Professional Documents
Culture Documents
Operation Manual: Split Type Room Air Conditioner
Operation Manual: Split Type Room Air Conditioner
OPERATION MANUAL
HSU-12CR03-Y
HSU-18CR03-Y
Please read this operation manual before using the air conditioner.
0010515222
Downloaded from www.Manualslib.com manuals search engine
Downloaded from www.Manualslib.com manuals search engine
Cautions
Disposal of the old air conditioner Safety Instructions and Warnings
Before disposing an old air conditioner that Before starting the air conditioner, read the
goes out of use, please make sure it's inop- information given in the User's Guide caref-
erative and safe. Unplug the air conditioner ully. The User's Guide contains very impor-
in order to avoid the risk of child entrapment. tant observations relating to the assembly,
operation and maintenance of the air
It must be noticed that air conditioner system conditioner.
contains refrigerants, which require speciali-
zed waste disposal. The valuable materials The manufacturer does not accept respon-
contained in an air conditioner can be recycled sibility for any damages that may arise due
.Contact your local waste disposal center for to non-observation of the following
proper disposal of an old air conditioner and instruction.
contact your local authority or your dealer if
you have any question. Please ensure that Damaged air conditioners are not to be
the pipework of your air conditioner does not put into operation. In case of doubt, consult
get damagedprior to being picked up by the your supplier.
relevant waste disposal center, and contribute
Use of the air conditioner is to be carried
to environmental awareness by insisting on an
out in strict compliance with the relative
appropriate, anti-pollution method of disposal.
instructions set forth in the User's Guide.
o o
Maximum:D.B/W.B 35 C/24 C
Indoor Minimum:D.B/W.B 18 C/14oC
o
Cooling o o
Maximum:D.B/W.B 46 C/27 C
Outdoor Minimum: D.B o
18 C
Installation
WARNING
Please call Sales/Service Shop for the Installation.
Do not attempt to install the air conditioner by yourself because improper works
may cause electric shock, fire, water leakage.
lnstallation in a inadequate place may cause accidents. Do not install in the following place.
CAUTION
Connect the earth Do not install in the Do not get the unit Check proper
cable. place where there is exposed to vapor installation of the
any possibility of or oil steam. drainage securely
inflammable gas
leakage around the
unit.
earthing
STRICT
PROHIBITION PROHIBITION ENFORCEMENT
OFF STRICT
ENFORCEMENT
Connect power supply cord Use the proper voltage Do not use power supply cord
to the outlet completely extended or connected in halfway
STRICT STRICT
ENFORCEMENT PROHIBITION
ENFORCEMENT
Do not use power supply cord Take care not to damage Do not insert objects into the air
in a bundle. the power supply cord. inlet or outlet.
Do not start or stop the Do not channel the air flow directly Do not try to repair or reconstruct
operation by disconnecting at people, especially at infants or by yourself.
the power supply cord and so on. the aged.
PROHIBITION PROHIBITION
CAUTION
Do not use for the purpose of storage of Take fresh air occasionally especially Do not operate the switch with
food, art work, precise equipment, when gas appliance is running at the wet hand.
breeding, or cultivation. same time.
STRICT
PROHIBITION ENFORCEMENT PROHIBITION
Do not install the unit near a fireplace Check good condition of the Do not pour water onto the unit
or other heating apparatus. installation stand for cleaning
Outdoor unit
Remote controller
Display board
NOTE: 1.Cooling only unit do not have functions and displays related with heating.
2.The CODE button on this remote controller is not available.
Confirmation indicator:
After pressing power ON/OFF, if no display, reload the batteries.
Note:
Full display or unclear display during operation indicates the batteries have been used up.
Please change batteries.
Used two new same-typed batteries when loading.
If the remote controller can't run normally during operation, please remove the batteries and
reload several minutes later.
Hint:
Remove the batteries in case unit won't be in usage for a long period. If there are any display
after taking-out, just need to press reset key.
Display board
1.Unit start
Press ON/OFF on the remote controller, unit starts.
Remote controller
Display board
1. Unit start
Remote controller Press ON/OFF on the remote controller, unit starts.
3.Select temp.setting
Press TEMP. button
PURIFY
Display board
1. Unit start
Press ON/OFF on the remote controller, unit starts.
Remote controller 2.Select operation mode
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
3.Select temp.setting
Press TEMP. button
Every time the button is pressed, temp.setting
increase 1oC, if kept depressed, it will increase
PURIFY
rapidly
FRESH
Every time the button is pressed, temp.setting
decrease 1oC,if kept depressed, it will decrease
POWER/SOFT
rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as
follows:
Remote controller:
LOW MED HI AUTO
10
Display board
PURIFY
3.Select temp.setting
Press TEMP. button
FRESH
Every time the button is pressed, temp.setting
increase 1oC,if kept depressed, it will increase
POWER/SOFT
rapidly
Every time the button is pressed, temp.setting
decrease 1oC,if kept depressed, it will decrease
rapidly
Select a desired temperature.
4.Fan speed selection
Press FAN button. For each press, fan speed changes as
follows:
Remote controller:
LOW MED HI AUTO
COOL operation starts when room Air conditioner is running under displayed fan speed.
Ultra-low air flow
temp.is higher than temp.setting.
In DRY mode, when room temperature becomes
lower than temp.setting+2oC,unit will run intermittently
Temp.setting+2oC
Temp.setting
at LOW speed regardless of FAN setting.
5.Unit stop
On reaching temp.setting +2oC
unit will run in mild DRY mode. Press ON/OFF button, the unit stops.
11
Display board
1. Unit start
Remote controller Press ON/OFF on the remote controller, unit starts.
2.Select operation mode
Press MODE button. For each press, operation mode
changes as follows:
Remote controller:
PURIFY
Remote controller:
POWER/SOFT
LOW MED HI
4.Unit stop
Press ON/OFF button, the unit stops.
12
Pos.2 Pos.2
PURIFY
Pos.3 Pos.3
FRESH
Pos.4 Pos.4
Pos.5
POWER/SOFT
Pos.5
Pos.6
Pos.6 (Auto swing)
Pos.7
Pos.8
AUTO:
remote controller: Pos.1 Pos.2 Pos.3 Pos.4 Pos.5 Pos.6
13
Display board
Operation
Before going to bed, you can simply press the
SLEEP button and unit will operate in SLEEP SLEEP operation starts SLEEP operation stops
mode and bring you a sound sleep. Approx.6hrs
PURIFY
14
Display board
Hints:
After replacing batteries or a power failure happens, time setting should be reset.
Remote controller possesses memory function, when use TIMER mode next time,
just press SET button after mode selecting if time setting is the same as previous one.
15
Display board
16
POWER Operation
Remote controller
When you need rapid cooling, you can use this function.
BLANK
POWER SOFT
SOFT Operation
You can use this function when silence is needed for rest
or reading.
Hints:
During POWER operation, in rapid COOL mode, the room
will show inhomogeneous temperature distribution.
Long period SOFT operation will cause effect of not too cool.
17
outlet grills of the air conditioner are opened, and the unit
goes on working under the condition before the setting of
health airflow function.
After stopping, the outlet grille will close automatically.
Notice: Cannot pull direct the outlet grille by hand. Otherwise,
the grille will run incorrectly. If the grille is not run correctly,
stop for a minute and then start, adjusting by remote controller.
Note:
1 .After setting the health airflow function, the position of inlet
and outlet grills is fixed.
2.In cooling, it is better to select the mode.
3.In cooling and dry, using the air conditioner for a long time
under the high air humidity, a phenomenon falling drips of
water occurs at the outlet grille .
4.Select the appropriate fan direction according to the actual
conditions.
18
Timer
Temperature Operation Designated Air flow
mode temperature mode
Test operation
operation.
When the remote controller is manipulated, it gets the system back to the
normal operation mode.
19
Proper
temperature
During cooling
operation prevent
the penetration of
direct sunlight with
curtain or blind
OFF
20
WARNING
Before maintenance,be sure to turn off the system and the circuit breaker.
O O
Gasoline,benzine, thinner or cleanser may Hot water over 40 C(104 F) may cause
damage the coating of the unit. discoloring or deformation.
21
Common sense:
In order to keep the AIP layer having a highly work effect ,it should be cleaned regularly or
aperiodically just according to the working environment.
1. Turn off the A/C electricity supply and make sure that AIP layer is not working.Then clean the
AIP layer after turning off it five minutes later.
2. Please brush off the dust on AIP board,then steep it into cleaning agent water and wash it.
3. After cleaning AIP board pleas put it on a dry place until it is totally dry.
4. Ensure AIP board is dry enough then install it in the its position along the slide way .
Make sure it is as before and could work well.
The AIP layer will be replaced in fixed time. In normal family, it will be replaced every 6 months.
In the use, please note to clean the filter frequently (take off the back suction cleaner or lightly pat it)
to avoid the operating effect is lowered due to the dust covering the filter. AIP layer and bacteria-killing
medium filter is strictly prohibited from being cleaned by water.
The the bacteria-killing medium filter not in use should be stored in shade, cool and dry place.
Please don't expose it to the sunlight for a long time otherwise the degerming performance will drop.
22
23
Caution
EARTHING
4. Plug-in
Caution
24
25