Professional Documents
Culture Documents
TESTING
EQUIPMENTS
W W W . B E S M A K L A B . C O M
CONCRETE 5 - 32
CEMENT 33 - 46
SOIL 47 - 68
ROCK MECHANICS 69 - 78
AGGREGATE 79 - 92
ASPHALT 93 - 108
“
CONCRETE COMPRESSION MACHINES AND ACCESORIES
COMPRESSION MACHINES
A compression test determines behavior of materials under crushing loads. The specimen is compressed and deformation at
various loads is recorded. There are two types of frame in available as 4- Columns type or Wall type.
8 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
Wall Type
• Fully compliant with BS EN 12390-4 and ASTM C39 in terms of Force measurement and the
stringent stability, alignment & restraint requirements of the Load Frame.
• Compact Welded steel load frame with a high degree of mechanical stability.
• Ball-seated upper platen feature.
• Lower platen, positively located on the loading ram, marked to allow centring of both cubes and
cylinders.
• Loading ram with cover to prevent debris damaging it during testing and a limit switch to prevent
it from exceeding the maximum limit of travel.
• Frame fitted with mesh guards at front and rear to protect the operator.
• Front guard is hinged for ease of access.
Piston stroke 50 mm 50 mm 50 mm 50 mm
Thickness of platens 45 mm 45 mm 45 mm 45 mm
Loading rate 0.5-20 kN/s 0.5- 20 kN/s 0.1-25 kN/s 0.1-25 kN/s
Dimensions: 500 x 675 x 1310 mm 500 x 675 x 1310 mm 505 x 410 x 1030 mm 520 x 450 x 1100 mm
www.besmaklab.com 9
CONCRETE COMPRESSION MACHINES AND ACCESORIES
SPECIFICATIONS:
• Weight : 71 kg
• 230 V / 50 Hz.
SPECIFICATIONS:
• Weight : 71 kg
• 220 V / 50 Hz
10 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
SPECIFICATIONS:
www.besmaklab.com 11
CONCRETE COMPRESSION MACHINES AND ACCESORIES
Modulus of Elasticity:
LVDT is used to measure the deformation on the specimen. 2 LVDT must be assembled vertically and 1 LVDT must be assembled
horizontally to the compressometer.
Machine automatically calculates modulus of elasticity, poisson rate, vertical and horizontal deformation by LVDTs and
compressometer.
Linearity Over
Measuring Range Repeatability Total Travel mm Operating Force Max.
Measuring Range
12 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
Controller Features:
BESMAK BCO-S Series Testing Machines are controlled by DOLI EDC DOLI EDC 220 Fits For;
220 controller unit and RMC-7 handheld unit.
a) The EDC220 has a load channel with a resolution
• Data Acquisition and Control System DOLI – EDC 220: of ±180,000 steps and an incremental position
channel with a controlled ±10Volt output for power
EDC controller is imported from Germany and widely used for testing
amplifiers.
machine with high configuration or requirements. EDC220 is a built-
in unit without keys and display and has been designed for static b) Further load cells, LVDTs, strain gauges, exten-
and dynamic testing instruments. It features as stable control, high someters,2-channel-incremental-extensometers, se-
accurate measuring and high sampling rate (1 kHz~5 kHz) etc. Also, rial controlled extensometers, safety shields, further
it can self-identify & self-calibration functions. Up to now, it is the I/Os, synchronizing several EDCs in a multi-channel
most reliable device to be used extensively for static and dynamic application.
testing machines.
c) Digital control; Closed Loop Control
All measuring channels for a basic testing instrument, as well as an
output channel to control an actuator, are on- board. The EDC220V d) Connection with RS 232 and Ethernet
has two I2-Bus-Extension-Slots for e.g. extensometers. The on- e) Interface to PC, printer
board load channel of the EDC220V has a resolution of ±180,000
steps. f) Display of outputs (stand-alone)
k) Data-logging (stand-alone)
RMC-7 is a handheld unit (cable 3m) connected directly to the EDC. The RMC-7 has a magnetic foil on its back and therefore can
be placed at an ergonomic position.
RMC-7 handheld unit has an emergency stop button onto it (the red button at the right top). In case of an emergency situation,
process can be easily stopped.
RMC-7 handheld unit provides to control and monitor Test Speed Adjustment, Grips Position Control, Active Crosshead Control
(up-down movement speed), Load/Deformation, Extension, Real-Time % Extension. Automatically stops when the piston
reaches to maximum displacement point etc.
www.besmaklab.com 13
CONCRETE COMPRESSION MACHINES AND ACCESORIES
• 32Bit-Program
• Simple and intuitive operation
• Customized and field-proven applications
• All protocols and printouts freely definable
• “Free Programming Module” for individual tests
• Compatible to each EDC system from DOLI
• Export into ASCII or EXCEL files
• Almost all applications possible in the testing lab
• Use as production testing system in online mode, also
• Integrated graphics
• Integration of several additional channels possible
• Direct connection of thickness gauges, calipers and other measurement instruments via RS232
• Fast and reasonable testing
• Connection types are Ethernet and RS-232
SPECIFICATIONS:
Product Code : BCO-113/7
Power : 220 V, 50 Hz.
Dimension : 450 x 850 x 1400 mm
14 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
COMPRESSOMETER-EXTENSOMETER
COMPRESSOMETER
It is used to evaluate deformation and strain characteristics of concrete cylinders
while undergoing compression testing. The Compressometer includes two cast
aluminum-alloy yokes, mounting and central points, stainless steel control rods.
Models are available with a dial gauge as well as with a digital indicator.
COMPRESSOMETER – EXTENSOMETER
The measure both axial deformation and diametrical extension of cylinder
specimens under compression stress, by determining the elastic modulus.
Supplied with Dial Gauge or LVDT
SPECIFICATIONS:
Product Code : BCO-122/1* Ø 100 – 125 – 150 mm
BCO-122/11 Ø 42 – 54 – 76 mm
SPECIFICATIONS:
Product Code : BCO-115/1 for cylinder samples
BCO-115/2 for cube samples
BCO-115/3 for cobblestone samples
Sizes up to a length of 320 mm, up to a width of 80 mm and heights of 60 to 160 mm
www.besmaklab.com 15
CONCRETE COMPRESSION MACHINES AND ACCESORIES
FLEXURAL MACHINES
Flexural frames can be used with a wide range. The frame supports a hydraulic ram and upper sub-platen assembly incorporating a
spherical seating. The upper and lower sub-platens will accept various specimen loading bearers, which are supplied separately.
Frames can be detached from hydraulic unit and connected to any hydraulic unit in laboratory.
Specifications:
Dimensions 505 x 400 x870 mm 845 x 840 x 1215 mm 1290 x 1000 x 1290 1370 x 670 x 2210
(lxwxh) (lxwxh) mm (lxwxh) mm (lxwxh)
Weight 350 kg 460 kg
16 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
SPECIFICATIONS:
• Weight : 71 kg
• 230 V / 50 Hz.
www.besmaklab.com 17
CONCRETE COMPRESSION MACHINES AND ACCESORIES
SPECIFICATIONS:
18 www.besmaklab.com
COMPRESSION MACHINES AND ACCESORIES CONCRETE
SPECIFICATIONS:
• 240*120 pixel blue-white graphic LCD display Sample reports observable and printable
www.besmaklab.com 19
CONCRETE COMPRESSION MACHINES AND ACCESORIES
SPECIFICATIONS:
• Backlight function
• Two analogical and two digital channels, use for load cell or pressure transducer etc.
• Load-Time, Tensile-Time, Test Results and Sample reports observable and printable.
• One RS232 serial port for connecting either PC or printer for data transmission
20 www.besmaklab.com
NON DESTRUCTIVE TESTING OF HARDENED CONCRETE CONCRETE
EN 12504-2, ENV 206, DIN 1048 part 2, BS 1881 Part 202, ASTM C805, ASTM D5873 (Rock), D5873,
JGJIT 23-2001, JJG 817- 1993
Accurately measuring compressive strength- which directly determines the load bearing capacity and durability of concrete
structures- is achieved by striking th concrete at a defined energy, the measuring the hammer’s rebound. The rebound
corresponds to the concrete’s hardness. Using conversion tables, the rebound value can be correlated to compressive strength.
This instrument enables engineers to measure the strength of existing concrete structures in situ to control concrete quality
and detect weak spots.
SPECIFICATIONS:
Product Code : BCO-116/201 – BCO-116/202 Original Schmidt
Weight : Type N/L : 1.8 kg,
Dimensions : Type N/L: 140 x 114 x 324 mm
SPECIFICATIONS:
Product Code : N Type: BCO-116/501 ST model Silver Schmidt
BCO-116/503 PC model
L Type: BCO-116/502 ST model
BCO-116/504 PC model
SPECIFICATIONS:
Product Code : BCO-116/601 ND Type Digi Schmidt
BCO-116/602 LD Type
www.besmaklab.com 21
CONCRETE NON DESTRUCTIVE TESTING OF HARDENED CONCRETE
SPECIFICATIONS:
Product Code : BCO-116/13
ASTM C876-91, BS 1881 Part 201, SIA 2006, DGZfP B3, UNI 10174
The Canin instrument offers two methods for investigating and assessing the corrosion of steel in concrete. Firstly, the
instrument can measure the corrosion potential and secondly, it can measure the resistivity of the concrete. The same CANIN
device can perform both tasks.
SPECIFICATIONS:
Product Code : BCO-116/401 Canin with rod electrode
BCO-116/402 Canin with rod and wheel electrode
BCO-116/403 Canin with wenner Probe
BCO-116/404 Canin with rod and wheel electrode and wenner probe
22 www.besmaklab.com
FRESH AND HARDENED CONCRETE TESTS CONCRETE
SPECIFICATIONS:
Accessories:
SLUMP SET
EN 12350-2, BS 1881-102, ASTM C 143, AASHTO T119,
It is used to measuring slump of freshly mixed concrete for the determination of
consistency, medium and high workability. The concrete is levelled off with the top
of the slump cone, the cone removed and the slump of the sample is measured.
SPECIFICATIONS:
Product Code : BCO-101 Set
BCO-101/2 Plate
BCO-101/3 Funnel
Weight : 7 kg (Set)
www.besmaklab.com 23
CONCRETE FRESH AND HARDENED CONCRETE TESTS
FLOW TABLE
SPECIFICATIONS:
Product Code : BCO-102 Set
BCO-102/1 Flow Table
BCO-102/2 Flow Cone
BCO-102/3 Wooden Hammer
BGE-604 /Trowel
BGE-605/Meter Rule
Weight : 22 kg (Set)
SPECIFICATIONS:
Product Code : BCO-105
Weight : 16 kg
Dimensions : 150 x 330 x 330 mm
24 www.besmaklab.com
FRESH AND HARDENED CONCRETE TESTS CONCRETE
SPECIFICATIONS:
Product Code : BCO-107
Weight : 35 kg
Dimensions : 1290 x 610 x 264 mm
WALTZ CONTAINER
EN 12350-4, DIN 1048, UNI 9420
Waltz Container is used for determining the degree of compactability and
consistency of fresh concrete. It consists of metal box with two handles. Box is
electrostatic dyed.
SPECIFICATIONS:
Product Code : BCO-104
Weight : 5 kg
Dimensions : 200 x 200 x 400 mm (w x d x h)
www.besmaklab.com 25
CONCRETE FRESH AND HARDENED CONCRETE TESTS
These tests are used to determine the flowability and passing ability of self-consolidated concrete (SCC), ASTM C1621. Passing
ability refers to the ability of SCC, under its own weight (without vibration), to flow into and completely fill the spaces within
intricate framework, containing obstacles such as reinforcment bars.
BCO-128
Weight: 12 kg
26 www.besmaklab.com
FRESH AND HARDENED CONCRETE TESTS CONCRETE
ACME PENETROMETER
SPECIFICATIONS:
Product Code : BCO-119/2
Weight : 27 kg
VEBE TIME
EN 12350-3, ASTM C1170, UNI 9419
This is a variation of the slump test, in this method the sample is subjected to
sinusoidal vibration. It includes a determination of the workability of concrete.
The assembly is mounted upon a small vibrating table operating at a fixed
amplitude and frequency.
SPECIFICATIONS:
Product Code : BCO-103 Vebe Set
: BCO-103/1 Cone
: BCO-101/4 Tamping Rod 16 x 600 mm
: BGE-606/ Stopwatch
Power : 220V 50Hz
Weight : 50 kg
Dimensions : 600 x 470 x 750 mm
www.besmaklab.com 27
CONCRETE FRESH AND HARDENED CONCRETE TESTS
EN 12390-2
Pan type mixer is suitable for the mixing concrete in the laboratory. It is designed
to give efficient mixing of both dry and wet materials. The mixing pan is removable
and tilts for easy access to the pan and emptying on completion of the mixing
operation. It is rotated by a turntable driven by a protected electric motor.
It consist of mixer with pan, edge and mixing blades, rubber wheels, reductor.
SPECIFICATIONS:
Product Code : BCO-108/1
Total Capacity : 100 Liters
Mix Capacity : 56 Liters
Motor : 1,5 kW
Power Supply : 220V, 50 Hz
Weight : 245 kg
Dimensions : 1200 x 1000 x 900 mm
VIBRATING TABLE
EN 12390-2, BS 1881:108
It is a compact unit providing controlled vibro-compaction. Vibrating table mounted
on a steel stand, supplied with clamp assembly. It is used for homogenous
compaction of concrete moulds. Available in two models which capacities are 2
and 4 moulds.
SPECIFICATIONS:
Product Code : BCO-109/ 1 2 pcs BCO-109/2 4 pcs
Weight : 80 kg 160 kg
Dimensions : 625x 320 x 700 mm 1250 x 650 x 700 mm
Power : 220 V 50 Hz 220 V 50 Hz
28 www.besmaklab.com
FRESH AND HARDENED CONCRETE TESTS CONCRETE
CONCRETE MOULDS
Moulds are manufactured in accordance with dimensions and tolerances stated in the related
standards.
CUBIC MOULDS
Different sizes of cube moulds available with their specifications are:
SPECIFICATIONS:
Product Code : BCO-120/1 BCO-120/2 BCO-120/3 BCO-120/5 BCO-120/4
Dimensions : 100x100x100 mm Metal 100x100x100 mm Plastic 150x150x150 mm Metal 150x150x150 mm Plastic Import 150x150x150 mm Plastic
Weight : 8.5 kg 0.8 kg 15.5 kg 1 kg 1 kg
CYLINDER MOULDS
Different sizes of cylinder moulds available with their specifications are:
SPECIFICATIONS:
Product Code : BCO-120/7 BCO-120/14 BCO-120/8 BCO-120/9
Dimensions : 100 x 200 mm Steel Import 100 x 200 mm Plastic Import 150 x 300 mm Steel Import 150 x 300 mm Plastic Import
Weight : 8 kg 8 kg 15 kg 2 kg
BEAM MOULDS
Different sizes of beam moulds available with their specifications are:
SPECIFICATIONS:
Product Code : BCO-120/10 BCO-120/11 BCO-120/12 BCO-120/13
Dimensions : 100 x 100 x 500 mm Steel 150 x 150 x 600 mm Steel 150 x 150 x 750 mm Steel 100 x 100 x 400 mm Steel
Weight :
www.besmaklab.com 29
CONCRETE FRESH AND HARDENED CONCRETE TESTS
POKER VIBRATOR
EN 12390-2, BS 1881:108
It is used as an internal means of vibratory compaction. A number of vibrations are achieved when the poker is inserted to the
concrete, which gives grater density. High performance and ideal for form work and interior work. Long life and high amplitude.
Shoulder carry on.
SPECIFICATIONS:
Product Code : BCO-109/3
Motor : 0,75 KW - 3000 rpm
Vibration : 12000 v.p.m
Shaft Lenght : 1m/2m/3m/4m
Bottle Dia. : 32 mm
Weight : 6,5 kg
Dimensions : 2 meter shaft, 38 mm diameter bottle
CURING TANK
SPECIFICATIONS:
Product Code : BCO-110 /1
Dimensions : 610 x 610 x 508 mm
Weight : 55 kg
Power : 220 V, 50 Hz
Product Code : BCO-110 /2
Dimensions : 650 x 2000 x 640 mm
Weight : 74 kg
Power : 220 V, 50 Hz
Product Code : BCO-110 /3
Dimensions : 815 x 1650 x 530 mm
Weight : 74 kg
Power : 220 V, 50 Hz
30 www.besmaklab.com
FRESH AND HARDENED CONCRETE TESTS CONCRETE
MELTING POT
SPECIFICATIONS:
Product Code : BCO-132/1 Besmak BCO-132/2 Impact BCO-132/3 Humboldt
Capacity : 3L 6L 3,8 L
Temperature Range : 0-250 °C
Power : 220 V / 50 Hz
Weight : 9 kg
CAPPING OF CYLINDERS
EN 12390-3, ASTM C31, C192, C617, AASHTO T23, T126
It is used for flattening cylindrical sample surfaces.
Comes with standard apparatus for 75, 100, 150 mm diameter.
SPECIFICATIONS:
Product Code : BCO-118
Weight : 12 kg
Dimensions :
SPECIFICATIONS:
Product Code : BCO-117/1 Electrical Model 360° tilting ,Milwaukee motor
BCO-117/101 Stand
BCO-117/2 Electrical Model fixed, Milwaukee motor
BCO-117/3 Electrical Model fixed, Bosch motor
BCO-117/301 Stand
Bits : BCO-117/4 Drill Bit Ø 75 mm
BCO-117/5 Drill Bit Ø 100 mm
BCO-117/6 Drill Bit Ø 150 mm
Core Drill Height: 10-50 mm
Speed : Two speed 450 rpm , 900 rpm
Power Supply : 220 V AC, 50 Hz
Weight : 85 kg
Dimensions : 700 x 410 x 1200 mm
www.besmaklab.com 31
CONCRETE FRESH AND HARDENED CONCRETE TESTS
BUOYANCY BALANCE
EN 12390-7, BS 1881:114
It is used for specific gravity determination of concrete or aggregates.
The density of concrete specimens are determined by dimensional checks, weighting and calculation or weight in air/water
buoyancy method.
Comes with sample plate ,water tank and wire basket.
Electrostatic dyed.
The balance must be ordered seperately!
SPECIFICATIONS:
Product Code : BCO-111 Set
BGE-607 Wire Basket
BCO-111/1 Sample Plate
BCO-111/2 Water Tank 380 x 240 x 280 mm
Weight : 42 kg
Dimensions : 970 x 500 x 400 mm,
32 www.besmaklab.com
CEMENT
36 • AIR CONTENT AND DENSITY
37 - 38 • CONSISTENCY, SETTING TIME AND WORKABILITY
39 - 45 • SAMPLE PREPARING, CURING AND STRENGHT
46 • FINENESS
“ W H AT I S C E M E NT ?
“
CEMENT AIR CONTENT AND DENSITY
SPECIFICATIONS:
Product Code : BCE-306
Weight App. : 6 kg
LE CHATELIER FLASK
Capacity 250ml.
SPECIFICATIONS:
Product Code : BCE-301
Weight App. : 227 g
36 www.besmaklab.com
CONSISTENCY, SETTING TIME AND WORKABILITY CEMENT
PLUNGER PENETROMETER
SPECIFICATIONS:
Product Code : BCE-304
Weight App. : 7 kg
Table: Cast-bronze: 254 mm diam. , combined weight with shaft: 4.1 ±0.05 kg
Flow Mold: Machined bronze: 69.8 mm top i.d. x 101.6 mm base i.d. x 50.8 mm h.
SPECIFICATIONS:
Product Code : BCE-314
Dimension : 254 mm dia x 254 mm h
Weight App. : 10 kg
www.besmaklab.com 37
CEMENT CONSISTENCY, SETTING TIME AND WORKABILITY
VICAT APPARATUS
EN 196-3:2005 - EN 13279-2 (GYPSUM) - EN 480-2 - ASTM C187 -
ASTM C191 - AASHTO T131 - DIN 1196 - DIN 1168 - BS 4550
MANUAL TYPE
Used for determination of setting time and consistency of cement. Mould,
Beginning, Ending and water content needles are included.
SPECIFICATIONS:
Product Code : BCE-305/1
Weight App. : 6 kg
AUTOMATIC TYPE
The Vicat apparatus, that is designed and manufactured using the most recent
and sophisticated technology, is used for the initial and final setting time
determination of cements or mortar pastes.
The unit is manufactured with anticorrosion and tropicalized components to be
used in places with humidity not below 90% and 20°C. controlled temperature as
required by EN Specifications.
The entire test is made in a fully automatic way and gives a very precise and
repeatable result. The results are printed on the incorporated printer and this
eliminates the manual operations of installing and zeroing the paper graph on
the drum.
SPECIFICATIONS:
Product Code : BCE-305/OT
Power supply : 220-240V 1 Ph 50Hz.
Dimension : 400 x 200 x 470mm
Weight App. : 13 kg
REACTION CONTAINER
ASTM C289
For determining potential alkali reactivity of aggregates (chemical method)
when used with high alkali cements. Stainless steel unit is 2” dia. x 2-1/4” high
(51mm dia. x 57mm) fitted with air-tight cover. 50-75ML capacity.
SPECIFICATIONS:
Product Code : BCE-320
Dimension : 51 mm dia. x 57 mm h
Weight App. : 2 kg
38 www.besmaklab.com
SAMPLE PREPARING, CURING AND STRENGHT CEMENT
SPECIFICATIONS:
Product Code : BCE-312/3
Power : 220 V, 50 Hz.
Dimension : 450 x 850 x 1400 mm
Weight App. : 400 kg
SPECIFICATIONS:
Product Code : BCE-313/1 Compression Jig BCE-313/2 Flexural Jig
Dimension : 200 x 200 x 210 mm 205 x 210 x 205 mm
Weight App. : 15,25 kg 7,25 kg
www.besmaklab.com 39
CEMENT SAMPLE PREPARING, CURING AND STRENGHT
EDC controller is imported from Germany and widely used for testing a) The EDC220 has a load channel with a resolution
machine with high configuration or requirements. EDC220 is a built- of ±180,000 steps and an incremental position
in unit without keys and display and has been designed for static channel with a controlled ±10Volt output for power
and dynamic testing instruments. It features as stable control, high amplifiers.
accurate measuring and high sampling rate (1 kHz~5 kHz) etc. Also,
it can self-identify & self-calibration functions. Up to now, it has b) Further load cells, LVDTs, strain gauges, exten-
been the most reliable device to be used extensively for static and someters,2-channel-incremental-extensometers, se-
dynamic testing machines. rial controlled extensometers, safety shields, further
I/Os, synchronizing several EDCs in a multi-channel
All measuring channels for a basic testing instrument, as well as an application.
output channel to control an actuator, are on- board. The EDC220V c) Digital control; Closed Loop Control
has two I2-Bus-Extension-Slots for e.g. extensometers. The on-
board load channel of the EDC220V has a resolution of ±180,000 d) Connection with RS 232 and Ethernet
steps.
e) Interface to PC, printer
k) Data-logging (stand-alone)
DOLI RMC – 7 Handheld Unit:
RMC-7 is a handheld unit (cable 3m) connected directly to the EDC. The RMC-7 has
a magnetic foil on its back and therefore can be placed at an ergonomic position.
RMC-7 handheld unit has an emergency stop button onto it (the red button at the
right top). In case of an emergency situation, process can be easily stopped.
RMC-7 handheld unit provides to control and monitor Test Speed Adjustment,
Grips Position Control, Active Crosshead Control (up-down movement speed), Load/
Deformation, Extension, Real-Time % Extension. Automatically stops when the
piston reaches to maximum displacement point etc.
40 www.besmaklab.com
SAMPLE PREPARING, CURING AND STRENGHT CEMENT
• 32Bit-Program
• Simple and intuitive operation
• Customized and field-proven applications
• All protocols and printouts freely definable
• “Free Programming Module” for individual tests
• Compatible to each EDC system from DOLI
• Export into ASCII or EXCEL files
• Almost all applications possible in the testing lab
• Use as production testing system in online mode, also
• Integrated graphics
• Integration of several additional channels possible
• Direct connection of thickness gauges, calipers and other measurement instruments via RS232
• Fast and reasonable testing
• Connection types are Ethernet and RS-232
SPECIFICATIONS:
Product Code : BCE-312/3
Power : 220 V, 50 Hz.
Dimension : 450 x 850 x 1400 mm
Weight App. : 400 kg
www.besmaklab.com 41
CEMENT SAMPLE PREPARING, CURING AND STRENGHT
FEATURES:
• Product Code: BCO-113/4 be entered respect to the standards
• 240*120 pixel blue-white graphic • Load-Time, Tensile-Time, Test
LCD display Results and Sample reports observable
• High resolution 65.000 points and printable.
Const. Address
Techician (Sampler)
Technician (Tester)
SAMPLE INFORMATION
SPECIFICATIONS: 6DPSOLQJ'DWH 5HSUHVHQWHG6WXFWXUH(OHPHQW
EXPERIMENT RESULT
Dimension : 640 x 700 x 1440 mm Sample Age No Experiment Density Weight (gr) Max. Load(KN) Stress(Mpa)
Date (gr/cm3)
42 www.besmaklab.com
SAMPLE PREPARING, CURING AND STRENGHT CEMENT
MORTAR MIXER
SPECIFICATIONS:
Product Code : BCE-308
Power supply : 220 V, 50 Hz.
Dimension : 650 x 600 x 380 mm
Weight App. : 85 kg
ASTM C190 - ASTM C307 - AASHTO T132, EN 196-1 - EN ISO 679, BS 4550
Manufactured from steel and completely galvanized. For Compression strength
tests of Portland cement, mortars.
SPECIFICATIONS:
Product Code : BCE-311/1 40x40x40mm, Cube Mould
BCE-311/2 50x50x50mm, Cube Mould
BCE-311/3 70.7x70.7x70.7mm, Cube Mould
BCE-311/5 40x40x160mm
(Available in 3 Gang and 1 Gang model) Prism Mould
CLIMATE CHAMBER
SPECIFICATIONS:
Product Code : BCE-316
Power supply : 220V 50 Hz.
www.besmaklab.com 43
CEMENT SAMPLE PREPARING, CURING AND STRENGHT
BS 4550
The mould is mounted on a vibration platform with excentric mechanism.
Used to prepare cement samples at cube moulds.
Conforming cube mould dimension is 70.7*70.7*70.7mm.
SPECIFICATIONS:
Product Code : BCE-310
Power supply : 220V 50 Hz
Dimension : 300 x 900 x 500 mm
Weight App. : 80 kg
JOLTING TABLE
SPECIFICATIONS:
Product Code : BCE-309
Power supply : 220 V 50 Hz.
Dimension : 395 x 1050 x 275 mm
Weight App. : 85 kg
44 www.besmaklab.com
SAMPLE PREPARING, CURING AND STRENGHT CEMENT
LE CHATELIER MOULD
SPECIFICATIONS:
Product Code : BCE-302
Weight App. : 30 g
EN 196-3 - BS 6463
Constructed with stainless steel inside chamber and exterior
case in painted steel sheet, it can hold up to 12 Le Chatelier
moulds (to be ordered separately) in the removable rack,
supplied with the bath.
The bath reaches the boiling point in approx. 30 minutes. Now
an original device keeps the bath temperature at the boiling
point, by avoiding the water evaporation and assuring that Le
Chatelier moulds remain covered by the water during all the test
execution.
SPECIFICATIONS:
Product Code : BCE -301-A
Power supply : 230V 1ph 50/60 Hz 1800 W
Dimension : 405x265x205 mm
Weight App. : 7 kg
www.besmaklab.com 45
CEMENT FINENESS
SPECIFICATIONS:
Product Code : BCE-307/1
Power supply : 220-240V 1 50Hz.
Weight App. : 6.8 Kg.
EN 933-10
Effective single sieve for dry powders, fragile samples or material
that can’t be wet sieved, Micron air-jet sieve shaker uses 200mm
dia. sieve drums, with 2mm to 20μ particle size range. Unit adapts
to 75mm diameter electro-formed sieves in 90mm drums for 45μ to
5μ. Timer and vacuum controls allow reproducibility of the results.
Filter attachment, micromesh sieve or cyclone collector accessories
may be used to recover fines.Includes 200mm cast aluminum sieve
drum housing unit, Plexiglas lid, 15W slotted brass air nozzle, 0-15
minute rotary timer switch, 1HP vacuum power system, gauge and
9.5 gal. recoverable capacity, steel filter canister.
SPECIFICATIONS:
Product Code : BCE-315
Power supply : 220V 50 Hz
Weight App. : 50 kg
46 www.besmaklab.com
SOIL
60 - 62 • SOIL CLASSIFICATION
67 • SOIL PERMEABILITY
“
SOIL SOIL STRENGHT
Humboldt provides an extensive line of triaxial testing equipment solutions for today’s soil labs. At the heart of our triaxial
testing equipment is the Humboldt Concept of providing a modular system of interchangeable, stand-alone components that
when combined creates highly-versatile systems. This modular concept allows you to easily create a custom solution for your
needs, as well as having the ability of taking advantage of upgrades and new technology, while not being locked into an
obsolete proprietary system. Presented below and on the following pages are three triaxial systems based around our HM-3000
and HM-2900 load frames.
50 www.besmaklab.com
SOIL STRENGHT SOIL
www.besmaklab.com 51
SOIL SOIL STRENGHT
SPECIFICATIONS:
Product Code : BSO-222 (Automatic)
BSO-223 (Manual)
BESMAK is the only official dealer of Humboldt in Turkey. Manual Pressure Control System
52 www.besmaklab.com
SOIL STRENGHT SOIL
Accesories:
Dial Gauge 12 x 0,002 mm or 10 x0,01 mm,
Cell Sets 50 mm or 75 mm,
Porous Discs 50 mm or 75 mm,
Weight Set
SPECIFICATIONS:
Product Code : BSO-220
Weight : 25 kg
Dimensions : 190 x 850 x 527 mm
www.besmaklab.com 53
SOIL SOIL STRENGHT
54 www.besmaklab.com
SOIL STRENGHT SOIL
FEATURES
• Microprocessor controlled digital stepper motor
• Control via the digital display with keyboard
• Return datum facility
• Fully steplessly variable speed over the range of 0.00001 to 9.99999mm/minute
• RS232 port
• Forward/reverse travel limit switches
• Will accept either analogue or digital measuring devices
ACCESSORIES,
Load Ring 3 kN capacity,
Shear box set 60 mm²,
Shear box set 100 mm²,
Extrusion tool,
Dial Gauge 0,002 mm precision for vertical,
Dial Gauge 0,01 mm precision for horizontal.
Weight Set 50 kg,
Weight hanger,
Device Weight: 90 kg
Dimension:
SPECIFICATIONS:
Product Code: BSO-221
POCKET VANE
ASTM D 2573
Used to quickly find shear strength of binding materials of soil in laboratory or field
conditions. It permits the determination of a large number of strength values with
different orientation of failure planes.
Direct reading dial as Kgf/cm2. Measuring range: 0-1 Kgf/cm2 Complete with
stainless steel vane.
SPECIFICATIONS:
Product Code : BSO-219/1 Plastic, BSO-219/2 Metal
Weight : 300 gr.
Dimensions : 120 x 160 x 50 mm
www.besmaklab.com 55
SOIL SOIL BEARING CAPACITY
SPECIFICATIONS:
Product Code : BSO-208-M
Power : 220 V 50 Hz.
Weight : 80 kg
Dimensions : 400 x 610 x 1270 mm
SPECIFICATIONS:
Product Code : BSO-208-D
Power : 220 V 50 Hz.
Weight : 80 kg
Dimensions : 400 x 610 x 1270 mm
SPECIFICATIONS:
Product Code : BSO-208-3
Power : 220 V 50 Hz.
Dimension : 400 x 605 x 960 mm
Weight : 70 kg
56 www.besmaklab.com
SOIL BEARING CAPACITY SOIL
SPECIFICATIONS:
Product Code : BSO-209 Set
Weight : 29 kg
SPECIFICATIONS:
Product Code : BSO-210
Comes with swelling plate, tripod, 10 mm capacity 0,01 mm precision dial gauge.
Water tank is optional.
Weight : 1,5 kg
The CBR (California Bearing Ratio) field test set is designed for making CBR determinations in the field and is built around a
modified Load Frame. Typically, the reaction load used for field testing is a heavy piece of equipments such as a loaded dump
truck. The set includes 1 of each of the following: H-Gear Box w/ handle, Swivel Base; 2200 lbf Load Ring; 5500 lbf Load Ring;
Penetration Piston - 4”; Extension Set; Extension Set; Dial Indicator 1.000” x .001”; Extension Points - 1” length; Magnet Holder
w/ swivel; Steel Bridge Support – 8 ft., and 2 of H-Surcharge Weight and Surcharge Weight.
SPECIFICATIONS:
Product Code : BSO – 212-A
www.besmaklab.com 57
SOIL SOIL BEARING CAPACITY
SPECIFICATIONS:
PRODUCT CODE : BSO – 212
SPECIFICATIONS:
Product Code : BSO-217
Weight : 25 kg 42 kg
58 www.besmaklab.com
SOIL BEARING CAPACITY SOIL
Used to determine the bearing capacity of subgrades, or to measure soil compaction. Light
and easy to handle in the field. A rapid means of determining the penetration resistance of
soil in shallow exploration surveys. Includes: 30°, 1 sq. in. (6.45 sq cm) cone; 250 lb. (1.1kN)
capacity proving ring; brake type dial indicator, holds final reading until manually released;
3/4” (19mm) dia. shaft, graduated at 6”, (152mm) intervals; 3/4” (19mm) dia. extension rod,
graduated at 6” (152mm) intervals; cast aluminum T-handle.
SPECIFICATIONS:
Product Code : BSO-202/7
Weight : 6,8 kg
Including:
1 piece of fixing bar
1 piece of 100 kN or 300 kN capacity lifting jack
1 piece of hand pump
1 piece of pressure gauge (max. 280 bar)
3 pieces of 50 mm x0.01 mm deformation dial gauges and holders
4 pieces of 150, 253, 305, 455 mm diameter plates
SPECIFICATIONS:
Product Code : BSO-213
Weight : 95 kg
Dimensions : 460 x 1240 x 400 mm
www.besmaklab.com 59
SOIL SOIL CLASSIFICATION
MANUAL TYPE
Hand-operated liquid limit machine features mechanical revolution counter attached to the shaft to register the number of
drops in the liquid limit cup.
SPECIFICATIONS:
Product Code : BSO-201/1
Complete with Grooving Tool made of brass /
Dimensions : 120x140x110 mm
Weight : 3 Kg
MOTORIZED TYPE
Motorized liquid limit machine gives uniform testing with greater degree of accuracy . Unit is comprised of manual liquid limit
machine with geared motor to give proper operating speed and automatic counter. Machine is attached to metal plate with
rubber feet. Includes grooving tool and gauge block.
SPECIFICATIONS:
Product Code : BSO-201/2
Power Supply : 220V 1PH 50Hz Dimensions: 140x170x110 mm
Weight : 4.5 Kg
60 www.besmaklab.com
SOIL CLASSIFICATION SOIL
SPECIFICATIONS:
Product Code : BSO-202/2
Weight : 17 kg
Dimensions : 250 x 380 x 574 mm
SPECIFICATIONS:
Product Code : BSO-203
Accessories
1 piece of 300 x 300 mm glass plate
1 piece of 3 mm diameter x 20 cm length stainless stell rod
1 piece of Porcelein pot
1 piece of elastic spatula
6 pieces of 75 mm diameter x 30 mm height sample box
www.besmaklab.com 61
SOIL SOIL CLASSIFICATION
SPECIFICATIONS:
Product Code : BCE-319/1 Color Standard Chart
BCE-319/2 Graduated Bottle
BCE-319/3 Sodium Hydroxide
SPECIFICATIONS:
Product Code : BSO-227
62 www.besmaklab.com
SOIL DENSITY AND MOISTURE SOIL
SPECIFICATIONS:
Product Code : BSO-207
Weight : 113 kg
Dımensions : 335 x 510 x 1505 mm
Power : 220 V 50 Hz
SPECIFICATIONS:
Standard Proctor Rammer,
Product Code : BSO-206/1
ASTM : 2.5 kg with a 12” (305 mm) drop,
BS : 2.5 kg with a 300 mm drop
www.besmaklab.com 63
SOIL SOIL DENSITY AND MOISTURE
SPECIFICATIONS:
Product Code : BSO-214/1 6 inches sand density set (plastic)
BSO-214/2 8 inches sand density set (metal)
BSO-214/2 12 inches sand density set (metal)
Accesories:
Sample bags and ties
Pocket dial thermometer
Bristle brush
Stainless steel spoon
Steel chisel
Rubber mallet
Density sand
EN 13286-46, BS 1377
following tests:
Moisture Condition Value
Chalk Crushing Value
MCV is used in construction control to assess the suitablity of soil works material
in relation to specified upper limits of moisture content. For performing to Moisture
Condition Value and Chalk Crushing Value Tests.
Comes with1 piece of vernier caliper, 6 pieces of fibre discs, mould and counter.
SPECIFICATIONS:
Product Code : BSO-211
Weight : 60 kg
Dimensions : 300 x 640 x 960 mm
64 www.besmaklab.com
SOIL DENSITY AND MOISTURE SOIL
HS-5001EZ Moisture/Density Gauge is just that— easy. Easy to operate, easy to power and easy to service. The EZ gauge
features a menu-driven control panel with easy-to-use, built-in test routines and auto features, making testing a quick and
accurate operation. It also features our innovative trigger release handle that eliminates pinched fingers while providing
smooth operation. Available in 8” (200mm) and 12” (300mm) lengths with either 1” (25mm) or 2” (50mm) increments, the
EZ gauge provides a single gauge solution to density and moisture measurements. The EZ’s versatility allows it to measure
density through direct transmission and backscatter modes, as well as including thin lift and trench modes, as well as moisture
determinations. The gauge uses an advanced micro-processor-based technology to provide highly-accurate measurements of
density and moisturethat are automatically computed for direct readouts of wet density, dry density, moisture content, percent
of moisture, percent of compaction (Proctor or Marshall), void ratio and air voids. The EZ Gauge complies with all pertinent
standards: ASTM D6938, D2950, C1040 and AASHTO T310. The gauge is calibrated by the Five-block calibration method.
SPECIFICATIONS:
Product Code : BSO-218
15 sec, 1 min and 4 min test times.
99% accuracy.
LCD backlight for night use.
Temperature detector for safety.
Can be recharged in field.
Weight : 41 kg
Dimensions : 600 x 585 x 355 mm
Power : 220 V 50 Hz.
www.besmaklab.com 65
SOIL SOIL DENSITY AND MOISTURE
PROCTOR PENETROMETER
ASTM D1558
Establishes the moisture-penetration resistance relations of fine-grained
soils. Includes these interchangeable needles (area in cm2): (6.45), (4.84),
(3.22), (2.15), (1.29), (0.65), (0.32) (0.22) and (0.16).
The unit consists of a special calibrated spring dynamometer with a
pressure-indicating scale on the stem of the handle. The device is capable
of measuring the penetration force with an accuracy of 62 lbf [10 N] and
shall have a capacity of at least 130 lbf [600 N].
SPECIFICATIONS:
Product Code : BSO-216
Accessories
9 pieces of 6.45, 4.84, 3.22, 2.15, 1.29, 0.65, 0.32, 0.22, 0.16 cm2 needles.
SPECIFICATIONS:
Product Code : BSO-228
Weight : 6 kg
66 www.besmaklab.com
SOIL PERMEABILITY SOIL
SPECIFICATIONS:
Product Code : BSO-215/1 Constant Head Permeability Test Set
Including : 1 m stand with 3 tubes and meter scale, water tank, transpalent cells (1 piece 75 mm,1 piece 114 mm)
www.besmaklab.com 67
SOIL SOIL PARTICLE SIZE DISTRIBUTION
SPECIFICATIONS:
Product Code : BSO-205
Weight (Set) : 19 kg
Dimensions : 300 x 630 x 530 mm
SPECIFICATIONS:
Product Code : BSO-204
Power : 220 V,50 Hz
Weight : 13 kg
Dimensions : 400 x 870 x 330 mm
68 www.besmaklab.com
ROCK
MECHANICS
“
ROCK MECHANICS CLASSIFICATION AND STRENGHT
BESMAK Pressure Gauge Indicator gives results with different units; kN, N, t, kg, bar.
The system has a digital display that continuously monitors applied load and direct reading of
specimen diameter. It is portable and light design. Tester accepts core specimens up to 101.6 mm
(4) in diameter.
SPECIFICATIONS:
Product Code : BRC-704
Dimension : 400 x 530 x 720 mm
Weight : 24 kg
ROCK HAMMERS
ASTM D 5873
This device is used for nondestructive strength testing of rock. The hammer is designed for testing thin walled structural
components with a thickness of less than 100 mm or rock cores.
Measuring range 10 to 70 MPa (1,450 to 10,152 psi). The rebound value is read directly from the scale. Used the test Nx, Ax
and Bx samples. Rock cradle is advised as optional for vertical testing.
SPECIFICATIONS:
Product Code : BRC-703
Dimension : 140 x 114 x 324 mm
Weight : 1.8 kg,
72 www.besmaklab.com
CLASSIFICATION AND STRENGHT ROCK MECHANICS
Weight
LCD graphics data acquisition and controls system SEMATRON is designed Load/Time Graph
to control the machine and processing data from load cells or pressure
transducers installed on the compression machine frame. Easy to read LCD
graphics display and touch-button data pad keys make the unit quick and
straight forward to operate. All interactions with the measuring system are
via the front control panel by using simple menu-driven procedures. The
SEMATRON is contained in light alloy housing and it’s design satisfies the
ergonomic requirements for various use. The SEMATRON digital allows real
time load us time graph. At the end of the test cycle, the results can be stored
in the large memory or downloaded to a PC in SEMATRON software format.
Dedicated software package is available for further online data processing
data base management and certificate printing.
Test Report
www.besmaklab.com 73
ROCK MECHANICS CLASSIFICATION AND STRENGHT
SPECIFICATIONS:
• 240x120 pixel blue-white graphic LCD display • Load-Time, Tensile-Time, Test Results and Sample reports
observable and printable.
• High resolution 65.000 points
• RS232C (optional Ethernet) connection at 57600 band
• Backlight function
• One RS232 serial port for connecting either PC or printer for
• Capability of contrast calibration by light. data transmission
• 18 key touch membrane keyboard • Comes with Connection cable and software.
• CPU card by microprocessor 32 bit ARM risk architecture • Large permanent memory up to 256 test results
• Two analogical and two digital channels, use for load cell or • Easy to operate with 6 main function keys
pressure transducer etc.
• Language select, English - Turkish
• Standalone full automatic testing capacity
• Can control two frames
• Can make manual tests if requested
• A sample type and dimension can be entered respect to the
standards
Hoek Cell
Hoek cells comprise a steel body and two steel end caps which are screwed to the body of the
cell when in use. The body have two self sealing couplings; one of them is for connecting to the
hydraulic pressure system, the other one is for de- airing the cell chamber and for the attachment
of pressure measurement device. Four sizes are available: AX, 1.5 in, BX and NX nominal core
sizes.
Hoek Cells
30 mm 42 mm 55 mm 1.5 in
Membranes
Membranes are different sizes for 30 mm, 42 mm, 55 mm, 1.5 in dia samples.
Membranes
Specifications 30 mm 42 mm 55 mm 1.5 in
74 www.besmaklab.com
CLASSIFICATION AND STRENGHT ROCK MECHANICS
Servo hydraulic Constant Pressure System which is controlled by SEMATRON, it is designed to supply
required oil to hoek cell. It can load a specimen between 0, 01 Bar/sec. to 30 Bar/sec. at set time Also
servo controlled hydraulic system is equipped with full automatic closed loop controlled hydraulic servo-
valve system.
SPECIFICATIONS:
• Dimensions: 550x1300x1050 mm, • Micro filter with mechanic dirt display,
• Weight: 80 kg, • Feed back control,
• Servo valve controller, • Pressure limit valve,
• Valves are imported, • Used imports transducer for pressure sensor with
+/- 1% precision,
• Can adjust speed automatically,
• Can connect to any unit in the laboratory,
• Can keep the pressure constant during desired
period, • 220 V / 50 Hz,
• Electric multi-piston hydraulic pump installed in oil • Comes with LCD screen.
tank,
Modulus of Elasticity:
www.besmaklab.com 75
ROCK MECHANICS SAMPLING AND PREPERATION
SPECIFICATIONS:
Product Code : BRC-701
Power supply : 220 V AC, 50 Hz
Dimension : 700 x 410 x 1200 mm
Weight : 85 kg
SAMPLE EXTRUDER
SPECIFICATIONS:
Product Code : BRC-706
Dimension : 70x55x110 mm
Weight : 25 kg
76 www.besmaklab.com
SAMPLING AND PREPERATION ROCK MECHANICS
MASONARY SAW
SPECIFICATIONS:
Product Code : BRC-702/1 Junior BRC-702/2 Small BRC-702/3 Senior BRC-702/3 Major
Lenght (mm) : 1100 1100 1400 -
Width (mm) : 600 600 600 -
Height (mm) : 750 750 850 -
Blade Dim. (mm) : 450 350 350 600
Max. Cutting (mm) : 175 110 110 250
Cutting Lenght (mm) : 600 700 1100 650
Motor Power (V) : 5.5-380 3-220-380 4-380 5.5-380
Weight (kg) : 80 75 145 90
Wet Cutting Motor (V) : 0.50-220 0.50-220 0.5-220 0.5-220
ASTM D4644
This apparatus provides a means of predicting the
durability of rock to weakening and disintegration when
subjected to the simulated effects of climatic shaking and
used to test distribution of rock samples in water. Facility
to test up to four sets of samples. Quick coupling for
assembly and removal of drums.
The apparatus consists of a motor driven unit mounted
on a base board with quick-release drive assemblies.
These are capable of revolving two or four corrosion
resistant specimen test drums with 140 mm diameter
and 4 mm stainless steel mesh at 20 rpm. The test drums
are supported on water lubricated bearings allowing SPECIFICATIONS:
unobstructed clearance below the drum and are supplied Product Code : BRC-705
with two water troughs. Power supply : 220V 50 Hz
www.besmaklab.com 77
ROCK MECHANICS SAMPLING AND PREPERATION
General features;
Lower unit with drawer which pulls out to collect the abrasive
grit.
Grinding wheel made of special steel (vertical) with direct drive
via a gear motor.
Adjustable quick fastening device with jointed lever storage
silo with supply funnel fixed on a stand.
Counter weight (14 kg) via suspended cable in the lower unit.
Electric control in waterproof housing built-in revolution counter
from 0 – 99,000.
SPECIFICATIONS:
Product Code: BRC-709/1 BRC-709/2
Power Supply: 220 V 50 Hz 220 V 50 Hz
Weight app: 275 kg 250 kg
78 www.besmaklab.com
AGGREGATE
86 - 87 • MECHANICAL PROPERTIES
88 • CHEMICAL TESTS
“
AGGREGATE PARTICAL SIZE AND SHAPE
SIEVES
SPECIFICATIONS:
Product Code : BGE- 657, 200 mm dia. BGE- 659, 300 mm dia.
Weight App. : 3 kg
SIEVE SHAKER
SPECIFICATIONS:
Product Code : BGE-611
Power supply : 220V 50 Hz
Dimension : 500 x 504 x 1050 mm
Weight App. : 86 kg
82 www.besmaklab.com
PARTICAL SIZE AND SHAPE AGGREGATE
FLAKINESS SIEVES
BS 812
Used to determine particle size shape or geometrical
characteristics of the aggregates.
SPECIFICATIONS:
Product Code : BAG-402
BAG-402/1 : 4,9 mm slot
BAG-402/2 : 7,2 mm slot
BAG-402/3 : 10,2 mm slot
BAG-402/4 : 14,4 mm slot
BAG-402/5 : 19,7 mm slot
BAG-402/6 : 26,3 mm slot
BAG-402/7 : 33,9 mm slot
GRID SIEVES
Consist of 40-31,5-25-20-16-12,5-10-8-6,3-5-4-3,15-
2,5 mm sizes.
SPECIFICATIONS:
Product Code : BAG-401
BAG-401/1 40 mm slot BAG-401/8 8 mm slot
BAG-401/2 31,5 mm slot BAG-401/9 6,3 mm slot
BAG-401/3 25 mm slot BAG-401/10 5 mm slot
BAG-401/4 20 mm slot BAG-401/11 4 mm slot
BAG-401/5 16 mm slot BAG-401/12 3,15 mm slot
BAG-401/6 12,5 mm slot BAG-401/13 2,5 mm slot
BAG-401/7 10 mm slot
Weight : 3,25 kg each
www.besmaklab.com 83
AGGREGATE PARTICAL SIZE AND SHAPE
The High Capacity Sieve Shaker is used for gradation analysis of sample
batches up to a maximum of one cubic foot (0.028 m³). It will separate
the sample in up to seven sizes simultaneously in less than five minutes.
Designed primarily to separate materials with sizes in the range of 4 in (10,1
cm) to No. 4. It will also handle smaller amounts of finer materials down to No.
200. 45 x 65 x 7,5 cm sieves used. 30 kg capacity.
Sieves are hydraulically compressed. Sieves are optional. 220 V 50 Hz.
SPECIFICATIONS:
Product Code : BAG-414
BAG-414/2 Screen Tray Opening 3”
BAG-414/3 Screen Tray Opening 2 1/2”
BAG-414/4 Screen Tray Opening 2”
BAG-414/5 Screen Tray Opening 1 1/2”
BAG-414/6 Screen Tray Opening 1 1/4”
BAG-414/7 Screen Tray Opening 1”
BAG-414/8 Screen Tray Opening 3/4”
BAG-414/9 Screen Tray Opening 1/2”
BAG-414/10 Screen Tray Opening 3/8”
BAG-414/11 Screen Tray Opening 4.75 mm
BAG-414/12 Screen Tray Opening Cover
Weight : 210 kg
Dimensions (w x l x h) : 620 x 900 x 1200 mm
Sieve (45mm) Weight : 5 kg
RIFFLE BOX
EN 933-3 - ASTM C136 - AASHTO T27 - AASHTO T87 - BS 812 – BS 1377 – BS 1924
Electro-static dyed. Each riffle box comes with 2 collection
cups and 1 filling cup.
7-13-15-19-25-30-38-50-64 mm slot available.
SPECIFICATIONS:
Product Code : BGE-615 SET
BGE-615/1 7 mm
BGE-615/2 13 mm
BGE-615/3 15 mm
BGE-615/4 19 mm
BGE-615/5 25 mm
BGE-615/6 30 mm
BGE-615/7 38 mm
BGE-615/8 50 mm
BGE-615/9 64 mm
84 www.besmaklab.com
PARTICAL SIZE AND SHAPE AGGREGATE
LABORATORY CRUSHER
Features:
• Feeding capacity up to 100 mm
• Cutting size 3-10 mm
• Patented self-locking nut and full access to the
trench knife. Single easy installation with semi-
automatic folding legs.
• Slurry collection tray for long-term use of
the pump. A water pump can be chanced easily
with quick electrical connection.
A water pump is optional.
SPECIFICATIONS:
Product Code : BAG-415
Blade diameter : 400 mm / 15.8 inches
Max cutting depth : 230 mm / 9.1 inches
Max cutting length : 700 mm / 27.6 inches
Product size, : LxWxH 1120x600x600 mm / 44.5x24.8x26.8 inches
EN 933-4
Length Gauge, Flakiness Gauge and Shape Index Calliper
Flakiness and elongation index test set are used for the
determine of physical specification of aggregates.
SPECIFICATIONS:
Product Code : BAG-403
BAG-403/1 Length Gauge
BAG-403/2 Flakiness Gauge
BAG-403/3 Shape lndex Callipers
www.besmaklab.com 85
AGGREGATE MECHANICAL PROPERTIES
SPECIFICATIONS:
Product Code : BAG-407 Los Angeles Abrasion Machine
BAG-407/1 Cabinet
BAG-407/2 Abrasive Charges Set / EN
BAG-407/3 Abrasive Charges Set/ ASTM
BS 812-110
The aggregate crushing value provides a relative measure
of the resistance of an aggregate to crushing under a
gradually applied compressive load.
SPECIFICATIONS:
Product Code : BAG-411, 75 mm dia.
BAG-411, 150 mm dia.
86 www.besmaklab.com
MECHANICAL PROPERTIES AGGREGATE
EN 1037-1
Micro-Deval Test Machine
used to determine the
resistance of aggregates
by abrasion.
SPECIFICATIONS:
Product Code : BAG-408 Micro Deval
BAG-408/1 Abrasive Charges Set
BAG-408/2 Drum
BS 812-112
Used to determine the impact value of aggregates and select them for a given
application. The machine has a trip-action hammer release, blow counter device
and a built-in operator safety device.
Manufactured in heavy duty form with hardened steel surfaces for minimum
wear. The complete assembly is cadmium plated for corrosion protection.
Electrostatic dyed to against corrosion. Consist of counter, mould and tamping rod.
SPECIFICATIONS:
Product Code : BAG-410
Weight : 52 kg
Product Sizes (w x l x h) : 304 x 470 x 830 mm
www.besmaklab.com 87
AGGREGATE CHEMICAL TESTS
SPECIFICATIONS:
Product Code : BCE-319/1 Color Standard Chart
BCE-319/2 Graduated Bottle
BCE-319/3 Sodium Hydroxide
SPECIFICATIONS:
Product Code : BAG – 419 Magnesium / Sodium Sulphate Test
BAG – 419/1, Basket
BAG – 419/2, Stainless Steel Mesh
BAG – 419/3, Hydrometer
BAG – 419/4, Magnesium Sulphate
BAG – 419/5, Sodium Sulphate
EN 933-9
The methylene blue test set used to determine the clay content in the fine
portions of the aggregates.
The set comprises electric stirrer adjustable from 400 to 600 rpm, stirring
palette, 30 g methylen blue, 500 g kaolinit, 50 ml burette, burette stand, 2000
ml beaker, bagget and 50 filter papers. 220 V 50 Hz.
SPECIFICATIONS:
Product Code : BAG-406
Weight : 10 kg
88 www.besmaklab.com
DENSITY, VOID AND BULKING AGGREGATE
SPECIFICATIONS:
Product Code : BAG-420
Weight : 30 kg
Product Size (w x l x h) : 410 x 670 x 1000 mm
SPECIFICATIONS:
Product Code : BAG - 421
www.besmaklab.com 89
AGGREGATE DENSITY, VOID AND BULKING
BULK DENSITY
SPECIFICATIONS:
Product Code : BAG-412/1 1 lt. BAG-412/3 10 lt
BAG-412/2 3 lt BAG-412/4 15 lt
BAG-412/4 5 lt BAG-412/5 20 lt
BAG-412/5 7 lt BAG-412/6 30 lt
PARTICLE DENSITY AND WATER ABSORPTION (ABRAHAM CONE AND TAMPER) TEST SET
SPECIFICATIONS:
Product Code : BAG-413
Weight : 500 gr
90 www.besmaklab.com
DENSITY, VOID AND BULKING AGGREGATE
ASTM D 7382-08
SPECIFICATIONS:
Product Code : BAG – 422
• The ability to rapidly and accurately measure the moisture content of hundreds of tons of
material.
• There is no sampling, use of chemicals, balances or ovens.
• Used in any environment where minerals or building materials are being shipped, stored
or processed.
Product Code : BAG – 418/1 – Moisture Meter stack type - 1 metre length
BAG – 418/2 - Moisture Meter stack type - 2 metre length
www.besmaklab.com 91
AGGREGATE DENSITY, VOID AND BULKING
Cement
SAND EQUIVALENT
AIR CONTENT
TEST
METER
SET
SPECIFICATIONS:
Product Code : BAG-404/1 EN
BAG-404/2 ASTM
Weight : 7,5 kg
SPECIFICATIONS:
Product Code : BAG-404
Weight : 24 kg
Oscillating excursion
( at 175 strokes (±2 rounds) / minute rate ) : 200 mm (±10 mm)
92 www.besmaklab.com
ASPHALT
“
ASPHALT BITUMEN TEST EQUIPMENTS
SEMI-AUTOMATIC PENETROMETER
Digital measurement of the penetration values.
The penetrometer comprises:
• baseplate with spirit level,
• vertical mounting rod with height-adjustable penetration arm,
• integrated displacement transducer to measure the penetration,
• electronic plunger release.
Machine functions:
Electronic plunger release Specifications:
By pressing the start button of the control unit, the plunger is
released. After the time preset at the quarz timer has elapsed • Measuring range: 0-350 penetration units (equivalent
(works setting 5.0 sec), the plunger is electromagneticaliy to 0-35mm)
clamped.
• Resolution: 0.04 mm
Height adjustment
By rotating the handwheel, the height of the penetration • Test load: 100g for needle penetration, 150g for conic
arm can be set. penetration
SPECIFICATIONS:
Product Code : BAS-513/2
Weight : 24 kg
Dimensions : 250 x 380 x 574 mm
Power : 220V, 50Hz
DIGITAL PENETROMETER
The standard penetrometer is ruggedly constructed, with an aluminium base table with
levelling screws, plated vertical rod, “micrometric vertical adjustment device”. The slider
is brass made with free fall.
It has a magnetic controller device with electronic digital programmable timer that
automatically releases the plunger head and ensures free falling of the needle during
the 5-seconds test.
Unit has indicator dial, plunger, containers and needles.
SPECIFICATIONS:
Product Code : BAS-513/1
Weight : 7 kg
96 www.besmaklab.com
BITUMEN TEST EQUIPMENTS ASPHALT
SPECIFICATIONS:
Product Code : BAS-515/2
Heater : 0, 8 KW
Weight : 22 kg
Dimensions : 320x400x455
Power Supply : 220 – 240V 1ph 50/60Hz
SPECIFICATIONS:
Product Code : BAS-515/1
Weight : 12 kg
Dimensions : 320x400x455
Power Supply : 220 – 240V 50/60Hz
www.besmaklab.com 97
ASPHALT BITUMEN TEST EQUIPMENTS
SPECIFICATIONS:
Product Code : BAS-514
Weight : 9 kg
Dimensions : 140x240x130
DUCTILITY MACHINE
SPECIFICATIONS:
Product Code : BAS-518/1.
Weight : 113 kg
Dimensions : 1960mm.x350mm.x8600mm.
Power : 220-240V 50Hz
98 www.besmaklab.com
BITUMEN TEST EQUIPMENTS ASPHALT
SPECIFICATIONS:
Product Code : BAS-517
Weight : 20 kg
Dimension : 460x600x300
Power : 220V 50 Hz
ASTM D6307
The Asphalt Content/Binder Furnace with internal automatic
balance is an environmentally-friendly and cost-effective method
for the accurate determination of asphalt content. Furnace’s large
capacity handles samples up to 4,000 grams.
Ignition method reduces testing time compared to solvent testing
methods and automatic operation frees technicians for other tasks.
Temperature range is: 200 to 650°C. Accurate internal balance
monitors weights automatically throughout ignition to within ±0.1
gram.
Easy operation simply enter sample weight, calibration factor, load
the sample, and push start, when unit beeps at test end, push stop,
and sign receipt.
Door safety features, such as a software-activated door lock,
an automatic interlock that cuts power when door is open, full
180 degree door opening and door hinge lock eliminate harmful
solvents and make operation easy. CE-Approved.
SPECIFICATIONS:
Product Code : BAS-519
Weight : 27 kg
Power : 220V 50 Hz
www.besmaklab.com 99
ASPHALT BITUMEN TEST EQUIPMENTS
CENTRIFUGE EXTRACTOR
SPECIFICATIONS:
Product Code : BAS-502/1 3000 gr BAS-502/2 1500 gr
Weight : 55 kg 50 kg
Dimensions : 600 x 190 x 670 mm 550 x 175 x 720 mm
Accesories : Filter Paper 100 pcs/1 packet Filter Paper 100 pcs/1 packet
Power : 220V, 50 Hz 220V, 50 Hz
SPECIFICATIONS:
Product Code : BAS-501/1 4000 gr BAS-501/2 1000 gr
Weight : 7 kg 5 kg
Accesories : Filter Paper 50 pcs/1 packet Filter Paper 50 pcs/1 packet
100 www.besmaklab.com
BITUMEN TEST EQUIPMENTS ASPHALT
FILM OVENS
SPECIFICATIONS:
Product Code : BAS - 516
Weight : 96 kg
Dimensions : 730 x 750 x 630 mm
Power : 220 V 50 Hz.
SPECIFICATIONS:
Product Code : BAS-516
Weight : 93 kg
Dimensions : 750 x 570 x 68 cm
Power : 220 V 50 Hz.
www.besmaklab.com 101
ASPHALT PAVEMENT TEST EQUIPMENTS
SPECIFICATIONS:
Product Code : BAS-504
Weight : 185 kg
Dimensions : 1880 x 535 x 535 mm
Power : 220 V 50 Hz
SPECIFICATIONS:
Product Code : BAS- 506
Weight : 4,5 kg
SAMPLE EXTRUDER
SPECIFICATIONS:
Product Code : BAS-507
Weight: 25 kg
Dimensions: 70x55x110 mm
102 www.besmaklab.com
PAVEMENT TEST EQUIPMENTS ASPHALT
SPECIFICATIONS:
Product Code : BAS-508
Weight : 70 kg
Dimensions : 450 x 605 x 960 mm
Power : 220V 50 Hz
SPECIFICATIONS:
Product Code : BAS-508
Weight : 70 kg
Dimensions : 450 x 605 x 960 mm
Power : 220V 50 Hz
SPECIFICATIONS:
Product Code : BSO-208-3
Weight : 70 kg
Dimension : 400 x 605 x 960 mm
Power : 220 V 50 Hz.
www.besmaklab.com 103
ASPHALT PAVEMENT TEST EQUIPMENTS
ASTM D1559
Water Bath with microprocessor-based temperature control for precise temperature control throughout the range.
Available capacities as 30 – 48 – 60 Litres
Digital PID controller,
Circulation feature,
Cooling unit is optional.
SPECIFICATIONS:
Product Code : BGE-613
Weight : 50 kg
Power : 220V, 50Hz
ASPHALT MIXER
EN 12697-35 - BS 598:107
This bench mounting Mixer is utilized for mixing samples of
bituminous materials. it ensures uniform mixing.
5 lt capacity,
Heater is optional.
SPECIFICATIONS:
Product Code : BAS-509/1 , BAS-509/2 with Heater
Weight : 85 kg
Dimensions : 650x600x380
Power : 220 V 50 Hz
104 www.besmaklab.com
ASPHALT QUALITY CONTROL EQUIPMENTS ASPHALT
GYRATORY COMPACTOR
SPECIFICATIONS:
Product Code : BAS-505
Weight : 250 kg
Dimension :
EN 12272-3
Used to evaluate the global adhesion and the active adhesion
between bitumen and aggregates for road surfaces realization.
Consist of Six metal test plates., steel ball, metallic hand operated
roller, metallic base, aggregate spreader apparatus.
SPECIFICATIONS:
Product Code : BAS-520
Weight : 40 kg
Dimension :
Power : 220V 50 Hz
www.besmaklab.com 105
ASPHALT ASPHALT QUALITY CONTROL EQUIPMENTS
Used to measure planeness of pavement surfaces, such as highways, airport runways, bridge
decks, etc. Requires only one operator to detect, register, and dye mark high and low areas that
need to be ground down or filled.
A marker system is supplied with the equipment.
One-person can easily operate.
SPECIFICATIONS:
Product Code : BAS-512
Overall Length : 3.2 m
Weight : 60 kg
Dimensions : 780x320x500
SPECIFICATIONS:
Product Code : BAS-512/1
Weight : 18 kg
SPECIFICATIONS:
Product Code : BAS - 522
Weight : 32Kg.
Dimension : 730x730x330 mm
106 www.besmaklab.com
ASPHALT QUALITY CONTROL EQUIPMENTS ASPHALT
The EZ gauge features a menu-driven control panel with easy-to-use, built-in test routines and auto features, making testing
a quick and accurate operation. It also features our innovative trigger release handle that eliminates pinched fingers while
providing smooth operation. Available in 8” (200mm) and 12” (300mm) lengths with either 1” (25mm) or 2” (50mm) increments,
the EZ gauge provides a single gauge solution to density and moisture measurements. The EZ’s versatility allows it to measure
density through direct transmission and backscatter modes, as well as including thin lift and trench modes, as well as moisture
determinations. The gauge uses an advanced micro-processor-based technology to provide highly-accurate measurements of
density and moisture that are automatically computed for direct readouts of wet density, dry density, moisture content, percent
of moisture, percent of compaction (Proctor or Marshall), void ratio and air voids. The EZ Gauge complies with all pertinent
standards: ASTM D6938, D2950, C1040 and AASHTO T310. The gauge is calibrated by the Five-block calibration method.
• Menu driven
SPECIFICATIONS:
Product Code : BSO-218
Weight : 41kg
Dimensions : 660x585x355
Power : 220 V 50 Hz.
www.besmaklab.com 107
ASPHALT AUXILARY EQUIPMENTS
SPECIFICATIONS:
Product Code : BAS-511
Motor Power : 6,5Hp
Weight : 85 kg
Dimensions : 435 x 800 x 1050 mm
EN 12272-3
This complete stand-alone core drill rig offers field independence, versatility, dependability and easy single person operation.
Can be carried in pick-up or van for easy transport. Features include; Fuel core drill machine, water tank, steel construction trailer
with 2 wheels. Bits are optional (50 mm, 75 mm, 100 mm, 150 mm)
SPECIFICATIONS:
Product Code : BAS-520
Weight : 340 kg
Dimensions : 1360 x 2554 x 1793 mm
108 www.besmaklab.com
MATERIAL
TESTING
112 www.besmaklab.com
SERVOHYDRAULIC UNIVERSAL MATERIAL TESTING
Application:
BMT-S Series machine is designed with single workspace for testing various materials. It can do the tension, compression,
bending and shearing tests. Force measurement is through load cell. With long travel actuator stroke, it is suitable to test
standard specimen, long length specimen and specimen with large elongation.
Controller unit is by DOLI (Made in Germany)
Servo-Valve is by MOOG (Made in USA)
Machine Class: 0.5
Applied Standards:
Load meets or exceeds the following standards: ASTM E4, ISO7500-1, EN 10002-2, BS1610 and DIN 51221.
Strain measurement meets or exceeds the following standards: ASTM E83, ISO 9513, BS 3846 and EN 10002-4.
Compatible to the standards ASTM A370, ASTM A615 and EN 10002.
Controller Features:
BESMAK BMT-S Series Testing Machines are controlled by DOLI EDC DOLI EDC 220 Fits For;
220 controller unit and RMC-7 handheld unit.
a) The EDC220 has a load channel with a resolution
of ±180,000 steps and an incremental position
channel with a controlled ±10Volt output for power
amplifiers.
• Data Acquisition and Control System DOLI – EDC 220:
EDC controller is imported from Germany and widely used for testing b) Further load cells, LVDTs, strain gauges,
machine with high configuration or requirements. EDC220 is a built- extensometers, 2-channel-incremental-
in unit without keys and display and has been designed for static extensometers, serial controlled extensometers,
and dynamic testing instruments. It features as stable control, high safety shields, further I/Os, synchronizing several
accurate measuring and high sampling rate (1 kHz~5 kHz) etc. Also, EDCs in a multi-channel application.
it can self-identify & self-calibration functions. Up to now, it is most
reliable device to be used extensively for static and dynamic testing c) Digital control; Closed Loop Control
machines.
d) Connection with RS 232 and Ethernet
All measuring channels for a basic testing instrument, as well as an
output channel to control an actuator, are on- board. The EDC220V
e) Interface to PC, printer
has two I2-Bus-Extension-Slots for e.g. extensometers. The on-
board load channel of the EDC220V has a resolution of ±180,000
steps. f) Display of outputs (stand-alone)
j) Testanalysis (stand-alone)
k) Data-logging (stand-alone)
www.besmaklab.com 113
MATERIAL TESTING SERVOHYDRAULIC UNIVERSAL
RMC-7 is a handheld unit (cable 3m) connected directly to the EDC. The RMC-7 has a magnetic foil on its back and therefore can
be placed at an ergonomic position.
RMC-7 handheld unit has an emergency stop button onto it (the red button at the right top). In case of an emergency situation,
process can be easily stopped.
RMC-7 handheld unit provides to control and monitor Test Speed Adjustment, Grips Position Control, Active Crosshead Control
(up-down movement speed), Load/Deformation, Extension, Real-Time % Extension. Automatically stops when the piston
reaches to maximum displacement point etc.
114 www.besmaklab.com
SERVOHYDRAULIC UNIVERSAL MATERIAL TESTING
• 32Bit-Program
• Simple and intuitive operation
• Customized and field-proven applications
• All protocols and printouts freely definable
• “Free Programming Module” for individual tests
• Compatible to each EDC system from DOLI
• Export into ASCII or EXCEL files
• Almost all applications possible in the testing lab
• Use as production testing system in online mode, also
integrated graphics
• Integration of several additional channels possible
• Direct connection of thickness gauges, calipers and other measurement instruments via RS232
• Fast and reasonable testing
• Connection types are Ethernet and RS-232
Extensometers:
www.besmaklab.com 115
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
Applications:
BMT-E Series DOLI Controlled Electro-Mechanical Universal Testing Machine is designed and manufactured according to ASTM,
ISO, DIN, EN etc. standards. It is Doli controlled precision testing machine, suitable for extensive metallic & nonmetallic materials
for tension, compression, bending, shearing and cycle test etc. It features as high precision, high stability as well as high
reliability. Complete with modulus for metal, spring, textile, rubber, plastic and other material testing. It is widely used in many
fields of R&D, QC and QA and education institutes.
116 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
Features:
The design purpose of this load frame with double/four columns is to ensure safety, reduce operator fatigue and provide the
highest level of flexibility. Concretely, it features as following:
• High accuracy: the preloaded precision ball-screw eliminates the backlash & ensures position measurement accuracy. A
built-in scale on the frame indicated the crosshead position for verification of normal strain testing.
• Safety features: equipped with the upper and lower limit switches, testing machine can stop automatically when applied
test force exceeds the specified value during operations.
• Large space in the working area: the distance between columns provides wide space for the operator.
• Over-stroke limiter: the range of the crosshead movement mechanically limited.
• Comfortable working area: the wide legroom under the load unit provides a comfortable working area for attaching and
removing jigs.
www.besmaklab.com 117
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
Specifications:
118 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
Climate Chamber and Video Extensometer Integrated Electro-Mechanical UTM with PC Software
www.besmaklab.com 119
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
Application:
This testing machine is designed for tensile mechanical property test on metallic or nonmetallic materials as per ASTM, ISO,
DIN, GB standards. A variety of fixtures can be offered to do compression, bending and shearing test as well. It is suited for
the applications in quality inspection, research, metallurgy, rubber & plastics, and knitting materials, and widely used in many
fields such as industry factories, mineral enterprise and high schools.
120 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
Extensometers:
Extensometers including non-contact video & laser extensometer and contact type & full automatic extensometers
are available to meet different kinds of test requirements. Please see the following different types.
www.besmaklab.com 121
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
APPLICATIONS:
The furnace & climatic chamber are especially used for universal testing machine according to the required temperature to
equip with corresponding load frames for various metallic or nonmetallic materials. This unit consists of furnace/chamber body,
controller, high temperature grips, pull rod and bracket.
The temperature can be controlled automatically by PID controller with high accuracy. Also it can make data communications
with the computer. The temperature range & furnace/chamber size can be defined according to the customer’s requirements. It
is the ideal material test equipment used for universities, research institutes and enterprises.
EDC controller is imported from Germany and widely used for testing
machine with high configuration or requirements. EDC220 and 580
is a built-in unit without keys and display and has been designed for
static and dynamic testing instruments. It features as stable control,
high accurate measuring and high sampling rate (1 kHz~5 kHz) etc. Also,
it can self-identify & self-calibration functions. Up to now, it is most
reliable device to be used extensively for static and dynamic testing
machines.
a) The EDC220 has a load channel with a resolution of ±180,000 steps and an incremental position channel with a
controlled ±10Volt output for power amplifiers.
b) Further load cells, LVDTs, strain gauges, extensometers, 2-channel-incremental-extensometers, serial controlled
extensometers, safety shields, further I/Os, synchronizing several EDCs in a multi-channel application.
c) Digital control; Closed Loop Control
d) Connection with RS 232 and Ethernet
e) Interface to PC, printer
f) Display of outputs (stand-alone)
g) Detection of load, position, strain etc.
h) Test control (stand-alone)
i) Data acquisition (stand-alone)
j) Testanalysis (stand-alone)
k) Data-logging (stand-alone)
122 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
RMC-7 is a handheld unit (cable 3m) connected directly to the EDC. The RMC-7 has a magnetic foil on its back and therefore can
be placed at an ergonomic position.
RMC-7 handheld unit has an emergency stop button onto it (the red button at the right top). In case of an emergency situation,
process can be easily stopped.
RMC-7 handheld unit provides to control and monitor Test Speed Adjustment, Grips Position Control, Active Crosshead Control
(up-down movement speed), Load/Deformation, Extension, Real-Time % Extension. Automatically stops when the piston
reaches to maximum displacement point etc.
• 32Bit-Program
• Simple and intuitive operation
• Customized and field-proven applications
• All protocols and printouts freely definable
• “Free Programming Module” for individual tests
• Compatible to each EDC system from DOLI
• Export into ASCII or EXCEL files
• Almost all applications possible in the testing lab
• Use as production testing system in online mode, also
• Integrated graphics
• Integration of several additional channels possible
• Direct connection of thickness gauges, calipers and other measurement instruments via RS232
• Fast and reasonable testing
• Connection types are Ethernet and RS-232
www.besmaklab.com 123
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
VIDEOEXTENSOMETER
To measure simultaneously the longitudinal and the transversal strain a backlight (Pos. 8c) is required. It is possible to install
the RTSS system on the control computer for the tensile test machine.
CAMERA RTSS_HR
Compact quality lens Schneider-Kreuznach. Standard focal lengths: 8, 12, 35, 50, 80 mm.
The optimal lense is selected depending on the application. (Other lenses on request).
124 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
Desktop PC Dell, Optiplex MT, Intel I3 (Dual Core CPU) with 3.3GHz, 4GB RAM, 500GB HD, 16x DVD+/-RW, Windows 7, 19” LCD
Monitor, 3 years next-business-day-on-site-repair.
The Real Time Strain Sensor (RTSS) Software is a contact less strain analysis software based on a single camera
and real time image processing for use on e.g. tensile test machines. The strain is measured typically between two
lines or markers and the contour outlines.
Typical applications are determination of material properties [Young’s modulus, poisson ration] , strain controlled tensile
tests, exploration of cracks, investigation of strain behaviour on cyclical tensile tests, dynamic and highspeed tests,
vibration analysis, etc.
The data is transferred via digital or analogue interface to external devices and software. signal for controlling of
external software and devices. RTSS is 100% compatible to universal tensile test machines of Instron, MTS, Zwick,
Schenk, etc.
FEATURES:
Multi marker tracking: For a spatial resolved strain measurement up to 20 line markers can be measured simultaneo-
usly.
www.besmaklab.com 125
MATERIAL TESTING ELECTROMECHANIC UNIVERSAL
Single images (TIF, BMP, JPG) can be saved during the test. The
images can be converted to AVI movies and the strain disctribution can be analyzed afterwards with digit image cor-
relation.
• DOLI-Controller-compatible (option)
MULTI CAMERA MODULE: Multiple cameras can be connected to one computer and be used in following modes:
Dependent mode:
• Combination of the precise Youngs modul measurement (small FOW camera) and the complete measurement
of the stress-strain curve (with large FOW camera).
CALIBRATION PLATE
Calibration plate for the accurate calibration of the system (measures in mm).
FOW calibration: 10 to 100mm (other sizes on request).
126 www.besmaklab.com
ELECTROMECHANIC UNIVERSAL MATERIAL TESTING
MARKER SET
With the module DAQhw the measurement values can be transferred as analogue voltage signals to the tensile test
machine. Up to 2 analogue signals (±10V, 16bit) can be transferred simultaneously.
DAQhw allows also to acquire analogue signals (4 channels, ±10V, 16bit) that can be used via an ASCII log file e.g.
in the 2D-DIC software for postprocessing.
TRIPOD
3D HEAD
3D geared head for the easy camera mounting and accurate and flexible adjustment of orientation.
Front illumination (cold light) fort he usage with temperature chambers. (Mounting from outside).
LED BACKLIGHT
LED-light array (cold light) for transversal strain measurement. Size: 300x100mm.
SUPPORT
www.besmaklab.com 127
MATERIAL TESTING CREEP TESTS
APPLICATIONS:
BMT-C Creep Material Testing Machine is a kind of full electronic creep testing machine
(also mechanical is available) to perform routine creep and stress-rupture test, and also can
carry on stress relaxation test, high-temperature tensile test in short time, cycle load test
(load spectrum test), low cycling test etc.
SPECIFICATIONS:
• Max. load: 30kN, 50kN, 100kN, 200kN
• Effective measuring range: 1% 100%FS;
• Test load accuracy: ≤1%;
• Resolution: 1/200000
DEFORMATION MEASUREMENT:
128 www.besmaklab.com
CREEP TESTS MATERIAL TESTING
APPLICATIONS:
SPECIFICATIONS:
Product Code: BMT-804
www.besmaklab.com 129
MATERIAL TESTING IMPACT TESTS
APPLICATIONS:
BMT-450P/ 750P Series Pendulum Impact Material Testing Machines are strictly designed according to international standard
ISO148-1983, ASTM E23 and EN10045. It is mainly used to determine the anti-impact capability of metal materials under
dynamic load. It is especially suitable for laboratory, metallurgy industry, machinery production, steel plant and other fields.
FEATURES:
5.4
Raised angle (º) 150
Standard span (mm) 40
Round angle of jaws (mm) R1-1.5
Round angle of striking edge (mm) R2-2.5
Size of specimen (mm) 10 x 10 x 55
Power supply 3phs, 380V, 50Hz
Dimensions (mm) 2144 x 736 x 1390 2450 x 1200 x 2455
Net weight (kg) 650 900
130 www.besmaklab.com
IMPACT TESTS MATERIAL TESTING
APPLICATIONS:
BMT-DW Series Drop Weight Impact Material Testing Machine is suitable for drop weight tear test of various kinds of ferrites,
especially for the test of pipeline steel as ASTM-E 436, ASTM-E 208 and DIN EN 10274. Comes with various weights and anvils.
APPLICATIONS:
Impact energy is adjusted by the lifting height and the numbers of the weights.
The buffer is equipped to absorb the residual energy after breaking the specimen to protect the weight and anvil from destroy-
ing. Also install the safe outfit, such as safety net, safe pin for maintenance and hanger locking.
Equipped with the specimen-carrying outfit, anti-falling of outfit for the specimen, centering outfit to guarantee quick, accurate
and reliable tests.
www.besmaklab.com 131
MATERIAL TESTING TORSION TEST
APPLICATIONS:
BESMAK BMT-T Series Torsion Material Testing Machine is mainly used to test the plasticity of metal wires and ropes under
torsion condition. Surface flaws of steel wires may be shown out during the testing process. It is most suitable for quality
inspection of departments related to steel wire. The revolution is displayed on a 4-digit LED. The revolution value is automatically
held at the break of specimens.
Standards: ASTM A938, ISO7800.
SPECIFICATIONS:
132 www.besmaklab.com
GENERAL
EQUIPMENTS
OVENS
Can be set between room temperature and 250 ˚C. 0.1 ˚C reading precision.
Different capacity models are available; 50, 120, 250, 500, 750 and 1000 l inner
cabinet temperature precision depends on capacity . Precision on 750 l is 2.7 ˚C.
Stainless steel inside, electrostatic dyed outside. Digital adjustment and display
panel. 220 V 50 Hz.
SPECIFICATIONS:
BGE-612
MUFFLE FURNACES
Optimized isolation and unique design are main factors for minumum heat loss
and to keep outer surface temperature of main body & amp; front door minumum.
Low temperature at the surface makes possible locate the control unit at the top
of main body. It makes users control the menu easily.
Heating resistance is designed very carefully. It is main item deetrmining furnace
heating speed and working life.
Heating resistance is protected by quartz tubes against gases which come out in
the chamber during heating process.
Fan system lets the weairng/ abressive gases come out the furnace through the
chimney.
5,7 and 10 l capacities and open or closed resistance models are available.
2 memory to keep 2 different program to
PID CONTROLLED SOFTWARE AND CONTROL UNIT be able to choose and use easily,
4 line wide display and user friendly menu, Sound warnings when the steps change
PID Controlled unit, and the whole heating program is ended,
Precise temperature control (+/- 1°C), Timer indicates total heating time,
Heating accelaration option between 5°C/min. - 25°C/min. , Sound warning and automatic heating cut
off system, if the control unit/control card
Direct or 2 stepped heating program, is overheated to get rid of any overheating
danger,
Sound warning and automatic heating cut
SPECIFICATIONS: of, if the furnace is heated over maximum
BGE-603 heating temperature due to any reason,
BGE-603/1, 1100 C Temperature calibtaion correction via
BGE-603/2, 1200 C Menu,
Digital PID Controller. 229-380 V 50 Hz.
136 www.besmaklab.com
GENERAL EQUIPMENTS
HOT PLATE
SPECIFICATIONS:
BGE-602
WATER BATHS
30, 45, 60 and 90 l capacity models are available, can be set between room
temperature and 90 ˚C, stainless steel container. Cooling unit 90˚C is optional.
220 V 50 Hz.
SPECIFICATIONS:
BGE-613
0.0001, 0.001, 0.01, 0.1, 1, 2, 5, 10, 20, 50 and 100 g precision models
are available . External and internal calibration models are available .
Some models fitted with battery for in-situ, some models are suitable for
bouyancy balance application.
SPECIFICATIONS:
BGE-614
www.besmaklab.com 137
GENERAL EQUIPMENTS
COMPRESSORS
25, 50, 100, 150, 200, 250, 500, 1000 l capacity,8, 10 and 14 bars types
are available .
SPECIFICATIONS:
BGE-617
VACUUM PUMPS
SPECIFICATIONS:
BGE-616 Vacuum Pump
BGE-616/1, 1.8 m³ single stage
BGE-616/2, 3 m³ single stage
BGE-616/3, 5 m³ single stage
BGE-616/4, 8 m³ single stage
BGE-616/5, 1.5 m³ double stage
BGE-616/6, 3.2 m³ double stage
BGE-616/7, 5 m³ double stage
PH METER
SPECIFICATIONS:
BGE-618
138 www.besmaklab.com
GENERAL EQUIPMENTS
SPECIFICATIONS:
BGE – 624/1, Measures
BGE – 625/2, Beakers
BGE 646/1, Funnels
BGE – 626 Volumetric Flasks
BGE – 634 Conical Flasks
BGE – 627 Pycnometers
BGE – 629 Desicators
BGE – 630 Desicators Vaccum Type
SPECIFICATIONS:
BGE-623 Trays
BGE-623/1 Rectangle Tray inner dimensions: 23 x 35 x 4 cm
BGE-623/2 Rectangle Tray inner dimensions: 25 x 40 x 4 cm
BGE-623/3 Rectangle Tray inner dimensions: 27 x 44 x 5 cm
BGE-623/4 Round Tray 40 cm diameter, 5 cm depth
BGE-648/5 Mixing Bowls
BGE-648/501, 1,4 l
BGE-648/502, 2,8 l
BGE-648/503, 5,2 l
BGE-648/504, 7,6 l
BGE-648/505, 13,9 l
www.besmaklab.com 139
GENERAL EQUIPMENTS
METAL EQUIPMENTS
SPECIFICATIONS:
BGE - 604, Trovels
BGE – 621, Shovels
BGE - 639, Flexible Spatulas
BGE - 664, Scoops
PLASTIC EQUIPMENTS
SPECIFICATIONS:
BGE - 624/2, Measures
BGE - 625/1, Beakers
BGE – 626, Volumetric Flasks
BGE – 634, Conical Flasks
BGE – 637, Buckets
BGE – 638, Wash Bottles
BGE - 646/2, Funnels
BGE – 671, Bottles
PORCELAIN EQUIPMENTS
SPECIFICATIONS:
BGE – 631, Mixing Crucibles
BGE – 632, Mortar and Pestles
BGE – 633, Burn Crucibles
140 www.besmaklab.com
GENERAL EQUIPMENTS
The device can to keep a constant temperature, make heating and cooling
process at the desired speeds and make water intake or water discharg-
ing process. There are also drain valve.
The device stops when the end of the number of cycles. If when the end
of the cycles is required to remain at the desired temperature, it should
be added before program starting.
Thawing in water; water intake, the waiting time in the water and water
discharging can be defined as a parameter each with a different.
Cabin is equipped with a flap top and piston driving. Water intake tank is
independent. The water level in the cabin can be seen on the device com-
puter screen. Can be connected to a computer. Comes with the software
program.
Complies with CE standards.
SPECIFICATIONS:
WATER DISTILLATION
4 I/h capacity, can be fixed to wall or can be used table top. Dimensions
are approximately 250x222x542 mm. Weight is approximately 13 kg. 220
V 50 Hz.
SPECIFICATIONS:
BGE-608
www.besmaklab.com 141
GENERAL EQUIPMENTS
SPECIFICATIONS:
BGE-647/4 Moisture Container
BGE-647/401, 50mm diameter, 50 mm height.
BGE-647/402, 55mm diameter, 40mm height
BGE-647/403, 60mm diameter, 65mm height
BGE-647/404, 75mm diameter, 30mm height
BGE-647/405, 78mm diameter, 50mm height
BGE-647/406, 88mm diameter, 50mm height
BGE-647/407, 97mm diameter, 50mm height
BGE-647/408, 97mm diameter, 100mm height
BGE-647/409, 128mm diameter, 67mm height
Digital , analog , mercury , alcohol models and pocket or hand types are available.
-50.. +150, 200 , 250, 300 ˚C digital,
-10.. +50 , 100 , 150 , 300 ˚C mercury and alcohol,
-50.. +50 , 100 , 250 ˚C analog.
Thermohygrometer.
Stopwatch.
SPECIFICATIONS:
BGE – 643/ 1 Mercury and Alcohol Thermometer
BGE- 643/3 Digital Thermometer
BGE – 643/ 4 Analog Thermometer
BGE-644 Thermohygrometer
BGE-606 Stopwatch
142 www.besmaklab.com
GENERAL EQUIPMENTS
CALIPERS
SPECIFICATIONS:
BGE-652 Calipers
BGE-652/1 Mechanical Calipers
BGE-652/2 Digital Calipers
BGE-652/8 Double-Jaw Digital Calipers
BRUSHES
SPECIFICATIONS:
BGE – 649/1 Plastic Brush
BGE – 649/2 Metal Brush
BGE – 649/ 4 Bristle Brush
www.besmaklab.com 143
GENERAL EQUIPMENTS
LOAD CELLS
Load cell, suitable for use in both compression and tension direction. High resistance
to off-axis load and overload.
1,2,5,10,20,30,50,100 ton capacities are available.
SPECIFICATIONS:
BGE- 654 Load Cells
144 www.besmaklab.com
GENERAL EQUIPMENTS
DIAL INDICATORS
SPECIFICATIONS:
BGE-651 Dial Gauge
BGE-651/1, 0 - 12 mm measuring range, 0.01 mm accuracy
BGE-651/2, 0 - 25 mm measuring range, 0.002 mm accuracy
THICKNESS GAUGE
SPECIFICATIONS:
BGE-667/8 range from 0.001-0.10 mm, increase 0.01 mm , 13 parts
BGE-667/9 range from 0.05-0.10 mm, increase 0.05 mm, 20 parts
MEMBRANES
Membranes are different sizes for 38 mm, 42 mm, 54 mm, 1.5 in dia samples.
SPECIFICATIONS:
BRC-707/5, 38 mm dia
BRC-707/5, 42 mm dia
BRC-707/5, 54 mm dia
BRC-707/5, 1.5 in dia
www.besmaklab.com 145
GENERAL EQUIPMENTS
GLOVES
ASBESTOS GLOVES
The following Load Rings are available with works calibration certificates.
SPECIFICATIONS:
BGE – 665/1
RUBBER GLOVES
For use in compaction, concrete and general lab work, medium thickness short-form
gloves without gauntlets are chemical and abrasion resistant and feature curved
fingers and contoured palm for ease while working.
SPECIFICATIONS:
BGE – 665/2
SPECIFICATIONS:
BGE – 665/3
SPECIFICATIONS:
BGE-667/6, DIN 875/1. Lenght 400 mm, Width 200 mm, Wall thickness
7,5 mm. Capped.
BGE-667/7, DIN 875/2 Lenght 300 mm, Width 175 mm, Wall thickness 7
mm. Capped.
146 www.besmaklab.com
INDEX
BAG - 421 Specific Gravity and Water Absorbtion For Fine Aggregate 89
www.besmaklab.com 147
INDEX
BAS-513 Penetrometers 96
148 www.besmaklab.com
INDEX
www.besmaklab.com 149
INDEX
BCO-122 Compressometer/Extensometer 15
150 www.besmaklab.com
INDEX
BGE-657 Sieves 82
www.besmaklab.com 151
INDEX
152 www.besmaklab.com
Istanbul Road 27. Km Saray District Aksoy Street No:53 Kazan / Ankara / TURKEY
Tel : +90 (312) 815 56 20 • Fax : +90 (312) 815 56 25 • info@besmaklab.com
www.besmaklab.com
www. kosgeb.gov.tr
BasımTarihi: 31.12.2012
Basım Yeri : Grafizm Reklam