CONGRESS TOOLS CO., INC.
68 Great Hil Road
‘Naugatuck, CT 08770
(208) 723-1424
MATERIAL SAFETY DATA SHEET
tapping Compounds are designed to deposit a film of the product on a rotating
tool of plate (lap) by frictional heat The “charged® lap when placed in
contact with workpieces removes material to improve surfaces. According to
Department of Transportation Regulations, these materials are considered non-
hazardous and non-toxic in shipping, use and storage.
SHIPPING NAHE
MOCO Lapping Compounds
#2, #9, P-L-M
‘ NMFC N.@.1, #33440
Congress P/N ULLA Lapping
Section II Ingredients/Identity Information
es Soop
‘COMPONENT(S) CHEMICAL NAME MAPPROX) iF ureciand w Cantstoert
Fatty Acids & Glycerides N/A No
Fatty Acids & Glycerides 68953-33-3 32 to'51 | N/A Wo
Fatty Acids & Glycerides $55-43-1 32 to 57 | WA Wo
Petroleum Oils '8009-03-8 9to 2 | NA Wo
‘Aluminum Oxide Abrasive (dust) 1344-28-1 36 to 57 [Wm | __No
F f
——
PHYSICAL DATA Specific Gravity more than 1.2
White or gray soft paste - Mild waxy odor Insoluble in water 2
Packaged in jars or cans Melting point: 38° to 45° ¢
FIRE AND EXPLOSION DATA
Flash point over 350° F. = Auto ignition temp. 300° C. - Flammable limits not
applicable. Compound subject to abnormally high temperatures may form carbon
monoxide. In case of fire, use water fog, dry chemical or carbon dioxide.
Water may cause violent frothing requiring full facepiece and self-contained
breathing apparatus. NFPA Healfh hazard > Not estabiicncd”
HEALTH HAZARD DATA TLV (Total mass for dust while using) 10.0 mg/m
jr Th case of contact with eyes, rinse with plenty of water for at
least 15 minutes, Wash skin with soap and water. If swallowed,
induce vomiting by sticking ringer down tnroat. never give aayinis
by mouth to anyone unconscious or suffering convulsions.SPECIAL PROTECTION INFORMATION
Gime malarial ip belig used, cultable exhaust equipment is required with eye protec-
‘Son, clothing and gloves to prevent compound dust or materials being removed during
the buffing operation from entering the nose, throat or skin of the buffer. See rec-
commanded environmental monitoring.
'Y DATA
and hazardous polymerization wil not occur. Incompatibility exists
with strong alkalies like sodium hydroxide, ™ ve
$2 AUTIONS
ae bony from heat.
SPILL PROCEDURE AND WASTE DISPOSAL TREATMENT
ee epi owsop aabeclad ‘Into containers. Buffing wheal wastes may contain whee!
‘int which is combustible. Dispose of in accordance with regulations.
RECOMMENDED ENVIRONMENTAL MONITORING
The U.B. De] ENTE Giaeetionand Welfare - National Institute for Oooupations
ypartmant 5
Safety & Health (NIOSH) has publicetions to assist in maintaining a safe environment, asr
Norasive Metal Finishing, Itam 1733-00122-7, U.S, Printing Office, Washington, DC
20402
Ventilation Requirements for Grinding, Polishing & Buffing €277-332/3. National
‘Technical Information Seryics, Springfield, VA 22161
Industrial Ventilation - A Manval of Recommended Practices, American Conference
Gf Governmental Industrial Hygenists, P.O, Box 16153, Lansing, MI 48902.
‘this Material Safety Data Sheet contains all available pertinent information to enable yo
fo comply with environmental regulations af the “Resource Conservation & Recovery Act of
Te7e"s with the identification of eny material which could contribute hazardous charec-
teristics to a waste stream oc be hazardous in ite pure form, thereby enabling you to
properly follow the regulations for starage, labeling and disposal of ite waste.
Unises specifically indicated on this Material Safety Data Sheet, our products
A. Is not an oxidizer.
B Dosa not have @ flash point Jass than 60° C, (140° F.)
C. Is not potentially explosive,
D. Does not react violently with water,
B, Does not generate toxic gases when mixed with water.
F. Does not contain any currently defined carcinogenic material,
G. Does not contain:
arsenic Lead Nickel Halogenated Solvent.
Barium Mercury Any other Heavy Metal Non-Haloganated Solvent
Cadmium Selenium Cyanide Phosphates
Chromium Silver Sulfur Chelating Agents
H, Does not contain any toxic organics as defined by 40 CFR, parts 413 and 433.
FOR ANY FURTHER INFORMATION REGARDING THIS PRODUCT, CONTACT
CONGRESS TOOLS CO., INC.
51 Great HIS Road
Naugatuck, CT 05770
(20@) 723-1424