexing.
store puting down 7
SOLDERING
1?
carats
(tse Te)
Ienimion
‘swTci
omy or
‘ADJUSTER
GAS TANK
+ READ INSTRUCTION MANUAL PRIOR TO USE.
+ BUTANE NOT INCLUDED.
HOW TO USE SOLDERPRO 80 —
REFUELING
21 Make sure ON / OF snitch sat OFF poston before
fill
2.2 Adaptors are not normaly rquite when fli
253 ore ode ean as pictured (ful wanstrs
dependent upon gr
24 Stop fling when oveow ge,
IGTion wanwancs
3,ADo not toch tp tip housing or knuried rut while
igniting
'3.8Do not ignite the unit when Tp Assembly isnot
screwed on
{HOW TO USE SOLDERING IRON
3.1.1 Set gas cont evel a mld postion.
3.12 Push the ON OF ignition switch slowly upward
towardtpto the max point and release the sth
(e031) oy
3.13 You may hear the sound of gas ling and then i
the tip hausing window wl gow range ater
Vor2 seconds W not repeat3.1.2
3.1.4 Tip temperature can be changed by adjusting the
gascortrel iver
3.15 Te tumoff, pul ignition switeh down tothe | (.
OFF positon it isnot necesaryto move the gss |
contol lever after the unit tuned of
{WOW To USE BLOW TORCH
312.1 Remove tip and tip housing by
untghteing Knurled Nut
3.22 Mount the same tip housing in place
without tip
3.23 ignite gas by means of ona igniton
switch (Same as above.
3.24 Adjust flare length, Do not adst to
‘maximum length 35 gas may fare up
And turn of
3.25 To shutoff the unit, refer to 1.5)
HOW To USE HEAT BLOW TP
23.3 Same as soldtng tp.
HOW TO USE HOT KNIFE TP
3.4 Same as soldering tp.
‘ADWsTMENT a
4.1 Thetip temperature canbe acustes by turing the
{GAS CONTROL LEVER observing the ~ + signs on
the body.
4.2 daly set the GAS CONTROL LEVER to mid
positon when saiderng
4.3 isnot necessary forthe catalyst inside the tp to
‘low bright re to achive saislactry soldering +
‘empertues Experience al dictate the adjuster
setting reqines.‘UANGING TPS
5.1 Be sure the tp has cooled before remove
5.2 The catalyst eon through the Hot Air Exhaust
Hole of the soderng tis is very dlate and
wl ot sstein mechanical abuse without 3
seco damage
5.3 The soldering tip is easly removable allowing |
the nstalaon of others tips othe
replacement of 8 worn tin, Ate the soldering
tipi coo, simaly unscrew it witha
counterackvise motion. Be crea not to
‘vertighten a this could damage the nazle
assembly and tread in the body
--=