Professional Documents
Culture Documents
Networks
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
The information in this document applies solely to the hardware/software product (“Product”) specified
herein, and only as specified herein.
This document is intended for use by Nokia Solutions and Networks' customers (“You”) only, and it may not
be used except for the purposes defined in the agreement between You and Nokia Solutions and Networks
(“Agreement”) under which this document is distributed. No part of this document may be used, copied,
reproduced, modified or transmitted in any form or means without the prior written permission of Nokia
Solutions and Networks. If you have not entered into an Agreement applicable to the Product, or if that
Agreement has expired or has been terminated, You may not use this document in any manner and You
are obliged to return it to Nokia Solutions and Networks and destroy or delete any copies thereof.
The document has been prepared to be used by professional and properly trained personnel, and You
assume full responsibility when using it. Nokia Solutions and Networks welcome Your comments as part of
the process of continuous development and improvement of the documentation.
This document and its contents are provided as a convenience to You. Any information or statements
concerning the suitability, capacity, fitness for purpose or performance of the Product are given solely on
an “as is” and “as available” basis in this document, and Nokia Solutions and Networks reserves the right
to change any such information and statements without notice. Nokia Solutions and Networks has made all
reasonable efforts to ensure that the content of this document is adequate and free of material errors and
omissions, and Nokia Solutions and Networks will correct errors that You identify in this document. But,
Nokia Solutions and Networks' total liability for any errors in the document is strictly limited to the correction
of such error(s). Nokia Solutions and Networks does not warrant that the use of the software in the Product
will be uninterrupted or error-free.
NO WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
ANY WARRANTY OF AVAILABILITY, ACCURACY, RELIABILITY, TITLE, NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RELATION TO THE
CONTENT OF THIS DOCUMENT. IN NO EVENT WILL NOKIA SOLUTIONS AND NETWORKS BE
LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF
PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA THAT MAY
ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT, EVEN IN THE CASE OF
ERRORS IN OR OMISSIONS FROM THIS DOCUMENT OR ITS CONTENT.
This document is Nokia Solutions and Networks’ proprietary and confidential information, which may not be
distributed or disclosed to any third parties without the prior written consent of Nokia Solutions and
Networks.
Nokia is a registered trademark of Nokia Corporation. Other product names mentioned in this document
may be trademarks of their respective owners, and they are mentioned for identification purposes only.
Copyright © 2016 Nokia Solutions and Networks. All rights reserved.
Only trained and qualified personnel may install, operate, maintain or otherwise handle this
product and only after having carefully read the safety information applicable to this product.
The safety information is provided in the Safety Information section in the “Legal, Safety and
Environmental Information” part of this document or documentation set.
Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of its
products and services. We would like to encourage you as our customers and users to join us in working
towards a cleaner, safer environment. Please recycle product packaging and follow the recommendations
for power use and proper disposal of our products and their components.
If you should have questions regarding our Environmental Policy or any of the environmental services we
offer, please contact us at Nokia Solutions and Networks for any additional information.
2 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
Table of Contents
This document has 27 pages
1 RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing............... 6
1.1 RAN3060 Benefits..........................................................................6
1.2 RAN3060 Functional description....................................................6
1.3 RAN3060 System impact............................................................... 8
1.4 RAN3060 Reference data.............................................................. 9
2 Activating RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing.
11
3 Verifying RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing...
14
4 Deactivating RAN3060: Flexi Multiradio BTS Antenna Rx RF-
sniffing.......................................................................................... 18
5 Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing.....
20
5.1 Test case 1: RF-scanning.............................................................20
5.2 Test case 2: PIM simulation......................................................... 23
5.3 Test case 3: PIM desensitization..................................................25
Issue: 01 3
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
List of Figures
Figure 1 RFI and PIM testing in commissioning BTS settings..........................12
Figure 2 RF Monitoring..................................................................................... 14
Figure 3 RF-scan visualization......................................................................... 16
Figure 4 PIM desensitization visualization........................................................17
Figure 5 RF monitoring in BTSSM....................................................................21
Figure 6 RF-scanning measurement result for Raw Composite Rx or
Composite Rx..................................................................................... 22
Figure 7 RF-scanning measurement result for Carrier Rx................................23
Figure 8 PIM simulation test result................................................................... 25
Figure 9 PIM desensitization test result............................................................27
4 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
List of Tables
Table 1 RAN3060 hardware and software requirements.................................. 9
Table 2 New parameters introduced by RAN3060.......................................... 10
Table 3 RAN3060 Sales information............................................................... 10
Issue: 01 5
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
• The feature introduces OPEX savings by eliminating the need of expensive and labor
extensive site portable PIM analyzer to detect degraded uplink performance caused
by poor site infrastructure or cabling.
• The feature provides the automatic detection and evaluation of RFI and PIM.
• The feature provides a faster and easier approach to monitor radio frequency
performance that can be used to optimize and alleviate disturbances.
6 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
The introduction of this feature provides an automated tool set for RF-sniffing or
scanning and PIM test, which allow operators to retrieve RF performance data that can
identify the occurrence of RFI and PIM. The retrieved RF data can be visualized and
analyzed remotely by using BTSSM.
BTS test mode
• On-line tests refer to the retrieval of RF measurements that are executed
exclusively within the BTSSM.
• Off-line test refers to the retrieval of RF measurement that sets the BTS to test
dedicated mode.
• RF-sniffing/scanning
RF-sniffing or scanning supports the measurements of RFI sources in the uplink (UL)
channel after the installation or commissioning of a new site to ensure that there is
no internal and external interference or to investigate if the UL performance is
degraded or degrading slowly over time. RF-sniffing/scanning has the following
options:
– Raw composite Rx
– Composite Rx
– Carrier Rx
g Note: The real-time visualization of the streaming data is not supported. Only the
visualization of the post-processed or captured data is provided.
Issue: 01 7
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
BTSSM supports the following reports:
• mean square spectrum
This is a two-dimensional plot that shows power density versus frequency. It
describes the power distribution of the intermediate frequency (IF) signal with respect
to the frequency
• spectrogram
This is a three-dimensional plot, which shows the distribution of the received power
over frequency, that is changing over time.
• max, min, average-power
This is a two-dimensional plot that is based on the spectrogram with the frequency
and power as the x and y axes, respectively. It shows the maximum, minimum, and
average power depending on the frequency.
[bts_site_name]_[test_name]_[mmddyyhhmmss]_[file#].smdf
where:
test_name=scan_test for RF-sniffing/scanning or pim_desen for PIM channel
desensitization test
bts_site_name= wbtsName
mmddyyhhmmss= date and start time of the test
file#= uniquely identifies the file created within the same test
.smdf= special extension dedicated to the suite of tests
g Note: PIM simulation test does not require a file transfer and therefore, not defined in
the naming convention.
8 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
Table 1 RAN3060 hardware and software requirements
RAS IPA-RNC mcRNC Flexi Flexi Flexi Lite
Multiradio Multiradio 10 BTS
BTS BTS
WCDMA 16 Support not Support not WBTS16 WBTS16 Not planned
required required
This feature supports the following hardware:
• RF module for RFI
– FXEB
– FXCB
– FXDB
– FHDB
– FHFB*
– FRCG*
– FRGS
– FRGT
– FRGU*
– FRGY*
– FXFC
– FRGP-B
– FXFA
– FXFB
– FXEA
– FXCA
Issue: 01 9
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
– FXDA
– FXDJ
– FHDA
g Note: The RFI support for FHFB, FRCG, FRGU, and FRGY RF modules will be
available in future maintenance releases.
• RF module for PIM:
– FXEB
– FXCB
– FXDB
– FHDB
– FHFB*
– FRCG*
– FRGS
– FRGT
– FXFC
g Note: The PIM support for FHFB, and FRCG will be available in future maintenance
releases.
Alarms
There are no new alarms related to this feature.
Measurements and counters
There are no new measurements or counters related to this feature.
Key performance indicators
There are no key performance indicators related to this feature.
Parameters
Table 2 New parameters introduced by RAN3060
Full name Abbreviated name Managed object
Activate RFI testing actRfiTesting BTS
Activate PIM testing actPimTesting BTS
Commands
There are no commands related to this feature.
Sales information
Table 3 RAN3060 Sales information
BSW/ASW SW component License control in network
element
ASW RAN BTS licence key (LK)
10 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Activating RAN3060: Flexi Multiradio BTS Antenna Rx
RF-sniffing
The licenses must be transferred and installed in the BTS for the feature to be activated.
For more information on licensing, see Licensing.
Procedure
1 Open the License Management dialog box in the BTS site manager.
Go to Configuration ► License Management
Step result
Listed are the BTS features and licenses.
Issue: 01 11
Activating RAN3060: Flexi Multiradio BTS Antenna Rx RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
RF-sniffing
g Note: The feature has two separate license codes, therefore perform step 2 and 3 for
each license.
g Note: NetAct application can alternatively be used.
Sub-steps
Figure 1 RFI and PIM testing in commissioning BTS settings
12 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Activating RAN3060: Flexi Multiradio BTS Antenna Rx
RF-sniffing
Result
Expected outcome:
The RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing feature has been activated.
RFI and PIM testing are now supported in the BTS.
Issue: 01 13
Verifying RAN3060: Flexi Multiradio BTS Antenna Rx RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
RF-sniffing
Procedure
2 Select RF Monitoring
Figure 2 RF Monitoring
14 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Verifying RAN3060: Flexi Multiradio BTS Antenna Rx
RF-sniffing
e) Click Start.
A message box will appear notifying that download is completed.
f) Click Visualize.
You will be transferred to File tab where the measurement is visible.
g Note: PIM desensitization works with RF HW 2.3 onwards.
Sub-steps
Issue: 01 15
Verifying RAN3060: Flexi Multiradio BTS Antenna Rx RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
RF-sniffing
e) Click Start.
A message box will appear notifying that download is completed.
f) Click Visualize.
You will be transferred to File tab where the measurement is visible.
Result
Expected outcome:
RF scan data is retrieved and visualized in BTSSM.
PIM desensitization is retrieved and visualized in BTSSM.
g Note: If the result does not show too high desensitization value, then increase the TX
power value gradually in Step 4.
Figure 3 RF-scan visualization
16 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Verifying RAN3060: Flexi Multiradio BTS Antenna Rx
RF-sniffing
Figure 4 PIM desensitization visualization
Issue: 01 17
Deactivating RAN3060: Flexi Multiradio BTS Antenna RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
Rx RF-sniffing
Procedure
1 Open the License Management dialog box in the BTS site manager.
Go to Configuration ► License Management
Step result
Listed are the BTS features and licenses.
g Note: The feature has two separate license codes, therefore perform step 2 for
each license.
g Note: NetAct application can alternatively be used.
18 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Deactivating RAN3060: Flexi Multiradio BTS Antenna
Rx RF-sniffing
Sub-steps
Result
Expected outcome:
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing feature has been deactivated.
RFI scanning and PIM desensitization testing are now disabled in the BTSSM.
Issue: 01 19
Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF- RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
sniffing
20 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF-
sniffing
Procedure
Figure 5 RF monitoring in BTSSM
6 Click Start.
A message box will appear notifying that download is completed.
7 Click Visualize.
You will be transferred to File tab where the measurement is visible.
Issue: 01 21
Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF- RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
sniffing
Figure 6 RF-scanning measurement result for Raw Composite Rx or Composite
Rx
9 Click Start.
You will be transferred to File tab where the measurement is visible.
22 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF-
sniffing
Figure 7 RF-scanning measurement result for Carrier Rx
Result
Expected outcome:
The operator is notified that the test results file has been retrieved.
The operator is presented a view of the test files specifying:
• Filename– name of the test file
• testType– type of test data that the file contains
• dateExecuted – date and time the file was created (representing the time of test
execution)
The BTSSM does the following:
• displays RF-scanning results as plot
• makes the RF-scanning test results file available to the operator in hdf5 format
Test results are possible to save in the OS managed file system and as well as to save
as picture to the desired folder.
Issue: 01 23
Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF- RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
sniffing
Procedure
24 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF-
sniffing
5 Click Simulate.
Figure 8 PIM simulation test result
Result
Expected outcome:
PIM simulation test is executed in BTSSM.
BTSSM displays PIM Simulation results as plot.
Unexpected outcome:
If not all of the required parameters are specified or values are out of range, then the
operator is notified of the error via an error message. All the required parameters must
meet the criteria.
Issue: 01 25
Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF- RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing
sniffing
Procedure
5 Click Start.
A message box will appear notifying that download is completed.
6 Click Visualize.
You will be transferred to File tab where the measurement is visible.
26 Issue: 01
RAN3060: Flexi Multiradio BTS Antenna Rx RF-sniffing Testing RAN3060: Flexi Multiradio BTS Antenna Rx RF-
sniffing
Figure 9 PIM desensitization test result
7 Repeat Step 4 to Step 8 for the rest of the antenna and different cell powers.
Result
Expected outcome:
The PIM Desensitization test is executed in BTSSM.
If all the required parameters meet the criteria, then PIM Desensitization test is started.
The BTSSM displays PIM Desensitization Test results as plot.
Test results are possible to save in the OS managed file system and as well as to save
as picture to the desired folder.
Issue: 01 27