Professional Documents
Culture Documents
®
WKM
DISTRIBUTED VALVES
TABLE OF CONTENTS
®
WKM DYNASEAL 210
DUCTILE IRON FLOATING BALL VALVES
How To Order 1
Features and Benefits 2&3
Detail View, Sizes, Standards and Specifications 4
Materials List 5
Dimensions and Weights 6
®
WKM DYNASEAL 310
FLOATING BALL VALVES
How To Order 7&8
Features and Benefits 9 & 10
Exploded View 11 & 12
Trim Chart 13
DIMENSIONAL DATA
4 in. (100 mm) Reduced Port and Smaller 14 & 15
Features and Benefits 16 & 17
Exploded View 18
Trim Chart 19
DIMENSIONAL DATA
4 in. (100 mm) Full Port and Larger 20 & 21
Pressure/Temperature Charts 22 & 23
Weights 24 & 25
Flow Characteristics 25
Stem Torques 26 & 27
WKM DynaSeal
Material Selection Guide 28 through 34
TRADEMARK INFORMATION 35
® CT-WKM-DYNASEAL210/310
WKM 04/07 NP-5M
DISTRIBUTED VALVES
J0XXXXX - 2 1 X X X 0 X
Base Part Pressure Rating Body Seat Seal Ball & Handle
Number (CWP) Material Trim Material Stem
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 1
DISTRIBUTED VALVES
This rugged but economical The WKM DynaSeal 210 ball valve is a two piece design with a ductile
ductile iron ball valve is iron body and tailpiece. This valve is economical and it includes many of
ideal for threaded end the premium design features found in the WKM DynaSeal 310 carbon
oilfield applications where steel ball valve.
carbon steel body material It is available in 1 in. (25 mm) to 4 in. x 3 in. (100 mm x 80 mm) sizes.
is not a requirement. Working pressures offered are 750, 1,000, 1,500 and 2,000 psi.
(See size/pressure table on page 4).
This valve is primarily used in the oilfield market for the following
applications.
Handle provides
positive indication of
Positively retained open/ closed position.
stem cannot be
removed with
valve in service.
Double
O-Ring
stem seal.
Stem gasket
reduces torque Recessed “deep pocket”
and provides a seat is protected
secondary stem seal. from flow.
2 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 3
DISTRIBUTED VALVES
Handle (Optional)
Bolt
Retainer Ring
Stop Pin
Stem O-Rings
Stem
Ball
Tailpiece Gasket
Tailpiece
Seat Rings
UNIDIRECTIONAL BALL
4 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
STANDARD MATERIALS
Qty. DESCRIPTION MATERIAL
1 Body ASTM A395 Ductile Iron
Note: For H2S service use Trim Code -X13220X. Meets NACE MR0175 (Rev. 2002) (see “How To Order” page 1).
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 5
DISTRIBUTED VALVES
F F
E E
BORE BORE
B DIA B DIA C
PIPE
DIMENSIONAL DATA
SIZE DIMENSION A APPROXIMATE DIMENSIONS in inches
in. THREADED GROOVED B C E F G
1 FP 4.00 - 1.00 1.00 2.77 4.0 7.1
2 RP 5.55 5.25 1.50 2.00 3.56 4.9 7.1
2 FP 6.00 - 2.00 2.00 4.50 4.9 15.0
2 1/2 RP 7.00 - 2.00 2.50 4.50 4.9 15.0
3 RP 7.25 7.25 2.00 3.00 4.50 4.9 15.0
3 FP 8.75 - 3.00 3.00 5.66 6.0 15.0
4 RP 8.75 8.88 3.00 4.00 5.66 6.0 15.0
SIZE mm APPROXIMATE DIMENSIONS in millimeters
25 FP 102 - 25 25 70 102 180
50 RP 141 133 38 50 90 124 180
50 FP 152 - 51 50 114 124 381
65 RP 178 - 51 65 114 124 381
80 RP 184 184 51 80 114 124 381
80 FP 222 - 76 80 144 152 381
100 RP 222 226 76 100 144 152 381
6 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
Actuator Code
Seal Seal Tailpiece Gasket Wrench* WR
Number Material Material
Oval Handwheel OH
01 PTFE PTFE
Worm Gear WG
42 Filled PTFE PTFE
Bare Stem BS
43 Homopolymer Acetal Plastic PTFE
Less Gear LG
07 FKM PTFE
Less Wrench LW
18 HPT-2 Filled PTFE
* Wrenches are part of the valve assembly
23 Celcon PTFE on 4R bore and smaller valves.
28 Filled PTFE Filled PTFE In 4 in. F through 8 x 6 in.
(100 mm F through 200 x 150 mm) they
48 Homopolymer Acetal Plastic Filled PTFE are sold separately.
60 Stellite Filled PTFE
92H 316 SS with Chrome Carbide & Filled PTFE Filled PTFE 310 2-PIECE VALVE TYPES
SIZE in. (mm) Female Thread Male x Female
1/4 (8) FP B138 -
3/8 (20) FP B138 -
310 2-PIECE VALVE TYPES 1/2 (15) RP B136 B136 (M x F)**
SIZE 150 RF 300 RF 300 BW 600 RF 600 RJ 1/2 (15) FP B138 -
in. (mm) LP* SP* LP* SP* Butt Weld 3/4 (20) FP B138 B138 (M x F)**
** 1/2 (15) FP B112 - B130 - - - - 1 (25) RP B136 B136 (M x F)**
** 3/4 (20) RP B102 - B122 - - - - 1 (25) FP B138 -
** 1 (25) RP B102 - B122 - - - - 1 1/2 (40) FP B138 -
1 (25) FP B110 - B128 - - B182 B172 2 (50) RP B136 -
1 1/2 (40) FP B110 - B128 - - B182 B172 2 (50) FP B138 -
2 (50) RP B100 - B120 - - B114 B170 3 (80) FP B138 -
2 (50) FP B110 - B128 - - B182 B172 4 (100) RP B136 -
3 x 2 (80 x 50) RP B100 - B120 - - B114 B170 ** Available in Body Tailpiece Code S8 Only.
3 (80) FP B110 - B128 - - B182 B172 Note: Threaded end valves have NPT internal pipe
thread in full conformance with ASME/ANSI B2.1 and
4 (100) RP B100 - B120 - - B114 B170 Federal Thread Handbook H-28.
4 (100) FP B110 - B128 - B150 B182*** B172***
6 (150) RP - B102 B120 - - B114*** B170*** 310 3-PIECE VALVE TYPES
6 (150) FP B110 B113 B128 - B150 B182*** B172*** SIZE in. (mm) SOCKET WELD
8 (200) RP B100 B102 - B122 - B114*** B170*** 1/4 (8) FP B103
8 (200) FP B110 - B128 B134 B150 - - 3/8 (10) FP -
10 (300) RP B100 - B120 - - - - 1/2 (15) RP B106
10 (300) FP B110 - B128 B134 B150 - - 3/4 (20) FP B103
12 (300) RP B100 - B120 - - - - 1 (25) RP B106
12 (300) FP B110 - B128 - B150 - - 1 1/2 (40) FP B103
14 (350) RP B100 - B120 - - - - 2 (50) RP B106
* LP is Long Pattern, SP is Short Pattern.
** Unibody style valve.
*** The 4 in. (100 mm) and larger sizes are available in trim CS2-43-S2-WGA
(Worm Gear Operated) only.
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 7
DISTRIBUTED VALVES
This chart is an abbreviated guide to the chemical resistance and pressure/temperature limitations
of the seal materials used in the WKM DynaSeal 310 valve.
Consult your DynaSeal distributor or the WKM factory regarding questions about trim selections.
Note 1: Trim 07 and 18 should be tested for each application by actual use.
Note 2: All seal codes with the exception of 07, 60 and 92H have been fire tested (and qualified) to API 607 4th Edition requirements.
* Trim sizes smaller than 1 1/2 in. (40 mm) in trim 07 are 100% elastomeric. Sizes 1 1/2 in. (40 mm) and larger are elastomeric with a metal insert.
8 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
Packing can be
replaced without
removing valve
from line.
Stem is positively
retained, cannot
be removed with
valve in service.
Floating ball is
self adjusting,
self cleaning.
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 9
DISTRIBUTED VALVES
10 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
Tailpiece
• MSS-SP-25, 55, 72
• API 607 4th Edition (Fire Test).
Ball
OPTIONAL MATERIALS
• Bodies, Stems & Balls can be offered in
different alloys - Consult Factory.
Seat Materials:
• High Temp TFE, FKM, Stellite,
Seat Ring Chromium Carbide Coated, Acetal Plastic.
INDUSTRY STANDARDS COMPLIANCE
Seat Ring • ASME/ANSI B16.34, B16.5.
Tailpiece Gasket • MSS-SP-6, 25, 55, 72.
Body Plug • API 607 4th Edition (Fire Test).
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 11
DISTRIBUTED VALVES
Stem
Stop Plate
STANDARDS AND SPECIFICATIONS
Bonnet Cap • To 5000 psi in small sizes
Cap Screws • Trim 43 pressure range to
3000 psi in 1/4 in. (8 mm) to 3 in. x 2 in.
Body (80 mm x 50 mm) Threaded End Valves
Tailpiece Gasket
Seat Ring OPERATING TEMPERATURES
• From -50°F to 600°F (-46°C to 316°C)
Ball
STANDARD MATERIAL
Seat Ring
Body:
• Carbon Steel and Stainless Steel
Ball/Stem:
• Carbon Steel, Stainless Steel and Monel
FLANGED ENDS Seat/Seal Trims:
Retainer Ring
• TFE, Filled TFE, Acetal Plastic, HPT-2,
Compression Ring 316 Stainless Steel with
Chromium Carbide and FKM
Packing
INDUSTRY COMPLIANCE:
Stem Seal Handle
Tailpiece Seat Ring
• ASME/ANSI B16.5, B16.34
Stem
Bolt • MSS-SP-6, 25, 55, 72
• API 607 4th Edition
(Fire Test Specification)
Stop Plate
Cap Screws
Bonnet Cap
FLANGED CONNECTIONS
Body Stud Nut
ASME/ANSI PRESSURE CLASS
Body Stud
SIZE CLASS
Ball
in. (mm) 150 300 600
Seat Ring 1 (25) FP • • •
Tailpiece Gasket 1 1/2 (40) FP • • •
2 x 1 1/2 (50 x 40) RP • • •
Body
2 (50) FP • • •
3x2 (80 x 50) RP • • •
3 (80) FP • • •
4x3 (100 x 80) RP • • •
12 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
ACTUATOR CODE
PART (BODY) CS CS2 CS3 S1 S8
Lock Nut* Alloy Steel Alloy Steel Alloy Steel Alloy Steel Stainless Steel
Handle* CS Zinc Plated CS Zinc Plated CS Zinc Plated CS Zinc Plated Stainless Steel
Handle Grip* Vinyl Vinyl Vinyl Vinyl Vinyl
Wrench Handle** Ductile Iron Ductile Iron Ductile Iron Ductile Iron Ductile Iron
Wrench Head Bolt & Nut** Alloy Steel Alloy Steel Alloy Steel Alloy Steel Alloy Steel
Stop Plate Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel
* 2 inch (50 mm) Reduced Port and smaller.
** 2 inch (50 mm) Full Port and larger.
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 13
DISTRIBUTED VALVES
1 in. (25 mm) REDUCED PORT AND SMALLER Q 1 in. (25 mm) FULL PORT THROUGH
2 in. (50 mm) REDUCED PORT
S X Q
STEM
J DIMENSIONS
S
STEM
H J DIMENSIONS
J T
G H T
J
W
G
F
E
W
B
D BORE F
DIA E
A
BORE
G B DIA C DIA
X
D
W F
A
E
2 in. (50 mm) FULL PORT THROUGH
BORE
C DIA B DIA 4 in. (100 mm) REDUCED PORT
D J R
S
STEM
A DIMENSIONS
H Q H
S J
UNIBODY J STEM X T
DIMENSIONS
DESIGN
G
J T
G
X
W W
F
F E
E
BORE
B B DIA C DIA
BORE
D DIA D
A
A
UNIBODY VALVES - FLANGED ENDS
A Approximate Dimensions in inches
SIZE 150 Flg 300 Flg 150 Flg 300 Flg
in. B102 B122 B112 B130 B D E F G H* J Q* S T W X
1/2 FP - - 4.25 - 0.50 1.75 1.8 3.5 5.8 10-24 .38 DP 1.0 7/16-20 0.246 0.41 0.72 0.38
- - - 5.50 0.50 1.88 1.8 3.5 5.8 10-24 .38 DP 1.0 7/16-20 0.246 0.41 0.72 0.38
3/4 RP 4.62 - - - 0.50 1.94 1.8 3.5 5.8 10-24 .31 DP 1.0 7/16-20 0.246 0.41 0.72 0.38
- 6.00 - - 0.50 2.31 1.8 3.5 5.8 10-24 .31 DP 1.0 7/16-20 0.246 0.41 0.72 0.38
1 RP 5.00 - - - 0.75 2.13 2.3 4.0 6.7 10-24 .25 DP 1.0 7/16-20 0.246 0.48 0.84 0.38
- 6.50 - - 0.75 2.44 2.3 4.0 6.7 10-24 .25 DP 1.0 7/16-20 0.246 0.48 0.84 0.38
SIZE mm Approximate Dimensions in millimeters
15 FP - - 108 - 13 44 46 89 147 10-24 9.7 DP 25 7/16-20 6 10 18 10
- - - 140 13 48 46 89 147 10-24 9.7 DP 25 7/16-20 6 10 18 10
20 RP 117 - - - 13 49 46 89 147 10-24 7.9 DP 25 7/16-20 6 10 18 10
- 152 - - 13 49 46 89 147 10-24 7.9 DP 25 7/16-20 6 10 18 10
25 RP 127 - - - 19 54 58 102 170 10-24 6.4 DP 25 7/16-20 6 12 21 10
- 165 - - 19 54 58 102 170 10-24 6.4 DP 25 7/16-20 6 12 21 10
* American National Thread in inches.
14 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 15
DISTRIBUTED VALVES
GEAR OPERATOR REQUIRED FOR 8 in. (200 mm) FULL PORT AND LARGER.
Stop plate provides ball alignment
and visual indication of open or
ASME/ANSI CLASS 150, 300 AND 300 BW
closed position
4 in. (100 mm) FULL PORT
4 in. (100 mm) and 6 in. (150 mm)
THROUGH
bore only.
14 in. x 12 in. (350 mm x 300 mm)
REDUCED PORT
NACE MR0175 (Rev. 2002).
Packing can be adjusted
or replaced without
removing valve from line.
16 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 17
DISTRIBUTED VALVES
Stop Plate
Cap Screw
GEAR OPERATOR OPTION
Bonnet Cap
Compression Ring
Stem Packing
Body
Stem Retainer Pin
Pipe Plug
Stem
Stem Gasket
Ball
Body Stud
Drain Fitting
STANDARDS AND SPECIFICATIONS
Seat Rings
ASME/ANSI CLASS 150, 300, 600 AND 300 BW
OPERATING TEMPERATURES
Tailpiece Gasket
• From -50°F to 600°F (-46°F to 316°C)
STANDARD MATERIALS
Tailpiece • Body: Carbon Steel and Stainless Steel
• Ball/Stem: Carbon Steel, Stainless Steel & Monel
ASME/ANSI CLASS 600 INDUSTRY COMPLIANCE
Worm Gear Operator • ASME/ANSI B16.5, B16.34
• MSS-SP-25, 55, 72
• API 607 4th Edition (Fire Test Specifications)
Stud
SIZE CLASS
Stem O-Ring in. (mm) 150 300 600 300 BW
Washer
Stem Gasket 4 (100) FP • • • •
Nut
Body
Key 6x4 (150 x 100) RP • • •
Stem
6 (150) FP • • • •
Ball 8x6 (200 x 150) RP • • •
Body Stud
Body Stud Nut 8 (200) FP • • •
10 x 8 (250 x 200) RP • •
Ground Spring
10 (250) FP • • •
Drain Fitting
Seat Rings 12 x 10 (300 x 250) RP • •
12 (300) FP • • •
Tailpiece Gasket
14 x 12 (350 x 300) RP • •
Tailpiece
18 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 19
DISTRIBUTED VALVES
G
DIA J
N = KEY SIZE
F P
E R
H
BORE
B DIA
C DIA
A A
VALVE WITH WRENCH (LEVER) VALVE WITH GEAR 4 in. (100 mm)
4 in. (100 mm) THROUGH THROUGH 8 in. x 6 in. (200 mm x 150 mm)
14 in. x 12 in. (350 mm x 300 mm) CLASS 600 K
Class 150/300 DIA
P
U THROUGH U THROUGH
G W HOLE DIA W HOLE DIA
E S T
E T
H
BORE BORE
B DIA B DIA
D D V V
20 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM DYNASEAL 310 4 in. (100 mm) FULL PORT THROUGH 14 in. (350 mm) REDUCED PORT
ASME/ANSI CLASS 150, 300, 600 AND BUTT WELD 300
FULL PORT DIMENSIONS
A* Class
150 RF 300 RF 300
SIZE LONG SHORT LONG SHORT BW B C D E F G H J K L M N P R S T U V W X Y Z AA
in. B110 B113 B128 B134 B150
9.00 - - 4.0 4.0 6.47 8.63 9.88 36.0 7.56 1.250 8.0 2.80 7.88 0.250 10.84 9.15 - - 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63
4 N/A N/A
- 12.00 12.00 4.0 4.0 6.47 8.63 9.88 36.0 7.56 1.250 10.0 2.80 8.12 0.250 10.84 9.15 - - 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63
15.50 10.50 - - 6.0 6.0 8.20 11.38 12.63 48.0 9.44 1.500 14.0 2.80 10.95 0.375 12.72 11.03 - - 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63
6 N/A
- - 15.88 15.88 6.0 6.0 8.20 11.38 12.63 48.0 9.44 1.500 14.0 4.11 13.24 0.375 13.28 11.33 - - 0.56 2.44 4.921 1.88 4.63 3/8-16NC 0.63
18.00 - - - 8.0 8.0 9.95 16.38 - - 13.50 2.375 16.0 4.11 11.11 0.625 17.34 15.39 - - 0.68 4.00 5.512 3.50 8.25 1-8NC 1.13
8 N/A
- 19.75 16.50 16.50 8.0 8.0 9.97 16.38 - - 12.50 2.375 20.0 5.12 15.25 0.625 17.07 14.67 - - 0.75 3.00 - 3.50 8.25 1-8NC 1.13
21.00 - - - 10.0 10.0 11.63 18.50 - - 15.12 2.938 20.0 5.12 15.25 0.750 19.70 17.30 7.75 5.75 0.75 3.00 - 3.50 8.25 1-8NC 1.13
10 - N/A 22.38 - 22.00 10.0 10.0 11.65 18.50 - - 15.12 2.938 20.0 8.31 17.61 0.750 21.24 17.30 7.75 5.75 0.75 3.00 - 3.50 8.25 1-8NC 1.13
- - 18.00 - 10.0 10.0 11.65 18.50 - - 15.12 2.938 16.0 8.31 15.32 0.750 21.24 17.30 7.75 5.75 0.75 3.00 - 3.50 8.25 1-8NC 1.13
24.00 - - 12.0 12.0 13.97 20.13 - - 16.38 2.938 20.0 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 - 3.50 8.25 1-8NC 1.13
12 N/A N/A
- 25.50 25.00 12.0 12.0 13.97 20.13 - - 16.38 2.938 24.0 8.31 17.61 0.750 22.49 18.55 7.75 5.75 0.75 3.00 - 3.50 8.25 1-8NC 1.13
mm
A* Class
150 RF 300 RF 300
SIZE LONG SHORT LONG SHORT BW B C D E F G H J K L M N P R S T U V W X Y Z AA
in. B110 B113 B128 B134 B150
229 - - 102 102 164 219 251 914 192 31.75 203 71 200 6.35 275 232 - - 14 62 124.99 48 118 3/8-16NC 16
100 N/A N/A
- 305 305 102 102 164 219 251 914 192 31.75 254 71 206 6.35 275 232 - - 14 62 124.99 48 118 3/8-16NC 16
394 267 - - 152 152 208 289 321 1219 240 38.10 356 71 278 9.53 323 280 - - 14 62 124.99 48 118 3/8-16NC 16
150 N/A
- - 403 403 152 152 208 289 321 1219 240 38.10 356 104 336 9.53 337 280 - - 14 62 124.99 48 118 3/8-16NC 16
457 - - - 203 203 253 416 - - 343 60.33 406 104 282 15.88 440 391 - - 17 102 140.00 89 210 1-8NC 29
200 N/A
- 502 419 419 203 203 253 416 - - 318 60.33 508 130 387 15.88 434 373 - - 19 76 - 89 210 1-8NC 29
533 - - - 254 254 295 470 - - 384 74.63 508 130 387 19.05 500 439 197 146 19 76 - 89 210 1-8NC 29
250 - N/A 568 - 559 254 254 295 467 - - 382 77.45 504 212 444 22.75 535 439 197 146 19 76 - 89 210 1-8NC 29
- - 457 - 254 254 296 470 - - 384 74.63 406 211 389 19.05 539 439 197 146 19 76 - 89 210 1-8NC 29
610 - - 305 305 355 511 - - 416 74.63 508 211 447 19.05 571 471 197 146 19 76 - 89 210 1-8NC 29
300 N/A N/A
- 648 635 305 305 355 511 - - 416 74.63 610 211 447 19.05 571 471 197 146 19 76 - 89 210 1-8NC 29
22 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
THREADED VALVES
Body trim code S8 and CS3 are suitable for service to -50°F (-46°C).
All other trims are limited to operating temperatures no lower than -20°F (-29°C)
These pressure/temperature ratings are in conformance with ASME/ANSI B16.5, B16.34.
MAXIMUM WORKING PRESSURES - psig
TEMP °F BODY MATERIAL CODES
VALVE BORE CS, CS2 & CS3 S1 & S8
SIZE in. 1/4 - 3/8 1/2 - 3/4 1 - 1 1/2 2 3 1/4 - 3/8 1/2 - 3/4 1 - 1 1/2 2 3
-20 to 100 5000 3750 3000 2000 1500 5000 3750 3000 2000 1500
150 4779 3583 2867 1912 1434 4650 3487 2790 1861 1396
200 4557 3416 2734 1824 1368 4301 3224 2580 1722 1292
250 4494 3368 2696 1800 1350 4092 3068 2455 1639 1229
300 4431 3320 2658 1775 1333 3884 2912 2330 1556 1167
350 4355 3264 2613 1744 1310 3725 2794 2236 1491 1117
400 4278 3209 2567 1713 1287 3566 2677 2141 1426 1068
450 4161 3120 2496 1665 1252 3442 2583 2066 1377 1031
500 4043 3031 2425 1618 1216 3317 2489 1992 1328 995
550 3868 2900 2320 1548 1163 3225 2419 1936 1291 966
600 3694 2768 2215 1478 1110 3134 2349 1880 1254 938
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 23
DISTRIBUTED VALVES
24 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 25
DISTRIBUTED VALVES
1 (25) 120 150 180 225 - 1 (25) 120 150 180 225 300
1 1/2 (40) 240 330 420 520 - 1 1/2 (40) 240 330 420 520 720
2 (50) 500 640 810 - - 2 (50) 500 640 810 1090 1440
1 (25) 225 245 260 280 320 400 455 520 700
1 1/2 (40) 390 410 450 510 700 920 1050 1200 1550
2 (50) 860 960 1075 1210 1500 1830 2000 2200 2600
VALVE BORE SIZE DIFFERENTIAL PRESSURE VALVE BORE SIZE LIQUID DRY GAS DRY GAS
in. (mm) 0-285 500 740 1000 1500 2250 in. (mm) 0-285 psi 0-285 psi 740 psi
3/4 (20) 128 128 145 160 215 360 3/4 (20) 90 150 404
1 (25) 274 284 312 360 405 580 1 (25) 180 336 606
1 1/2 (40) 520 580 680 810 980 1390 1 1/2 (40) 420 840 2260
2 (50) 910 1042 1240 1500 1765 2300 2 (50) 900 1200 3230
3 (80) 1200 1800 2400 2900 3420 - 3 (80) 2400 3600 9690
26 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
DISTRIBUTED VALVES
3/4 (20) 108 108 125 140 190 260 340 420 560 695 800 - - -
Note: The torque values listed for 285 psi and greater are based on valves controlling the flow of clean
lubricating liquid at ambient temperature.
For valves at pressure less that 285 psi use the value for 285 psi.
Interpolation may be used for any pressure above 285 psi but less than maximum pressure listed.
Running torque values will average two-thirds of these values.
For running torque values less than breakaway torque values at 285 psi use breakaway
torque values.
Reseating torque is equal to breakaway torque.
For operating temperatures between -20°F to -50°F (-29°C to -46°C) multiply these values by 1.20.
These torque values do not contain service or safety factors.
Actuator selection should be made based on experience and appropriate service and
safety factors.
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 27
DISTRIBUTED VALVES
28 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
VTFEP - Virgin TFE Packing.
Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
30 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
VTFEP - Virgin TFE Packing.
Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
32 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
VTFEP - Virgin TFE Packing.
Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
34 WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M
VTFEP - Virgin TFE Packing.
Note: All ladings at ambient temperatures except as noted.
DISTRIBUTED VALVES
TRADEMARK INFORMATION
WKM
® CT-WKM-DYNASEAL210/310
04/07 NP-5M 35
DISTRIBUTED VALVES
NOTES
® CT-WKM-DYNASEAL210/310
WKM 04/07 NP-5M
DISTRIBUTED VALVES
DISTRIBUTED VALVES
For the most current contact and location information go to: www.c-a-m.com