Professional Documents
Culture Documents
Installation Instructions.
Rear Seat Entertainment Retrofit
BMW 7 Series (F 01, F 02)
Retrofit kit No.: 65 12 2 154 687 Rear seat entertainment retrofit kit
65 12 2 154 408 Video switch retrofit kit
Installation time
The installation time is approx. 10.0 hours. If the video switch retrofit kit has already been installed, the installation
time will be reduced by approx. 1.0 hours. This may vary depending on the condition of the car and the
equipment in it.
The specified installation time does not include time required for programming/coding.
The charge for the total costs for the programming time is to be taken into account in when calculating the retrofit
costs (settlement must not be made via warranty).
Important information
These installation instructions are primarily designed for use within the BMW dealership organisation and by
authorised BMW service companies.
In any event, the target group for these installation instructions is specialist personnel trained on BMW cars with
the appropriate specialist knowledge.
All work must be completed using the latest BMW repair manuals, circuit diagrams, servicing manuals and work
instructions in a rational order using the prescribed tools (special tools) and observing current health and safety
regulations.
If you experience installation or function problems, limit troubleshooting to approx. 0.5 hours for
mechanical or 1.0 hour for electrical work.
In order to reduce costs and avoid any additional expense, send a query immediately to the Technical Parts Support
via the Aftersales Assistance Portal (ASAP).
Specify the following information:
- Chassis number
- Part number of the retrofit kit
- A precise description of the problem
- Work steps already carried out
Do not archive the hard copy of these installation instructions since daily updates are made by ASAP!
Pictograms
Denotes instructions that draw your attention to dangers.
!
Ordering instructions
The monitors D, monitor trims F, upper G and lower H seat back panel, the player N, the remote control U and the
batteries V are not included in the retrofit kit and must be ordered separately (see EPC for part numbers and
details).
For cars built after 9/09 the power supply wiring harness (auxiliary cable AP, auxiliary cable BA and the 10 A fuse
BB) must be ordered separately (see EPC for part numbers and details).
For cars with TV module, the TV module T and the aerial amplifier S must be ordered separately (see EPC for part
numbers and details).
If the video switch retrofit kit is installed, the video switch AA must be ordered separately (see EPC for part number
and and further details).
Section Page
2. Video switch parts list (only cars with MMC but without video switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Preparatory work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6. Video switch parts list (only cars with MMC but without video switch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
7. Connection diagram for MMC/TV/camera adapter cable (only if video switch is installed) . . . . . . . . . . . . . . 11
9. Video switch Installation and cabling diagram (only cars with MMC but without video switch) . . . . . . . . . . 13
10. Installing and connecting video switch (only cars with MMC but without video switch) . . . . . . . . . . . . . . . . 14
15. Rear seat entertainment circuit diagram for cars built up to 9/09 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
16. Rear seat entertainment circuit diagram for cars built after 9/09 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
17. Video switch circuit diagram (only cars with MMC but without video switch up to 9/09) . . . . . . . . . . . . . . . 31
18. Video switch circuit diagram (only cars with MMC but without video switch after 9/09) . . . . . . . . . . . . . . . . 32
19. Connection diagram for MMC/TV/camera adapter cable (only if video switch is installed) . . . . . . . . . . . . . . 33
A B C D E
F G H I J K L M N
BA BB
O P Q R S T U V W F01 0191 Z
Legend
AA AB AC AD AE AF
AG AH AI AJ AK AL AM AN AO AP F01 0192 Z
Legend
ISTA no.
Conduct a brief test ---
Disconnect negative pole of battery 12 00 ...
A12 A18
A11
A17
A16
A9 A10 A5 A A15
A8 A14
A13
A7
A2 A1
A6 A4 A3
F01 0107 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
Cross- Slot
section
A Rear seat entertainment retrofit
--- --- --- ---
cable
A1 20+2-pin socket casing, SW --- --- On player N A38*1B
A2 WS 4-pin socket casing --- --- On player N A38*3B
A3 VI 4-pin socket casing --- --- On player N A38*4B
A4 8+4-pin socket casing, SW --- --- To branch C1 on the seat wiring harness, left C X230
A5 8+4-pin socket casing, SW --- --- To branch B1 on the seat wiring harness, right B X231
A6 Cable open Terminal GR/RT To footwell module with miniature connector M A58*1B
58g 0.35 mm2 PIN 21
A7 Fibre optic cable connector MOST GN To disconnected fibre optic cable of CIC A42*2B
A8 Fibre optic cable MOST OR To CIC A42*2B
PIN 2
A9 Cable open CAN_H OR/GN To CIC plug with miniature connector M A42*1B
0.35 mm2 PIN 11
A10 Cable open CAN_L GN To CIC plug with miniature connector M A42*1B
0.35 mm2 PIN 9
A11 Ring eyelet, 6 mm Terminal BR To earth post on A pillar, lower right Z10*6B
31 1.0 mm2
A12 Socket contact Terminal RT/VI Cars built up to 09/09 only Z1*10B
30B 0.35 mm2 To power distribution box VR PIN 4
Cars built after 09/09 only
Insulate and tie back
A13 Socket contact FBAS_+ BL Cars with video switch only A40*1B
0.35 mm2 To video switch AA or already installed video switch PIN 11
Cars with TV module without video switch only A25*1B
To TV module T PIN 3
Cars without video switch and without TV module only
Insulate and tie back ---
A14 Socket contact FBAS_- WS Cars with video switch only A40*1B
0.35 mm2 To video switch AA or already installed video switch PIN 29
Cars with TV module without video switch only A25*1B
To TV module T PIN 9
Cars without video switch and without TV module only
Insulate and tie back ---
A12 A18
A11
A17
A16
A9 A10 A5 A A15
A8 A14
A13
A7
A2 A1
A6 A4 A3
BA
BA1 BA2
F01 0193 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation
Cross- / Slot
section
A15 Socket contact FBAS_ Shield Cars with video switch only A40*1B
shield 0.26 mm2 To video switch AA or already installed video switch PIN 47
Cars with TV module without video switch only A25*1B
To TV module T PIN 11
Cars without video switch and without TV module only
Insulate and tie back ---
A16 VI 1-pin socket casing ANT Cars with TV module only A25*5B
To TV module T
---
Cars without TV module only
Insulate and tie back
A17 Socket contact Terminal RT/BL Cars built up to 09/09 only Z2*7B
30B 0.5 mm2 To rear right power distribution box PIN 7
Cars built after 09/09 only Z2*8B
To rear right power distribution box PIN 6
A18 GN 1-pin socket casing ANT Cars with TV module only E104*1B
To aerial amplifier S
---
Cars without TV module only
Insulate and tie back
BA RSE auxiliary power supply cable --- --- Cars built after 09/09 only ---
BA1 Socket contact Terminal RT/GE On branch A1 AB8*1B
30B 0.5 mm2 PIN 10
BA2 Socket contact Terminal RT/GE To rear right power distribution box Z2*10B
30B 0.5 mm2 PIN 7
B1
B4
B3
B2 B
C1
C4
C3
C2 C
F01 0108 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
Cross- Slot
section
B Seat wiring harness, right --- --- --- ---
B1 8+4-pin pin housing, SW To branch A5 of the Rear Seat Entertainment retrofit X231
--- ---
cable A
B2 3-pin socket casing, SW --- --- To monitor D B169*1B
B3 VI 4-pin socket casing --- --- To monitor D A85*2B
B4 8-pin socket casing, SW --- --- To monitor D A85*1B
AB8 A
AB7 AB1
AB6
AB5
AB4
AB3 AB2
AP
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
Cross- Slot
section
AB Video switch retrofit cable --- --- --- ---
AB1 54-pin socket casing, SW --- --- On video switch AA A40*1B
AB2 Cable open CAN_H OR/GN With miniature connector AM to CIC A42*1B
0,35 mm2 PIN 11
AB3 Cable open CAN_L GN With miniature connector AM to CIC A42*1B
0.35 mm2 PIN 9
AB4 Socket contact FBAS_+ BL To CIC A42*1B
0.35 mm2 PIN 18
AB5 Socket contact FBAS_- WS To CIC A42*1B
0.35 mm2 PIN 28
AB6 Socket contact FBAS_ Shield To CIC A42*1B
shield 0.26 mm2 PIN 27
AB7 Socket contact Terminal RT/SW Cars built up to 09/09 only Z2*10B
30B 0.50 mm2 Insert pin in rear right power distribution box PIN 9
Cars built after 09/09 only
Insulate and tie back
AB8 Eyelet M6 Terminal 31 BR On earth post in the luggage compartment on the left Z10*12B
0.50 mm2
AC1
AC4 AC2
AC AC3
AE AE1
AE6
AE5 AE2
AE4 AF AE3
AF6 AF1
AF5 AF2
AF4 AF3 F01 0098 Z
Item Designation Signal Cable colour/ Connection location in the car Abbreviation/
Cross- Slot
section
AC MMC adapter cable --- --- Cars with MMC only ---
AC1 Socket contact FBAS_+ BL With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 3
AC2 Socket contact FBAS_- WS With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 21
AC3 Socket contact FBAS_ Shield With branch AB1 to video switch AA A40*1B
shield 0.26 mm2 PIN 39
AC4 3-pin plug casing SW --- --- To socket casing AD ---
AF Camera adapter cable --- --- Cars with camera only ---
AF1 Socket contact FBAS_+ RT With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 1
AF2 Socket contact FBAS_- WS With branch AB1 to video switch AA A40*1B
0.35 mm2 PIN 19
AF3 Socket contact FBAS_ Shield With branch AB1 to video switch AA A40*1B
shield 0.26 mm2 PIN 37
AF4 Socket contact FBAS_+ RT To RVC control unit A167*2B
0.35 mm2 PIN 2
AF5 Socket contact FBAS_- WS To RVC control unit A167*2B
0.35 mm2 PIN 3
AF6 Socket contact FBAS_ Shield To RVC control unit A167*2B
shield 0.26 mm2 PIN 4
3 4 5
A D
N
2
S
D
C
1 T AA BA
F01 0195 Z
Legend
AE AF
4
AP AB/AC 3 AA 2 1
F01 0196 Z
Legend
AA Video switch
AB Video switch retrofit cable
AC MMC adapter cable
AE TV adapter cable
AF Camera adapter cable
AP Auxiliary power supply cable for VS (for cars built after 09/09 only)
AA AK
AK
F01 0059 Z
F01 0201 Z
All cars
AH The holder AO should not be screwed firmly into
the car until all cables leading to the video switch
AJ (including Rear Seat Entertainment retrofit cable A) have
AG AO been inserted.
AI Insert Prestol cage AG and speed nut AH in car.
AB1 Plug branch AB1 into video switch.
AJ Secure the holder AO in the car using hexagonal screws
with washers AJ and hexagonal nuts AI.
F01 0109 Z
AL
F120
F01 0113 Z
All cars
If the required pins on plug A42*1B are already
assigned, disconnect cables from pins, insulate and
tie back.
AB2-AB3
Route branches AB2–AB6 to the CIC, plug A42*1B.
Connect branches AB4–AB6 as follows to plug
A42*1B 40-pin SW socket casing:
AB4-AB6 - Branch AB4, BL cable, to PIN 18
- Branch AB5, WS cable, to PIN 28
A42*1B - Branch AB6, shield, to PIN 27
F01 0114 Z
Z1*10B
F01 0202 Z
F28
AL
1
F01 0203 Z
All cars
AC1-AC3 Connect branches AC1–AC3 to branch AB1 as follows:
- Branch AC1, BL cable, to PIN 3
- Branch AC2, WS cable, to PIN 21
- Branch AC3, shield, to PIN 39
Plug branch AB1 into video switch.
AB1
F01 0117 Z
F01 0118 Z
F01 0120 Z
A11
Z1*10B
F01 0130 Z
F27
1
F01 0129 Z
All cars
Screw branch A11, M6 ring eyelet, to earth post on lower
right A-pillar Z10*6B.
A11
Z10*6B
F01 0128 Z
A8 A42*2B A42*1B
F01 0111 Z
F01 0112 Z
A58 M
F01 0123 Z
F140
F01 0126 Z
BB R
F116
F01 0205 Z
A18 S
F01 0063 Z
W
1 1
F01 0175 Z
B2 B3
D
!
F01 0066 Z
G E
J J
H
!
F01 0067 Z
K !
F 1
F01 0068 Z
B1 1
2
!
A5
F01 0069 Z
F01 0206 Z
All cars
Connect branch A1, 20+2-pin SW socket casing,
branch A2, 4-pin WS socket casing and branch A3,
N 4-pin VI socket casing to connections of same colours
on player N.
A3
A2
A1 F01 0127 Z
L 1 F01 0064 Z
A7*
A6*
A9* A10*
A1* A1*
N*/A38
01 29 2 154 688
A1* A3* A2*
A18*
2/2010
A15*
A13* A14*
C4* C2* B4* B2* C3* B3*
Z10*6B
(Z/Z)
A11*
27
15. Rear seat entertainment circuit diagram for cars built up to 9/09
Legend
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue RT Red
BR Brown SW Black
GN Green TR Transparent
GR Grey VI Violet
NT Natural WS White
OR Orange
© BMW AG, Munich 01 29 2 154 688 2/2010 (Z/Z) 28
A25
10A
A7*
30B_116 30B_118
6 7
A17* BA2* A8*
RT/GE
A6*
A9* A10*
N*/A38
01 29 2 154 688
A1* A3* A2*
A18*
2/2010
A15*
A13* A14*
C4* C2* B4* B2* C3* B3*
Z10*6B
(Z/Z)
A11*
29
16. Rear seat entertainment circuit diagram for cars built after 9/09
Legend
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue RT Red
BR Brown SW Black
GN Green TR Transparent
GR Grey VI Violet
NT Natural WS White
OR Orange
© BMW AG, Munich 01 29 2 154 688 2/2010 (Z/Z) 30
17. Video switch circuit diagram (only cars with MMC but without video switch up to 9/09)
Z2 A42
Z2*10B A42*1B
A42*1B
AB2* AB3*
A40*1B
AB1*
AA*/A40
A40*1B
Z10*12B
AB8* F01 0105 Z
Legend
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue OR Orange
BR Brown SW Black
GN Green WS White
F28
Z1 A42
17
Z1*10B A42*1B
30B_F28
A42*1B
AB2* AB3*
30B_F28
AP1* A40*1B
AB1*
AA*/A40
A40*1B
Z10*12B
AB8* F01 0200 Z
Legend
AP2* Socket contact, in plug Z2*10B of power distribution box front right Z1
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue OR Orange
BR Brown SW Black
GN Green WS White
A25 A167
AD* A25*1B
AC1*
AE4* AE5* AE6* AF4* AF5* AF6*
AC3*
AE3* AF3*
AC1* AC2*
AE1* AE2* AF1* AF2*
AB1* AB1* AB1*
Legend
All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram.
Cable colours
BL Blue SW Black
RT Red WS White