You are on page 1of 4
INSTALLATION AND MAINTENANCE INSTRUCTIONS FCM-1 Supervised Control Module ‘SPECIFICATIONS Normal Opeating Volage: 18 v0 42 YDC Maximum Caren Draw: 65 mA (LED on) Average Operating Cure: Maximim NAC Line Ls: 4 VDC External Supply Volge (betcen Terminals 10 and THI) Maximum (NACI: Regulated 24 VDC Maximum (Speakers): 70.7 V RMS, SOW NOTIFIER by Honeywell 12. Clintonville Road Nonthiord, CT 06872-1883 Phone: 208.488 716) S758 (LED aching - in group pll mode) 880) (LED flashing in diet poll mode); 485A Max. (LED Mashing, NAC shorted) Drain on External Supply 1.7 mA Maximum using 4 VDC supply; 22.mA Maximum using 6 VRMS supply Max NAC Current Ratings: For ls B witng system, dhe current rating is 3A; For class A wiring system, the curenrating is 2A “Temperate Range 32°F 10 120°F (0°C 10 49°C) Homi 10% 19 93% Non-condensing Dimensions: 4.695" Hx 4275" Wx LAD (Mounts 1 24° square by 2/6 deep box} SMBESO0 Ek accessories al Box CBSOO Barrier RELAY CONTACT RATINGS: ‘CURRENT RATING. (MAXIMUM VOLTAGE LOAD DESCRIPTION “APPLICATION Fry 15 Wie Dre 038 Roncoded 2A s0 VDC ressive Noweeded BA. Bo VDC Resse coed DASA 30 VDC (Wa = ons) Ron-coded Ora 70.7 VAC PF= 038 Noncoded 098 125.vDC Resse Nomeoded asa Tas AC B= 078 Noneeded aA 1S VAC Pr 038 Roneeded BEFORE INSTALLING This information fs included as» qulk reference installation guide. Refer to the conto pane instalation manual for detalleé system infrmaton Ifthe ‘modules wil be installed in an existing operational sysem, inform dhe opea- for and local authority that the system wil be tempers eu of sevice. Dis ‘cones power to the contol pane before insicllng the modules. [NOMICE: This mama shouldbe left with the eener/user ofthis equipment. [GENERAL DESCRIPTION FCM Supervised Control Modules are intended fr ue in intelligent, 4 ite sens, where the individual address of each module is selected us ing the builtin folary swiches. This module i used 1 switch an external power supnly, which ean be a DC pawer supply or an audio amphi (up {0 80 VAM), 0 notification appliances. I alsa supervises the wiring 1 the connected loads and reports their eas 10 the panel as NORMAL, OPEN, for SHORT CIRCUIT. The FCM-1 has two pars of output termination points tvalable for falefolerant wing and » panel-contlled LED indictor. This module can be used io zplace M2 module that has hoen conigred for supervised wiring operation. COMPATIBILITY REQUIREMENTS To ensure proper operation, this mele shall e connected to a compatible Notifier system cont panels ony (ist avaiable from Nour) MouNTiING The FEN mounts ciel to inc square electrical boxes (se Figure 24, ‘The box must havea minimum depth of 2s inches. Surface mounted elect ‘al boxes (SM8500 are available. The module can also mount yo the DNRCW) dict housing wirine [NOTE Al wiring mt conform to spieale local odes, onances, and eg ations. When using conitel modules in nonpover ited applications. the ‘CBS00 Module Barrer must be used to meet UL requirements for the separa- tion of power-imited and nonpowelintedtsminals and wiring, The barter rst be ineried into a4” » €” 24/ Junction ox, anid the contol modvle rust be placed into the barr and atached to the [uncon box (Figure 24). ‘The powerlimied wising must be placed into the isolated quacrant of he module barrie (Figure 28) |. tnsall module witing in accordance with the job drawings and appropt ste wiring diagrams 2. Sethe address onthe modal pr jo drawings. 3, Secure module to deta box (supplied by installer), se Figure 2 Wie shoud be strppet othe appropriate length (recommenced sip length iste" Ye") Exposed conduct should be secured unde the clamping plate tnd shouk! not protrude beyond the terminal Bock a, CAUTION: Do not loop wire under terminals Beak wite run to provide 8 IMPORTANT. Whe using the FCN for audio applications, re (01) and discard. The Ju nove Jumper is located on the back as shown in Figure 1. 1 must be rernoved whenever power supply moniter feature not regu. NOTE: Al references 10 power limited represent “Poveer Limited (Cle 2 2 rfeonees 10 Cass A also include Clas. so0r00s6-951 FIGURE 16. JUMPER LOCATION: FIGURE 3. TYPICAL NOTIFICATION APPLIANCE CIRCUIT CONFIGURATION, NFPA STYLE Y: 7 ‘ vonorLoor wine BYERTIRALE 10 @ 1, oRIEAK WIRE UN TO PROVIDE SUPERVISION OF CONNECTIONS, CONTROL MODULE 2a vob POWER SUPRLT isoLaTeD, REGULATED. POWER LivtTeD PER NFPA 70 USTED FOR Fine PROTECTION lwirt BATTERY BACKUP MODULE POLARITIES ARE SHOWN INALARIA 3, oy a7 EOL, RESISTOR Etna ULUISTED EOL RELAY SHOWN TONEXT CONTROL MODULE OR ENERGIZED END-OF-LINE RELAY. ONE RELAY BRVBe CCI. REQUIRED FOR EACH CIRCUTT SOME EOLRs CONTROL PANELS HAVE RELAY BUILT WNaNo DONGT REQUIRE EYTERNAL WIRING, REFER TO PANEL MANUAL FIGURE 24. MODULE MOUNTING (WITH BARRIER: FIGURE. CONNECT MODULES TO. LsTED GoMPATIBLE CONTROL PANELS ONLY, Se FROM PANEL ooooo Cale gf PHEvous DEVICE SIGNAL LINE CIRCUIT (SLC) 2 VOC MA TWISTED PAR, Is RECOMMENDED he tovexr eee ALL WIRING SHOWN IS SUPERVISED ‘AND POWER LIMITED. “NOTE: ANY FAULT INTHE POWER SUPPLY IG LIMITED TO THAT ZONE AND DOES NOT RESULT IN A FAULT IN A SEPARATE ZONE FIGURE 4, TYPICAL FAULT TOLERANT NOTIFICATION APPLIANCE CIRCUIT CONFIGURATION, NFPA STYLEZ: zavoc CRUE : oo nor oBP RE OR Tennis so Conger Manus To sTED NUON BROMIDE PATIBLE CONT 2a woe POWER SPRY UPEEIION oF COMMECTIONS ISOLATED. REGULATED, Le FrOM paver Foner ciaseo pee conrRoL He oes NFPA 70, LISTED FOR TH MODULE {4 OF EEevicus) fine enTecnoN wird BATTERY BACK. Ge. 8-9 TOILE POLAnITeS AE a : Si aver — pao cot nesisron + Seo Pa Saene Ik ‘ Qe \sReContWENDED FeauiNas | fF ee Bands Aodt R—

You might also like