Professional Documents
Culture Documents
GROUP N
APPROVED VEHICLE SPECIFICATION
This form details the approved specifications of individual vehicle models in the 5th Category Historic car
group. To be issued with an Historic Log Book, cars need to comply with these specifications, the physical
appearance shown in the illustrations and the general historic rules as detailed in the current Motorsport
Australia Manual.
Refer to Motorsport Australia Manual of Motor Sport, Vehicle Eligibility, Historic Touring Cars,
General Requirements & Nc Regulations for permitted modifications.
Update Log
Page 1 of 6
SECTION 1 - CHASSIS
1.1. CHASSIS
Description: Unitary construction
Period of Manufacture: 1963 – 1964
Manufacturer: Ford Motor Company
Chassis Number From: RW66R
Chassis Number location: Top of RHS firewall
Material: Steel
Comments None
1.4. STEERING
Type: Recirculating ball Make: Ford
Comments None
1.5. BRAKES
Front Rear
Type: Disc, solid Drum
Dimensions: 276 mm x 32 mm 280 mm x 64 mm
Material of drum/disc: Cast iron Cast iron
No. cylinders/pots per wheel: Four One
Actuation: Hydraulic Hydraulic
Caliper make: Ford
Caliper type: Floating
Material: Cast iron
Master cylinder make: PBR
Type: Single
Adjustable bias: No
Servo Fitted: Yes
Comments: None
Page 2 of 6
This form was issued without alteration or erasure.
SECTION 2 - ENGINE
2.1. ENGINE
Make: Ford
Model: FE427 – side oil
FE427 – centre oil
No. cylinders: Eight Configuration: Vee
Cylinder Block-material: Cast iron Two/Four Stroke: Four
Bore - Original: 107.5 mm Max allowed: 109 mm
Stroke - original: 98.0 mm Max allowed: 96.0 mm
Capacity - original: 6966 cc Max allowed: 7162 cc
Identifying marks: Casting number is on the right (passenger) side of the block, in the front.
FE (330-428 SCJ). Note: nearly all FE blocks have 352 cast on the front of
them.
Casting number sStarts with C3AE, C4AE, or C5AE.
Cooling method: Liquid
Comments: Either the 1963 FE 427 centre oiler engine block or the 1965 side oiler engine
block (C5AE) may be used
2.3. LUBRICATION
Method: Wet sump Oil tank location: N/A
Dry sump pump type: N/A Location: N/A
Oil cooler standard: Yes Location: Front of radiator
Comments:
Page 3 of 6
This form was issued without alteration or erasure.
SECTION 3 - TRANSMISSION
3.1. CLUTCH
Make: Various
Type: Dry plate
Diameter: 215 mm
No. of Plates: One
Actuation: Hydraulic
Comments: None
3.2. TRANSMISSION
Type: Synchromesh
Make: Ford
Borg Warner
Gearbox location: Behind engine
No. forward speeds: Four
Gearchange type and location: Remote lever floor
Case material: Cast iron
Identifying marks: N/A
Comments: None
Page 4 of 6
This form was issued without alteration or erasure.
SECTION 4 GENERAL
4.3. BODYWORK
Type: Fixed head coupe Material: Steel/Fiberglass
No. of seats: Five No. doors: Two
Comments: Fibreglass panels for the doors, engine hood, front guards, and boot lid
permitted.
Bonnet must be flat.
Bumpers must be either steel or aluminium. Fiberglass not permitted.
4.4. DIMENSIONS
Track - Front: 1650 mm Rear: 1580 mm
Wheelbase: 3023 mm Overall length: 5309 mm
Dry weight: 1700 kg
Comments: Nnoe
Page 5 of 6
This form was issued without alteration or erasure.
Appendix A
Suspension
Front
Spring height adjustment permitted.
Rear
Spring height adjustment permitted.
Page 6 of 6
This form was issued without alteration or erasure.