Technical sp
Two A4 Colour LaserJet
supplied and networked, Cortsumables like
Purchaser.
2.2.8.4 LAN Stackable Switeh
ification No, THSPCIRCCSCADA. 130 (Re¥.2) fo SCADA sysom fe 25 KV
Sle Phase See Trton Power Sup
printers with Ix 10/]00Mbps Ethemet interface shall be
, cartridges shall be provided by
Two LAN stackable switches with up-link support, with 24-Ports, 100 Mbps and RJ4S
hall be provided,
Switches shall be of D-link, Cisco & Allied Telesis make or
a brand as specified by the purchaser in the tender.
2.2.8.5 Ceiling- mount Projector
A ceiling-mount projector with full-HD resolution and remote controlled wall-hanging
screen shall be provided. This projector shall be connected to second PC of the operator
workstation in parallel to its VDU.
The projector shall be capable for wireless connection with second PC of the
operator workstation as well and nee
wireless display of VDU on the projector screen through projector
of successful vendor.
ary hardwire/driver required for making the
shall be in the scope
When required the display of the operator workstation shall be projected onto the
sereen so that « multiple viewers can view/anal
Typically, the traction network overview shall be projected onto the ser
se the displayed information,
DETAILED SPECIFICATIONS OF PROJECTOR
Type DLP
Resolution 1920x1080 (1080p)
Lens (Zoom Ratio)
>Ix Manual optical zoom / Manual optical focus
Keystone
Vertical digital keystone correction: +/- 20 degrees
Display Size
30"-300" / 0.76m-7.6m
Throw Distance
Im-10m / 3.28ft-32.8ft
Lamp Type
230 watt
Lamp Life (normal/eco-mode)
2000/4000. hours
Brightness
2000 ANSI Lumens or above
Contrast Ratio
4000:1 (dynamic)
Aspect Ratio
16:9 (native), 4:3, 16:10, Auto
Input Signal
NTSC M (3.58 MHz), 4.43MHz, PAL (B, D, G, H,
1, M,N, 60), SECAM (B, D, G, K, K1, L), SD 480i
and 576i, ED 480p and 576p, HD 720p, 1080i and
1080p
Mounting Arrangement
Ceiling Mount
Accessories
Power cable, VGA cable, HDMI cable, remote
controlilaser with batteries, lens cap, remote
controlled wall mount screenTechical specifiation Ne, TESPCARCCISCADA’ 0134 (Rev) for SCADA syston
Phase S017 se Frsetion Power Sop
Input terminal (not Wi-Fi in] Wireless LAN (USB port) for IEE 80211 big/n for
built projector for wire
connection) display of VDU at
ss | wireless connection with projector for streaming
workstation
2.3. Details of UPS
The manufacturer shall provide a reliable on line UPS system of 2x5 KVA rating along,
with the batteries and associated equipment. The details of 2x5 kVA UPS system shall be
as under.
Item Description
Rating Each UPS shall be continuously rated for $ KVA at 0.8 PF, Input:3-Phase
415 "10% &-15% Vac, 50 43% Hz, Output: Stabilized 240Vac, 50 Hz
Arrangement | One UPS of 5 KVA rating shall be sufficient to eater for the entire load of
q RCC (maximum 3 kVA at 0.8 PF),
The UPS system shall operate in dual redundant hot standby mode where
another 5 kVA UPS shall provide 100% redundancy to the system.
‘The malfunction of online UPS shall cause it to automatically isolate trom
the system and the other UPS shall take up the load without an:
interruption,
Each UPS shall be designed to operate as a true on-line, double conversion
system where the UPS output is independent of input supply voltage &
fiequeney variations
Both the UPS unit shall share/connected to a single battery set. The voltage
of cach cell shall be 2 V and the bus voltage of Battery Bank shall be 488
TOV or higher suitable to UPS.
The UPS shall have Cold start facility
Battery Battery set of low maintenance lead acid batteries of sufficient AH capacity
to cater the fall RCC toad for minimum 3 hours shall be provided. The
batteries shall be suitable for UPS applications. (110V or higher battery
system so that the UPS and batteries could be used Interchangeably). The
ampere-hour rating to be decided based on the voltage & minimum 3 hrs.
backup time & fo be mentioned in the design drawings,
Output 2¥% total harmonic distortion (THD) for 100% linear
yalees | Load and + 4% for 100% nonlinear load (EN 62040-3:2001),
2.3.1 The scope of work shall comprise of UPS supply wiring to cover all RCC computers,
peripherals and communication equipment e.g. MODEMs, hubs etc. This shall also
include supply and wiring of 8 W Bulb tube for each computer workstationé any oth
emergency light points in RCC. An ac distribution board with 12 outlets (6 each of 5A.
& 5A) trom UPS supply shall also be provided.
2.3.2. The manufacturer shall purchase the UPS system from reputed suppliers like Aplab,
APC, Hi-Rel, Emerson network power, Dubas, Numeric & Uniline, and its inspection
shall be carried out by purchaser at the time of routine testing to verity the key functional
requirements, The responsibility of ensuring good quality & service performance of UPS,
system lies with the manufacturer.
Pave 14 of TL