EU DECLARATION OF CONFORMITY
issued according to the Directive 768/2008/EC, as amended
We, SENSIT s.r.o.
Skolni 2610
756 61 Roznov pod Radhostém
Czech Republic
Declare under our sole responsibility
that the characteristics of the below-lsted products meet the requirements of the basic safety principles and the requirements of
the technical documentation and that they are safe for the determined purpose of use under the Condition of proper installation,
operation and maintenance,
All products introduced to the market were subject to measures taken to guarantee their conformity with the technical
documentation and with the basic requirements of the below-listed technical standards
Name of the product: Temperature sensors with a stem and a plastic head with resistance output
Product line: S 120 — with grommet, $ 120K — with connector
Standard variants: NS 120, NS 120R, NS 121, NS 122, NS 123, NS 320, NS 321, PTS 120, PTS 220, PTS 320,
HS 120, OS 120
NS 120K, NS 121K, NS 122K, NS 123K, NS 320K, NS 321K, PTS 120K, PTS 220K, PTS 320K,
HS 120K, DS 120K’
Custom variants HS 12%, KTS 12x, BS 12x
HS 12xk, KTS 12xK, BS 12xK
(where xis @ number corresponding to the type of sensor)
Description and use:
‘These resistance sensors are intended for temperature measurement of chemically non aggressive gas and liquid substances
‘The sensors can be utlised for any control systems that are compatible with different sensing element output signals, for
‘example Pt 100, Ni 1000, KTY, DS 18B20. The standard temperature range in which the sensors can be ullised is -60 to
150°C (according to the sensor). The maximum temperature around the plastic head is -30 to 100°C, this range must not be
‘exceeded even for a short time. By increasing the length of the stem about 60 mm, the sensor can be used at temperatures up
to 250°C. The sensors meet the IP 65 ingress protection requirements according to EN 60 529. The variant with central holder
cor with thermowell, which are delivered as accessories, is established for temperature measurement for example in air condition
ducts, oF in pipes.The sensors are designed to be operated in chemically non-aggressive environment, the method of using
‘must be chosen with regard to temperature and chemical resistance ofthe tube and the plastic head,
‘The product that is subject to this declaration is in accordance with the following norms and standards:
~ European Parliament and Council Directive 2011/35/EU of 8 June 2011 on the restriction of the use of certain hazardous
substances in electrical and electronic equipment and Commission delegated Directive 2015/863/EU of 31 March 2015
‘amending annex Il to Directive 201 1/65/EU, as amended --- exemption in accordance with Annex Ill point 7a)
= EN 60 529, EN 60 751, EN 60730-1, EN 60730-2-9 as amended
The declaration is issued on the base of the following certificates
~ EN60 529 Certificate No. FTZU 08 E 0033 of 16 December 2008 issued from the Insttute FTZU,
Ostrava Radvanice, supplemented by the test report No. 14.0410-6 of 8 December 2014,
issued from the institute FTZU, Ostrava Radvanice:
Rotnov pod Radhostém, date: 1. 12,2015 Jeno
ing. Pet Brzezina
ceo"
Tel: +420 571-625571 Postal address SENSIT sro 64087484
Fax. +420 671-625572 Skoini 2610 cz64087484
E-mail: obchod@sensit.cz 756 81 Roznov p. R. \siL.cz_
Ceech Republic
stov EU_Declaration_$12001e.doeEU DECLARATION OF CONFORMITY
issued according to the Directive 768/2008/EC, as amended
We, SENSIT s.r.0.
Skolni 2610
756 61 Roznov pod Radhostém
Czech Republic
Declaro under our gole responsibility
that the characteristics of the below-listed products meet the requirements of the basic safety principles and the requirements of
the technical documentation and that they are safe for the determined purpose of use under the condition of proper installation,
operation and maintenance
All products introduced to the market were subject to measures taken to guarantee their conformity with the technical
documentation and with the basic requirements of the below-listed technical standards,
Name of the product: Temperature sensors with cable, with thread and case diameter 4.5mm
Product line: NS 130Rs, NS 130RsiK
Description and use:
‘The temperature sensors NS 130Rs, NS 130Rs/K are designed for measuring temperatures of gaseous and liquid substances
‘The sensor consists of a metallic stem with the sensing element inside and a supply cable. The sensor stem is made of
stainless steel DIN 1.4301. The sensors can be connected as two-wire probe. The supply cable has external silicone insulation
{and is shielded. The shielding is not connected with the housing. However, the shielding it is connected to one wire of the
temperature sensor The standard length of housing is 70 mm. The NS 130Rs / K version includes a terminal box. The
temperature sensor is connected to the terminal box and itis possible to connect the supply cable from the control system into
the terminal box.
The temperature range for application of the sensor is ~ 30°C to 150 °C. The sensors may be used for all control systems
compatible with the Ni 1000 temperature sensor with 2 temperature coefficient of 5000 ppm /"C. They meet the ingress
protection IP67 according to the EN 60 529 standard, The design of the stem allows to use the sensor for direct measuring
inside the pipe and to provide fast response to temperature changes against the temperature sensor with thermowell. The
sensors are suitable for temperature measurement in chemically non-aggressive environments, the using must be chosen with
regard to temperature and chemical resistant housing and a cable.
The product that is subject to this declaration is in accordance with the following norms and standards:
+ European Parliament and Council Directive 201//8S/EU of 8 June 2011 on the restriction ofthe use of certain hazardous
substances in electrical and electronic equipment, as amended
EN 60720-1, EN 60730-2-9, EN 60751 and EN 60 529
‘The declaration is issued on the base of
- EN60529 Cerificate No, 97 E 0229 of 29 November 1997, issued Physical - Technical Testing
Institute, Ostrava-Radvanice, Czech Republic
following certificates:
Roznov pod Radhostém, date: 1. 12. 2018 Markit Ww
os
Ing. Petr Brzezina
executive director of the company
Tel: +420 571-625571 Postal address SENSIT s.r0. Ic 64087484
Fax: +420 571.625572 Skoini 2610 DIC: Czea087484
E-mail: obchod@sensit.cz 756 61 Roznov p. R. wunw.sensit.cz
Czech Republic
siov EU_Deciaration_Ns130Rs01c.doc