Professional Documents
Culture Documents
602 Data Sheet 133618 - Original
602 Data Sheet 133618 - Original
XLS 602
T
he XLS Series of power amplifiers from
Crown represents a new era in affordable, Features
quality power amplification. The line con-
sists of three models in a uniform, rugged • Simple, reliable design incorporates many • Electronically balanced XLR inputs and
chassis, incorporating the best of tried-and- popular features. touch-proof binding post outputs.
true design principles and innovative features.
• Selectable high-pass filter on each channel • Features precision detented level controls,
XLS Series amplifiers are professional stereo enables amplifier to work more efficiently power switch, and four LEDs, which indi-
power amplifiers engineered to meet demand- when full band-width is not required. cate clip for each channel, power and fault
ing audio requirements—reliably and within conditions.
budget. Plus, every XLS Series amplifier is • Pair of linear optocoupler clip limiters pro-
backed by Crown’s unequaled Three-Year, No- tects loudspeakers from being overdriven. • Three-Year, No-Fault, Fully-Transferrable
Fault, Fully-Transferrable Warranty that covers • Housed in a rugged, all-steel 3U chassis. Warranty completely protects your invest-
everything. ment and guarantees its specifications.
• Efficient forced-air fan prevents excessive
With over five decades of experience designing thermal buildup.
and building rock-solid products, Crown is the
standard in amp technology. So check out the
affordable, Crown XLS Series. They are a pow-
erful argument for quality and value!
Damping Factor (8 ohm) 10 Hz to 400 Hz: >200. Controls
For more details about the XLS Series, Level: Two front-panel, black rotary level
contact the Crown Technical Support Group at Crosstalk (below rated power)
controls, one for each channel.
800-342-6939 or 219-294-8200. Also, visit the at 1 kHz: –82 dB.
Crown Audio website at www.crownaudio.com. Power: Front-panel switch; on when in the UP
at 20 kHz: –58 dB. position.
Voltage Gain (at maximum output): 31 dB. Filter Switches: One per channel; three-posi-
Specifications tion back-panel switches set the frequency for
The following applies to units in Stereo mode with 8-ohm loads
Power internal high-pass filters. Frequency setting is
and rated input sensitivity unless otherwise specified. 30 Hz when switch is in left position; 15 Hz
Output Power:
when switch is centered; and bypassed when
Performance switch is in right position.
Sensitivity (volts RMS) for full rated power at Limiter Switch: Back-panel switch offers loud-
4 ohms: 1.26. speaker protection against moderate amplifier
Frequency Response (at 1 watt) 20 Hz to 20 clip when set to the “IN” position.
kHz: ±0.75 dB. Fuse: Provides overload protection.
Phase Response (degrees at 1 watt)
at 10 Hz: –10. Indicators
at 20 kHz: +19. Clip: Two front-panel red LEDs, one for each
channel, illuminate when the channel’s output
Signal-to-Noise Ratio (20 Hz to 20 kHz)
signal is being overdriven.
A-weighted, below rated power: > 100 dB.
Power: Green front-panel LED indicates
No weighting, below rated power: > 97 dB. Load Impedance: Safe with all types of loads. amplifier has been turned on and AC power
Total Harmonic Distortion (THD) at full band- Rated for 2 to 8 ohms in Stereo, 8 ohms in is available.
width power, from 20 Hz to 1 kHz: < 0.15%. Bridge-Mono.
Fault: Yellow front-panel LED illuminates when
Intermodulation Distortion (IMD): (60 Hz and AC Line Voltages Available (±10%): 120 and amplifier is in protect mode. Also illuminates
7 kHz at 4:1) from full rated output to –40 dB: 230 VAC. briefly during normal power-up when amplifier
< 0.3%. Line Frequency: 50/60 Hz. is first switched on.
XLS 602
08/01 133618-1