Professional Documents
Culture Documents
Usys Iad208e
Usys Iad208e
User Manual
V200R002
Issue 02
Date 2007-7-28
Bantian, Longgang
Shenzhen 518129
Website: http://www.huawei.com
Email: terminal@huawei.com
rights reserved.
All other trademarks and trade names mentioned in this document are
the property of their respective holders.
Notice
Release Notes
Organization
Intended Audience
Conventions
I. General conventions
Convention Description
Arial Normal paragraphs are in Arial.
Warnings, Cautions, Notes and Tips are in
Arial Narrow
Arial Narrow.
Boldface Headings are in Boldface.
Courier New Terminal Display is in Courier New.
Convention Description
The keywords of a command line are in
Boldface
Boldface.
Convention Description
Button names are inside angle brackets. For
<>
example, click the <OK> button.
Format Description
Press the key with the key name inside
<Key> angle brackets. For example, <Enter>,
<Tab>, <Backspace>, or <A>.
V. Mouse operation
Action Description
Press the left button or right button quickly
Click
(left button by default).
Press the left button twice continuously and
Double Click
quickly.
VI. Symbols
Environmental Protection
Table of Contents
i
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
ii
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
iii
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
iv
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
Chapter 7 Troubleshooting...........................................................7-1
7.1 Common Fault-locating Methods .......................................7-1
7.1.1 Showing Important System Information ..................7-1
7.1.2 Showing Alarms.......................................................7-5
7.1.3 Capturing Network Packets.....................................7-7
7.1.4 Tracing Signaling.....................................................7-8
v
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
vi
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
Table of Contents
i
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
1-1
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
1-2
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
AAA
3rd party server
iOSS MRS
SoftSwitch
SoftSwitch
SIP 多媒体终端
IP Network
SG
Ephone
TMG TMG
PSTN IAD208
AMG
1-3
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
1-4
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
1-5
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
1-6
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
Service access
module VoIP service processing module TDM/DSP
POTS
Module Function
1-7
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 1 System Overview
Module Function
1-8
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
Table of Contents
i
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Item Description
2-1
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Item Description
2-2
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Item Description
2-3
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Tools &
Description
Meters
Fastening
Cross screwdriver M3
Universal tools
tools Sharp-nose pliers, diagonal pliers,
Fitter tools
pliers
Note:
The supplier should provide the list of tools and meters, and decide
the provider of the tools and meters together with the customer.
The meters must be calibrated and proved to be qualified before
they can be used.
2-4
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Steps Operation
2-5
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
The serial port is on the right part of the device’s rear panel. It is
labeled as CONSOLE. Features of serial port are: transmission rate of
9600 bit/s, without parity check, 8 data bits, one stop bit, without traffic
control.
2-6
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
The steps for connecting the serial port cable are as follows:
1) Connect female end of the serial port cable to the DB-9 male
connector on the PC or terminal that will configure
IAD208E(M).
2) Connect the DB-9 male connector of the serial port cable to
the configuration port of IAD208E(M).
2-7
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
Caution:
To ensure safe operation, you must power on IAD208E(M) after all the
other cables have been installed and the installation check has been
passed.
2-8
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 2 Installing Hardware
2) Insert the output end of AC-DC power cable into the power
socket on the back panel of IAD208E(M), and the other end
into the external AC power socket.
3) Check whether the power indicator (PWR) on the front panel
is normal. When the local power supply is used, the PWR
indicator on the front panel is lighted.
2-9
User Manual
U-SYS IAD208E(M) Integrated Access Device Table of Contents
Table of Contents
i
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
3-1
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
3-2
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
3-3
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
4) Set the parameters of serial port: baud rate as 9600 bit/s (it
must be consistent with that configured on IAD208E(M)
serial port, and the default value is 9600 bit/s), data bit as 8,
1 stop bit, without parity check and flow control. The settings
are shown in Figure 3-4.
3-4
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
3-5
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
6) Click the <ASCII Setup> button, set the "Line delay" and
"Character delay" of the "ASCII sending" as 50ms, as shown
in Figure 3-6.
3-6
User Manual
U-SYS IAD208E(M) Integrated Access Device Chapter 3 Updating Software
3-7