Professional Documents
Culture Documents
USB-Output (Computer):
1.1 SPECIFICATION
This connects RX2SIM to the computer and also supplies power to RX2SIM. Connect
• Operating Voltage: 3.8V – 6.0V (typical 5.0V) RX2SIM either by plugging it into a USB socket of the PC directly or by using a stan-
• Satellite port: 3.3V, max. 100mA (unlimited) dard type A USB extension cable. If the connection is made through a USB hub, the
• Dimensions (LxWxH): 92 x 42 x 20 mm hub should provide a separate power supply in order to avoid current overload of
• Weight: 32g the PC’s USB port in case more than one USB device is active at the same time.
PPM
PPM OUT
Output SRXL, PPM-serial signal (SPPM) or you can also connect one single Spektrum®
(Dongle)
OUT
USB - DSM2/DSMX remote satellite or a JR® RJ01 DMSS satellite.
AUX
MODE
MODE Output In general the receiver does not need a separate power supply as RX2SIM supplies 5V
Equipment
PPM
RC Equipment
(Computer) power to the receiver. Other devices (like servos) must not be connected to the
SRXL
Finest RC
receiver in order to avoid excessive current consumption! To prevent damage to
USB - SBUS Input
SINGLEchannel
CHANNELS
RX2SIM or to the USB port the output current is limited to 100mA at port [- + 1]. If
RX 2SIM
Input
USB
USBPPM OUT
DSM2
DSM2
(Dongle) DSMX
your receiver requires higher current or voltage you must power it separately. In this
–– ++ 11 22 33 4 5 66 77 88 case the (+) pole (red wire) between receiver and RX2SIM must be cut or
AUX unplugged to prevent from damaging the USB port due to overvoltage.
MODE
Finest RC Equipment
PPM
SRXL PPM-Output: ground signal
Spektrum® This connector outputs the control signals
RC Equipment
Finest RC Equipment
SBUS SINGLE CHANNELS
DSM2/DSMX to your simulator interface. The functionality
–– ++ 11 22 3 4 5 66 77 88
CHANNELS
remote satellite
JR® DMSS RX2SIM
DSMX
– + 1 2 3 4 5 6 7 8
matches the trainer port of your RC transmitter.
3,5mm phone jack, 2-pole (mono)
Input
MODE
Here you can connect the USB interface or dongle of your simulator software. In
Finest RC Equipment
PPM
RX 2SIM
SRXL operating mode “Simulator-Dongle”, RX2SIM connects this port with the computer’s
RX2SIM
• PPM SBUS SINGLE CHANNELS USB port. In operating mode “Game Controller”, this port is not active. If needed,
connect your simulator dongle to another USB port of your computer.
SBUS
PPM
SRXL
AUX
USB
DSM2
• SRXL
RX2SIM
DSMX
DSM2
DSMX
DSM2
• S.Bus / S.Bus2
PPM OUT
– + 1 2 3 4 5 6 7 8
• USB2SYS
AUX 2.1 CONNECTING A RECEIVER WITH SEPARATE SERVO OUTPUT CHANNELS
MODE
Finest RC Equipment
PPM
PPM OUT
PPM OUT USB
USB SRXL
Servo SBUS SINGLE CHANNELS three-wire patch cable. This connection also supplies voltage for the receiver.
single channels
USB
DSM2
Connect channels 2 to 8 using the 7-wire patch cable. On these servo plugs only the
DSMX
– + 1 2 3 4 5 6 7 8
signal line (orange wire) is connected.
Finest RC Equipment
Please refer to your receiver’s manual or the imprint on its case to determine which
pin is the impulse line on each servo connector.
This instruction manual only applies to the latest RX2SIM firmware version! – + K1 K2 . . . . . . . . . . . . K8
Perform a firmware update with the StudioX software prior the first usage.
2.1 CONNECTING A RECEIVER WITH SEPARATE SERVO OUTPUT CHANNELS 2.2 RECEIVER WITH S.BUS, S.BUS2, SRXL OR SERIAL PPM PORT 2.3 SPEKTRUM® OR JR® REMOTE SATELLITE
–– ++ 11 22 3 4 5 66 77 88
CHANNELS
CHANNELS
Patch cable
SINGLEchannel
SINGLEchannel
–– ++ 11 22 3 4 5 66 77 88
–– ++ 11 22 3 4 55 66 77 88
(3-wire) S.Bus, S.Bus2
Input
Input
Input
or
RC Receiver Satellite cable
MODE
MODE
MODE
MODE
MODE
SRXL-Receiver
MODE
or (3-wire) Spektrum®
RX2SIM
RX2SIM
RX2SIM
RX2SIM
satellite
RX2SIM
Receiver with
RX2SIM
serial PPM signal
SBUS
PPM
SRXL
or
AUX
SBUS
PPM
SRXL
AUX
SBUS
PPM
SRXL
AUX
JR® RJ01
DSM2
DSMX
DSM2
DSM2
DSMX
DSM2
DSMX
DSM2
DSMX
DSM2
Functional description: Functional description: satellite
PPM OUT
PPM OUT USB
USB The control signals are transmitted separately (one line The control signals are transmitted through the patch PPM OUT
OUT USB
Functional description:
PPM OUT
PPM OUT USB
USB PPM USB
for each servo channel) from the receiver to RX2SIM, cable from the receiver to RX2SIM, which forwards the The control signals are transmitted from the satellite
which forwards the controls via USB to the computer as controls via USB to the computer as game controller to RX2SIM, which forwards the controls via USB
game controller axes and buttons. axes and buttons. to the computer as game controller axes and buttons.
Patch cable
CHANNELS
CHANNELS
CHANNELS
SINGLEchannel
SINGLEchannel
SINGLEchannel
–– ++ 11 22 3 4 5 66 77 88
–– ++ 11 22 3 4 5 66 77 88
–– ++ 11 22 3 4 5 66 77 88
S.Bus, S.Bus2
(3-wire) or
Input
Input
Input
MODE
MODE
RC Receiver
MODE
MODE
MODE
MODE
or (3-wire) Spektrum®
RX2SIM
RX2SIM
RX2SIM
RX2SIM
RX2SIM
RX2SIM
SBUS
SBUS
PPM
SRXL
PPM
SRXL
AUX
AUX
SBUS
PPM
SRXL
AUX
JR® RJ01
DSM2
DSMX
DSM2
DSMX
DSM2
DSM2
DSM2
DSMX
DSM2
satellite
PPM OUT
PPM OUT USB
USB PPM OUT
PPM OUT USB
USB PPM OUT
PPM OUT USB
USB
RX2SIM
RX2SIM Unused operating modes can be disabled so you don’t have to skip them anytime
PPM
PPM OUT
Orange: USB2SYS when switching between operating modes. Likewise, disabled modes can be enabled
OUT AUX again. Press and hold the button while connecting RX2SIM to the computer. Hold
In this mode RX2SIM acts as BEASTX USB2SYS interface and can be used as
Equipment
MODE
MODE
RC Equipment
PPM the button until the Mode LED shows the color of the mode you wish to enable or
communication interface for MICROBEAST/MICROBEAST PLUS. Connect the 3-wire
disable. To enable the mode release the button while the blue LEDs are on. To disa-
patch cable to the very left port at RX2SYS marked [- + 1]. The other end of the cable
Finest RC
SRXL
Finest
connects to the SYS port of MICROBEAST/MICROBEAST PLUS. Watch out for correct SBUS Input
SINGLEchannel
CHANNELS
polarity! Note: You mustn‘t connect any servos to MICROBEAST when RX2SIM is
USB
USB
DSM2
DSM2
used to power the device. Otherwise when MICROBEAST is powered by a DSMX
DSMX
separate power supply (i. e. for power the servos) this must not provide more –– ++ 11 22 3 4 5 66 77 88 DECLARATION OF CONFORMITY
than 6V output voltage! Otherwise RX2SIM or the computer‘s USB port will get
damaged. So when you power MICROBEAST with a higher voltage level disconnect This device conforms to the basic requirements and other relevant
or cut the (+) pole (red wire) between RX2SIM and SYS port. regulations of corresponding CE directives.
Single servo channels The original Declaration of Conformity can be found on the Internet
at www.rcware.de at the respective product description.