OLC-D1, OLCKI
Level monitoring
The OLC series consists of a screw-in prism unit,
and an optical level detection device. The prisms,
installed in the compressor or the vessel and is not
included with the OLC. The level detection device
‘can be replaced without opening to the compressor
or the vessel. Detection of the level is via infrared
_light.There isa built-in monitoring system for correct.
Installation.
Oil level monitoring in compressors
‘The OLC series are used for contactless oil level
‘monitoring in compressors in order to safeguard
sufficient lubrication of the internal mechanics.
As the refrigerant can be absorbed by oll, fluctua-
tion of the oil level in the compressor is common in
refrigeration systems and thereby oil levels need to
be monitored.
OLC-K1 is for piston compressor use and opens
the relay after 90 seconds whereas the OLC-D1 is
for screw compressors and opens the relay after 5
seconds delay.
Level monitoring in vessels
The OLC-D1 is meant for level monitoring in vessels.
and does not have the operation recognition input,
D1.
‘The OLC-D1 releases the relay if the level is too low
and activates the relay ifthe levels valid. There isa
5 seconds time delay between switching the relay.
BLodam
BY BITZER GROUP
Oil Level Control |
ade
Optical Level Monitoring Device
Red LED status light_
‘At startup, the OLC will flash shortly with the LED.
After approx.3 seconds the relay will be activated.
For OLC-D1 the level monitoring starts immediately,
forthe OLC-K1 monitoring starts when the D1 signal
is applied and after the 90 seconds delay time the
levels evaluated.
If the oil level is too low or there isa failure, the relay
will be opened and the LED will signal the failure.
LED off: Oil level good, no failures
LED On: Oil level low
LED lashing: OLCnot correctly mounted, or
Supply voltage too low, or
Internal failure
Lock-out state
The OLC-D1 and OLC-K1 will lock-out in case of
failure. The OLC-K1 will further lock-out in case of low
oil level.
Reset of lock-out state
Interrupt power supply for 5 seconds.
Lodamelectronicsa/s | Te. 4573423737 | ladam@ledamcom
Keeve| 77 | Faxs48 72423730 wnwtlodamcam*
{400 Sonderborg
Denmarkthout no
tte chang
contents
Schematic Wiring Diagram
Supply OLCDI-T1SVEAC TIS VsI0N%, S0/6OHE
(O1C-D1-230 AC 230¥s10% 50/60Hz
OLCKI-115V: AC 115 V210%,SO/6OHz 82
‘OLC-K1-230V; AC230 Vs 10%, 50/60Hr
‘OLC-D1-24V: AC 24Vacldce 10%, SO/60HZ iar
——————-Averions v8 cy
Relay 2OVAC, 2.5A,C300- resistive load =
S24vAC/DC, >20mA
Permitted ambient Operation: -30°C-60°C 6
temperature Storage: -30°C—+80°C 6
Maxtemperatueof OLC-K1=+100°C FZ
media 1c 01: +120"
rises
Relative humidity Max. 95% r
‘Wire ength (0LC-01:950/ 2050 mm +50 mm
(OLC-K1: 1050 mm 250 mm fe
Fuse required 4A fast blow Ka
Enclosure class Housing IPS4; cable outlet pointing kore
‘downwards
Mt
Mounting ofthe Screw mounted, M24
detection circuit _-Ma.tghtening torque: 10Nm by hand a
ae IRS
ULflemumber £34818,
— ee «AT
feeoate aie a
Brown Phase
Blue NeNeutral
rey C:Common signal
orange NO; Normal open
Pink INC; Normal closed
Violet (only OLC-K1) D1; Compressor running
5152153
v
s
BLodam
BY BITZER GROUP
Lodam electronisa/s
Kaerve|77
{6400 Sonderborg
Denmark
Control unit
Contra unit of apactty regulation (option)
Main fuse
Compressor fuse
Control circuit fuse
High pressure cut-out
Low pressure cutout
Fuse of crank case heater
“Thermal overload motor PW / PZ
‘Signal ight"Compressor over temperature fault”
Signa ight “Oitsuply fault”
‘Motor contactors PW! /PW2
Time relays"part wincing’/ pause time
Compressor
Main switch
PTCsensorsin motor windings
PTC sensor in cinder head/dicharge gas tempera
‘ute sensor (option)
Crankcase heater (option)
Control switch
Solenoid valve“star unloading” option)
Solenoid valve“iquid ine”
Solenoid valve “capacity regulation (option)
‘Tel.445 73423737
Fax +45 73423730,
lodamatodam.com
| vewolodam.com