Sig Sauer P226
blowback and ejection
rubber band gun
by @walt.wil.778WARNING!
This is a guide for making a
harmless printed rubber band
gun. Check your lockal laws.
Don't bring that to the public
places. Never aim at people
and take care of eye protection
Have a fun!
Contact me if you have any problems or need help:
Instagram: walt.wil.778
Facebook page: Comrade MauserPrint all the parts.
| used PET-G with 1.6mm step.
Big parts 20% infill, mechanics
parts 100% infill.
Remove all supports, brims,
artefacts from printed parts.
Sand it a little bit if necessary.
Check if the rails on the
frame and slide fits together.
Print enough shells for the test.Tools:
-Cutter with fresh blade
-Drill bits 1mm, 1.5mm, 2mm
-Hand drill or electric drill
-Hex keys 2mm and Imm
-tweezers with curved ends
-Sandparer with nr corn 120
-set of needle files
-small Pliers
Material list:
-steel wire 1mm
-instant glue
-1 package loom bands
-4x M4x8 hex screws
-spring from a broken pen ( broke one in havent broken)
-some small nails 1mm and 1.5mm diameter
-small tube 1mm diameter, for example from a penSTEP 1: Glue right frame part together.
Pay attention, that both holes are concentric.
/ FRAME RIGHT
FRAME RIGHT OUTSIDE——,
\STEP2: Glue left frame parts together.
Pay attention that holes are concentric.
Glue disassembly lever in place.
LEFT FRAME
OUTSIDE
DISASSEMBLY LEVER:STEP 3: Put both trigger parts together.
Lock it with pins together and
add some glue in the joit gaps
TRIGGER HOOK —™™
A
TRIGGER SLIDE——
\
\
A
=
PIN (1mm x emfSTEP 4: Assemble blowback unit.
Attach both hooks with pins through the holes.
Don't use any glue. Pay attention that hooks can move free.
REAR HOOK.
BLOWBACK HOUSING —~
Pin 1.5mmx8mm
FRONT HOOCKSTEP 5: Install two loom size rubber bands rings
in the square hole of the trigger hook. Fix it with pin.
Place trigger and blowback assemblys
in the grooves on the right frame side. Fix bands ends in the frame.
BLOWBACK ASSEMBLY ——_ g
‘TWO LOOM SIZE RUBBER
BANDSCheck that assembled blowback and trigger units
can slide in the groovs for- and backwards with no resistance.
TRIGGER ASSEMBLY
BLOWBACK ASSEMBLY.
(Half section view)
Check for right function! J
Pressed trigger must unlock
blowback unit. It must be able
move backwards.
BLOWBACK UNIT LOCKED sLowencx unr UNCEDSTEP 5: Put both frame halfs together, use guidance holes.
Check that trigger and blowback units can move free.
If everything ok and works properly glue both halfs together.
FRAME PARTSSTEP 6:Connect trigger and blowback units
with 3 loom size rubber rings.
Check for correct function:
If trigger pressed completly,
blowback unit must snap backwards realy fast.
Trigger released - all goes
in the basic position and locks.
ca.16mm
QSTEP7: Magazine assembly. Put magazine parts together and
attach rubber band like shown in the picture.
Don't use any glue for this step! Check for the right function.
pin mmx10mm__y
AI
piece of tube /
for example part from ——
a pen
Magazine tube ———
Follower \, \
/
‘
Bottom ed y)| esa)
“rubber bandSTEPS: Bend following part from 1mm spring steel wire:
r
3.6mm,
3.6mm
32mm
I.
2.5mm
5.1mm,STEP9: Install bended wire part in the chamber part.
Fix it in place with cover part. Glue this part to the chamber.
~ —STEP10: Connect chamber and slide
with piece of loom rubber band. Use glue to fix
rubber band in place. Insert chamber and barrel in
the slide, and lock it together. Don't use glue here.STEP11: Glue slide hook in place.
SS
Slide hook ———~Glue rear and front sights to the slide.
Install small pin for the rubber bands
in the front sight hole.STEP12: Press wire part ends through the ejection port
together and bring the slide in place.
Wire part ends must engage in the frame holes.
Check for correct function.
Blowback must work now.STEP13: Put RGB UNIT parts together. Don't use any glue.
Check function. Slightly cut or sand rotor or stoper parts edges
if necessary, so that it can cycle properly.
\
Stoper aes
we &
8
AY
Rotor
ReleaserSTEP13: Place RGB-Unit in the slade and fix it with
M2.5 grub screw. No pre cutted thread needed here.
M2.5 grub screwSTEP14: Place magazine button and spring in the frame.
Slide the grip shell over and fasten it with M4 screws.
M4 hex + flat or lense head
gripp shells
mag catch button
spring 3mm x 13mm.
ma threadYour gun is now ready and can
be tested for the proper function.Possible malfunctions:
Gun makes loud "click" but nothing happens.
Check if blowback hook can engage
in the slide hook properly. Move Slide hook (violet)
slightly for- or backwardsBlowback and ejection are Ok, but gun has
"return in to battery" failure. Slide return work not
properly.
1. Check if it slide collide with magazine.
2. Check if blowback hook goes down properly.
3. Check slide return rubber band has enough powerRubber band gun function works not properly.
Not every shoot works.
Check shapes of the RGB unit parts:Sig Sauer P226
blowback and ejection
rubber band gun
by @walt.wil.778