Professional Documents
Culture Documents
532K1-SC MSM-05 E MC10 A4 VOL01-1 Low
532K1-SC MSM-05 E MC10 A4 VOL01-1 Low
AS 532
SC
Airbus Helicopters
Direction Technique Support
Aéroport International Marseille Provence 13725 Marignane Cedex FRANCE
Contact: contact.msm.ah@airbus.com
MSM
RECORD OF REVISIONS
MSM
LOEDU
1 Update
N-New, to be inserted
R-Revised, to be replaced
D-To be removed from the manual
- (No code) Unchanged with respect to the previous issue
AS 532 SC
LOEDU
2021.07.28 Page 1
MSM
AS 532 SC
LOEDU
2021.07.28 Page 2
MSM
TABLE OF CONTENTS
TITLE
HIGHLIGHTS OF THE REVISION
1 GENERAL
2 OUTLINE OF THE REVISION
3 DETAILED DESCRIPTION
3.1 Section INTRO
3.2 Section SB INCORPORATED
3.3 Section 05.10.00
3.4 Section 05.20.00
3.5 Section 05.52.00
TECHNICAL PUBLICATIONS
1 THE DOCUMENTATION
2 OPERATION DOCUMENTS
3 MAINTENANCE DOCUMENTS
4 IDENTIFICATION DOCUMENTS
5 SPECIAL DOCUMENTS
6 VENDOR'S DOCUMENTS
GLOSSARY
STRUCTURE OF THE MSM
1 GENERAL STRUCTURE OF THE MSM
2 BREAKDOWN OF THE MSM
2.1 Identification of the DUs
2.2 Task codes
2.3 List Of Effective Document Units (LOEDU)
3 CLASSIFICATION OF INFORMATION
UPDATE OF THE MSM
1 REVISION OF THE MSM
2 UPDATE OF THE MSM
2.1 Update procedure
4 EFFECTIVITY
AS 532 SC
TABLE OF CONTENTS
2021.07.28 Page 1
MSM
TITLE
BREAKDOWN OF THE MSM
1 PURPOSE OF THE MSM
2 CHANGES TO THE MSM
3 HELICOPTER MAINTENANCE
4 TYPES OF MAINTENANCE
5 DEFINITION OF THE MAINTENANCE MODES
5.1 Hard time maintenance
5.2 On-Condition maintenance
5.3 Condition monitoring maintenance
6 EFFECTIVITY - RESPONSIBILITY
7 MAINTENANCE INTERVAL
7.1 Daily checks
AS 532 SC
TABLE OF CONTENTS
2021.07.28 Page 2
MSM
TITLE
5.2 Calendar time
5.2.1 Start date for airframe aging
5.3 Cycles
6.3.2 Components subject to Time Between Overhauls (TBO), Operating Time Limit (OTL), On-Condition
maintenance (OC)
7 RECORDING
8 MAINTENANCE CODES (MC)
9 CONTENT OF A TASK
OPTIONAL
1 COMPATIBILITY / INCOMPATIBILITY
2 TABLE OF APPROVED OPTIONAL INSTALLATIONS
3 EXPLANATIONS CONCERNING INCOMPATIBILITY
SB INCORPORATED
AS 532 SC
TABLE OF CONTENTS
2021.07.28 Page 3
MSM
1 GENERAL
- Check that the content of the sections is in accordance with the List Of Effective Document Units
(LOEDU).
- Return the acknowledgment card.
3 DETAILED DESCRIPTION
3.1 Section INTRO
- SB INCORPORATED Modified
AS 532 SC
HIGHLIGHTS
2021.07.28 Page 1
MSM
- 52/11/01/000/000/000 9000 FH
Side plug door - Middle fitting
New task integrated
AS 532 SC
HIGHLIGHTS
2021.07.28 Page 2
MSM
- 63/20/00/000/000/190 50 FH
Rotor brake flange attachment
New task integrated
- 63/20/00/000/000/200 50 FH
Rotor brake flange attachment
Description modified
Limit modified
- 63/20/00/000/000/210 50 FH
Rotor brake flange attachment
Limit modified
- 63/20/00/000/000/220 50 FH
Rotor brake flange attachment
Description modified
Limit modified
63-23 ROTOR BRAKE
- 63/23/00/000/000/002 50 FH
Rotor brake - Brake flange
Task deleted
AS 532 SC
HIGHLIGHTS
2021.07.28 Page 3
MSM
TECHNICAL PUBLICATIONS
1 THE DOCUMENTATION
The technical documentation intended for operators is mainly broken down into five groups:
2 OPERATION DOCUMENTS
- The Master Servicing Manual (MSM) is intended particularly for those responsible for helicopter
maintenance. It specifies the maintenance limits.
- The Airworthiness Limitations Section (ALS) is intended for those responsible for helicopter
maintenance. It defines the mandatory limits and checks.
- The flight manual (PMV) is intended for flight crews. It specifies the limits, standard and emergency
procedures and helicopter performance data.
- The Master Minimum Equipment List (MMEL) specifies the minimum list of equipment necessary for
flight.
3 MAINTENANCE DOCUMENTS
- The maintenance manual (MET) specifies the maintenance procedures necessary to service the
helicopter.
- The description and operation manual (MDF) explains the description and the operation of the
systems.
- The mechanical repair manual (MRM) contains the work cards for the repair or replacement of parts or
mechanical assemblies.
- The structural repair manual (MRS) contains the pages dealing with the identification of materials
and protection.
- The standard practices manual (MTC) combines all the general know-how and knowledge necessary
regarding implementation, maintenance, checks, standard repairs and technical and safety instructions
and storage conditions.
- The wiring diagram manual (MCS) combines all the helicopter wiring diagrams.
- The Special Index Modification (SIM) lists the applicable modifications and their corresponding SBs
where applicable.
4 IDENTIFICATION DOCUMENTS
- The Illustrated Parts Catalog (IPC) contains all the spare parts necessary to ensure continued
serviceability of the helicopter.
- The illustrated tools catalog (ICO) contains all the tools necessary to ensure continued serviceability
of the helicopter.
5 SPECIAL DOCUMENTS
- Service Bulletins (SB), Alert Service Bulletins (ASB) and Emergency Alert Service Bulletins
(EASB) are intended to inform the operators of instructions introduced following new events (incidents,
modifications, etc.). These documents supplement the helicopter documents and are incorporated
in the latter by updates if necessary.
- Information Notices (IN) and Safety Information Notices (SIN) are documents issued for information.
Their purpose is to remind operators of existing maintenance procedures, or to inform them of changes
validated by Airbus Helicopters and undergoing introduction.
6 VENDOR'S DOCUMENTS
- This documentation comprises the following vendor's manuals: Service Bulletins Vendors (SBV),
Engine Maintenance Manual (EMM) and Component Maintenance Manual (CMM).
AS 532 SC
TECHNICAL PUBLICATIONS
2018.08.17 Page 1
MSM
AS 532 SC
TECHNICAL PUBLICATIONS
2018.08.17 Page 2
MSM
GLOSSARY
AS 532 SC
GLOSSARY
2021.07.28 Page 1
MSM
AS 532 SC
GLOSSARY
2021.07.28 Page 2
MSM
WGH: WeiGHing
Y: Year
AS 532 SC
GLOSSARY
2021.07.28 Page 3
MSM
- The title of the manual at the top right hand side of the page,
- The effectivity (helicopter type and version) marked at the bottom left hand side of the page,
- The date code of the DU at the bottom left hand side of the page below the effectivity
(format: year.month.day),
- The number of the section or title of the DU at the bottom right hand side of the page,
- The page number at the bottom right hand side of the page,
- The ATA number at the bottom of the page only for the sections 05-10-00, 05-20-00,
05-50-00 and 05-52-00.
The end of each Document Unit is identified by " End of the Document Unit" on the last page.
AS 532 SC
STRUCTURE OF THE MSM
2014.01.09 Page 1
MSM
The first four digits (22/30/10/601/000/010) correspond to the ATA chapter/section breakdown.
The fifth and sixth digit (22/30/10/601/000/010) are used to subdivide an ATA chapter/section
comprising several subjects into individual subjects.
The seventh to fifteenth digit (22/30/10/601/000/010) according to the section of the MSM are used
to identify the tasks per ATA chapter/section/subject.
- The Document Unit (DU): this column specifies the number of the section, ATA number or
the title of the DU (example: 05-20-00 ATA 36).
- The type: this column is coded with the letter "R" if the DU is revised, "D" if the DU is deleted,
"N" if the DU is new, or has no code for DUs which are unchanged.
- The date: this column indicates the DU date code.
3 CLASSIFICATION OF INFORMATION
The DUs in sections 05-10-00, 05-20-00, 05-50-00 and 05-52-00 are classed in increasing order according
to ATA 100 numbering.
The tasks comprising the DUs in sections 05-20-00 and 05-52-00 are arranged in the following order:
perform once tasks at the start of the DU, followed by periodic tasks.
End of the Document Unit
AS 532 SC
STRUCTURE OF THE MSM
2014.01.09 Page 2
MSM
- LOEDU,
- Table of contents,
- Highlights of the revision.
AS 532 SC
UPDATE OF THE MSM
2015.04.16 Page 1
MSM
The Basic Manual Revisions (on a white background) are completely separate from the Customer
Complement Revisions (issued on a green background).
4 EFFECTIVITY
The operator must check the effectivity of the MSM used (correctly updated) for the helicopter concerned.
The effectivity (helicopter type and version) is indicated on the cover page and is repeated at the bottom of
each page comprising the MSM DUs.
End of the Document Unit
AS 532 SC
UPDATE OF THE MSM
2015.04.16 Page 2
MSM
3 HELICOPTER MAINTENANCE
Helicopter maintenance consists in applying all the operations specified in the various sections of the MSM.
It must be performed by personnel with the required qualifications.
Maintenance includes the monitoring, servicing and reconditioning of a helicopter's components, as specified
in the various manuals, taking into account the information that the manufacturer makes known to the operator
via Alert Service Bulletins, Service Bulletins, Safety Information Notice, Information Notice etc.
4 TYPES OF MAINTENANCE
Preventive Maintenance:
Preventive maintenance consists of all the scheduled, and generally repetitive, operations to check and
maintain a given operating condition.
Corrective Maintenance:
Corrective maintenance consists of all the operations that are performed after detection of a fault or failure in
order to re-establish the initial operating condition.
Remedial Maintenance:
Remedial maintenance consists of all the operations initiated to permanently correct a failure and to partially
or wholly eliminate the preventive and corrective maintenance.
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 1
MSM
The modes (defined below) differ mainly in how the replacement (or repair) of a component with a serviceable
component is initiated. With the first two modes, the aim is to replace (or repair) the component before it fails,
whereas in the third mode, to replace it after it fails.
NOTE
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 2
MSM
In both cases, the component is kept in service until the next inspection. The component must
be removed from service when it reaches the criterion for removal, or made serviceable again as
per the instructions given in the documentation.
Consequently, the removal of such items cannot be programmed. The type of intervention depends
on the result of the inspections.
The visual inspection is aimed at the overall external appearance of the component (no distortion,
failure, cracks, scratches, signs of heating or wear, etc.), which would degrade its original condition.
STANDING INSTRUCTIONS RELATIVE TO CONDITION: Surface deterioration and deterioration to
protection and paint on all helicopter components must be examined and treated without delay in
accordance with the applicable instructions (criteria, then reworking).
6 EFFECTIVITY - RESPONSIBILITY
The limits assigned to the component part numbers listed in the MSM are applicable to material:
- acquired directly from Airbus Helicopters or through the Airbus Helicopters subsidiaries or distribution
network,
- purchased from the equipment vendors listed in our spare part catalogs, either directly or through
their own distribution network.
In all cases, the manufacturing source is specified in the "airworthiness document" (JAA form one, EASA
Form One or equivalent).
Airbus Helicopters will not carry out repairs on components which were procured other than through the
Airbus Helicopters distribution network.
7 MAINTENANCE INTERVAL
7.1 Daily checks
The purpose of the daily checks is to ensure the serviceability of the aircraft for the flights of the day.
The daily checks are broken down as follows:
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 3
MSM
Acceptance of an aircraft by the pilot and/or when a modification is embodied on the aircraft:
The mechanic or the person in charge of the maintenance engineering must inform the pilot on a
routine basis of:
- any modification to the definition that has been embodied on the aircraft,
- any possible change in the limit interval of the component modified.
7.1.1 Cold weather and very cold weather routine check
According to the lowest temperatures reached, a supplementary program is defined in
the maintenance manual (MET).
7.1.2 Check of Optional Installations
The daily checks applicable to optional systems are also specified in the Flight Manual. The
detailed program is also given in the maintenance manual (MET) Work Card 05.21.00.604.
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 4
MSM
The major inspection, called “G” inspection, must be carried out every 7500 flight hours.
For helicopters which have not logged 7500 flight hours when the 12-year (144-month) limit is
reached, one of the following 2 options can be chosen:
OPTION A:
- At the 12-year limit: carry out major inspection “G” (7500 FH) plus all the maintenance tasks with
a 12-year limit, except those marked: “CAUTION: aging task” in the “description” column.
OPTION B:
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 5
MSM
- At the 12-year limit: carry out all the maintenance tasks with a 12-year limit, including those
marked: “CAUTION: aging task” in the “description” column.
- At the 15-year limit: carry out major inspection “G” (7500 FH) plus all the maintenance tasks
with a 15-year limit.
AS 532 SC
BREAKDOWN OF THE MSM
2017.07.10 Page 6
MSM
3 IN-SERVICE MONITORING
3.1 Airframe monitoring
The in-service monitoring of the airframe must be recorded in the helicopter logbook.
- Manufacturer Part Number (MP/N): This is the identification number of the component marked
on the identification plate or directly on the component.
AS 532 SC
USE OF THE MSM
2021.07.28 Page 1
MSM
- Airbus Helicopters Part Number (P/N):This is the Airbus Helicopters part number which
is associated with the manufacturer’s part number (MP/N) for components which are not
manufactured by Airbus Helicopters.
The part numbers of the components (parts or assemblies) which are given in the MSM are the
manufacturer’s part numbers (MP/N).
In the case of components which are not manufactured by Airbus Helicopters, the MP/N is followed
by the associated P/N (in brackets).
Example:
In some cases the MP/N is not specified, in this case it is replaced by a hyphen.
- flight hours,
- calendar time,
- cycles,
- number of operations (for certain components).
AS 532 SC
USE OF THE MSM
2021.07.28 Page 2
MSM
- in Years (Y),
- in Months (M),
- in Days (D),
- Before the First Flight of the day (BFF),
- Turn Around check (TA),
- After the Last Flight of the day (ALF),
- with the date marked on the equipment label (ED: Expiry Date).
5.2.1 Start date for airframe aging
The start date to be taken into account for airframe aging is the date marked on the
helicopter identification plate.
5.2.2 Start date for component aging
AS 532 SC
USE OF THE MSM
2021.07.28 Page 3
MSM
NOTE
- new equipments,
- not new mechanical assemblies and their constituants after
accomplishment of an overhaul.
In this case, the MSM Tasks do not contains any specification.
Exception:
AS 532 SC
USE OF THE MSM
2021.07.28 Page 4
MSM
The maintenance plan start date to be taken into account for the
aging of components and dynamic assemblies is the date marked
on the maintenance plate or, if there is none, on the helicopter
identification plate:
Example: Maintenance plate
Exception:
AS 532 SC
USE OF THE MSM
2021.07.28 Page 5
MSM
5.3 Cycles
According to the component, the cycles can be expressed either as:
AS 532 SC
USE OF THE MSM
2021.07.28 Page 6
MSM
- Periodically: the maintenance operation must be performed at the latest when the indicated
limit is reached.
NOTE
or
AS 532 SC
USE OF THE MSM
2021.07.28 Page 7
MSM
- Once only: the maintenance operation must be performed once only, when the indicated limit is
reached.
It must not be performed before the limit is reached.
These maintenance operations are identified by a dotted line around the task and by code
PO (Perform Once) in front of the limit value.
These operations can be performed either:
- After installation of a component removed from the same helicopter,
- After the introduction to service of a new, overhauled or repaired component,
- After installation of a component originating from another helicopter,
- Each time after the component is installed.
The start of the maintenance operation is specified in each task concerned.
Example:
Section 05-10-00
A servocontrol performs 2000 FH over a period of 20 Y (TSM). The first limit reached by the
servocontrol is therefore 20 Y; it must be removed for overhaul (TBO) and returned to service for
another period.
After overhaul, the servocontrol is installed on a helicopter and then performs 3000 FH in 15 Y.The
first limit reached by the servocontrol is therefore 3000 FH. It must therefore be removed for another
overhaul (TBO).
Example 2:
AS 532 SC
USE OF THE MSM
2021.07.28 Page 8
MSM
Section 05-20-00
The maintenance operation must be performed once at 5 Y and once at 8 Y after manufacture.
- Salt-laden atmosphere:
. Ship-based or,
. Based for more than 50% of its time less than 1 km from the coast or,
. Spending more than 50% of its time in offshore flight at low altitude (below 1,000 feet).
Ship-based Helicopters are subject to specific monitoring in calendar time. This close monitoring
is identified in the maintenance task by the "note": "Helicopter based aboard a ship".
- Cold weather:
Helicopters operating in the following conditions: in actual or forecast snow or ice conditions at
outside air temperatures above - 30˚C (- 22°F).
The scheduled maintenance relating to these operating conditions is covered with all the MSM tasks.
These operating conditions require not only the operations specified in the MSM and standard
maintenance operations, but also the preventive measures recommended in MET work card
AS 532 SC
USE OF THE MSM
2021.07.28 Page 9
MSM
05.55.00.301. Since the interval is not specified, the operator must reapply the measures according
to his own experience in the corresponding conditions.
X is the limit value for performing the maintenance operation and Y is the margin value
added to the limit value.
After using the first margin value (partially or completely), the next maintenance operation
is to be performed again within the X+Y interval, that is to say before the next maximum
limit value.
AS 532 SC
USE OF THE MSM
2021.07.28 Page 10
MSM
- the versions "x" and "y" are listed in the above table, transfer of
components from any other version or any other type of aircraft is
prohibited (example: SA 330 or MOX-specific components from a PUMA
version, version-specific KUH [P] or GTV components),
- the part number of the component to be transferred is listed both in section
05-10-00 of version "x" and in section 05-10-00 of version "y",
- no provisional limitation of the component to be transferred is assigned in
the MSM of version "x" or in the MSM of version "y",
- the time interval of the components subject to TBO and OTL are identical
both in the MSM of version "x" and in the MSM of version "y",
- MTC Work Card 20.08.05.104 is applied during the transfer.
SPECIAL CASE
The following elements: ENGINE-TO-MGB COUPLING SHAFT, IGB
ASSEMBLY, MAIN SERVOCONTROL, TAIL SERVOCONTROL are only
authorized to be transferred inside the following group of versions :
- 332 B, B1, F1, M, M1, 532 AC, AL, SC, UE, UL,
- 532 A2, U2,
- 332 C, C1, L, L1,
- 332 L2.
AS 532 SC
USE OF THE MSM
2021.07.28 Page 11
MSM
7 RECORDING
In all cases record the transfer information and calculation on the equipment log card of the component
concerned.
An individual log card must be drawn up if the component has been monitored via the log card of its higher
assembly.
- LUBrication/SerViCing (LUB/SVC)
This includes work such as routine lubrication and servicing, filling/topping-up of oils, fluids, liquids
and checking of pressures.
AS 532 SC
USE OF THE MSM
2021.07.28 Page 12
MSM
A special detailed inspection is an inspection to detect and assess deterioration or incorrect operation
of a component or assembly. This inspection may require a specific process such as dye penetrant
inspection, radiography, etc.
- CLeaNing (CLN)
To remove dirt and/or foreign bodies from a system or surface. Cleaning may require removal of the
component, such as for a filter for example.
- DiScard (DS)
A component is withdrawn from service at a specified limit. Discarding normally applies to parts such as
cartridges, containers, cylinders, batteries, etc.
- ReStoration (RS)
This work involves restoring a component to a specific standard. Restoration can vary from cleaning
or replacing detail parts to a complete overhaul.
- WeiGHing (WGH)
The aim is to remove the equipment in order to weigh it using scales, to check its integrity and to make
sure that there are no losses.
- DRaiNing (DRN)
Draining/replenishing consists in replacing all the fluid, liquid, oil or fuel in a component.
AS 532 SC
USE OF THE MSM
2021.07.28 Page 13
MSM
- RiggInG (RIG)
Rigging consists in adjusting a control channel or a set of components which must have an operating
range in the correct direction during operation.
9 CONTENT OF A TASK
Example section 05-10-00:
End of section
AS 532 SC
USE OF THE MSM
2021.07.28 Page 14
MSM
AS 532 SC
USE OF THE MSM
2021.07.28 Page 15
MSM
OPTIONAL
1 COMPATIBILITY / INCOMPATIBILITY
A helicopter can be equipped with various optional items. There can be incompatibilities between certain
optional installations which can appear at two levels:
At operational level:
- In this case, incompatibilities between optional items are specified in the Flight Manual.
- Either the helicopter can be equipped with two optional installations but not at the same time: there is
an installation incompatibility.
- Or the two installations can be installed together on the condition that one of them is modified: this is
called conditional compatibility.
The following table lists all the approved optional installations with their incompatibilities, conditional
compatibilities, or effects on operation, as specified in a Flight Manual Supplement.
INSTALLATION CONDITIONAL
ITEM DESCRIPTION INCOMPATIBILITY INSTALLATION
WITH INCOMPATIBILITY WITH
AS 532 SC
OPTIONAL
2015.10.15 Page 1
MSM
INSTALLATION CONDITIONAL
ITEM DESCRIPTION INCOMPATIBILITY INSTALLATION
WITH INCOMPATIBILITY WITH
9 Ice-Trap System
31.50.51.52.53.55.58.60
36 Full De-Icing Installation 34.37
(1)
31.50.51.52.53.55.58.60
37 Light De-Icing Kit 36
(1)
AS 532 SC
OPTIONAL
2015.10.15 Page 2
MSM
INSTALLATION CONDITIONAL
ITEM DESCRIPTION INCOMPATIBILITY INSTALLATION
WITH INCOMPATIBILITY WITH
AS 532 SC
OPTIONAL
2015.10.15 Page 3
MSM
INSTALLATION CONDITIONAL
ITEM DESCRIPTION INCOMPATIBILITY INSTALLATION
WITH INCOMPATIBILITY WITH
48.49.50.53.56.57.
54 Air Ambulance Installation 74.75.76.77 (6)
61.62.78
36.37 (1)
55 Fixed Arm Variable Speed Hoist 73.81.82
49.50.51.53.57.61
48.49.50.53.54.57.
56 Drip Pan
61.73.77.78
48.49.54.56.61.74.
57 Airdrop System 75.76.77.78.79,80. 50.51.53.55.62
81.82.83
59 Incandescent Flares - -
39.40.41 (3)
49.54.56.57.74.75.
61 600-Liter Cabin Fuel Tank 55.76.77
76.77.78
74.75 (5)
50.53.72.73.75.81. 54 (6)
62 Abseiling Installation
82 51.57
70 Reinforced Soundproofing 71
AS 532 SC
OPTIONAL
2015.10.15 Page 4
MSM
INSTALLATION CONDITIONAL
ITEM DESCRIPTION INCOMPATIBILITY INSTALLATION
WITH INCOMPATIBILITY WITH
49.50.53.56.57.75.
74 24-Utility Seats Installation 76.77.78.79.80.81. 48.54.61 (5)
82
49.50.53.56.57.74.
75 18-Crashworthy Utility Seats Installation 76.77.78.79.80.81. 48.54.61 (5)
82
49.50.53.56.57.74.
76.77 20 and 19 Comfortable Seats Installation 48.54.61 (4)
75.78.80.81.82
49.50.53.56.57.74.
78 18-Comfortable Seats + Toilet Installation 48.54.61 (4)
75.76.77.81.82
48.49.50.53.54.55.
81 10-12 VIP Seat Installation 56.57.61.62.74.75.
76.77.78.79.82
AS 532 SC
OPTIONAL
2015.10.15 Page 5
MSM
31 The skis installation can be used providing that the landing gear is not retracted (inhibiting
handle) nor semi-retracted (“kneeling” position).
50.51.55 These installations MUST NOT be used during flights in icing conditions.
54.74.75.76.77 The partial use of these installations is possible with the ferry fuel tanks, providing it is
approved by the authorities concerned.
28 The installation of lige rafts in the sponsons requires the installation of the reduced emergency
floatation gear installation (26).
73 Compatible with the life raft installation only if the aft panel can be jettisoned.
61.55 These optional items can both be installed and used together only if the modification kit
332P67-9889-00 has been installed. (Shears relocated, a guard installed on the corner of the
fuel tank and the control grip mount modified).
AS 532 SC
OPTIONAL
2015.10.15 Page 6
MSM
SB INCORPORATED
Airbus Helicopters is required to issue Service Bulletins (ASB/SB) subsequent to new events (incidents, etc).
The information contained in the SBs is incorporated in the MSM if, and only if:
The SB contains new periodic checks, or modifies the existing MSM limitations.
05.00.24 Main rotor blades leading edge end and blade 62-10 - -
tip fairing check
05.00.39 Tail boom - Check of the skin at frame 9000 or 53-10 - 2006.04.07
9900
05.00.09 Addition of a calendar time limit for the dynamic 60-00 - 2007.04.30
assemblies which are maintained: -According
to “On-Condition” procedures. - According to
their TBO
AS 532 SC
SB INCORPORATED
2021.07.28 Page 1
MSM
AS 532 SC
SB INCORPORATED
2021.07.28 Page 2
MSM
AS 532 SC
SB INCORPORATED
2021.07.28 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
21/52/00/402/000/000
Turbo-fan cooling unit
MET 21.52.00.402 3202A0101 (-) TBO A 1200 FH X A 120 FH
3202A0201 (-)
3202B0101 (-)
3202B0201 (-)
AS 532 SC
05-10-00
2021.07.28 ATA 21 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
22/30/00/000/000/005
Autopilot hydraulic unit - Distributor
010-60666 (-) TBO A 6000 FH X A 300 FH
A84122-1 (704A44820013)
// 15 Y X A 180 D
22/30/00/000/000/020
Autopilot hydraulic unit - Trim electrovalve
MET 22.30.10.403 30010 (702A10007521) TBO A 6000 FH X A 300 FH
67-770-1 (702A10007522)
67-770-2 (702A10007523)
702A10007520 (-)
22/30/00/000/000/021
Autopilot hydraulic unit - Servodistributor
30550-401 (704A44810013) TBO A 6000 FH X A 300 FH
30550-501 (704A44810013)
22/30/00/000/000/022
Autopilot hydraulic unit - Servodistributor
MET 22.30.10.403 A21495 (704A44810016) TBO A 7200 FH X A 300 FH
A84121 (704A44810016)
A84121-1 (704A44810016)
// 15 Y X A 180 D
22/30/00/000/000/040
Autopilot hydraulic unit
702A10-0092-11 (-) TBO A 3000 FH X A 150 FH
22/30/10/401/000/000
Hydraulic unit - Filter - Filter element
MET 22.30.10.401 CG0140093411N00 (-) OTL A 3000 FH X A 300 FH
This filter cannot be cleaned. It must be replaced if clogging is detected.
22/30/10/402/000/000
Autopilot hydraulic unit
MET 22.30.10.402 6784063200 (-) TBO A 3000 FH X A 300 FH
6784063300 (-)
6784063400 (-)
22/30/10/402/000/010
Autopilot hydraulic unit
MET 22.30.10.402 702A10-0095-00 (-) TBO A 3000 FH X A 150 FH
AS 532 SC
05-10-00
2021.07.28 ATA 22 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 23-COMMUNICATIONS
23/71/01/510/000/010
CVFDR Recorder - Without HUMS, EUROHUMS, EUROARMS option
980-6021-032 (704A45381025) OC
Recorders AR-602C fitted with the DUKANE DK100 or DK120 or DATASONIC ELP-362D acoustic beacon.
23/71/01/510/000/020
CVFDR Recorder - Without HUMS, EUROHUMS, EUROARMS option
D51521-010-112 (704A45381021) OC
Recorders Type 2000 fitted with the DUKANE DK100 or DK120 or DATASONIC ELP-362D acoustic beacon.
23/71/01/510/401/000
Cockpit voice recorder
MET 23.71.01.401 93A100-31 (704A45381002) TBO A 4000 FH X A 300 FH
93A100-80 (704A45381000)
A100.
AS 532 SC
05-10-00
2018.08.17 ATA 23 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
24/20/00/000/000/010
30-40 kVA alternator
MET 24.21.00.401 30030-1 (704A46220028) TBO A 3000 FH X A 300 FH
30030-2 (704A46220035)
// 10 Y X TSM 180 D
AUXILEC.
TSM or Overhaul.
24/20/00/000/000/020
20 kVA alternator
MET 24.21.00.401 86002-012 (704A46220018) TBO A 2000 FH X A 0A
86002-112 (704A46220032)
AIR EQUIPMENT.
24/20/00/000/000/030
40 kVA alternator
MET 24.21.00.401 86003-020 (704A46220016) TBO A 5000 FH X A 0A
86003-021 (704A46220022)
AIR EQUIPMENT.
These alternators must not be installed on MGBs lubricated with O-155 mineral oil.
24/20/00/000/000/070
20 kVA alternator
MET 24.21.00.401 AL9472V01 (704A46220031) TBO A 3000 FH X A 0A
AL9472V01-1 (704A46220033)
ARTUS.
24/20/00/000/000/080
30 kVA alternator
MET 24.21.00.401 AL0672V01 (704A46220030) TBO A 3000 FH X A 0A
AL0672V01-1 (704A46220034)
ARTUS.
AS 532 SC
05-10-00
2015.04.16 ATA 24 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
24-31 BATTERY
24/31/00/000/000/010
43 Ah battery
40208-1 (704A46130020) OC
40208-5 (704A46130038)
40408 (704A46130034)
24/31/00/000/000/110
40 Ah battery
60061200401 (704A46130048) OC
60061200402 (704A46130047)
24/31/00/000/000/210
Standby battery
BTS89A (704A46130042) OC
EE0005 (704A46130021)
EE0005-01 (704A46130026)
EE0005-011 (704A46130031)
EE0005-0111 (704A46130032)
24/31/00/000/000/240
Standby battery
BTS03A (704A46130053) OC
AS 532 SC
05-10-00
2015.04.16 ATA 24 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 25-EQUIPMENTS/FURNISHINGS
25-00 EQUIPMENTS/FURNISHINGS
25/00/00/000/000/000
Belt straps - Harness - Medical installation straps
ALL MP/N (-) OC
Pilot, copilot, passenger and operator seat belt and harness straps - Medical installation straps.
For seat belts and harnesses fitted with buckles manufactured by ANJOU refer to the 04-10-00 chapter.
25-10 COCKPIT
25/10/00/000/000/010
Pilot's and copilot's seat shock absorbers
2510102900-01 (-) OTL A 5Y X A 0A
2510102900-02 (-)
VIBRACHOC
25/10/00/000/000/020
Third crew member's seat shock absorber
2510107900 (-) OTL A 5Y X A 0A
2510107901 (-)
VIBRACHOC
Return the equipment to an approved repair station for overhaul and replacement of the unequipped bottle.
25/62/00/401/000/040
Aft cylinder
MET 25.62.00.401 200740-0 (-) OTL A 15 Y X TSM 0A
200740-1 (-)
200740-2 (704A42693012)
Return the equipment to an approved repair station for overhaul and replacement of the unequipped bottle.
25/62/00/403/000/000
Forward float
158820-0 (-) OTL A 10 Y X TSM 180 D
158820-1 (-)
158820-2 (-)
158820-3 (-)
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/62/01/403/000/000
Aft left float
MET 25.62.01.403 207035-0 (-) OTL A 10 Y X TSM 180 D
207035-1 (-)
207035-2 (-)
You can apply for an extension by returning the equipment in question to the manufacturer for examination.
25/62/01/403/000/030
Aft right float
MET 25.62.01.403 207036-0 (-) OTL A 10 Y X TSM 180 D
207036-1 (-)
207036-2 (-)
You can apply for an extension by returning the equipment in question to the manufacturer for examination.
25/64/00/000/000/021
Hydraulic hoist 50 m / 600 lbs - Cable
CMM 25.62.21 709070 (N6700370121) OTL A 2 Y X TSI 0A
709070-100 (NR100370415)
CMM 25.64.96 // 7 Y X TSM 0A
// 500 HC X A 0A
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
TSM in original package.
25/64/00/000/000/080
Hydraulic hoist 50 m / 600 lbs, constant speed - Hook D'Lok
712772-200 (704A41816076) TBO A 10 Y X A 0A
// 2000 HC X A 0A
25/64/00/402/000/000
Hydraulic hoist 50 m / 600 lbs
76360-200 (704A41815057) TBO A 4Y X A 0A
76360-210-00 (704A41815058)
76360-210-01 (704A41815059)
// 1000 HC X A 0A
76360-210-0D (704A41815115)
76360-210-1D (704A41815114)
76363-200-A (-)
76363-300 (-)
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/64/00/403/000/005
Hoist system - Pyrotechnic cartridge
20CF4D (N6714400100) OTL A 3Y X TSI 0A
// 5Y X TSM 0A
TSM in original package.
25/64/01/401/000/000
Hydraulic hoist 75 m / 600 lbs, variable speed
76365-230 (704A41815060) TBO A 4Y X A 146 D
76368-200 (704A41815061)
76368-240 (704A41815062)
// 2000 HC X A 200 HC
76368-240-D (704A41815083)
25/64/01/401/000/004
Hydraulic hoist 75 m / 600 lbs, variable speed - Cable
710696 (-) OTL A 4 Y X TSI 0A
710696-100 (-)
// 9 Y X TSM 0A
// 500 HC X A 0A
Normal climatic conditions
TSM in original package.
25/64/01/401/000/005
Hydraulic hoist 75 m / 600 lbs, variable speed - Cable
710696 (-) OTL A 2 Y X TSI 0A
710696-100 (-)
// 7 Y X TSM 0A
// 500 HC X A 0A
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
TSM in original package.
25/64/02/000/000/000
Electric hoist 28 VDC 34 m / 300 lbs, constant speed
BL16600-120 (704A41815022) TBO A 5Y X A 180 D
BL16600-120-1 (-)
BL16600-180 (704A41815037)
// 2000 HC X A 200 HC
BL16600-90 (704A41815019)
25/64/02/000/000/012
Electric hoist 28 VDC 40 m / 300 lbs, constant speed
76370-130 (704A41815035) TBO A 4Y X A 146 D
76370-140-D (704A41815085)
// 1500 HC X A 150 HC
25/64/02/000/000/020
Electric hoist 28 VDC 34 m / 300 lbs, constant speed - Pyrotechnic cartridge
BL7811 (-) OTL A 3Y X TSI 0A
Y1265-3-1 (-)
// 5Y X TSM 0A
TSM in original package.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/64/02/000/000/035
Electric hoist 28 VDC 34 m / 300 lbs, constant speed - Cable
BL7505 (-) OTL A 4 Y X TSI 0A
// 9 Y X TSM 0A
// 500 HC X A 0A
Normal climatic conditions
TSM in original package.
25/64/02/000/000/050
Electric hoist 28 VDC 34 m / 300 lbs, constant speed - Cable
BL7505 (-) OTL A 2 Y X TSI 0A
// 7 Y X TSM 0A
// 500 HC X A 0A
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
TSM in original package.
25/64/02/000/000/055
Electric hoist 28 VDC 40 m / 300 lbs, constant speed - Cable
710656 (-) OTL A 4 Y X TSI 0A
710656-100 (-)
// 9 Y X TSM 0A
// 500 HC X A 0A
Normal climatic conditions
TSM in original package.
25/64/02/000/000/060
Electric hoist 28 VDC 40 m / 300 lbs, constant speed - Cable
710656 (-) OTL A 2 Y X TSI 0A
710656-100 (-)
// 7 Y X TSM 0A
// 500 HC X A 0A
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
TSM in original package.
25/64/02/000/000/540
Electric hoist 115 VAC 90 m / 600 lbs, variable speed
BL29900-59 (704A41815089) TBO A 10 Y X TSM 180 D
// 2000 HC X A 200 HC
TSM or Overhaul.
25/64/02/000/000/550
Electric hoist 115 VAC 90 m / 600 lbs, variable speed - Pyrotechnical cartridge
BL11140-1 (704A38710032) OTL A 3Y X TSI 0A
// 9Y X TSM 0A
TSM in original package.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 4
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/64/02/000/000/560
Electric hoist 115 VAC 90 m / 600 lbs, variable speed - Cable
BL-10653-3 (-) OTL A 2 Y X TSI 0A
// 7 Y X TSM 0A
// 500 HC X A 0A
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
TSM in original package.
25/64/02/000/000/570
Electric hoist 115 VAC 90 m / 600 lbs, variable speed - Cable
BL-10653-3 (-) OTL A 4 Y X TSI 0A
// 9 Y X TSM 0A
// 500 HC X A 0A
Normal climatic conditions
TSM in original package.
25/66/00/000/000/060
Deployment mechanism - Battery
CMM 25.65.98 00-23-1099 (704A46132002) OTL A 2Y X TSI 0A
// 5Y X TSM 0A
BCAL CPT 606.
TSM in original package.
25/66/00/000/000/072
Emergency locator transmitter - Battery pack
CMM 25.65.97 606-180-001 (NR017700738) OTL A A ED X A 0A
BCAL CPT 606.
25/66/00/000/000/080
Pyrotechnical cartridge
CMM 25.65.98 BC85-070 (NR663700001) OTL A 1Y X TSI 0A
// 5Y X TSM 0A
BCAL CPT 606.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 5
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/66/00/000/000/110
Battery
120093-1 (704A46132000) OC
135417-1 (704A46132000)
25/66/00/000/000/115
Battery rechargeable
CMM 25.60.03 10114-1 (-) OTL A 4Y X TSM 146 D
Fitted on assemblies: MP/N 135417-1 or MP/N 120093-1.
25/66/00/000/000/120
Battery pack
CMM 25.60.03 126568-1 (-) OTL A 4Y X A 0A
126568-3 (704A36132006)
// 1 OPHX A 0A
LEIGH CPI 113.
1 OPH = 1 hour of operation except for testing..
25/66/00/000/000/130
Pyrotechnical cartridge
CMM 25.60.03 11430-2 (-) OTL A 3Y X TSM 0A
6100-138959-2 (-)
25/66/00/000/000/160
Battery
GS21 (-) OTL A 2Y X TSM 0A
EBC 302HM.
25/66/00/000/000/200
Battery pack
CMM 25.69.15 JE2-1978-3 (N6742450122) OTL A A ED X A 0A
JE2-1978-3NG (NR003100026)
// 1 OPHX A 0A
JOLLIET JE2-1978-0/JE2-1978-0-NG.
1 OPH = 1 hour of operation, except for testing.
25/66/00/000/000/240
Battery pack
CMM 25.61.02 ELT90A2560102001 (-) OTL A 4 Y X TSM 0A
// 1 OPHX A 0A
ELT 96-406 SOCATA.
1 OPH = 1 hour of operation, except for testing.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 6
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/66/00/000/000/245
Portable lamp - Battery
TYPE LR6 (-) OTL A 1Y X A 36 D
To be replaced every year from the date of installation marked on the portable lamp.
25/66/00/510/000/180
Underwater acoustic beacon
CMM 25.66.97 5845-01-3447914 (-) TBO A A ED X A 0A
DK100.
Beacon to be returned to the manufacturer.
25/66/00/510/000/190
Underwater acoustic beacon - Battery
CMM 25.69.73 810-418A (-) OTL A 2Y X TSM 0A
DUKANE 210B.
25/66/00/510/000/320
Underwater acoustic beacon - Battery pack
CMM 25.66.97 810-2007/K (-) OTL A A ED X A 0A
810-2008/K (-)
DUKANE DK120.
Beacon with "Code B" indicated on the label = Battery 810-2007/K.
Beacon with "Code C" indicated on the label = Battery 810-2008/K.
25/66/00/510/000/330
Underwater acoustic beacon - Battery
CMM 25.60.07 B362-06192-1 (-) OTL A A ED X A 0A
B362-06192-2 (-)
DATASONIC ELP-362D.
Underwater acoustic beacons with a serial number not beginning with an "S".
25/66/00/510/000/340
Underwater acoustic beacon
TBO A A ED X A 0A
DATASONIC ELP-362D.
Underwater acoustic beacons with a serial number beginning with an "S".
Underwater acoustic beacon to be returned to the manufacturer.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 7
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/66/33/000/000/010
Emergency locator transmitter - Battery pack
CMM 25.63.05 S1820516-99 (-) OTL A A ED X A 0A
// 1 OPHX A 0A
KANNAD 406-AF/AP.
1 OPH = 1 hour of operation except for testing or operation for an unknown duration.
25/69/00/000/000/050
Complete assembly
CMM 25.66.96 158500-1 (704A42691025) OTL A 7Y X TSM 180 D
Tropical and damp atmosphere
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
25/69/00/000/000/080
Battery
CMM 25.66.96 OTL A 8Y X TSM 0A
25/69/00/000/000/100
Complete left assembly
CMM 25.69.78 204359-1 (-) OTL A 10 Y X TSM 180 D
204359-2 (-)
205379-5 (704A42691026)
205379-6 (704A42691046)
Normal climatic conditions
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 8
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/69/00/000/000/110
Complete left assembly
CMM 25.69.78 204359-1 (-) OTL A 7Y X TSM 180 D
204359-2 (-)
205379-5 (704A42691026)
205379-6 (704A42691046)
Tropical and damp atmosphere
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
25/69/00/000/000/130
Complete right assembly
CMM 25.69.78 204360-1 (-) OTL A 10 Y X TSM 180 D
204360-2 (-)
205380-5 (704A42691027)
205380-6 (704A42691045)
Normal climatic conditions
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
25/69/00/000/000/140
Complete right assembly
MCM 25.69.78 204360-1 (-) OTL A 7Y X TSM 180 D
204360-2 (-)
205380-5 (704A42691027)
205380-6 (704A42691045)
Tropical and damp atmosphere
To determine whether a time extension can be granted, return the assembly in question
to the manufacturer for examination.
25/69/00/000/000/160
Cylinder
204502-0 (-) OC
217740-0 (-)
25/81/01/401/000/000
2-ton cargo hook
MET 25.81.01.401 AS21-5-5 (704A41811023) TBO A 5Y X A 180 D
AS21-5-6 (704A41811025)
// 1500 SC X A 150 SC
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 9
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
25/81/02/401/000/000
3-ton cargo hook
MET 25.81.02.401 AS21-7 (704A41811026) TBO A 5Y X A 180 D
AS21-7-1 (704A41811028)
§G // 1500 SC X A 150 SC
AS21-7-2 (704A41811031)
AS21-7-3 (704A41811032)
25/81/02/401/000/010
Swivel release unit
MET 25.81.02.401 AS21-10 (704A41811033) TBO A 5Y X A 180 D
§G // 2000 SC X A 200 SC
AS 532 SC
05-10-00
2018.08.17 ATA 25 Page 10
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
26/21/00/000/000/011
Pyrotechnical cartridge
863080-00 (704A38710040) OTL A 5Y X TSI 0A
863085-00 (704A38710041)
// 7Y X TSM 0A
TSM in original package.
26/21/00/000/000/025
Cowling fire extinguisher - Cylinder
32700014 (704A42820015) OC
860-830 (704A42820014)
862690-00 (704A42820028)
863490-00 (704A42820038)
863490-01 (704A42820046)
26/21/00/603/000/010
Double check valve
861-260 (704A34635006) OC
861-260-01 (704A34635049)
CR418Z5AERO (704A34635049)
26/22/00/000/000/050
Portable extinguisher
CMM 26.20.30 BA51015R3 (704A32810016) OTL A 10 Y X TSM 0A
BA51015R5 (704A32810021)
AS 532 SC
05-10-00
2015.10.15 ATA 26 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 28-FUEL
28-10 STORAGE
28/10/00/602/000/010
Fuel tank
ALL MP/N (-) OC
28/20/00/301/000/020
Filter - Filter element
MET 28.20.00.301 56853 (-) OTL A 2000 FH X A 200 FH
57189 (NR007702930)
57189-1 (NR007702939)
57457 (-)
57457-1 (-)
28/20/00/301/000/025
Filter
4020D25-1 (704A44620043) OC
4020P25-5 (704A44620049)
433D25-5 (704A44620029)
433D25-51 (704A44620039)
28/20/00/301/000/030
Filter - Filter element
402D25-1 (704A34620048) OTL A 1000 FH X A 100 FH
POST MOD 0725996
28/20/00/301/000/035
Filter
433D25-42 (704A44620038) OC
PRE MOD 0725996
28/20/00/301/000/045
Filter
433D25-6 (704A44620047) OC
POST MOD 0725996
28/20/00/401/000/000
Booster pump
MET 28.20.00.401 C11BA0102C (-) TBO A 1800 FH X A 0A
C11BC041 (-)
C11BD0011 (704A44510029)
C11BD0012 (704A44510034)
AS 532 SC
05-10-00
2021.07.28 ATA 28 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
28/20/00/401/000/010
Booster pump
MET 28.20.00.401 P94C16-608 (704A44510037) TBO A 2000 FH X A 0A
P99C16-610 (704A44510050)
28/20/00/405/000/000
Transfer pump
2180B (N6739302501) OC
2180B02 (N6739302502)
AS 532 SC
05-10-00
2021.07.28 ATA 28 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
29/10/00/402/000/000
Reservoir return filter - Filter element
980359 (-) OC
AC4825FUP1211 (N6703500323)
CH0913101331A00 (-)
CH0913101331N00 (-)
29/10/00/403/000/010
Hydraulic pump
MET 29.10.00.403 C24160-1 (704A44320008) TBO A 2400 FH X A 0A
MET 29.10.01.403
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
29/10/00/403/000/040
Hydraulic pump
MET 29.10.00.403 C24160026 (704A44320014) TBO A 2400 FH X A 0A
C24160042 (704A44320020)
MET 29.10.01.403
Pump installed in the right hydraulic system.
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
29/10/00/403/000/060
Hydraulic pump
MET 29.10.00.403 C24160-101 (704A44320015) TBO A 2400 FH X A 0A
C24160041 (704A44320021)
MET 29.10.01.403
C24160045 (704A44320018)
29/10/00/403/000/100
Hydraulic pump
MET 29.10.00.403 C24160026-1 (-) TBO A 2400 FH X A 0A
C24160046 (704A44320019)
MET 29.10.01.403
This pump can only be installed on MGB POST MOD 0752246.
Pump installed in the right hydraulic system.
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
AS 532 SC
05-10-00
2019.06.07 ATA 29 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
29/10/00/403/000/120
Hydraulic pump
MET 29.10.00.403 C24160045-1 (704A44320027) TBO A 3000 FH X A 300 FH
MET 29.10.01.403
This pump can only be installed on MGB POST MOD 0752246.
Pump installed in the left hydraulic system.
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
29/10/00/403/000/130
Hydraulic pump
MET 29.10.00.403 C24160046-1 (704A44320026) TBO A 3000 FH X A 300 FH
MET 29.10.01.403
This pump can only be installed on MGB POST MOD 0752246.
Pump installed in the right hydraulic system.
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
29/10/00/403/000/150
Hydraulic pump
MET 29.10.00.403 AP6VSC-PI0080 (704A44320017) TBO A 3000 FH X A 300 FH
APV6SC-PA0080 (-)
MET 29.10.01.403
These pumps can only be installed on MGB POST MOD 0722972.
WC 29.10.00.403 PRE MOD 0723817.
WC 29.10.01.403 POST MOD 0723817.
29/10/00/403/000/170
Hydraulic pump
MET 29.10.00.403 46159 (704A44310029) TBO A 3000 FH X A 300 FH
C24160041-1 (704A44320025)
MET 29.10.01.403
C24160041-100 (704A44320035)
C24160041-2 (704A44320039)
C24160041-200 (704A44320043)
C24160045-100 (704A44320037)
C24160045-2 (704A44320041)
C24160045-200 (704A44320045)
AS 532 SC
05-10-00
2019.06.07 ATA 29 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
29/10/00/403/000/180
Hydraulic pump
MET 29.10.00.403 4615001 (704A44320048) TBO A 3000 FH X A 300 FH
C24160042-1 (704A44320024)
MET 29.10.01.403
C24160042-100 (704A44320034)
C24160042-2 (704A44320040)
C24160042-200 (704A44320044)
C24160046-100 (704A44320036)
C24160046-2 (704A44320042)
C24160046-200 (704A44320046)
29/10/00/410/000/010
HP filter - Filter element
979056 (-) OC
29/20/01/407/000/000
Emergency hydraulic system electro-pump unit
A5029190 (704A44310025) OC
POST MOD 0723817.
AS 532 SC
05-10-00
2019.06.07 ATA 29 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
30/60/00/401/000/020
TRH - Collector
107550 (-) TBO A 3000 FH X A 300 FH
// 6Y X A 180 D
TSM or Overhaul.
30/60/00/402/000/000
MRH - Collector
MET 30.60.00.402 APCL105-246-20 (704A42728008) TBO A 3000 FH X A 0A
AS 532 SC
05-10-00
2015.04.16 ATA 30 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
31-20 CLOCK
31/20/00/000/000/000
Chronograph model 811B - Battery
CMM 31.21.99 MODEL811B (704A47320023) OTL A 2Y XA 0A
Battery replacement.
AS 532 SC
05-10-00
2013.01.10 ATA 31 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
32/12/00/000/000/060
Right trailing arm
C23952-4 (704A41421030) OC
C23952-5 (704A41421040)
C23952-6 (704A41421042)
32/12/00/000/000/070
Left actuator
C23949-7 (704A41421070) OC
C23953-000-1 (704A41421081)
C23953-000-2 (704A41421084)
C23953-1 (704A41421021)
C23953-103 (704A41421055)
C23953-104 (704A41421059)
C23953-105 (704A41421064)
C23953-106 (704A41421070)
C23953-107 (704A41421079)
C23953-2 (704A41421031)
C23953-3 (704A41421033)
C23953-4 (704A41421053)
32/12/00/000/000/080
Right actuator
C23950-7 (704A41421069) OC
C23954-000-1 (704A41421082)
C23954-000-2 (704A41421083)
C23954-1 (704A41421023)
C23954-103 (704A41421056)
C23954-104 (704A41421060)
C23954-105 (704A41421065)
C23954-106 (704A41421069)
C23954-107 (704A41421080)
C23954-2 (704A41421032)
C23954-3 (704A41421034)
C23954-4 (704A41421054)
32/12/00/000/000/090
Left trailing arm
MET 32.10.00.401 C23951-000 (704A41421072) OTL A20000 FH X A 0A
MET 32.10.01.401
WC 32.10.00.401 PRE MOD 0723817.
WC 32.10.01.401 POST MOD 0723817.
AS 532 SC
05-10-00
2018.08.17 ATA 32 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
32/12/00/000/000/100
Right trailing arm
MET 32.10.00.401 C23952-000 (704A41421071) OTL A20000 FH X A 0A
MET 32.10.01.401
WC 32.10.00.401 PRE MOD 0723817.
WC 32.10.01.401 POST MOD 0723817.
32/22/00/000/000/060
Landing gear leg
C23943-2 (704A41420014) OC
C23943-201 (704A41420021)
C23943-202 (704A41420028)
C23943-203 (704A41420022)
C23943-204 (704A41420030)
C23943-205 (704A41420032)
C23943-206 (704A41420034)
C23943-207 (704A41420051)
C23943-3 (704A41420020)
C23943-4 (704A41420027)
C23943-5 (704A41420029)
C23943-6 (704A41420035)
C23943-7 (704A41420035)
32/22/00/000/000/070
Actuating cylinder
MET 32.20.00.401 C23947-030 (704A41430020) TBO A20000 FH X A 0A
MET 32.20.01.401
WC 32.20.00.401 PRE MOD 0723817.
WC 32.20.01.401 POST MOD 0723817.
32/22/00/000/000/090
Actuating cylinder
C23947-020-1 (704A41430017) OC
C23947-020-2 (704A41430019)
C23947-2 (704A41430010)
32/40/00/401/000/010
Main landing gear - Heels
C20005 (704A41412003) OC
C20147-200 (704A41412008)
AS 532 SC
05-10-00
2018.08.17 ATA 32 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
32/40/00/402/000/010
Nose landing gear - Wheels
A20217-121 (704A41412005) OC
C20525000 (704A41412014)
32/40/00/403/000/000
Main landing gear - Brake
C20039-1 (704A41410009) OC
AS 532 SC
05-10-00
2018.08.17 ATA 32 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 33-LIGHTS
33/43/00/401/000/002
Light
4292187 (704A46820029) OC
SPECTROLAB SX 16
Aluminum arm only.
33/45/03/000/000/023
Searchlight - Gimbal arm
CMM 33.45.96 022929 (-) OTL A 10 Y X A 180 D
022929-11 (-)
022929-81 (-)
SPECTROLAB SX 16
Steel arm only.
AS 532 SC
05-10-00
2019.06.07 ATA 33 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 34-NAVIGATION
34-42 RADAR
34/42/07/000/000/005
Radar antenna 1400 - Drive system
4000504-0301 (N6707152800) TBO A 3000 FH XA 300 FH
4000504-0303 (N6707154000)
// 3Y XA 109 D
DA1203A
Return the equipment to an approved repair station for overhaul.
AS 532 SC
05-10-00
2013.01.10 ATA 34 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 35-OXYGEN
35/30/00/000/000/030
Oxygen mask
10100 (704A36240004) OC
35/30/00/000/000/055
Oxygen mask
10100 (704A36240004) TBO A 6Y X TSM 180 D
AS 532 SC
05-10-00
2015.10.15 ATA 35 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 36-PNEUMATIC
36/10/00/000/000/010
Filter - Filter element
MET 36.00.00.401 217-2 (NR084515220) OTL A 3000 FH XA 0A
217-3 (NR084515221)
Filter 217A01.
AS 532 SC
05-10-00
2014.01.09 ATA 36 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
45/11/00/000/000/055
EUROHUMS - DFDAU recorder - Battery
BR1225-1HB (-) OTL A 4Y X A 0A
BR1225-1HC (-)
BR1225-1HD (-)
BR1225-T2 (-)
BR1225-T2-1 (-)
45/11/02/000/000/020
EUROARMS - Recorder
980-6021-032 (704A45381025) OC
D51521-010-112 (704A45381021)
Recorders fitted with the DUKANE DK100 or DK120 or DATASONIC ELP-362D acoustic beacon.
AS 532 SC
05-10-00
2017.02.06 ATA 45 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 46-WEAPONS
46-00 WEAPONS
46/00/05/510/000/000
Ballistic protections – Crew doors and seats
120001 (704A31651028) OTL A 20 Y X TSM 30 D
120002 (704A41120200)
120003 (704A41120201)
120005 (704A41120202)
120007 (704A41120203)
120008 (704A31651029)
120009 (704A41120220)
AS 532 SC
05-10-00
2021.07.28 ATA 46 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
AS 532 SC
05-10-00
2013.01.10 ATA 47 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 52-DOORS
AS 532 SC
05-10-00
2021.07.28 ATA 52 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
ATA 55-STABILIZER
AS 532 SC
05-10-00
2013.01.10 ATA 55 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
62/35/00/000/000/090
MRH
MET 62.35.00.401 332A31-0001-03 (-) TBO A 1500 FH X A 150 FH
// 24 Y X A 180 D
PRE MOD 0743160
MRH POST MOD 0743066, 0743100 and fitted with the spindles MP/N 332A31-1485/1398,
all dash numbers (POST MOD 0743233).
62/35/00/000/000/095
MRH
MET 62.35.00.401 332A31-0001-04 (-) TBO A 1500 FH X A 150 FH
// 24 Y X A 180 D
PRE MOD 0743160
MRH fitted with the spindles MP/N 332A31-1485/1398, all dash numbers (POST MOD 0743233).
62/35/00/000/000/105
MRH
MET 62.35.00.401 332A31-0001-05 (-) TBO A 1500 FH X A 150 FH
// 24 Y X A 180 D
POST MOD 0743160
MRH POST MODs 0743066, 0743100 and fitted with spindles MP/N 332A31-1485/1398,
all dash numbers (POST MOD 0743233).
62/35/00/000/000/110
MRH
MET 62.35.00.401 332A31-0001-06 (-) TBO A 1500 FH X A 150 FH
// 24 Y X A 180 D
POST MOD 0743160
MRH fitted with the spindles MP/N 332A31-1485/1398, all dash numbers (POST MOD 0743233).
62/35/00/510/000/000
MRH - Frequency adapter
E1T2858-01 (704A33640040) OTL A 5700 OPCX A 0A
E1T3138-01 (704A33640050)
E1T3139-01 (704A33640052)
E3309F01 (704A33640098)
F1T3309-01 (704A33640060)
F1T3309-11 (704A33640068)
AS 532 SC
05-10-00
2021.07.28 ATA 62 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
AS 532 SC
05-10-00
2021.07.28 ATA 62 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
63/10/00/401/000/030
Engine-MGB coupling shaft assy
MET 63.10.00.401 332A54-0216-03 (-) TBO A 4800 FH X A 300 FH
// 24 Y X A 180 D
Assembly fitted with shafts MP/N 19E226-6A/7A.
63/10/00/401/000/080
Engine-MGB coupling shaft assy
MET 63.10.00.401 332A54-0216-04 (-) TBO A 4800 FH X A 300 FH
332A54-0216-05 (-)
332A54-0216-06 (-)
// 24 Y X A 180 D
63/10/00/401/000/100
Engine-MGB coupling shaft assy
MET 63.10.00.401 332A54-0217-00 (-) TBO A 4800 FH X A 300 FH
332A54-0217-01 (-)
// 24 Y X A 180 D
Assemblies fitted with shafts MP/N 332A54-2012-00/-01.
AS 532 SC
05-10-00
2019.06.07 ATA 63 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
63/20/00/401/000/010
Main reduction gear module
MET 63.20.00.401 332A32-2027-00 (-) TBO A 3000 FH X A 300 FH
332A32-2027-01 (-)
332A32-2027-02 (-)
// 24 Y X A 180 D
332A32-2027-03 (-)
332A32-2027-04 (-)
332A32-2027-05 (-)
332A32-2027-06 (-)
332A32-2027-07 (-)
332A32-2027-08 (-)
332A32-2027-09 (-)
332A32-2027-10 (-)
332A32-2027-11 (-)
Normal operation.
63/20/00/401/000/020
Main reduction gear module
MET 63.20.00.401 332A32-2027-00 (-) TBO A 2000 FH X A 200 FH
332A32-2027-01 (-)
332A32-2027-02 (-)
// 24 Y X A 180 D
332A32-2027-03 (-)
332A32-2027-04 (-)
332A32-2027-05 (-)
332A32-2027-06 (-)
332A32-2027-07 (-)
332A32-2027-08 (-)
332A32-2027-09 (-)
332A32-2027-10 (-)
332A32-2027-11 (-)
63/21/00/000/000/020
MGB - Filter - Filter element
MET 63.21.00.601 AR83-11-100 (-) OTL A 400 FH X A 40 FH
QA04081 (-)
§ F.2 // 2Y X A 73 D
ROBINDUS/IN-FLEX type
MGB lubricated with mineral oil.
63/21/00/000/000/025
MGB - Filter
FL1010 (704A44621031) TBO A 3000 FH X A 300 FH
// 24 Y X A 180 D
AS 532 SC
05-10-00
2019.06.07 ATA 63 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
63/24/00/401/000/010
Emergency oil pump
MET 63.24.00.401 177590 (704A44313032) TBO A 3000 FH X A 300 FH
31-75103-4035-5 (704A44313030)
7035-600 (704A44313015)
// 24 Y X A 180 D
7035-800 (704A44313020)
7056-000 (704A44313021)
7056-100 (704A44313027)
63/25/00/403/000/000
Fan
MET 63.25.00.403 332A39-0105-00 (-) OTL A 1200 FH X A 0A
332A39-0105-01 (-)
332A39-0105-02 (-)
63/25/00/403/000/010
Fan
MET 63.25.00.403 332A08-0466-01 (-) OTL A 5000 FH X A 0A
332A39-0107-00 (-)
63/25/00/403/000/020
Fan
MET 63.25.00.403 332A39-0107-01 (-) OTL A 7000 FH X A 0A
Fitted on assemblies: MP/N 332A39-0009-02/03.
AS 532 SC
05-10-00
2019.06.07 ATA 63 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
63/25/00/510/701/030
Fan - Bearing
MRM 63.25.00.701 6203F442M16 (704A33651073) OTL A 2500 FH X A 250 FH
// 3Y X A 109 D
PRE MOD 0725175
63/25/00/510/701/040
Fan - Bearing
MRM 63.25.00.701 6203F685M16 (704A33651167) OTL A 2500 FH X A 250 FH
// 5Y X A 180 D
63/27/00/401/000/210
Epicyclic reduction gear assembly
MET 63.27.00.401 332A32-2007-01 (-) TBO A 3000 FH X A 300 FH
332A32-2007-03 (-)
// 24 Y X A 180 D
Normal operation.
Normal operation.
63/29/00/510/401/010
Aft right accessory drive housing
MET 63.29.00.401 332A32-2016-00 (-) TBO A 2000 FH X A 200 FH
332A32-2016-01 (-)
332A32-2016-02 (-)
// 24 Y X A 180 D
332A32-2016-03 (-)
332A32-2017-00 (-)
332A32-2017-01 (-)
332A32-2017-04 (-)
AS 532 SC
05-10-00
2019.06.07 ATA 63 Page 4
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
63/29/00/510/401/020
Aft left accessory drive housing
MET 63.29.00.401 332A32-2023-00 (-) TBO A 3000 FH X A 300 FH
332A32-2023-01 (-)
332A32-2023-02 (-)
// 24 Y X A 180 D
332A32-2023-03 (-)
332A32-2025-00 (-)
332A32-2025-01 (-)
332A32-2025-07 (-)
Normal operation.
63/29/00/510/401/030
Aft left accessory drive housing
MET 63.29.00.401 332A32-2023-00 (-) TBO A 2000 FH X A 200 FH
332A32-2023-01 (-)
332A32-2023-02 (-)
// 24 Y X A 180 D
332A32-2023-03 (-)
332A32-2025-00 (-)
332A32-2025-01 (-)
332A32-2025-07 (-)
63/29/00/510/401/040
MGB that can be disengaged - Aft left accessory drive housing
MET 63.29.00.401 332A32-2022-00 (-) TBO A 2000 FH X A 0A
332A32-2022-01 (-)
332A32-2022-02 (-)
// 24 Y X A 0A
332A32-2022-03 (-)
332A32-2024-00 (-)
332A32-2024-01 (-)
332A32-2024-02 (-)
AS 532 SC
05-10-00
2019.06.07 ATA 63 Page 5
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
64/20/00/000/000/036
Tail rotor power transmission system
MET 64.20.00.401 332A33-0001-03 (-) TBO A 3500 FH X A 300 FH
// 24 Y X A 180 D
The tail rotor power transmission systems can be installed providing they have been modified
per POST MOD 0766022, 0766039 and 0766051.
64/20/00/000/000/065
Tail rotor power transmission system
MET 64.20.00.401 332A33-0001-04 (-) TBO A 3000 FH X A 300 FH
332A33-0001-05 (-)
332A33-0001-06 (-)
// 24 Y X A 180 D
332A33-0009-00 (-)
332A33-0009-01 (-)
64/20/00/000/000/066
Tail rotor power transmission system
MET 64.20.00.401 332A33-0001-04 (-) TBO A 3500 FH X A 300 FH
332A33-0001-05 (-)
332A33-0001-06 (-)
// 24 Y X A 180 D
332A33-0009-00 (-)
332A33-0009-01 (-)
64/20/00/301/000/000
Tail rotor power transmission system - Control rod - Bearing
SP22516B05RB20 (704A33651235) OTL A 3500 FH (P)A 0A
// 10 Y (P)A 0A
POST MOD 0766205
64/20/00/401/000/070
Tail rotor power transmission system - Feathering bearing stack
ESX40-5A (704A33651069) OTL A 3500 FH X A 300 FH
ESX40/1003RH3NY4TD(704A33651166)
Y28BB10895 (704A33651070)
// 6Y X A 180 D
Y28BB13233S5 (704A33651165)
Y28BB13233S6 (704A33651165)
AS 532 SC
05-10-00
2018.08.17 ATA 64 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
64/20/00/401/000/080
Tail rotor power transmission system - Feathering bearing stack
ESX40-5A (704A33651069) OTL A 3500 FH X A 300 FH
ESX40/1003RH3NY4TD(704A33651166)
Y28BB10895 (704A33651070)
// 6Y X A 180 D
Y28BB13233S5 (704A33651165)
Y28BB13233S6 (704A33651165)
64/20/00/401/000/090
Tail rotor power transmission system - Feathering bearing stack
ESX40-5A (704A33651069) OTL A 3500 FH X A 300 FH
ESX40/1003RH3NY4TD(704A33651166)
Y28BB10895 (704A33651070)
Y28BB13233S5 (704A33651165)
Y28BB13233S6 (704A33651165)
64/20/00/401/000/095
Tail rotor power transmission system - Feathering bearing stack
ESX40-5A (704A33651069) OTL A 3500 FH X A 300 FH
ESX40/1003RH3NY4TD(704A33651166)
Y28BB10895 (704A33651070)
// 6Y X A 180 D
Y28BB13233S5 (704A33651165)
Y28BB13233S6 (704A33651165)
64/20/00/401/000/100
Power transmission system - Control rod - Aft bearing
MET 64.20.00.406 330A33-9903-20 (-) OTL A 3500 FH X A 0A
// 5Y X A 0A
64/20/00/510/408/100
Tail rotor power transmission system
MET 64.20.00.408 332A33-0100-00 (-) TBO A 3000 FH X A 300 FH
// 24 Y X A 180 D
Operation involving frequent torque variations.
64/20/00/510/408/200
Tail rotor power transmission system
MET 64.20.00.408 332A33-0100-00 (-) TBO A 3500 FH X A 300 FH
// 24 Y X A 180 D
Normal operation.
AS 532 SC
05-10-00
2018.08.17 ATA 64 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
AS 532 SC
05-10-00
2018.08.17 ATA 64 Page 3
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
65/10/00/510/701/180
Non-regreasable bearing
MRM 65.10.00.701 28Y6009501M72 (704A33651096) OTL A 2400 FH X A 0A
BB1B649070A (704A33651097)
MRM 65.10.00.702 // 5Y X A 0A
65/10/00/510/701/190
Regreasable bearing
MRM 65.10.00.701 593353 (704A33651177) OTL A 3600 FH X A 300 FH
593354 (704A33651178)
MRM 65.10.00.702 // 5Y X A 180 D
593363 (704A33651179)
83A904DCS56 (704A33651136)
83A904E1-CS56 (-)
83A904ECS56 (704A33651149)
83A904F-1CS56 (-)
83A904FCS56 (704A33651151)
9109NP3 (704A33651148)
9109NPP3A3272A (704A33651120)
G9109NPP4 (704A33651152)
Components or assemblies with serial numbers that start with the letters WA and that are
lower than 10000 MUST NOT be installed.
65/20/00/401/000/020
IGB
MET 65.20.00.401 332A35-0002-01 (-) TBO A 3400 FH X A 0A
// 24 Y X A 0A
Components or assemblies with serial numbers that start with the letters WA and that are
lower than 10000 MUST NOT be installed.
AS 532 SC
05-10-00
2018.08.17 ATA 65 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
65/20/00/401/000/030
IGB
MET 65.20.00.401 332A35-0005-00 (-) TBO A 2600 FH X A 0A
332A35-0005-04 (-)
332A35-0005-05 (-)
// 24 Y X A 0A
332A35-0005-08 (-)
332A35-0005-09 (-)
65/20/00/401/000/040
IGB
MET 65.20.00.401 332A35-0010-00 (-) TBO A 3400 FH X A 0A
332A35-0010-01 (-)
332A35-0010-02 (-)
// 24 Y X A 0A
332A35-0010-03 (-)
65/20/00/401/000/050
IGB
MET 65.20.00.401 332A35-0005-06 (-) TBO A 3400 FH X A 0A
332A35-0005-07 (-)
// 24 Y X A 0A
AS 532 SC
05-10-00
2018.08.17 ATA 65 Page 2
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
AS 532 SC
05-10-00
2013.01.10 ATA 66 Page 1
MSM
Task Number
MP/N (PN) Limit Type Interval Margin
Description/Remarks
67-30 SERVOCONTROLS
67/30/00/401/000/005
Main servocontrol
MET 67.30.00.401 SC7202 (704A44831107) TBO A 3000 FH XA 0A
SC7203 (704A44831148)
// 20 Y XA 0A
TSM or Overhaul.
These servocontrols must not be installed with the servocontrols MP/N SC7221, MP/N SC7221-1.
67/30/00/401/000/007
Main servocontrol
MET 67.30.00.401 SC7221-1 (704A44831164) TBO A 3000 FH XA 0A
// 20 Y XA 0A
This servocontrol must not be installed with the servocontrols MP/N SC7202, MP/N SC7203.
67/30/00/401/000/010
Main servocontrol
MET 67.30.00.401 SC7221 (704A44831091) TBO A 3000 FH XA 0A
// 20 Y XA 0A
TSM or Overhaul.
These servocontrols must not be installed with the servocontrols MP/N SC7202, MP/N SC7203.
67/30/00/402/000/000
Tail servocontrol - SAMM
MET 67.30.00.402 SC7251 (704A44831108) TBO A 3000 FH XA 0A
// 20 Y XA 0A
TSM or Overhaul.
67/30/00/402/000/010
Tail servocontrol - SAMM
MET 67.30.00.402 SC7270 (704A44831072) TBO A 3000 FH XA 0A
// 20 Y XA 0A
TSM or Overhaul.
AS 532 SC
05-10-00
2013.01.10 ATA 67 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
05/21/00/602/000/000
Turnaround check
MET 05.21.00.602 A A TA X 0A
Check.
VC
05/21/00/603/000/000
Check after the last flight of the day
MET 05.21.00.603 A A ALF X 0A
Check.
GVI
05/21/00/604/000/000
Checking the optional equipment
MET 05.21.00.604 A A ALF X 0A
Check.
GVI
05/21/00/605/000/000
Aircraft preparation in cold weather
MET 05.21.00.605 A A BFF X 0A
Check.
VC
05/21/00/606/000/000
Aircraft preparation in cold weather
MET 05.21.00.606 A A ALF X 0A
Check.
GVI
05/21/00/607/000/000
Aircraft preparation in very cold weather
MET 05.21.00.607 A A ALF X 0A
Check.
GVI
AS 532 SC
05-20-00
2014.01.09 ATA 05 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
05/21/00/608/000/000
Aircraft preparation in very cold weather
MET 05.21.00.608 A A BFF X 0A
Check.
VC
AS 532 SC
05-20-00
2014.01.09 ATA 05 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
05/32/00/000/000/020
Preparation of check for corrosion
MET 05.32.00.301 A 2M X 6D
Helicopter based aboard a ship.
Check.
DI
AS 532 SC
05-20-00
2014.01.09 ATA 05 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
08/00/00/603/000/000
Aircraft
MET 08.00.00.603 A 7500 FH X 300 FH
Weighing after "End of inspection".
WGH
AS 532 SC
05-20-00
2015.04.16 ATA 08 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
21/00/00/601/000/000
Air conditioning system
MET 21.00.00.601 A 6Y X 180 D
Check.
DI
21-50 VENTILATION
21/50/00/601/000/000
Front aerator
MET 21.50.00.601 A 6Y X 180 D
Check.
DI
21/52/00/000/000/010
Filter - Filter element
CMM 21.59.25 A 500 FH X 50 FH
Cleaning.
CLN
21/52/00/000/000/020
Air conditioning
CMM 21.59.23 A 1500 FH X 150 FH
Replacing the textile liner subassembly, extracting water.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 21 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
21/52/00/601/000/000
Air conditioning
MET 21.52.00.601 A 500 FH X 50 FH
EXC. § F.2
Check..
DI
21/52/00/601/000/015
Air conditioning - Anti-vibration mounting
MET 21.52.00.601 A 500 FH X 50 FH
§ F.2 // 2Y X 73 D
Check.
DI
21/53/00/000/000/015
R22 cold air unit
CMM 21.59.94 A 500 FH X 50 FH
// 2Y X 73 D
788A040101 (704A42110014)
Cleaning the condenser air inlet and outlet and the evaporator air inlet on covering panel.
CLN
21/53/00/000/000/020
R22/R134A cold air unit
MET 21.53.00.502 A 1M X 3D
788A040101 (704A42110014)
788AA010101 (704A42110145)
Functional test.
FT
AS 532 SC
05-20-00
2018.02.05 ATA 21 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
21/53/00/601/000/010
R22/R134A air conditioning
MET 21.53.00.601 A 500 FH X 50 FH
EXC. § F.2
788A040101 (704A42110014)
788AA010101 (704A42110145)
Visual check.
VC
21/53/00/601/000/015
R22/R134A air conditioning - Anti-vibration mounting
MET 21.53.00.601 A 500 FH X 50 FH
§ F.2 // 2Y X 73 D
Visual check.
VC
AS 532 SC
05-20-00
2018.02.05 ATA 21 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
22/00/00/000/000/030
Safety switching circuits
MET 22.40.10.601 A 7500 FH X 300 FH
Check.
DI
22/30/10/601/000/010
155P autopilot hydraulic system
MET 22.30.10.601 A 50 FH X 5 FH
§ F.4
Check.
DI
22/30/10/601/000/015
APM 2010 autopilot hydraulic system
MET 22.31.00.601 A 50 FH X 5 FH
§ F.4
Check.
GVI
22/30/10/601/000/020
APM 2010 autopilot hydraulic unit
MET 22.31.00.601 A 2Y X 73 D
§ F.3
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 22 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
22/30/10/602/000/000
155P autopilot hydraulic unit - Yaw channel
MET 22.30.10.602 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
22/30/10/611/000/000
155P autopilot hydraulic unit - Accumulator
MET 22.30.10.611 A 2Y X 73 D
Charge check.
DI
22/30/10/611/000/010
APM 2010 autopilot hydraulic unit - Accumulator
MET 22.31.00.611 A 2Y X 73 D
Charge check.
DI
22/30/10/612/000/000
Autopilot hydraulic unit - Heating circuit
MET 22.30.10.612 A 500 FH X 50 FH
Check.
22/50/16/601/000/000
CDV85 4-axis coupler
MET 22.50.16.601 A 500 FH X 50 FH
MET 22.50.16.602 // 2Y X 73 D
MET 22.50.16.603
MET 22.50.16.604
MET 22.50.16.605
MET 22.50.16.606
MET 22.50.16.607
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 22 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
22/50/20/601/000/000
4-axis coupler
MET 22.50.20.601 A 500 FH X 50 FH
MET 22.50.20.602 // 1Y X 36 D
CDV155
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 22 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 23-COMMUNICATIONS
23/11/00/601/000/010
SSB HF antenna - Cable stop
MET 23.11.09.601 A 500 FH X 50 FH
§ H.2
MET 23.11.10.601
§ H.2
Check.
SSB antenna equipped with the cable stop MP/N 332P65-1473-00.
DI
23/71/00/520/511/000
CVFDR Recorder without EUROHUMS option - Immersion probe
MET 23.71.00.511 A 2Y X 73 D
Functional test.
FT
23/71/00/520/512/000
CVFDR Recorder without EUROHUMS option
MET 23.71.00.512 A (*) A X 0A
980-6021-032 (704A45381025)
980-6021-066 (704A45381029)
AR-204C, AR-602C.
(*) CVR function test before the first flight.
FT
AS 532 SC
05-20-00
2021.07.28 ATA 23 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
23/71/00/520/512/005
CVFDR Recorder without EUROHUMS option
MET 23.71.00.512 A (*) A X 0A
D51521-010-112 (704A45381021)
Type 2000.
(*) CVR function test before the first flight.
FT
23/71/00/520/512/010
CVFDR Recorder without EUROHUMS option
MET 23.71.00.512 A 6M X 18 D
980-6021-032 (704A45381025)
980-6021-066 (704A45381029)
AR-204C, AR-602C.
CVR function test.
FT
23/71/00/520/512/015
CVFDR Recorder without EUROHUMS option
MET 23.71.00.512 A 6M X 18 D
D51521-010-112 (704A45381021)
Type 2000.
CVR function test.
FT
23/71/00/520/514/000
CVFDR Recorder without EUROHUMS option
MET 23.71.00.514 A 6M X 18 D
980-6021-032 (704A45381025)
980-6021-066 (704A45381029)
AR-204C, AR-602C.
Test of the erase function.
FT
23/71/00/520/514/005
CVFDR Recorder without EUROHUMS option
MET 23.71.00.514 A 6M X 18 D
D51521-010-112 (704A45381021)
Type 2000.
Test of the erase function.
FT
AS 532 SC
05-20-00
2021.07.28 ATA 23 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
23/71/00/520/531/000
CVFDR Recorder without EUROHUMS option
MET 23.71.00.531 A 1Y X 36 D
§F
980-6021-032 (704A45381025)
980-6021-066 (704A45381029)
AR-204C, AR-602C.
FDR and CVR Data Check.
FT
23/71/00/520/531/005
CVFDR Recorder without EUROHUMS option
MET 23.71.00.531 A 1Y X 36 D
§F
D51521-010-112 (704A45381021)
Type 2000.
FDR and CVR Data Check.
FT
23/71/01/520/502/000
Cockpit voice recorder - Immersion probe
MET 23.71.01.502 A 2Y X 73 D
64762-001-1 (704A37722023)
Functional test.
FT
23/71/01/520/601/000
Cockpit voice recorder
MET 23.71.01.601 A 500 FH X 50 FH
Check.
GVI
23/71/02/520/502/000
Cockpit voice recorder - Immersion probe
MET 23.71.02.502 A 2Y X 73 D
64762-001-1 (704A37722023)
FA2100.
Functional test.
FT
AS 532 SC
05-20-00
2021.07.28 ATA 23 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/00/00/601/000/000
Electrical power generating system
MET 24.00.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
GVI
24/00/00/603/000/000
Electrical bonding
MET 24.00.00.603 A 7500 FH X 300 FH
Check.
DI
24/20/00/000/000/040
Alternator
CMM 24.29.59 A 500 FH X 50 FH
AL0672V01 (704A46220030)
AL9472V01 (704A46220031)
Bearing replacement.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/20/00/000/000/050
Alternator
CMM 24.29.59 A 1000 FH X 100 FH
AL0672V01-1 (704A46220034)
AL9472V01-1 (704A46220033)
Bearing replacement.
DI
24/30/00/601/000/000
Electrical master box protection board
MET 24.30.00.602 A 4Y X 146 D
Check.
DI
24-31 BATTERY
24/31/00/000/000/000
43 Ah battery - Heating system
MET 24.90.10.501 A 500 FH X 50 FH
40208-5 (704A46130038)
40408 (704A46130034)
Functional test.
FT
24/31/00/000/000/005
Battery
MET 24.30.00.201 A 2Y X 73 D
40208-1 (704A46130020)
40208-5 (704A46130038)
40408 (704A46130034)
Battery compartment cleaning.
CLN
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/31/00/000/000/020
Battery
CMM 24.30.99 A 6M X 18 D
INSPECTION/CHECK
§6
40208-1 (704A46130020)
40208-5 (704A46130038)
40408 (704A46130034)
Check.
DI
24/31/00/000/000/030
Battery
CMM 24.30.99 A 1Y X 36 D
INSPECTION/CHECK
§7
40208-1 (704A46130020)
40208-5 (704A46130038)
40408 (704A46130034)
Check.
DI
24/31/00/000/000/040
Battery
CMM 24.30.99 A 2Y X 73 D
INSPECTION/CHECK
§8
40208-1 (704A46130020)
40208-5 (704A46130038)
40408 (704A46130034)
Detailed inspection.
DI
24/31/00/000/000/100
40 Ah battery - Heating system
MET 24.90.11.501 A 500 FH X 50 FH
60061200401 (704A46130048)
Functional test.
FT
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/31/00/000/000/120
Battery
CMM 24.32.99 A 6M X 18 D
CHECK § 5.2
CHECK § 5.3
60061200401 (704A46130048)
60061200402 (704A46130047)
Visual inspection and electrical check.
VC|FT
24/31/00/000/000/130
Battery
CMM 24.32.99 A 2Y X 73 D
CHECK § 6
60061200401 (704A46130048)
60061200402 (704A46130047)
Overhaul.
DI
24/31/00/000/000/220
Standby battery
MET 24.31.00.501 A 500 FH X 50 FH
§E // 2Y X 73 D
EE0005 (704A46130021)
EE0005-01 (704A46130026)
EE0005-011 (704A46130031)
EE0005-0111 (704A46130032)
Charge test.
FT
24/31/00/000/000/230
Standby battery
MET 24.31.00.501 A 2Y X 73 D
§F
EE0005 (704A46130021)
EE0005-01 (704A46130026)
EE0005-011 (704A46130031)
EE0005-0111 (704A46130032)
Switching test.
FT
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/31/00/000/000/250
Standby battery
MET 24.31.00.502 A 1000 FH X 100 FH
§ F.1 // 3Y X 109 D
BTS03A (704A46130053)
POST MOD 0726647
Charge test.
FT
24/31/00/000/000/260
Standby battery
MET 24.31.00.502 A 3Y X 109 D
§ F.2
BTS03A (704A46130053)
POST MOD 0726647
Switching test.
FT
24/31/00/000/000/270
Standby battery
MET 24.31.00.601 A 1000 FH X 100 FH
§ F.7 // 3Y X 109 D
BTS03A (704A46130053)
Capacity measurement.
24/31/00/000/000/280
Standby battery
MET 24.31.00.501 A 1000 FH X 100 FH
§ F.1 // 3Y X 109 D
BTS03A (704A46130053)
PRE MOD 0726647
Charge test.
FT
24/31/00/000/000/290
Standby battery
MET 24.31.00.501 A 3Y X 109 D
§ F.2
BTS03A (704A46130053)
PRE MOD 0726647
Switching test.
FT
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
24/31/00/000/000/460
Standby battery
MET 24.31.00.601 A 500 FH X 50 FH
§ F.7 // 2Y X 73 D
EE0005 (704A46130021)
EE0005-01 (704A46130026)
EE0005-011 (704A46130031)
EE0005-0111 (704A46130032)
Capacity measurement.
DI
24/31/00/520/501/100
Standby battery
MET 24.31.00.501 A 1000 FH X 100 FH
§E // 3Y X 109 D
BTS89A (704A46130042)
Charge test.
FT
24/31/00/520/501/200
Standby battery
MET 24.31.00.501 A 3Y X 109 D
§F
BTS89A (704A46130042)
Switching test.
FT
24/31/00/520/601/100
Standby battery
MET 24.31.00.601 A 1000 FH X 100 FH
§ F.7 // 3Y X 109 D
BTS89A (704A46130042)
Capacity measurement.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 24 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 25-EQUIPMENTS/FURNISHINGS
25-00 EQUIPMENTS/FURNISHINGS
25/00/00/000/000/015
Belt straps - Harness - Medical installation straps
MET 25.00.00.601 A 1Y X 36 D
MET 25.24.00.601
Check.
Operation also to be carried out after each installation of the seat or of the harness or of the straps.
CLN|GVI
25/00/00/000/000/020
Belt straps - Harness - Medical installation straps
MET 25.00.00.501 A 1Y X 36 D
Functional test.
Operation also to be carried out after each installation of the seat or of the harness or of the straps.
FT
25-10 COCKPIT
25/10/00/000/000/000
Cockpit
A 7500 FH X 300 FH
Removal-installation of the pilot's, copilot's, 3rd crew member's and passengers' seats
and of the soundproofing mats.
DI
25/10/00/601/000/000
Cockpit
MET 25.10.00.601 A 6Y X 180 D
Check the furnishings.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/25/00/601/000/010
Confort seats
MET 25.27.06.601 A 7500 FH X 300 FH
System check.
DI
25/62/00/000/000/000
Cylinder
CMM 25.69.11 A 1Y X 36 D
INSPECTION/CHECK
§2
Interval between 2 cylinder weighing or checking operations.
Weighing or pressure check after removal of cylinders from store.
DI
25/62/00/000/000/100
Emergency floatation gear
CMM 25.69.70 A 1Y X 36 D
INSPECTION /
CHECK
25-69-70-220-001-A01
Maintenance.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/62/00/000/000/110
Emergency floatation gear
CMM 25.69.70 A 3M X 9D
INSPECTION /
CHECK
25-69-70-220-001-A01
Tropical and damp atmosphere
Maintenance.
Applicable on the following floats:
- Forward: MP/N 158820-0/1 with S/N lower than 500,
- Aft left : MP/N 207035-0 with S/N lower than 60,
- Aft right : MP/N 207036-0 with S/N lower than 60.
DI
25/62/00/000/000/120
Emergency floatation gear - Immersion probe
MET 25.62.00.502 A 500 FH X 50 FH
// 2Y X 73 D
Functional test.
FT
25/62/00/603/000/000
Collective pitch lever - Percussion control pushbutton
MET 25.62.00.603 A 1Y X 36 D
MET 25.62.01.603
13445A (N6718900500)
13445AX640 (NR779400001)
Tropical and damp atmosphere
Salt-laden atmosphere
Check.
DI
25/62/01/401/000/011
Cylinder kevlar and fiber glass
CMM 25.69.11 A 3Y X 0A
MET 25.62.01.401 // 1 OPCX 0A
200740-0 (-)
200740-1 (-)
Proof pressure check.
TSM or the last proof test.
1 OPC = 1 utilization (ditching or untimely percussion of the inflation cylinder).
To be carried out by the manufacturer or by an approved repair station.
NPT
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/62/01/401/000/016
Cylinder carbon
CMM 25.69.11 A 5Y X 0A
MET 25.62.01.401 // 1 OPCX 0A
200740-2 (704A42693012)
Proof pressure check.
TSM or the last proof test.
1 OPC = 1 utilization (ditching or untimely percussion of the inflation cylinder).
To be carried out by the manufacturer or by an approved repair station.
NPT
25/62/01/501/000/000
Emergency floatation gear
MET 25.62.01.501 A 1000 FH X 100 FH
System test.
FT
25/62/01/501/000/010
Cylinder - Inflation head frangible disc
MET 25.62.01.501 A 1Y X 36 D
§ F.2
200740-0 (-)
200740-1 (-)
202458-0 (-)
202458-1 (-)
Check.
DI
25/62/01/601/000/000
Emergency floatation gear
MET 25.62.01.601 A 2Y X 73 D
EXC. § F.1.c, F.3.b
Equipment checks.
DI
25/62/01/601/000/010
Cradles
MET 25.62.01.601 A 10 Y X 180 D
MET 25.62.01.602
Normal climatic conditions
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/62/01/601/000/020
Cradles
MET 25.62.01.601 A 5Y X 180 D
MET 25.62.01.602
Tropical and damp atmosphere
Check.
DI
25/64/00/000/000/010
Hydraulic hoist 50 m / 600 lbs, constant speed
CMM 25.64.96 A 1Y X 0A
// 500 HC X 0A
76360-200 (704A41815057)
76363-200-A (-)
76363-300 (-)
Drum oil level check.
SVC
25/64/00/000/000/030
Hoist system
Salt-laden atmosphere
Rinsing the unreeled cable with fresh water and drying the cable.
Draining and drying the cavity in the hook sleeve.
These operations are to be carried out whether or not the hoist has been used over the sea.
After hovering or flight at low altitude, these operations must be performed during the ALF check.
CLN
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/64/00/000/000/040
Hydraulic hoist 50 m / 600 lbs, variable speed
CMM 25.62.21 A 6M X 0A
// 50 HC X 0A
76360-210-00 (704A41815058)
76360-210-01 (704A41815059)
76360-210-0D (704A41815115)
76360-210-1D (704A41815114)
Check of:
- the efficiency of the return spring of the latch of the mechanical End-of-Travel,
- the cable,
- the cable extracting and reeling in,
- the hook assembly,
- the hook compression function,
- functional check of the slow-down(s) and the electrical End-of-Travels.
DI
25/64/00/000/000/050
Hydraulic hoist 50 m / 600 lbs, constant speed
CMM 25.64.96 A 6M X 0A
// 50 HC X 0A
76360-200 (704A41815057)
76363-200-A (-)
76363-300 (-)
Check of:
- the efficiency of the return spring of the latch of the mechanical End-of-Travel,
- the cable,
- the cable extracting and reeling in,
- the hook assembly,
- functional check of the electrical End-of-Travels.
DI
25/64/01/000/000/000
Hydraulic hoist 75 m / 600 lbs, variable speed
CMM 25.64.98 A 6M X 0A
// 50 HC X 0A
76365-230 (704A41815060)
Greasing of the winding screw.
Check of:
- the efficiency of the return spring of the latch of the mechanical End-of-Travel,
- the cable,
- the cable extracting and reeling in,
- the hook assembly,
- the hook compression function,
- functional check of the slow-down(s) and the electrical End-of-Travels.
DI|LUB
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/64/01/601/000/000
Hoist installation
MET 25.64.05.603 A 1500 FH X 150 FH
// 4Y X 146 D
Check.
DI
25/64/01/601/000/050
Hydraulic hoist 75 m / 600 lbs, variable speed
CMM 25.64.98 A 1Y X 0A
// 500 HC X 0A
76365-230 (704A41815060)
Check:
- drum oil level check,
- of the mechanic brake,
- of the condition of the micro-switches box.
DI|SVC
25/64/01/601/000/060
Hydraulic hoist 75 m / 600 lbs, variable speed
CMM 25.64.98 A 6M X 0A
// 50 HC X 0A
76368-200 (704A41815061)
76368-240 (704A41815062)
76368-240-D (704A41815083)
Greasing of the winding screw.
Check of:
- the cable,
- the cable extracting and reeling in,
- the hook assembly,
- the hook compression function,
- functional check of the slow-down(s) and the electrical End-of-Travels.
PMP not applicable = TSI.
DI|LUB
25/64/01/601/000/070
Hydraulic hoist 75 m / 600 lbs, variable speed
CMM 25.64.98 A 1Y X 0A
// 500 HC X 0A
76368-200 (704A41815061)
76368-240 (704A41815062)
76368-240-D (704A41815083)
Check:
- drum oil level check,
- of the mechanic brake,
- of the condition of the micro-switches box for hoist without amendment 23.
PMP not applicable = TSI.
DI|SVC
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/64/01/601/000/080
Hydraulic hoist 75 m / 600 lbs, variable speed
CMM 25.64.98 A 2Y X 0A
// 1000 HC X 0A
76365-230 (704A41815060)
76368-200 (704A41815061)
76368-240 (704A41815062)
76368-240-D (704A41815083)
Drum oil drainage.
PMP not applicable = TSI.
DRN
25/64/02/000/000/010
Electric hoist 28 VDC 34 m / 300 lbs, constant speed
CMM 25.69.61 A 6M X 18 D
SECTION III
BL16600-120 (704A41815022)
BL16600-120-1 (-)
BL16600-180 (704A41815037)
BL16600-90 (704A41815019)
Check.
PMP not applicable = TSI.
DI
25/64/02/000/000/015
Electric hoist 28 VDC 34 m / 300 lbs, constant speed - Cable
CMM 25.69.61 A 6M X 18 D
SECTION III // 50 HC X 5 HC
BL7505 (-)
Check.
PMP not applicable = TSI.
DI
25/64/02/000/000/110
Electrical hoist - Transformer rectifier
MET 25.64.05.405 A 3500 FH X 300 FH
// 6Y X 180 D
684-1009-200 (704A46230004)
Removal for return to an approved workshop for cleaning, checking and testing.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 8
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/64/02/000/000/200
Electric hoist 28 VDC 40 m / 300 lbs, constant speed
CMM 25.64.97 A 6M X 0A
// 50 HC X 0A
76370-130 (704A41815035)
76370-140-D (704A41815085)
Greassing of:
- the mechanical brake,
- the winding screw.
Check of:
- the efficiency of the return spring of the latch of the mechanical,
- the cable,
- the cable extracting and reeling in,
- the hook assembly,
- functional check of the electrical End-of-Travels.
PMP not applicable = TSI.
DI|LUB
25/64/02/000/000/300
Electric hoist 28 VDC 40 m / 300 lbs, constant speed - Electrical box
CMM 25.64.97 A 100 HC X 0A
Check of the electric resistors of the box.
DI
25/64/02/000/000/400
Electric hoist 28 VDC 40 m / 300 lbs, constant speed - Guiding fork
CMM 25.64.97 A 750 HC X 0A
Removal for remplacement.
DS
25/64/02/000/000/580
Electric hoist 115 VAC 90 m / 600 lbs, variable speed
CMM 25.61.10 A 1M X 3D
SECTION 500 // 25 HC X 2 HC
BL29900-59 (704A41815089)
Check of:
- the cable,
- the hook assembly.
PMP not applicable = TSI.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 9
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/64/02/000/000/590
Electric hoist 115 VAC 90 m / 600 lbs, variable speed
CMM 25.61.10 A 6M X 18 D
SECTION 500 // 100 HC X 10 HC
BL29900-59 (704A41815089)
Check:
- extraction rollers,
- extraction roller clutch,
- extraction system clutch,
- cable outlet casing / roller assembly,
- incorrect winding detector,
- oil level,
- guide screw,
- electrical harnesses.
PMP not applicable = TSI.
DI
25/64/02/000/000/600
Electric hoist 115 VAC 90 m / 600 lbs, variable speed
CMM 25.61.10 A 1Y X 36 D
SECTION 500 // 400 HC X 40 HC
BL29900-59 (704A41815089)
Test.
PMP not applicable = TSI.
FT
25/64/05/000/000/010
Hoist intallation
MET 25.64.05.601 A 1500 FH X 150 FH
// 4Y X 146 D
Jettison sytem functional tests.
FT
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 10
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/66/00/000/000/010
Emergency locator transmitter
CMM 25.65.98 A 6M X 18 D
§ 4.A
BCAL CPT 606.
Control of the system on the ground.
FT
25/66/00/000/000/030
Emergency locator transmitter - Radar receiver
CMM 25.65.98 A 1Y X 36 D
§ 4.C
BCAL CPT 606.
Test.
FT
25/66/00/000/000/032
Emergency locator transmitter
CMM 25.65.98 A 1Y X 36 D
PAGE 501, 502,
503, 504
BCAL CPT 606.
Check of the mechanism of display and the support with removal.
DI
25/66/00/000/000/100
Battery
CMM 25.60.03 A 6M X 18 D
LEIGH CPI 113.
Battery charge check.
DI
25/66/00/000/000/150
ARU-18 Ejection system
CMM 25.60.03 A 1Y X 36 D
LEIGH CPI 113.
Checks, cleaning and lubrication.
DI|CLN|LUB
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 11
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/66/00/000/000/170
Emergency locator transmitter
A 500 FH X 50 FH
EBC302HM.
Operational test in compliance with the Manufacturer Manual.
FT
25/66/00/000/000/260
Emergency locator transmitter
MET 25.66.31.501 A 6M X 18 D
ELT96A2560000000 (704A45737043)
SOCATA
Emergency locator transmission auto-test (Carry out 3 successive sequences).
FT
25/66/00/000/000/270
Emergency locator transmitter
MET 25.66.31.601 A 500 FH X 50 FH
// 2Y X 73 D
ELT96A2560000000 (704A45737043)
SOCATA.
Check.
GVI
25/66/00/520/000/230
Underwater acoustic beacon
CMM 25.69.73 A 3M X 9D
SEC.III
§ 3.3
N15F210B (704A45737011)
DUKANE 210B.
Cleaning and check.
CLN|FT
25/66/00/520/000/350
Underwater acoustic beacon
CMM 25.66.97 A 1Y X 36 D
§ 5.2
§ 5.3
DUKANE DK100.
Cleaning and checks.
CLN|DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 12
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/66/00/520/000/360
Underwater acoustic beacon
CMM 25.66.97 A 1Y X 36 D
§ 6.2
§ 6.3
DUKANE DK120.
Cleaning and checks.
CLN|DI
25/66/00/520/000/370
Underwater acoustic beacon
CMM 25.60.07 A 1Y X 36 D
DATASONIC ELP 362D.
Cleaning and checks.
CLN|FT
25/66/01/501/000/000
Emergency locator transmitter
MET 25.66.01.501 A 6M X 18 D
JOLLIET JE2-1978-0/JE2-1978-0-NG
Functional test.
FT
25/66/01/601/000/000
Emergency locator transmitter
MET 25.66.01.601 A 500 FH X 50 FH
// 2Y X 73 D
JOLLIET JE2-1978-0/JE2-1978-0-NG
Check.
GVI
25/66/04/601/000/000
Emergency locator transmitter
MET 25.66.04.601 A 500 FH X 50 FH
LEIGH CPI 113.
Check.
GVI
25/66/33/501/000/000
Emergency locator transmitter
MET 25.66.33.501 A 1M X 3D
KANNAD 406 AF/AP.
Auto-test.
FT
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 13
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/66/33/601/000/000
Emergency locator transmitter
MET 25.66.33.601 A 500 FH X 50 FH
// 2Y X 73 D
KANNAD 406-AF/AP.
System check.
GVI
25/69/00/000/000/070
Cylinder
CMM 25.66.96 A 5Y X 0A
158410 (-)
Proof pressure check.
To be carried out by the manufacturer or by an approved workshop.
TSM or the last proof test.
NPT
25/69/00/000/000/090
Life raft
CMM 25.69.78 A 1Y X 36 D
Check, life raft tightness testing, cylinder weighing.
DI|WGH
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 14
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/69/00/000/000/165
Cylinder
CMM 25.69.78 A 5Y X 0A
204502-0 (-)
217740-0 (-)
Proof pressure check.
To be carried out by the manufacturer or by an approved workshop.
TSM or last proof test.
NPT
25/69/10/501/000/000
Sponson-mounted life raft
MET 25.69.10.501 A 500 FH X 50 FH
Test.
FT
25/69/10/601/000/000
Sponson-mounted life raft
MET 25.69.10.601 A 500 FH X 50 FH
Equipment checks.
DI
25/69/10/601/000/010
Sponson-mounted life raft
MET 25.69.10.601 A 100 FH X 10 FH
§ F.5
PRE MOD 0722408
Container checks.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 15
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/69/10/602/000/000
Sponson-mounted life raft
MET 25.69.10.602 A 500 FH X 50 FH
§ F.1
204359-1 (-)
204359-2 (-)
204360-1 (-)
204360-2 (-)
205379-5 (704A42691026)
205379-6 (704A42691046)
205380-5 (704A42691027)
205380-6 (704A42691045)
2192350 (704A42691052)
2192360 (704A42691053)
245533-0 (704A42691049)
245534-0 (704A42691050)
Check of the frangible disc resistors.
DI
25/69/10/602/000/010
Sponson-mounted life raft
MET 25.69.10.602 A 500 FH X 50 FH
§ F.2
Insulation check.
DI
25/81/00/000/000/015
4.5-ton sling - Electric equipment
MET 25.81.00.501 A 7D X 0A
§ F.1
§ F.2
PRE MOD 0726645
Functional test.
FT
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 16
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/81/00/000/000/016
4.5-ton sling - Electric equipment
MET 25.81.00.504 A 7D X 0A
POST MOD 0726645
Functional test.
FT
25/81/00/000/000/017
3-ton sling - Release unit manual control
MET 25.81.02.501 A 7D X 0A
§ F.1
§ F.2
Test.
FT
25/81/00/000/000/018
2-ton sling - Release unit manual control
MET 25.81.01.501 A 7D X 0A
Test.
FT
25/81/00/000/000/020
Cargo hook - Release control
MET 25.81.0X.60X A 3Y X 109 D
Normal climatic conditions
Manual control check and greasing.
DI|LUB
25/81/00/000/000/023
Cargo hook - Release control
MET 25.81.0X.60X A 30 M X 90 D
Salt-laden atmosphere
Manual control check and greasing.
DI|LUB
25/81/00/601/000/010
4.5-ton sling
MET 25.81.00.601 A 3M X 9D
// 500 SC X 50 SC
System check and greasing.
DI|LUB
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 17
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/81/00/601/000/020
4.5-ton sling
MET 25.81.00.502 A 500 FH X 50 FH
// 2Y X 73 D
PRE MOD 0726645
Dynamometric system test.
FT|RIG
25/81/00/601/000/025
4.5-ton sling
MET 25.81.00.505 A 500 FH X 50 FH
// 2Y X 73 D
POST MOD 0726645
Dynamometric system test.
FT|RIG
25/81/00/602/000/000
4.5-ton sling - Arming unit
MET 25.81.00.602 A 500 SC X 50 SC
Detailed check.
DI
25/81/00/603/000/000
4.5-ton sling
MET 25.81.00.603 A 500 SC X 100 SC
§F
Operation involving frequent torque variations.
Special monitoring.
DI
25/81/00/603/000/010
4.5-ton sling
MET 25.81.00.603 A 2500 SC X 500 SC
§G
Operation involving frequent torque variations.
Special monitoring.
DI
25/81/00/603/000/020
4.5-ton sling
MET 25.81.00.603 A 25 FH X 2 FH
§I // 250 SC X 25 SC
Operation involving frequent torque variations.
Special monitoring.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 18
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/81/00/603/000/030
4.5-ton sling
MET 25.81.00.603 A 500 FH X 50 FH
§H
Operation involving frequent torque variations.
Special monitoring.
DI
25/81/01/601/000/000
2-ton sling
MET 25.81.01.601 A 2Y X 73 D
// 500 SC X 50 SC
Check.
DI
25/81/02/401/000/020
Rotatingrelease unit
CMM 25.81.99 A 2Y X 73 D
§ INSPECTION // 500 SC X 50 SC
AS21-10 (704A41811033)
Greasing.
LUB
25/81/02/401/000/030
Rotating release unit
CMM 25.89.92 A 2Y X 73 D
§ INSPECTION // 500 SC X 50 SC
AS21-7 (704A41811026)
AS21-7-1 (704A41811028)
AS21-7-2 (704A41811031)
AS21-7-3 (704A41811032)
Greasing.
PMP not applicable = TSI.
LUB
25/81/02/502/000/000
3-ton sling
MET 25.81.02.502 A 500 FH X 50 FH
// 2Y X 73 D
AS21-7 (704A41811026)
AS21-7-1 (704A41811028)
AS21-7-2 (704A41811031)
Dynamometric system test.
FT|RIG
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 19
MSM
Task Number
Documentation Interval Margin
Description/Remarks
25/81/02/601/000/000
3-ton sling
MET 25.81.02.601 A 2Y X 73 D
// 500 SC X 50 SC
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 25 Page 20
MSM
Task Number
Documentation Interval Margin
Description/Remarks
26/11/00/501/000/010
Fire detection
MET 26.11.00.501 A 500 FH X 50 FH
§ F.2.c
§ F.2.d
§ G.1.c
§ G.1.d
POST MOD 0726490.
Electric system testing.
FT
AS 532 SC
05-20-00
2020.07.31 ATA 26 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
26/13/00/601/000/010
Detector
MET 26.13.00.601 A 500 FH X 50 FH
§ F.1 // 2Y X 73 D
H342 (704A42820033)
Visual check.
Functional test.
FT|GVI
26/13/00/601/000/020
Detector
MET 26.13.00.601 A 500 FH X 50 FH
§ F.2 // 2Y X 73 D
332A08-8651-02 (-)
H352 (704A42820050)
Visual check.
Functional test.
GVI|FT
26/21/00/401/000/000
Extinguisher bottle
MET 26.21.00.401 A 5Y X 0A
MET 26.21.00.402
32700014 (704A42820015)
860-830 (704A42820014)
AS 532 SC
05-20-00
2020.07.31 ATA 26 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
26/21/00/401/000/010
Extinguisher bottle
MET 26.21.00.401 A 7Y X 0A
MET 26.21.00.402
862690-00 (704A42820028)
863490-00 (704A42820038)
863490-01 (704A42820046)
Proof pressure check.
TSM or the last proof test.
To be carried out by the manufacturer or by an approved workshop.
WC 26.21.00.401 PRE MOD 0723817.
WC 26.21.00.402 POST MOD 0723817.
NPT
26/21/00/501/000/000
Fire extinguishing
MET 26.21.00.501 A 7500 FH X 300 FH
Percussion test.
FT
26/21/00/601/000/000
Fire extinguishing system
MET 26.21.00.601 A 2Y X 73 D
Check.
DI
26/21/00/602/000/000
Steel fire extinguisher
MET 26.21.00.602 A 6M X 18 D
§F
32700014 (704A42820015)
860-830 (704A42820014)
862690-00 (704A42820028)
Weighing.
WGH
26/21/00/602/000/010
Pyrotechnical cartridge
MET 26.21.00.602 A 6M X 18 D
§E
861345 (704A38710020)
861355 (704A38710021)
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 26 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
26/21/00/602/000/011
Pyrotechnical cartridge
MET 26.21.00.602 A 1Y X 36 D
§E
863080-00 (704A38710040)
863085-00 (704A38710041)
Check.
DI
26/21/00/603/000/015
Double check valve
MET 26.21.00.603 A 2Y X 73 D
Check.
DI
26/22/00/000/000/021
Hand fire extinguisher - Cylinder
CMM 26.21.20 A 6M X 18 D
C1M1-20400 (-)
Weighing.
WGH
26/22/00/000/000/025
Hand fire extinguisher - Cylinder
CMM 26.21.30 A 6M X 18 D
14398 (N6752401521)
230-101-000-02 (N6752401521)
Weighing.
WGH
AS 532 SC
05-20-00
2020.07.31 ATA 26 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
26/22/00/000/000/030
Hand fire extinguisher - Cylinder
CMM 26.21.20 A 5Y X 0A
C1M1-20400 (-)
Proof pressure check.
TSM or the last proof test.
To be carried out by the manufacturer or by an approved workshop.
NPT
26/22/00/000/000/040
Hand fire extinguisher - Cylinder
CMM 26.21.30 A 5Y X 0A
14398 (N6752401521)
230-101-000-02 (N6752401521)
Proof pressure check.
TSM or the last proof test.
To be carried out by the manufacturer or by an approved workshop.
NPT
AS 532 SC
05-20-00
2020.07.31 ATA 26 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 28-FUEL
28-10 STORAGE
28/10/00/000/000/015
Fuel tank
CMM 28.99.99 PO A 10 FH X 2 FH
PAGE 401
Each time after the component is installed.
Cleaning the filter element of optional fuel ice trap.
CLN
28/10/00/303/000/020
Fuel tank
MET 28.20.00.303 PO A 10 FH X 2 FH
Each time after the component is installed.
Cleaning the filter element.
CLN
28/10/00/407/000/010
Jet pump - Strainer
MET 28.10.00.407 PO A 10 FH X 2 FH
§ F.2
§ F.3
Each time after the component is installed.
Cleaning.
CLN
28/10/00/000/000/020
Fuel tank
MTC 20.08.06.401 A 3M X 9D
Tropical and damp atmosphere
Check and maintenance.
DI
28/10/00/407/000/000
Jet pump - Strainer
MET 28.10.00.407 A 1000 FH X 100 FH
§ F.2 // 4Y X 146 D
§ F.3
Cleaning.
CLN
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/10/00/601/000/000
Fuel tank
MET 28.10.00.601 A 2Y X 73 D
Succinct check.
DI
28/10/00/602/000/000
Fuel tank
MET 28.10.00.602 A 7500 FH X 300 FH
Detailed check with removal of all fuel cells.
DI
28/10/00/603/000/000
Air vents
MET 28.10.00.603 A 6Y X 180 D
Check.
DI
28/11/00/501/000/000
Pressure refuelling system
MET 28.11.00.501 A 7500 FH X 300 FH
PRE MOD 0725854
System test and check.
FT|DI
28/11/00/501/000/005
Pressure refuelling system
MET 28.11.00.502 A 7500 FH X 300 FH
POST MOD 0725854
System test and check.
FT|DI
28/11/00/501/000/010
Pressure refuelling system
MET 28.11.00.504 A 7500 FH X 300 FH
POST MOD 0726647
System test and check.
FT|DI
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/20/00/000/000/000
Transfer pump
CMM 28.11.01 A 3000 FH X 300 FH
§ CHECK
§ DISASSEMBLY
Slip ring and brush checks and replacement of the seals and of the bearings.
DI|DS
28/20/00/000/000/020
Filter - -45 °C filter element
CMM 28.22.98 A 1000 FH X 100 FH
Cleaning.
CLN
28/20/00/303/000/010
Filter - Filter element
MET 28.20.00.303 A 1000 FH X 100 FH
PRE MOD 0725996
Cleaning.
CLN
28/20/00/520/603/000
Tightness check valves
MET 28.20.00.603 A 7500 FH X 300 FH
// 15 Y X 180 D
Check.
DI
28/20/00/601/000/000
Fuel system
MET 28.20.00.602 A 7500 FH X 300 FH
Check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/40/00/502/000/000
Transfer system
MET 28.40.00.502 A 7500 FH X 300 FH
PRE MOD 0725730
Test.
FT
28/40/00/504/000/000
Fuel shut-off valve
MET 28.40.00.504 A 1500 FH X 150 FH
// 4Y X 146 D
PRE MOD 0725730
Test.
FT
28/40/00/505/000/000
Filter clogging indicating system
MET 28.40.00.505 A 2Y X 73 D
PRE MOD 0725730
Test.
FT
28/40/00/506/000/000
Fuel low level indication
MET 28.40.00.506 A 6Y X 180 D
PRE MOD 0725730
Functional test.
FT
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/40/01/520/505/000
Transfer system
MET 28.40.01.505 A 7500 FH X 300 FH
POST MOD 0725730
Test.
FT
28/40/01/520/506/000
Fuel shut-off valve
MET 28.40.01.506 A 1500 FH X 150 FH
// 4Y X 146 D
POST MOD 0725730
Test.
FT
28/40/01/520/507/000
Fuel low level indication
MET 28.40.01.507 A 6Y X 180 D
POST MOD 0725730
Functional test.
FT
28/40/01/520/508/000
Filter clogging indicating system
MET 28.40.01.508 A 2Y X 73 D
POST MOD 0725730
Test.
FT
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/91/01/401/000/010
External fuel tank (350 l x 2)
MET 28.91.01.401 A 6M X 18 D
§ H.4.a
Tropical and damp atmosphere
Greasing the bleed remote control system.
LUB
28/91/01/501/000/000
External fuel tank (350 l x 2) - Fuel level contactors
MET 28.91.01.501 A 7500 FH X 300 FH
Test.
FT
28/91/01/601/000/000
External fuel tank (350 l x 2)
MET 28.91.01.601 A 500 FH X 50 FH
Equipment checks.
DI
28/91/02/601/000/000
Supplementary 600 l fuel tank
MET 28.91.02.601 A 500 FH X 50 FH
Equipment checks.
DI
28/92/00/602/000/000
Ferry tank
MET 28.92.00.602 A 8Y X 180 D
Bonding check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
28/93/00/601/000/000
Preclogging alarm
MET 28.93.00.601 A 7500 FH X 300 FH
Check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 28 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
29/00/00/303/000/000
Hydraulic system
MET 29.00.00.306 A 3000 FH X 0A
MET 29.00.01.306 // 4Y X 0A
Card 29.00.00.306 PRE MOD 0723817.
Card 29.00.01.306 POST MOD 0723817.
Drain and fill.
DRN
29/00/00/303/000/010
Hydraulic system
MET 29.00.00.306 A 2Y X 0A
MET 29.00.01.306
Salt-laden atmosphere
Card 29.00.00.306 PRE MOD 0723817.
Card 29.00.01.306 POST MOD 0723817.
Drain and fill.
DRN
29/00/00/307/000/000
Accumulator
MET 29.00.00.307 A 2Y X 73 D
MET 29.00.01.307
Card 29.00.00.307 PRE MOD 0723817.
Card 29.00.01.307 POST MOD 0723817.
Charging pressure check.
SVC
AS 532 SC
05-20-00
2021.07.28 ATA 29 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
29/00/00/501/000/000
Hydraulic system
MET 29.00.00.501 A 7500 FH X 300 FH
MET 29.00.01.501
Card 29.00.00.501 PRE MOD 0723817.
Card 29.00.01.501 POST MOD 0723817.
System overpressure testing.
FT
29/00/00/520/605/100
Hydraulic system - Hose
MET 29.10.00.605 A 8Y X 180 D
§ F.3
MET 29.10.01.605
§ F.3
WC 29.10.00.605 PRE MOD 0723817.
WC 29.10.01.605 POST MOD 0723817.
Removal for replacement.
RS
AS 532 SC
05-20-00
2021.07.28 ATA 29 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
29/10/00/403/000/030
Hydraulic pump
MET 29.10.00.403 PO A 1200 FH X 120 FH
MET 29.10.01.403
C24160026 (704A44320014)
C24160026-1 (-)
After the introduction to service of a new, overhauled or repaired component.
Card 29.10.00.403 PRE MOD 0723817.
Card 29.10.01.403 POST MOD 0723817.
Return the pumps to the manufacturer to check the pads.
DI
29/10/00/601/000/000
Main hydraulic power system
MET 29.10.00.601 A 6Y X 180 D
EXC. § F.3.b
EXC. § G.3.b
EXC. § H.6
MET 29.10.01.601
EXC. § F.3.b
EXC. § G.3.b
EXC. § H.5
Card 29.10.00.601 PRE MOD 0723817.
Card 29.10.01.601 POST MOD 0723817.
Check.
DI
29/10/00/601/000/005
Main hydraulic power system - Hydraulic tank
MET 29.10.00.601 A 7500 FH X 300 FH
§ F.3.b // 15 Y X 180 D
§ G.3.b
MET 29.10.01.601
§ F.3.b
§ G.3.b
Card 29.10.00.601 PRE MOD 0723817
Card 29.10.01.601 POST MOD 0723817
Internal check.
DI
29/10/00/603/000/000
Hydraulic pump - Drive shaft
MET 29.10.00.603 A 500 FH X 50 FH
MET 29.10.01.603
Card 29.10.00.603 PRE MOD 0723817.
Card 29.10.01.603 POST MOD 0723817.
Checks and greasing.
DI|LUB
AS 532 SC
05-20-00
2021.07.28 ATA 29 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
29/20/00/601/000/000
Parking brake accumulator
MET 29.20.00.601 A 2Y X 73 D
MET 29.20.01.601
Card 29.20.00.601 PRE MOD 0723817.
Card 29.20.01.601 POST MOD 0723817.
Inflation pressure check.
DI|SVC
29/20/00/602/000/000
Auxiliary hydraulic power system
MET 29.20.00.602 A 500 FH X 50 FH
MET 29.20.01.602 // 6Y X 180 D
Card 29.20.00.602 PRE MOD 0723817.
Card 29.20.01.602 POST MOD 0723817.
Emergency and utility system checks.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 29 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/20/00/000/000/010
Pneumatically actuated multi-purpose air intakes - Bullet
MET 30.21.00.602 A 1500 FH X 150 FH
Check.
DI
30/20/00/000/000/020
Pneumatically actuated multi-purpose air intakes
MET 30.21.00.601 A 500 FH X 50 FH
// 2Y X 73 D
System check.
DI
30/20/00/000/000/030
Pneumatically actuated multi-purpose air intakes - Bullet reinforcement
MET 30.21.00.601 A 50 FH X 5 FH
§ F.2 // 2M X 6D
Check for corrosion.
Damage level 2.
PMP not applicable = TSI.
DI
30/20/00/000/000/035
Pneumatically actuated multi-purpose air intakes - Bullet reinforcement
MET 30.21.00.601 A 6M X 18 D
§ F.2
Check for corrosion.
Damage level 1.
PMP not applicable = TSI.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 30 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/20/00/000/000/040
Electrically actuated multi-purpose air intakes
MET 30.21.01.601 A 500 FH X 50 FH
// 2Y X 73 D
System check.
DI
30/20/00/000/000/050
Electrically actuated multi-purpose air intakes - Bullet seal
MET 30.21.01.602 A 1000 FH X 100 FH
Check.
DI
30/20/00/000/000/060
Multi-purpose air intakes
MET 30.21.01.601 A 500 FH X 50 FH
§ F.4
Borescope inspection of the MPAI.
CLN
30/20/00/501/000/000
Heating mats
MET 30.20.00.501 A 500 FH X 50 FH
Electric system test.
FT
30/20/00/601/000/005
Heating mats
MET 30.20.00.601 A 500 FH X 50 FH
§ F.4.b // 2Y X 73 D
§ F.4.d
PRE MOD 332P083234 & PRE MOD 0726540
Wiring check and insulation test.
DI
30/20/00/601/000/010
Heating mats
MET 30.20.00.601 A 500 FH X 50 FH
§ F.4.b // 2Y X 73 D
§ F.4.e
POST MOD 332P083234 & PRE MOD 0726540
Wiring check and insulation test.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 30 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/20/00/601/000/015
Heating mats
MET 30.20.00.601 A 500 FH X 50 FH
§ F.4.c // 2Y X 73 D
POST MOD 0726540
Visual check of wiring removable part.
VC
30/20/00/601/000/020
Air intakes
MET 30.20.00.601 A 50 FH X 5 FH
EXC. § F.4.b
EXC. § F.4.c
EXC. § F.4.d
EXC. § F.4.e
Detailed check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 30 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/60/00/403/000/038
TRH and MRH harnesses
MET 30.60.00.601 A A ALF X 0A
§G
EXC. § G.2.b
Check.
DI
30/60/00/501/000/000
Rotor de-icing system
MET 30.60.00.501 A 3000 FH X 300 FH
System test.
FT
30/60/00/601/000/000
Rotor de-icing system
MET 30.60.00.601 A 500 FH X 50 FH
EXC. § H.1
EXC. § I
System check.
DI
30/60/00/601/000/010
Rotor de-icing system
MET 30.60.00.601 A 50 FH X 5 FH
§ G.2.b
Manual check.
DI
30/60/00/601/000/030
MRH - Rotating slip ring
MET 30.60.00.601 A 1500 FH X 150 FH
§ H.1
Maintenance.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 30 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/60/00/603/000/000
Rotor de-icing system
MET 30.60.00.603 A 500 FH X 50 FH
§ G.1
System condition check.
DI
30/60/00/603/000/010
Rotor de-icing system
MET 30.60.00.603 A 1000 FH X 100 FH
§ G.2
System condition check.
DI
30-80 DETECTION
30/80/00/601/000/000
Ice detection system
MET 30.80.00.601 A 2Y X 73 D
MET 30.80.02.601
System check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 30 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
31-32 RECORDING
31/32/00/000/000/000
Flight data recorder
CMM 31.20.02.1 A 250 FH X 25 FH
SFIM A213.
Motor overhaul.
DI
31/32/00/000/000/010
Flight data recorder
CMM 31.20.02.1 A 1Y X 36 D
SFIM A213.
Setting mechanism calibration by the manufacturer.
DI
31/32/00/000/000/020
Flight data recorder
CMM 31.20.02.1 A 50 FH X 5 FH
SFIM A213.
Spool replacement.
DI
31/32/00/000/000/030
Flight data recorder
CMM 31.20.04 A 2000 FH X 200 FH
// 1Y X 36 D
ENERTEC type PE6010.
System tests and checks.
FT|DI
31/32/01/501/000/000
Flight data recorder
CMM 31.20.02.1
SFIM A213.
Sensor calibration, calibration curve after the recorder is returned from the manufacturer or after replacing a sensor.
DI
31/32/01/601/000/000
Flight data recorder
MET 31.32.01.601 A 8D X 0A
§G
SFIM A213.
Winding elapsed time indicator.
DI
AS 532 SC
05-20-00
2015.10.15 ATA 31 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
31/32/04/501/000/000
Parameters recorder
MET 31.32.04.501 A 2000 FH X 200 FH
MET 31.32.04.601 // 1Y X 36 D
PLESSEY-SUNSTRAND
Equipment tests and checks.
DI
AS 532 SC
05-20-00
2015.10.15 ATA 31 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/00/00/000/000/010
Landing gear - Wheel
MET 32.00.00.302 A 1Y X 36 D
§ F.2, F.4 // 600 LC X 60 LC
MET 32.00.01.302
§ F.2, F.4
Card 32.00.00.302 PRE MOD 0723817.
Card 32.00.01.302 POST MOD 0723817.
Bearing lubrication.
LUB
32/12/00/000/000/130
Spindle and fitting
MET 32.10.00.602 A 3750 FH X 300 FH
MET 32.10.01.602 // 6Y X 180 D
Card 32.10.00.602 PRE MOD 0723817.
Card 32.10.01.602 POST MOD 0723817.
Checks.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/22/00/000/000/100
Attachment
MET 32.20.00.602 A 3750 FH X 300 FH
MET 32.20.01.602 // 6Y X 180 D
Card 32.20.00.602 PRE MOD 0723817.
Card 32.20.01.602 POST MOD 0723817.
Checks.
DI
32/30/00/502/000/010
Extension and retraction
MET 32.30.01.502 A 7500 FH X 300 FH
POST MOD 0723817
Safety tests.
FT
32/30/00/502/000/015
Extension and retraction
MET 32.30.01.502 A 2Y X 73 D
§ F.1, F.2
POST MOD 0723817
Safety tests.
FT
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/30/00/502/000/020
Extension and retraction
MET 32.30.00.502 A 2Y X 73 D
PRE MOD 0723817
Safety tests.
FT
32/30/00/503/000/000
Landing gear unit emergency control
MET 32.30.00.503 A 7500 FH X 300 FH
MET 32.30.01.503
Card 32.30.00.503 PRE MOD 0723817.
Card 32.30.01.503 POST MOD 0723817.
Adjustment.
RIG
32/30/00/601/000/000
Extension and retraction
MET 32.30.00.601 A 7500 FH X 300 FH
MET 32.30.01.601
Card 32.30.00.601 PRE MOD 0723817.
Card 32.30.01.601 POST MOD 0723817.
Landing gear extension/retraction system checks.
DI
32/30/00/601/000/010
TELEFLEX control
MET 32.30.00.601 A 500 FH X 50 FH
§H
MET 32.30.01.601
§G
Card 32.30.00.601 PRE MOD 0723817.
Card 32.30.01.601 POST MOD 0723817.
Greasing without removal.
LUB
32/30/00/601/000/015
Detector box
MET 32.30.00.601 A 3000 FH X 300 FH
§G // 6Y X 180 D
PRE MOD 0723817
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/30/00/601/000/020
Detector box
MET 32.30.00.601 A 3000 FH X 300 FH
§G // 3Y X 109 D
PRE MOD 0723817
Tropical and damp atmosphere
Salt-laden atmosphere
Check.
DI
32/30/00/602/000/000
Hydraulic generator, L/G
MET 32.30.00.602 A 500 FH X 50 FH
MET 32.30.01.602
97154-120 (704A44333030)
97154-121 (704A44333074)
Check.
WC 32.30.00.602 PRE MOD 0723817.
WC 32.30.01.602 POST MOD 0723817.
GVI
32/30/01/501/000/000
Extension and retraction
MET 32.30.00.501 A 7500 FH X 300 FH
MET 32.30.01.501 // 3000 LC X 300 LC
WC 32.30.00.501 PRE MOD 0723817,
WC 32.30.01.501 POST MOD 0723817.
Extension/retraction tests.
FT
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/40/00/408/000/000
Main landing gear - Wheels
MET 32.40.00.606 A 2Y X 73 D
MET 32.40.01.606 // 1200 LC X 120 LC
WC 32.40.00.606 PRE MOD 0723817
WC 32.40.01.606 POST MOD 0723817
Check - Maintenance.
DI
32/40/00/502/000/000
Parking brake
MET 32.40.00.502 A 7500 FH X 300 FH
MET 32.40.01.502
WC 32.40.00.502 PRE MOD 0723817.
WC 32.40.01.502 POST MOD 0723817.
Control adjustment.
RIG
32/40/00/602/000/000
Wheel and brake
MET 32.40.00.602 A 7500 FH X 300 FH
MET 32.40.01.602
Card 32.40.00.602 PRE MOD 0723817.
Card 32.40.01.602 POST MOD 0723817.
Wheel braking system checks.
DI
32/40/00/603/000/000
Parking brake
MET 32.40.00.603 A 7500 FH X 300 FH
MET 32.40.01.603
Card 32.40.00.603 PRE MOD 0723817.
Card 32.40.01.603 POST MOD 0723817.
Torque/pressure checks.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
32/50/00/601/000/010
TELEFLEX control
MET 32.50.00.601 A 500 FH X 50 FH
§G
Greasing without removal.
LUB
AS 532 SC
05-20-00
2021.07.28 ATA 32 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 33-LIGHTS
33/20/00/601/000/000
Neon tube
MET 33.20.00.601 A 500 FH X 50 FH
Before SB 33.00.03.
Check.
Fitted with transformer-rectifier MP/N TR992-7.
DI
33/20/03/201/000/000
Sealed ordinance light
MET 33.20.03.201 A 3000 FH X 300 FH
§G
Equipment maintenance.
DI
33/20/03/201/000/010
Sealed ordinance light
MET 33.20.03.201 A 500 FH X 50 FH
§F
MET 33.20.03.601
Equipment maintenance.
DI
AS 532 SC
05-20-00
2019.06.07 ATA 33 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
33/43/00/000/000/010
Landing light
CMM 33.49.19 A 1Y X 36 D
4202104 (704A46820019)
4360404 (704A46820038)
Removal of the light and appearance check of the mechanical parts without disassembly.
External cleaning of the light.
Lubrication of exposed meshing parts.
DI|CLN|LUB
33/43/00/000/000/016
Landing light
CMM 33.41.74 A 1Y X 36 D
4502411 (704A46820040)
Removal of the light and appearance check of the mechanical parts without disassembly.
External cleaning of the light.
Lubrication of exposed meshing parts.
DI|CLN|LUB
AS 532 SC
05-20-00
2019.06.07 ATA 33 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
33/43/00/000/000/017
Landing light
CMM 33.45.97 A 1Y X 36 D
4292187 (704A46820029)
Removal of the light and appearance check of the mechanical parts without disassembly.
External cleaning of the light.
Lubrication of exposed meshing parts.
DI|CLN|LUB
33/43/00/000/000/020
Light
CMM 33.40.01 A 2000 FH X 200 FH
// 4Y X 146 D
PE0600-3 (N6784311100)
PE0600-3A (-)
Check with removal.
DI
33/43/00/000/000/030
Landing light
CMM 33.41.74 A 2000 FH X 200 FH
// 4Y X 146 D
4502411 (704A46820040)
Check with removal.
DI
33/43/00/000/000/035
Landing light
CMM 33.45.97 A 2000 FH X 200 FH
// 4Y X 146 D
4292187 (704A46820029)
Check with removal.
DI
33/43/00/000/000/040
Landing light
CMM 33.49.19 A 2000 FH X 200 FH
4202104 (704A46820019)
4360404 (704A46820038)
Check with removal.
DI
AS 532 SC
05-20-00
2019.06.07 ATA 33 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
33/45/03/000/000/026
Searchlight
MET 33.45.03.601 A 500 FH X 50 FH
§ F.1.b
SPECTROLAB SX 16
Check.
DI
33/45/03/000/000/030
Searchlight - Gimbal
MET 33.45.03.602 A 300 FH X 30 FH
SPECTROLAB SX 16
Check.
DI
33/45/03/000/000/035
Searchlight - Fan
CMM 33.45.96 A 500 FH X 50 FH
SPECTROLAB SX 16
Check.
DI
33/45/03/000/000/040
Searchlight - Junction box
CMM 33.45.96 A 500 FH X 50 FH
SPECTROLAB SX 16
Check.
DI
33/45/03/501/000/000
Searchlight
MET 33.45.03.501 A 500 FH X 50 FH
SPECTROLAB SX 16
Equipment test.
FT
AS 532 SC
05-20-00
2019.06.07 ATA 33 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 34-NAVIGATION
34/11/00/520/601/100
Air data system
MET 34.11.00.601 A 500 FH X 50 FH
// 2Y X 73 D
PRE MOD 0726644
System check.
DI
34/21/00/503/000/000
Gyromagnetic compass
MET 34.21.06.503 A 6Y X 180 D
MET 34.21.06.504
MET 34.21.08.503
Compensation on the ground.
aircraft equipped with gyromagnetic compass and navigation computer.
FT
34/21/00/601/000/000
Gyromagnetic compass
MET 34.21.06.601 A 6Y X 180 D
MET 34.21.08.601
Equipment checks.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 34 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
34/23/00/601/000/000
Standby magnetic compass
MET 34.23.00.601 A 7500 FH X 300 FH
// 15 Y X 180 D
Check.
VC
34-42 RADAR
34/42/07/503/000/000
Radar 1400
MET 34.42.07.503 A 7500 FH X 300 FH
// 12 Y X 180 D
Antenna mechanism adjustment and testing.
RIG|FT
34/42/07/601/000/005
Radar 1400
MET 34.42.07.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 34 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
34/42/15/601/000/000
RDN 85 doppler radar
MET 34.42.15.601 A 1Y X 36 D
Salt-laden atmosphere
Check of installation with disassembly of antenna.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 34 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 35-OXYGEN
35/30/00/000/000/010
Oxygen mask
MET 35.10.00.601 A 2Y X 73 D
§ F.2
10100 (704A36240004)
Condition check.
GVI
35/30/00/000/000/025
Oxygen cylinder with SCOTT regulator
A 5Y X 0A
5600-2C1BX0K (-)
Re-test of bottles.
TSM or the last proof test.
The bottle must be sent to the manufacturer or the approved repairer equipped with its regulator.
NPT
AS 532 SC
05-20-00
2015.10.15 ATA 35 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 36-PNEUMATIC
36/10/00/000/000/017
Filter
MET 36.00.00.202 A 150 FH X 15 FH
461A6-2 (704A34622006)
461A6-3 (704A34622007)
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
Maintenance.
DI|CLN
36/10/00/000/000/020
Pneumatic system
MET 36.00.00.601 A 1500 FH X 150 FH
Check.
DI
36/10/00/000/000/025
Filter
MET 36.00.00.203 A 150 FH X 15 FH
217A01 (704A34622007)
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
Maintenance.
DI|CLN
36/10/00/000/000/030
Double check valve
CMM 36.19.99 A 7500 FH X 300 FH
// 15 Y X 180 D
994C32-11 (704A32113024)
Check.
DI
AS 532 SC
05-20-00
2014.01.09 ATA 36 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
AS 532 SC
05-20-00
2014.01.09 ATA 36 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
AS 532 SC
05-20-00
2013.01.10 ATA 39 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
45/11/00/000/000/030
EUROHUMS - Recorder
CMM 31.32.89 A 2500 FH X 250 FH
// 1Y X 36 D
D51508 (704A49430007)
Cleaning and inspection.
DI|CLN
45/11/00/000/000/040
EUROHUMS - Recorder
MET 45.11.02.513 A A BFF X 0A
§ F.1
§ F.2
Ground test.
FT
45/11/02/000/000/000
EUROHUMS
MET 45.11.02.533 A 3750 FH X 300 FH
// 3Y X 109 D
Check of the accelerometer acquisition channel of dynamic parts.
FT
45/11/02/000/000/010
EUROHUMS
MET 45.11.02.533 A 2Y X 73 D
Check of the accelerometer acquisition channel of engines.
FT
45/11/02/000/000/030
EUROHUMS - CVFDR recorder
CMM 23.70.48 A 1Y X 36 D
980-6021-032 (704A45381025)
Audio record level and quality check.
FT
AS 532 SC
05-20-00
2017.07.10 ATA 45 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
45/11/02/000/000/040
EUROHUMS - CVFDR recorder
CMM 31.32.90 A 1Y X 36 D
D51521-010-112 (704A45381021)
Audio record level and quality check.
FT
45/11/02/000/000/050
EUROHUMS - CVFDR recorder
CMM 31.32.90 A 6Y X 180 D
D51521-010-112 (704A45381021)
Check of the section protected against accidents.
FT
45/11/02/000/000/060
EUROHUMS - CVFDR recorder
MET 45.11.02.531 A 1Y X 36 D
§F
980-6021-032 (704A45381025)
D51521-010-112 (704A45381021)
Check of the FDR recorder playback.
FT
45/11/02/000/000/070
EUROHUMS - CVFDR recorder
MET 45.11.02.515 A 6M X 18 D
980-6021-032 (704A45381025)
D51521-010-112 (704A45381021)
Test of the CVR erase function.
FT
45/11/02/000/000/080
EUROHUMS - CVFDR recorder
MET 45.11.02.513 A 6M X 18 D
980-6021-032 (704A45381025)
D51521-010-112 (704A45381021)
Test of the pilot, copilot and CVR area microphones.
FT
AS 532 SC
05-20-00
2017.07.10 ATA 45 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 46-WEAPONS
46-00 WEAPONS
46/00/05/520/601/100
Ballistic protections – Crew doors and seats
MET 46.00.05.602 A 2Y X 73 D
120001 (704A31651028)
120002 (704A41120200)
120003 (704A41120201)
120005 (704A41120202)
120007 (704A41120203)
120008 (704A31651029)
120009 (704A41120220)
Detailed inspection.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 46 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
47/50/00/301/000/000
FLIR STAR SAFIRE III
MET 47.50.09.301 A 2M X 6D
Normal climatic conditions
Drain/fill netrogen.
Time cumulated of presence on aircraft.
SVC
47/50/00/301/000/010
FLIR STAR SAFIRE III
MET 47.50.09.301 A 1M X 3D
Tropical and damp atmosphere
Drain/fill netrogen.
Time cumulated of presence on aircraft.
SVC
47/50/00/601/000/000
FLIR STAR SAFIRE III - Indicator
MET 47.50.09.601 A 1M X 3D
Inspection.
Time cumulated of presence on aircraft.
GVI
AS 532 SC
05-20-00
2015.04.16 ATA 47 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 52-DOORS
52/11/01/601/000/005
Side plug door
MET 52.11.01.601 A 100 FH X 10 FH
§ I.1
PRE MOD 0725366 // PRE MOD 0723667.
Jettison tests.
DI
52/11/01/601/000/008
Side plug door
MET 52.11.01.502 A 250 FH X 25 FH
§ F.2
POST MOD 0725366 // POST MOD 0723667.
Jettison tests.
DI
52/11/01/601/000/010
Side plug door
MET 52.11.01.601 A 500 FH X 50 FH
MET 52.11.01.602 // 2Y X 73 D
Card 52.11.01.601 PRE MOD 0725366.
Card 52.11.01.602 POST MOD 0725366.
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 52 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
52/11/01/601/000/020
Side plug door
MET 52.11.01.601 A 50 FH X 5 FH
§ F.1.a
MET 52.11.01.602
§ F.1.a
Card 52.11.01.601 PRE MOD 0725366.
Card 52.11.01.602 POST MOD 0725366.
Check.
GVI
52/11/01/601/000/040
Side plug door
MET 52.11.01.601 A 1Y X 36 D
§ F.3.a
PRE MOD 0725366
Check.
CLN|GVI
52/11/01/602/000/000
Side plug door
MET 52.11.01.502 A 250 FH X 25 FH
MET 52.11.01.602
PRE MOD 0726176 & PRE MOD 0726413. POST MOD 0723667 // POST MOD 0725366.
Check.
DI
52/11/01/602/000/010
Side plug door
MET 52.11.01.602 A 1Y X 36 D
§ F.3.a
POST MOD 0725366
Check.
CLN|GVI
AS 532 SC
05-20-00
2021.07.28 ATA 52 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
52-14 DOORS
52/14/00/601/000/000
Rear stairway door
MET 52.14.00.601 A 500 FH X 50 FH
// 4Y X 146 D
System check.
DI
52/14/02/601/000/000
Double-wing sliding door
MET 52.14.02.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 52 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 53-FUSELAGE
53-00 FUSELAGE
53/00/00/000/000/000
Bearing blocks - Mounts
MET 53.10.00.608 A 500 FH X 50 FH
§ K.2
MET 53.10.00.609
§ F.2
PRE MOD 0723972
Monitoring the bearing block mount attachments on the transmission deck angle,
intermediate structure and tail boom.
If no loose rivets: Check every 500 FH.
If one loose rivet: Check every 50 FH.
If more rivets are found loose: repair during the next 50 FH inspection but check during every ALF check.
DI
53/00/00/000/000/010
Fuselage
MET 05.55.00.301 A 6M X 18 D
§ F.1.c.3
Tropical and damp atmosphere
Salt-laden atmosphere
Check anti-corrosion beads.
GVI
53/00/00/000/000/030
Fuselage
MTC 20.04.01.403 A 7D X 0A
Salt-laden atmosphere
Cleaning.
CLN
53/00/00/000/000/035
Fuselage
MTC 20.04.01.403 A A ALF X 0A
Salt-laden atmosphere
Washing and drying.
CLN
53/00/00/000/000/040
Structure
MET 53.10.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/00/00/000/000/045
Aft structure - Mounts
MET 53.10.00.609 A 1500 FH X 150 FH
§ F.2
Check.
DI
53/00/00/000/000/050
Structure
MET 53.10.00.607 A 7500 FH X 300 FH
Check.
DI
53/00/00/000/000/060
Structure
MET 53.10.00.607 A 12 Y X 180 D
Check.
CAUTION: ageing task.
DI
53/10/00/000/000/010
Aft structure
MET 53.10.00.401 A 500 FH X 50 FH
§H
Tail boom-to-aft structure attachment tightening torque check.
TCK
53/10/00/000/000/030
Aft structure
MET 53.10.00.609 A 12 Y X 180 D
Check.
CAUTION: ageing task.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/10/00/402/000/000
Primary structure - Attachment
MET 53.10.00.402 A 6Y X 180 D
§ G.2
Check.
DI
53/10/00/603/000/000
Transmission deck
MET 53.10.00.603 A 500 FH X 50 FH
Check.
DI
53/10/00/603/000/005
Transmission deck
MET 53.10.00.603 A 2M X 6D
Helicopter based aboard a ship.
Check.
DI
53/10/00/603/000/010
Transmission deck
MET 53.10.00.603 A 12 Y X 180 D
Check.
CAUTION: ageing task.
DI
53/10/00/605/000/010
Canopy structure
MET 53.10.00.605 A 50 FH X 0A
§ F.2
Operation to be carried out as from 3750 hours.
Check of the lateral posts.
GVI
53/10/00/606/000/000
Tail boom-to-frame 9000
MET 53.10.00.606 A 500 FH X 50 FH
§ H.1, H.2
PRE MOD 0723929
Or kit 332A09-0182/0183
Junction check. aircraft that have logged less than 2000 FH.
If the cracks correspond to the criteria specified in § H.1.a, H.2.a, H.1.b.3, H.2.b.3: repair
to be performed within the next 50 FH.
If the cracks correspond to the criteria specified in § H.1.b.1, H.2.b.1: repair to be performed within the next 250 FH.
GVI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/10/00/606/000/010
Aft structure
MET 53.10.00.606 A 7500 FH X 300 FH
§ G.2.b
§ G.2.c
Check.
DI
53/10/00/606/000/020
Tail boom-to-frame 9000
MET 53.10.00.606 A 250 FH X 25 FH
§ H.1, H.2
PRE MOD 0723929
Or kit 332A09-0182/0183
Junction check. aircraft that have logged more than 2000 FH.
If the cracks correspond to the criteria specified in § H.1.a, H.2.a, H.1.b.3, H.2.b.3: repair
to be performed within the next 50 FH.
If the cracks correspond to the criteria specified in § H.1.b.1, H.2.b.1: repair to be performed within the next 250 FH.
GVI
53/10/00/606/000/025
Tail boom-to-frame 9000
MET 53.10.00.606 A 500 FH X 50 FH
§ H.3
PRE MOD 0723929
Or kit 332A09-0182/0183.
aircraft that have logged more than 3000 FH.
GVI
53/10/00/606/000/030
Aft structure
MET 53.10.00.606 A 500 FH X 50 FH
§F // 2Y X 73 D
Check.
DI
53/10/00/610/000/000
Lower structure
MET 53.10.00.610 A 7500 FH X 300 FH
Detail check of the bottom structure.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/10/00/610/000/005
Bottom structure - Fuel tank compartment
MET 53.10.00.610 A 6Y X 180 D
§ F.2
Detailed check with removal of covering panels.
First inspection: sounding of right longitudinal fuel tank compartment at 6 Y.
Second inspection: sounding of left longitudinal fuel tank compartment at 12 Y.
If corrosion is found, remove all the fuel tank lining panels.
DI
53/10/00/610/000/010
Lower structure
MET 53.10.00.610 A 12 Y X 180 D
§ F.1
Check.
CAUTION: ageing task.
DI
53/10/00/611/000/000
Tail boom-to-frame 9000
MET 53.10.00.611 A 550 FH X 55 FH
PRE MOD 0726313
For tail booms with more than 7500 FH, check the skin for cracks.
If cracks less than 150 mm are found, perform a monitoring check every 110 FH.
DI
53/10/00/612/000/000
Screws attaching the horizontal members Z1350 and frame X5295
MET 53.10.00.612 A 7500 FH X 300 FH
// 12 Y X 180 D
Readjustment of the tightening torque.
RTQ
53/20/00/000/000/005
Cabin floor
MET 53.10.00.602 A 2M X 6D
Helicopter based aboard a ship.
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/20/00/000/000/010
Cockpit floor
MET 53.10.00.604 A 500 FH X 50 FH
// 4Y X 146 D
Check.
DI
53/20/00/000/000/015
Cockpit floor
MET 53.10.00.604 A 2M X 6D
Helicopter based aboard a ship.
Check.
DI
53/20/00/601/000/000
Secondary structure
MET 53.20.00.601 A 7500 FH X 300 FH
Check.
DI
53/20/00/602/000/000
Self-sealing check valves
MET 53.20.00.602 A 100 FH X 10 FH
POST MOD OP26382
Check.
DI
53/40/00/000/000/030
Forward structure - Mounts
MET 53.10.00.608 A 1500 FH X 150 FH
§ K.2
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/40/00/000/000/050
Forward structure
MET 53.10.00.608 A 7500 FH X 300 FH
EXC § F.2
Check of the fittings.
DI
53/40/00/000/000/070
Aft structure
MET 53.10.00.609 A 7500 FH X 300 FH
Check of the fittings.
DI
53/40/00/000/000/075
Forward structure - Attachment fitting and mounts
MET 53.10.00.608 A 7500 FH X 300 FH
§ F.2 // 12 Y X 180 D
Check.
DI
53/50/00/601/000/030
Engine and sliding cowlings
MET 53.50.00.601 PO A 50 FH X 5 FH
§ G.2, G.3
After the introduction to service of a new, overhauled or repaired component,
After installation of a component originating from another helicopter.
Locking mechanism check.
DI
53/50/00/301/000/000
Engine cowling - Hinge support
MET 53.50.00.301 A 2Y X 73 D
Cleaning, rinsing.
CLN
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/50/00/501/000/010
Air intake fairing
MET 53.50.00.501 A 7500 FH X 300 FH
Locking adjustment.
DI
53/50/00/502/000/010
Engine cowlings
MET 53.50.00.502 A 7500 FH X 300 FH
Locking adjustment.
DI
53/50/00/520/602/020
Aft structure - Fairing
MET 53.50.00.602 A 1200 FH X 120 FH
§ F.9
332A24-0329-0101 (-)
POST MOD 0726860
Check.
DI
53/50/00/520/602/100
IGB fairing – Fixation bracket
MET 53.50.00.602 A 100 FH X 10 FH
§ F.10
Check.
DI
53/50/00/601/000/000
Cowlings
MET 53.50.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Checks of the fixed and moving cowlings.
DI
53/50/00/601/000/040
Sliding cowling
MET 53.50.00.601 A 100 FH X 0A
§ F.5.e
PRE MOD 0725429 & POST MOD 0723770
Locking system check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 8
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/50/00/602/000/000
Aft structure - Fairing
MET 53.50.00.602 A 250 FH X 25 FH
EXC. § F.3
EXC. § F.8
EXC. § F.9
Inspection.
DI
53/50/00/602/000/005
Aft structure - IGB fairing
MET 53.50.00.602 A 500 FH X 50 FH
§ F.3
Check.
CLN|GVI
53/50/00/602/000/010
Aft structure - Fairing
MET 53.50.00.602 A 150 FH X 15 FH
§ F.8
PRE MOD 0726860
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 53 Page 9
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 55-STABILIZER
55/10/00/000/000/010
Shackle
MET 55.00.00.601 A 50 FH X 5 FH
§ F.7
PRE MOD 0726233.
Check.
GVI
55/10/00/000/000/015
Stabilizer - Attachment and tube
MET 55.00.00.601 A 500 FH X 50 FH
§ I.1, I.2, I.3 // 2Y X 73 D
POST MOD 0726233.
Check.
DI
55/10/00/000/000/020
Stabilizer - Attachment and tube
MET 55.00.00.602 A 8Y X 180 D
EXC. § F
Check.
DI
55/10/00/000/000/060
Horizontal stabilizer
MET 55.00.00.401 A 1000 FH X 100 FH
§G
Stabilizer-to-tail boom attachment tightening torque load check.
TCK
AS 532 SC
05-20-00
2018.08.17 ATA 55 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
55/10/00/000/000/100
Horizontal stabilizer
MET 55.00.00.601 A 500 FH X 50 FH
// 2Y X 73 D
PRE MOD 0726233.
Check.
DI
55/10/00/000/000/110
Stabilizer - Attachment and tube
MET 55.00.00.602 A 4500 FH X 300 FH
EXC. § G // 6Y X 180 D
Check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 55 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 56-WINDOWS
56-10 COCKPIT
56/10/00/000/000/000
Cockpit windows
MET 56.10.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
56-20 WINDOWS
56/20/00/000/000/000
Emergency exit in the aft hatch
MET 52.22.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
56/20/00/000/000/015
Cabin window
MET 56.20.00.601 A 500 FH X 50 FH
// 2Y X 73 D
Check.
DI
56/20/00/000/000/020
Emergency exit windows
MET 56.20.00.401 A 2Y X 73 D
Removal-installation for Jettison test.
DI
56/20/00/520/601/100
Window and emergency exit - Quick-release tape
MET 56.20.00.601 A 50 FH X 5 FH
§ F.2
PRE MOD 0728136
Check.
GVI
56/20/00/520/601/200
Window and emergency exit - Quick-release handle
MET 56.20.00.601 A 50 FH X 5 FH
§ F.3 // 1Y X 36 D
POST MOD 0728136
Check.
GVI
AS 532 SC
05-20-00
2021.07.28 ATA 56 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
AS 532 SC
05-20-00
2021.07.28 ATA 56 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/10/00/000/000/080
Main rotor blade
MET 62.10.00.603 PO A 50 FH X 5 FH
§ F.4
Check.
After replacing the balance weight mount stud, carry out a general check of the blade prior to the first
flight, then at 50 FH with removal of blade tip fairing and studs check.
If no deterioration is noted, return to the normal maintenance cycle.
DI
62/10/00/000/000/100
Blade tip fairing
MET 62.10.00.603 PO A 50 FH X 5 FH
§ F.9 & 100 FH X 10 FH
& 150 FH X 15 FH
& 200 FH X 20 FH
332A11-1262-XX (-)
After the introduction to service of a new, overhauled or repaired component.
Nickel bonding check.
DI
62/10/00/000/000/102
Blade tip fairing
MET 62.10.00.603 PO A 50 FH X 5 FH
§ F.9 & 200 FH X 20 FH
332A11-1263-XX (-)
332A11-1269-XX (-)
After the introduction to service of a new, overhauled or repaired component.
Inox bonding check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/10/00/000/000/002
Main rotor blade
MET 62.10.00.608 A 100 FH X 10 FH
332A11-0030-XX (-)
332A11-0032-XX (-)
Inspection of leading edge.
GVI
62/10/00/000/000/003
Main rotor blade
MET 62.10.00.607 A 10 FH X 2 FH
332A11-0030-XX (-)
332A11-0032-XX (-)
Check of the integrity of the leading edge protective titanium strip.
GVI
62/10/00/000/000/005
Main rotor blade
MET 62.10.00.607 A 50 FH X 5 FH
332A11-0022-00 (-)
332A11-0022-01 (-)
332A11-0022-02 (-)
332A11-0022-03 (-)
332A11-0022-04 (-)
332A11-0024-XX (-)
332A11-0025-XX (-)
Stainless steel leading edge protective strip integrity check.
GVI
62/10/00/000/000/054
Main rotor blade
MET 60.00.00.304 A 25 FH X 2 FH
Tropical and damp atmosphere
Salt-laden atmosphere
Cleaning.
CLN
62/10/00/000/000/090
Main rotor blade
MET 62.10.00.603 A 10 FH X 1 FH
Sand-laden and/or dust-laden atmosphere
Visual check for erosion.
In intensive operation in very sandy areas, all the necessary steps must be taken to ensure optimum
operation of the aircraft If necessary shorten the proposed inspection intervals.
GVI
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/10/00/000/000/115
Main rotor blade
MET 05.55.00.301 A 1Y X 36 D
§ F.1.e
Tropical and damp atmosphere
Salt-laden atmosphere
Protection of the blade tip components.
Applicable to the blades with no letter T after their serial number.
DI
62/10/00/000/000/117
Main rotor blade
MET 05.55.00.301 A 2Y X 73 D
§ F.1.e
Tropical and damp atmosphere
Salt-laden atmosphere
Protection of the blade tip components.
Applicable to the blades with letter T after their serial number.
DI
62/10/00/000/000/120
Main rotor blade
MET 62.10.00.603 A 500 FH X 50 FH
EXC. § F.4
Check without removing the blade tip fairing.
GVI
62/10/00/000/000/125
Main rotor blade
MET 62.10.00.603 A 2M X 6D
Helicopter based aboard a ship.
Check.
DI
62/10/00/000/000/130
Main rotor blade
MET 62.10.00.603 A 2Y X 73 D
Check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/35/00/000/000/075
MRH - Scissors, fixed
MET 62.35.00.407 PO A 3 FH X 7 FH
PRE MOD 0743046
Each time after the component is installed.
Attachment bolts tightening torque readjustment.
RTQ
62/35/00/000/100/000
Flared housing - Chip detector
MET 60.00.00.603 PO A 3 FH X 7 FH
After the introduction to service of a new, overhauled or repaired component.
Check.
DI
62/35/00/000/100/030
Flared housing - MGB upper cover
MET 62.35.00.601 PO A 50 FH X 5 FH
§ G.11.b & 100 FH X 10 FH
Each time after the component is installed.
Attachment bolts tightening torque load check.
TCK
62/35/00/000/300/000
Frequency adapter
MET 62.35.00.605 PO A 3 FH X 7 FH
§ F.2.a
Each time after the component is installed.
Attachment bolt nut tightening torque readjustment.
RTQ
62/35/00/000/300/005
MRH - Blade horn
MET 62.35.00.408 PO A 3 FH X 7 FH
Each time after the component is installed.
Attachment bolts tightening torque readjustment.
RTQ
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/35/00/601/000/020
Main rotor head / mast - Swash plate
MET 62.35.00.601 PO A 3 FH X 7 FH
§ H.3
Each time after the component is installed,
Greasing.
LUB
62/35/00/000/000/005
MRH
MET 60.00.00.302 A 500 FH X 50 FH
// 2Y X 73 D
Mineral oil change.
DRN
62/35/00/000/000/006
MRH
MET 60.00.00.302 A 500 FH X 50 FH
// 4Y X 146 D
Synthetic oil change.
DRN
62/35/00/000/000/008
MRH - Blade pin
MET 62.10.00.401 A 1M X 3D
Helicopter based aboard a ship.
Lubrication.
LUB
62/35/00/000/000/010
MRH - Blade pin
MET 62.10.00.401 A 6M X 18 D
Greasing.
LUB
62/35/00/000/000/020
MRH
MET 62.35.00.601 A 250 FH X 25 FH
§H
EXC. § H.5
Greasing.
LUB
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/35/00/000/000/025
MRH - Sleeve/spindle assembly
MET 62.35.00.601 A 500 FH X 50 FH
§ H.5
POST MOD 0743286
Greasing.
LUB
62/35/00/000/000/030
MRH
MET 62.35.00.601 A 500 FH X 50 FH
Check of the assembly.
DI
62/35/00/000/000/040
MRH
MET 62.35.00.601 A 1M X 3D
§H
Helicopter based aboard a ship.
Check and greasing.
DI|LUB
62/35/00/000/000/055
MRH
MET 62.35.00.604 A 2Y X 73 D
§H
Check the following for corrosion: flapping hinge pins MP/N 332A31-1380-03/04 and MP/N
332A31-1433-01 and the drag hinges MP/N 330A31-1390-20.
SDI
62/35/00/000/000/115
Main rotor head/Mast
MET 05.39.00.601 A 4Y X 146 D
§ F.1
Tropical and damp atmosphere
Salt-laden atmosphere
Detailed check.
Initial compliance at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 4 Y.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
62/35/00/000/000/125
Main rotor head/Mast
MET 05.39.00.601 A 6Y X 180 D
§ F.1
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 6 Y.
DI
62/35/00/000/100/010
Main rotor shaft - Chip detector
MET 60.00.00.603 A 100 FH X 10 FH
§ F.2
Check.
DI
62/35/00/000/300/060
Frequency adapter - Small swivel bearing
MET 62.35.00.601 A 50 FH X 5 FH
§ G.5.d
Checking radial play.
DI
62/35/00/000/300/070
Frequency adapter
MET 62.35.00.605 A 500 FH X 50 FH
§ F.2.b
Tightening torque load check.
TCK
62/35/00/520/601/018
MRH - Blade pin
MET 62.35.00.601 A 500 FH X 50 FH
§ G.7.b
332A31-2123-00 (-)
POST MOD 0743293
MARVAL X12.
Check.
DI
AS 532 SC
05-20-00
2018.08.17 ATA 62 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/10/00/000/000/120
Engine-to-MGB coupling
MET 05.39.00.601 A 6Y X 180 D
§ F.3
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation
(startup), last Overhaul then every 6 Y.
DI
63/10/00/601/000/000
Engine-MGB coupling shaft
MET 63.10.00.601 A 2500 FH X 250 FH
19E226-6A (704A33621003)
19E226-7A (704A33621005)
19E226-8A (704A33621004)
332A54-2012-00 (-)
332A54-2012-01 (-)
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/20/00/000/000/010
MGB
MET 60.00.00.302 PO A 25 FH X 3 FH
After the introduction to service of a new, overhauled or repaired component.
Oil change.
DRN
63/20/00/000/000/030
MGB
MET 60.00.00.603 PO A 10 FH X 2 FH
Each time after the component is installed.
Check of the chip detector.
DI
63/20/00/000/000/060
MGB
MET 60.00.00.604 PO A 1 FH X 0A
& 10 FH X 1 FH
& 25 FH X 2 FH
& 50 FH X 5 FH
After the introduction to service of a new, overhauled or repaired component.
Spectrometric oil analysis is an optional monitoring process.
DI
63/20/00/601/000/080
Epicyclic module - Cover
MET 63.20.00.601 PO A 100 FH X 10 FH
§ F.1.b
Each time after the component is installed.
Flared housing - epicyclic module - main casing attachment bolts tightening torque load check.
TCK
63/20/00/601/000/095
MGB
MET 63.21.00.601 PO A 3 FH X 7 FH
& 50 FH X 5 FH
After the introduction to service of a new, overhauled or repaired component.
LEBOZEC ET GAUTIER: check and clean.
ROBINDUS: check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/20/00/000/000/015
MGB
MET 60.00.00.302 A 600 FH X 60 FH
// 4Y X 146 D
Synthetic oil change.
DRN
63/20/00/000/000/025
MGB
MET 60.00.00.302 A 400 FH X 40 FH
// 2Y X 73 D
Mineral oil change.
DRN
63/20/00/000/000/050
MGB
MET 60.00.00.604 A 100 FH X 10 FH
Spectrometric oil analysis is an optional monitoring process.
DI
63/20/00/000/000/090
Switch
MET 60.00.00.601 A 6Y X 180 D
Calibration check.
DI
63/20/00/000/000/100
MGB - Thermostatic switch and temperature probe
MET 60.00.00.602 A 6Y X 180 D
Calibration check.
DI
63/20/00/000/000/130
MGB
MET 05.39.00.601 A 4Y X 146 D
§ F.2
Tropical and damp atmosphere
Salt-laden atmosphere
Detailed check.
Initial compliance at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 4 Y.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/20/00/000/000/150
MGB
MET 05.39.00.601 A 6Y X 180 D
§ F.2
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 6 Y.
DI
63/20/00/000/000/160
Chip detector
MET 60.00.00.603 A 500 FH X 50 FH
§ F.6
Continuity check.
With electric indication.
DI
63/20/00/000/000/190
Rotor brake flange attachment
MET 63.23.01.603 A 50 FH X 5 FH
§ F.7.a
PRE MOD 0752365 // PRE MOD 0752492
Visual check.
GVI
63/20/00/000/000/200
Rotor brake flange attachment
MET 63.23.01.603 A 50 FH X 5 FH
§ F.7.b
PRE MOD 0752507
Before repair following task MRM 63.26.00.708.
Visual check.
GVI
63/20/00/000/000/210
Rotor brake flange attachment
MET 63.23.01.603 A 50 FH X 5 FH
§ F.7.c
POST MOD 0752507
Visual check.
GVI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/20/00/000/000/220
Rotor brake flange attachment
MET 63.23.01.603 A 50 FH X 5 FH
§ F.7.d
PRE MOD 0752507
After repair following task MRM 63.26.00.708.
Visual check.
GVI
63/20/00/601/000/000
MGB
MET 63.20.00.601 A 500 FH X 50 FH
EXC. § F.1.e.1
EXC. § F.1.e.2
Check.
DI
63/20/00/601/000/010
MGB
MET 63.20.00.601 A 2M X 6D
§ F.1.g
Helicopter based aboard a ship.
Check.
DI
63/20/00/601/000/090
MGB
MET 63.20.00.601 A 500 FH X 50 FH
§ F.1.b
Flared housing - epicyclic reduction gear - main casing attachment bolts tightening torque load check.
TCK
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/21/00/601/000/010
MGB - Filter - Emergency system
MET 63.21.00.601 A 50 FH X 5 FH
§ F.3.a
LEBOZEC ET GAUTIER oil filter.
Check to ensure that there is no rotary movement on the plate.
VC
63/21/00/601/000/020
MGB - Filter - Plug
MET 63.21.00.601 A 500 FH X 50 FH
§ F.3.b
LEBOZEC ET GAUTIER oil filter.
Oil filter plug security check.
TCK
63/23/01/501/000/000
Rotor brake
MET 63.23.01.501 A 7500 FH X 300 FH
Testing and control adjustment.
FT
63/23/01/603/000/000
Brake linings
MET 63.23.01.603 A 500 FH X 50 FH
§G
Dimensional check.
DI
63/23/01/603/000/005
Rotor brake
MET 63.23.01.603 A 50 FH X 5 FH
§ F.8
POST MOD 0723738 & PRE MOD 0726696
Visual check of the bush of the control handle.
VC
63/23/01/603/000/010
Rotor brake
MET 63.23.01.603 A 7500 FH X 300 FH
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/25/00/000/000/000
MGB oil cooler
MET 63.25.00.301 A 100 FH X 10 FH
§K
Salt-laden atmosphere
When the aircraft hovers or flies at low altitude, these operations must be performed during
the check after the last flight of the day.
Rinse.
CLN
63/25/00/301/000/010
MGB - Oil cooler
MET 63.25.00.301 A 3000 FH X 300 FH
// 6Y X 180 D
Cleaning.
CLN
63/25/00/502/000/010
Fan assembly
MET 63.25.00.502 A 500 FH X 50 FH
Vibratory level measurement without Steady Control.
GR
63/25/00/601/000/000
Oil cooling system
MET 63.25.00.601 A 500 FH X 50 FH
Check.
GVI
63/25/00/602/000/000
Oil cooling system
MET 63.25.00.602 A 50 FH X 5 FH
§ F.2
Oil cooler ducts and fan mounts.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/25/00/602/000/010
Flexible couplings
MET 63.25.00.602 A 100 FH X 10 FH
§ F.1
GVI
63/25/00/602/000/020
Fan assembly - Rotor
MET 63.25.00.602 A 200 FH X 20 FH
§ F.6
332A39-0105-00 (-)
332A39-0105-01 (-)
332A39-0105-02 (-)
Visual check.
GVI
63/25/00/602/000/030
Fan assembly
MET 63.25.00.602 A 500 FH X 50 FH
§ F.3
When compliance with § F.3.c is ensured, if cracks outside the tolerance limits are found,
reduce the checking interval to 50 FH.
GVI
63/25/00/603/000/000
Fan assembly
MET 63.25.00.603 A 500 FH X 50 FH
Vibratory level measurement with Steady Control.
GR
63/26/00/000/000/078
MGB - Main casing
MET 63.20.00.601 A 2M X 6D
§ F.1.h
Helicopter based aboard a ship.
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 8
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/30/00/601/000/020
MGB support - Flexible mounting plate
MET 63.30.00.601 A 500 FH X 50 FH
§G
EXC. § G.1.a
Check.
Check the flexible mounting plate-to-transmission deck attachment bolts tightening torque load.
DI|TCK
63/30/00/602/000/000
MGB support - Suspension bar and bolt
MET 63.30.00.602 A 7500 FH X 300 FH
EXC. § F.3
Check.
DI
63/30/00/602/000/010
MGB support - Suspension bar
MET 63.30.00.602 A 12 Y X 180 D
§ F.3
X-ray inspection.
SDI
63/30/00/603/000/000
MGB support
MET 63.30.00.603 A 7500 FH X 300 FH
// 15 Y X 180 D
Check of the seating plane.
DI
63/30/00/604/000/000
MGB support - Suspension bar - Attachment plate
MET 63.30.00.604 A 7500 FH X 300 FH
Check.
DI
AS 532 SC
05-20-00
2021.07.28 ATA 63 Page 9
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/10/00/602/000/011
Tail rotor blade
MET 64.10.00.602 PO A 50 FH X 5 FH
& 250 FH X 25 FH
332A12-0020-XX (-)
332A12-0050-XX (-)
After the introduction to service of a new, overhauled or repaired component.
Check.
DI
64/10/00/602/000/016
Tail rotor blade
MET 64.10.00.602 PO A 100 FH X 10 FH
& 200 FH X 20 FH
332A12-0045-XX (-)
332A12-0055-XX (-)
After the introduction to service of a new, overhauled or repaired component.
Check.
DI
64/10/00/000/000/020
Tail rotor blade
MET 60.00.00.304 A 25 FH X 2 FH
Tropical and damp atmosphere
Salt-laden atmosphere
Cleaning.
CLN
64/10/00/602/000/000
Tail rotor blade
MET 64.10.00.602 A 500 FH X 50 FH
Check.
In the event of separation, check every 25 FH during 100 FH.
If no changes are found, return to the normal inspection cycle.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/10/00/602/000/070
Tail rotor blade
MET 64.10.00.602 A 10 FH X 1 FH
Sand-laden and/or dust-laden atmosphere
Visual check for erosion on blades.
In the event of intensive operation in areas with heavily sand-laden atmosphere, all the necessary steps shall be
taken to ensure optimum operation of the aircraft, if required, the proposed intervals shall be shortened.
GVI
64/20/00/000/000/030
TGB
MET 60.00.00.603 PO A 5 FH X 2 FH
Each time after the component is installed.
Check of the chip detector.
DI
64/20/00/000/000/050
TGB
MET 60.00.00.604 PO A 1 FH X 0A
& 10 FH X 1 FH
After the introduction to service of a new, overhauled or repaired component.
Spectrometric oil analysis is an optional monitoring process.
DI
64/20/00/000/000/060
TGB
MET 60.00.00.604 PO A 25 FH X 2 FH
& 50 FH X 5 FH
332A36-0002-XX (-)
After the introduction to service of a new, overhauled or repaired component.
Spectrometric oil analysis is an optional monitoring process.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/20/00/000/000/077
Pitch horn
MET 64.20.00.603 PO A 5 FH X 5 FH
F.3.d.2
Each time after the component is installed.
Check of the tightening torque of the nuts.
TCK
64/20/00/601/000/000
TGB
MET 64.20.00.601 PO A 3 FH X 7 FH
§ H.1 & 100 FH X 10 FH
Each time after the component is installed.
Readjustment of the attachment bolts tightening torque.
RTQ
64/20/00/603/000/128
Sleeve nut
MET 64.20.00.603 PO A 3 FH X 7 FH
F.3.i & 500 FH X 50 FH
After the introduction to service of a new, overhauled or repaired component.
Tightening torque check.
TCK
64/20/00/000/000/010
TGB
MET 60.00.00.302 A 1500 FH X 150 FH
// 4Y X 146 D
Oil change - Synthetic oil.
DRN
64/20/00/000/000/025
TGB
MET 60.00.00.302 A 500 FH X 50 FH
// 2Y X 73 D
Oil change - Mineral oil.
DRN
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/20/00/000/000/037
Tail rotor power transmission system
MET 05.39.00.601 A 4Y X 146 D
§ F.6
Tropical and damp atmosphere
Salt-laden atmosphere
Detailed check.
Initial compliance at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 4 Y.
DI
64/20/00/000/000/039
Tail rotor power transmission system
MET 05.39.00.601 A 6Y X 180 D
§ F.6
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 6 Y.
DI
64/20/00/000/000/040
TGB
MET 60.00.00.604 A 100 FH X 10 FH
Spectrometric oil analysis is an optional monitoring process.
DI
64/20/00/000/000/150
TGB - Temperature probe
MET 60.00.00.602 A 6Y X 180 D
EXC. § F
Calibration check.
DRN|FT
64/20/00/000/000/170
TGB - Chip detector
MET 64.40.00.601 A 500 FH X 50 FH
§ F.2
Continuity check.
With electric indication.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/20/00/301/000/010
Tail rotor power transmission system - TRH control bearing
MET 64.20.00.301 A 300 FH (P) 30 FH
§ G.3 // 1 Y (P) 36 D
SP22516B05RB20 (704A33651235)
POST MOD 0766205
Greasing and check.
LUB|DI
64/20/00/601/000/010
TGB
MET 64.20.00.601 A 500 FH X 50 FH
Check.
DI
64/20/00/603/000/040
Tail rotor hub
MET 64.20.00.603 A 500 FH X 50 FH
§ F.3 // 2Y X 73 D
Detailed check.
DI
64/20/00/603/000/050
Sliding sleeve
MET 64.20.00.603 A 1000 FH X 100 FH
§ F.4.a // 4Y X 146 D
Check.
DI
64/20/00/603/000/060
Flapping hinge
MET 64.20.00.603 A 1000 FH X 100 FH
F.5.a.1
Detailed check.
DI
64/20/00/603/000/065
Sleeve spindle assembly - Spindle
MET 64.20.00.603 A 1000 FH X 100 FH
§ F.5.a.2.a
Wear check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
64/20/00/603/000/110
Pitch rod
MET 64.20.00.603 A 100 FH X 10 FH
§ F.2.a
Check.
DI
64/20/00/603/000/115
Control rod - Protective boot
MET 64.20.00.603 A 100 FH X 10 FH
§ E.4 // 3M X 9D
PRE MOD 0766200
Greasing.
LUB
AS 532 SC
05-20-00
2020.07.31 ATA 64 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/10/00/000/000/340
Tail rotor drive
MET 05.39.00.601 A 4Y X 146 D
§ F.4
Tropical and damp atmosphere
Salt-laden atmosphere
Detailed check.
Initial compliance at the 8 Y limit (margin 180 D) from the first date of installation (startup),
or on-condition maintenance then every 4 Y.
DI
65/10/00/000/000/360
Tail rotor drive
MET 05.39.00.601 A 6Y X 180 D
§ F.4
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation (startup),
or on-condition maintenance then every 6 Y.
DI
65/10/00/520/603/100
Drive shaft bearing blocks – Regreasable bearing
MET 65.10.00.603 A 50 FH X 5 FH
§ F.1.a
Fitted on assemblies PRE MOD 0728432: MP/N 332A340040.02, MP/N 332A340042.00/.01,
MP/N 332A340027.02/.03/.04/.05/.06/.07, MP/N 332A340050.00/.01/.02/.03, MP/N
332A340051.00 and MP/N 332A340055.00.
Check for grease leakage.
VC
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/10/00/520/603/150
Drive shaft bearing blocks – Regreasable bearing
MET 65.10.00.603 A 150 FH X 15 FH
§ F.1.a
Fitted on assemblies POST MOD 0728432: MP/N 332A340040.04, MP/N 332A340042.02/.03,
MP/N 332A340027.09/.10/.11/.12/.13/.14, MP/N 332A340050.04/.05/.06/.07, MP/N
332A340051.01 and MP/N 332A340055.02.
Check for grease leakage.
VC
65/10/00/520/603/300
Single-bearings block and dual bearing block - Regreasable bearing
MET 65.10.00.603 A 500 FH X 50 FH
§ F.3
ALL MP/N (-)
Check for bearing free rotation of bearings without diconnection of the shaft.
VC
65/10/00/520/603/400
Coupling shaft
MET 65.10.00.603 A 500 FH X 50 FH
§ I.1 // 6Y X 180 D
Normal climatic conditions
Visual inspection without removal.
Initial compliance in calendar at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 6 Y.
VC
65/10/00/520/603/450
Coupling shaft
MET 65.10.00.603 A 500 FH X 50 FH
§ I.1 // 4Y X 146 D
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
Visual inspection without removal.
Initial compliance in calendar at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 4 Y.
VC
65/10/00/520/603/500
Flexible couplings
MET 65.10.00.603 A 500 FH X 50 FH
§ G.2
Tightening torque load check.
TCK
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/10/00/520/603/550
MGB tail rotor drive flange - Flexible coupling
MET 65.10.00.603 A 500 FH X 50 FH
§ G.3.a // 6Y X 180 D
Normal climatic conditions
Visual inspection with removal.
Initial compliance in calendar at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 6 Y.
GVI
65/10/00/520/603/570
MGB tail rotor drive flange - Flexible coupling
MET 65.10.00.603 A 500 FH X 50 FH
§ G.3.a // 4Y X 146 D
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
Visual inspection with removal.
Initial compliance in calendar at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 4 Y.
GVI
65/10/00/520/603/600
Bearing block
MET 65.10.00.603 A 500 FH X 50 FH
§ H.1.b
§ H.2
Visual inspection without removal.
VC
65/10/00/520/603/650
Single-bearings block and dual bearing block - Non-regreasable bearing
MET 65.10.00.603 A 500 FH X 50 FH
§ F.4.a
§ F.5.a
Check for bearing free rotation with removal.
Check for play.
DI
65/10/00/520/603/700
Single-bearings block and dual bearing block - Regreasable bearing
MET 65.10.00.603 A 1500 FH X 150 FH
§ F.5.b
ALL MP/N (-)
Check for play.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/10/00/520/603/750
Coupling shaft
MET 65.10.00.603 A 1500 FH X 150 FH
§ I.2
Visual inspection with removal.
SDI
65/10/00/601/000/010
Tail rotor drive shaft
MET 65.10.00.601 A 6Y X 180 D
§G
Removal and check of the drive shaft.
DI
65/10/00/602/000/000
Tail rotor drive shaft
MET 65.10.00.602 A 7500 FH X 300 FH
Alignment check.
DI
65/10/00/603/000/010
Tail rotor drive shaft - Regreasable bearing
MET 65.10.00.603 A 6M X 18 D
§ F.2
ALL MP/N (-)
Salt-laden atmosphere
Check and lubrication.
DI|LUB
65/10/00/603/000/050
Flexible couplings
MET 65.10.00.603 A 1500 FH X 150 FH
§ G.3.b // 6Y X 180 D
Normal climatic conditions
Visual inspection with removal.
Initial compliance in calendar at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 6 Y.
GVI
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/10/00/603/000/053
Flexible couplings
MET 65.10.00.603 A 1500 FH X 150 FH
§ G.3.b // 4Y X 146 D
Tropical and damp atmosphere
Salt-laden atmosphere
Sand-laden and/or dust-laden atmosphere
Visual inspection with removal.
Initial compliance in calendar at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or on-condition maintenance then every 4 Y.
GVI
65/20/00/000/000/020
IGB
MET 60.00.00.603 PO A 5 FH X 2 FH
Each time after the component is installed.
Check of the chip detector.
DI
65/20/00/000/000/040
IGB
MET 60.00.00.604 PO A 1 FH X 0A
& 10 FH X 1 FH
& 25 FH X 2 FH
& 50 FH X 5 FH
After the introduction to service of a new, overhauled or repaired component.
Spectrometric oil analysis is an optional monitoring process.
DI
65/20/00/601/000/000
IGB
MET 65.20.00.601 PO A 3 FH X 7 FH
§ F.6 & 100 FH X 10 FH
Each time after the component is installed.
Check of the attachment bolt tightening torque.
TCK
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/20/00/000/000/003
IGB
MET 60.00.00.302 A 1500 FH X 150 FH
// 4Y X 146 D
Synthetic oil change.
DRN
65/20/00/000/000/013
IGB
MET 60.00.00.302 A 500 FH X 50 FH
// 2Y X 73 D
Mineral oil change.
DRN
65/20/00/000/000/030
IGB
MET 60.00.00.604 A 100 FH X 10 FH
Spectrometric oil analysis is an optional monitoring process.
DI
65/20/00/000/000/100
IGB - Thermostatic switch
MET 60.00.00.602 A 6Y X 180 D
EXC. § F
Calibration check.
FT
65/20/00/000/000/110
Chip detector
MET 65.40.00.601 A 500 FH X 50 FH
§ F.2
Continuity check.
With electric indication.
DI
65/20/00/601/000/010
IGB
MET 65.20.00.601 A 500 FH X 50 FH
§F
Check.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
65/20/00/601/000/020
IGB
MET 05.39.00.601 A 4Y X 146 D
§ F.5
Tropical and damp atmosphere
Salt-laden atmosphere
Detailed check.
Initial compliance at the 8 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 4 Y.
DI
65/20/00/601/000/040
IGB
MET 05.39.00.601 A 6Y X 180 D
§ F.5
Normal climatic conditions
Detailed check.
Initial compliance at the 12 Y limit (margin 180 D) from the first date of installation
(startup), or last Overhaul then every 6 Y.
DI
AS 532 SC
05-20-00
2020.07.31 ATA 65 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
66/20/00/601/000/010
Folding pylon
MET 66.20.00.601 A 1500 FH X 150 FH
§ F.2 // 6Y X 180 D
System check.
DI
66/20/00/602/000/000
Folding pylon
MET 66.20.00.602 A 2Y X 73 D
System check.
DI
AS 532 SC
05-20-00
2015.10.15 ATA 66 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/00/00/501/000/020
Rotor control
MET 67.00.01.501 A 7500 FH X 300 FH
POST MOD 0726640
Testing and rigging all the rotor controls.
DI
67/00/00/601/000/000
Control channels
MET 67.00.00.601 A 1000 FH X 100 FH
EXC. § F.6 // 2Y X 73 D
PRE MOD 0726640
Check without disassembly.
DI
67/00/00/601/000/010
Control channels
MET 67.00.01.601 A 1000 FH X 100 FH
EXC. § F.6 // 2Y X 73 D
EXC. § F.7
POST MOD 0726640
Check without disassembly.
DI
67/00/00/601/000/020
Control channel - Yaw damper support
MET 67.00.01.601 A 1500 FH X 150 FH
§ F.6
332A25-1334-00 (-)
POST MOD 0726640
Check without disassembly.
This crack detection inspection is applicable only for helicopters that have logged more than 16000 FH.
GVI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/00/00/601/000/030
Control channel
MET 67.00.00.601 A 1000 FH X 100 FH
§ F.6 // 1Y X 36 D
PRE MOD 0726640
Salt-laden atmosphere
Condition check of the tail rotor control cables.
DI
67/00/00/601/000/040
Control channel
MET 67.00.00.601 A 1000 FH X 100 FH
§ F.6 // 2Y X 73 D
PRE MOD 0726640
Condition check of the tail rotor control cables.
DI
67/00/00/601/000/050
Control channel
MET 67.00.01.601 A 1000 FH X 100 FH
§ F.7 // 1Y X 36 D
POST MOD 0726640
Salt-laden atmosphere
Condition check of the tail rotor control cables.
DI
67/00/00/601/000/060
Control channel
MET 67.00.01.601 A 1000 FH X 100 FH
§ F.7 // 2Y X 73 D
POST MOD 0726640
Condition check of the tail rotor control cables.
DI
67/00/00/602/000/000
Rotor control
MET 67.00.00.602 A 7500 FH X 300 FH
PRE MOD 0726640
Check of the main rotor feathering angle variations.
DI
67/00/00/602/000/010
Rotor control
MET 67.00.01.602 A 7500 FH X 300 FH
POST MOD 0726640
Check of the main rotor feathering angle variations.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/00/00/604/000/000
Tail rotor
MET 67.00.00.604 A 7500 FH X 300 FH
PRE MOD 0726640
Incidence Angle Variation check.
DI
67/00/00/604/000/010
Tail rotor
MET 67.00.01.604 A 7500 FH X 300 FH
POST MOD 0726640
Incidence Angle Variation check.
DI
67/00/00/605/000/000
Rotor control
MET 67.00.00.605 A 7500 FH X 300 FH
PRE MOD 0726640
Check of the clearances at the control stops.
DI
67/00/00/605/000/010
Rotor control
MET 67.00.01.605 A 7500 FH X 300 FH
POST MOD 0726640
Check of the clearances at the control stops.
DI
67/10/00/301/000/010
Pitch Indicators
MET 67.10.01.601 A 6Y X 180 D
POST MOD 0726640
Calibration Check.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 3
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/10/00/501/000/000
Cyclic pitch
MET 67.10.00.501 A 7500 FH X 300 FH
PRE MOD 0726640
Adjustment of the stick balancing.
DI
67/10/00/501/000/010
Cyclic pitch
MET 67.10.01.501 A 7500 FH X 300 FH
POST MOD 0726640
Adjustment of the stick balancing.
DI
67/10/00/502/000/000
Collective pitch
MET 67.10.00.502 A 7500 FH X 300 FH
PRE MOD 0726640
Adjustment of the balancing of the collective pitch levers.
DI
67/10/00/502/000/010
Collective pitch
MET 67.10.01.502 A 7500 FH X 300 FH
POST MOD 0726640
Adjustment of the balancing of the collective pitch levers.
DI
67/10/00/503/000/000
Collective pitch - Elastic stop
MET 67.10.00.503 A 15 Y X 180 D
PRE MOD 0726640
Check and adjustment.
DI
67/10/00/503/000/010
Collective pitch - Elastic stop
MET 67.10.01.503 A 15 Y X 180 D
POST MOD 0726640
Check and adjustment.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 4
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/10/00/505/000/000
Collective pitch - Hydraulic damper
MET 67.10.00.505 A 6Y X 180 D
PRE MOD 0722931 & PRE MOD 0726640
Adjustment-Check-Filling.
DRN|DI
67/10/00/505/000/010
Collective pitch - Hydraulic damper
MET 67.10.01.505 A 6Y X 180 D
POST MOD 0726640
Adjustment of longitudinal or lateral damper.
DRN|DI
67/10/00/506/000/000
Collective pitch - Hydraulic damper
MET 67.10.00.506 A 6Y X 180 D
POST MOD 0722931
Filling - Checking.
DRN|DI
67/10/00/602/000/000
L'HOTELLIER ball end-fittings
MET 05.23.00.602 A 500 FH X 50 FH
§ F.2.a
Check.
DI
67/20/00/501/000/010
Return rod
MET 67.20.01.501 A 1500 FH X 150 FH
// 2Y X 73 D
POST MOD 0726640
Adjustment.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 5
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/20/00/601/000/000
Yaw control - Forward control quadrant
MET 67.20.00.601 A 7500 FH X 300 FH
// 15 Y X 180 D
PRE MOD 0726640
Check with removal-installation.
DI
67/20/00/601/000/010
Yaw control - Forward control quadrant
MET 67.20.01.601 A 7500 FH X 300 FH
// 15 Y X 180 D
POST MOD 0726640
Check with removal-installation.
DI
67-30 SERVOCONTROLS
67/30/00/404/000/060
Main servocontrol - Attachment bolt
MET 67.30.00.401 PO A 15 FH X 5 FH
Each time after the component is installed.
Readjustment of the tightening torque after removal-installation.
RTQ
67/30/00/601/000/000
Servocontrol
MET 67.30.00.601 A 2Y X 73 D
PRE MOD 0726640
System check.
DI
67/30/00/601/000/005
Servocontrol
MET 67.30.01.601 A 2Y X 73 D
POST MOD 0726640
System check.
DI
67/30/00/601/000/010
Tail servocontrol - Input rod
MET 67.30.00.601 A 500 FH X 50 FH
§ G.2
PRE MOD 0726640
Check.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 6
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/30/00/601/000/020
Tail servocontrol - Input rod
MET 67.30.01.601 A 500 FH X 50 FH
§ G.2
POST MOD 0726640
Check.
DI
67/30/00/601/000/050
Main servocontrol - Attachment bolts
MET 67.30.00.601 A 500 FH X 50 FH
§ F.5
PRE MOD 0726640
Check.
DI
67/30/00/601/000/060
Main servocontrol - Attachment bolts
MET 67.30.01.601 A 500 FH X 50 FH
§ F.5
POST MOD 0726640
Check.
DI
67/30/00/605/000/000
Servocontrol
MET 67.30.00.605 A 1500 FH X 150 FH
PRE MOD 0726640
Play measurement at anchoring swivel bearings and hinges.
DI
67/30/00/605/000/010
Servocontrol
MET 67.30.01.605 A 1500 FH X 150 FH
POST MOD 0726640
Play measurement at anchoring swivel bearings and hinges.
DI
67/30/00/606/000/000
Tail servocontrol - Distributor levers
MET 67.30.00.606 A 500 FH X 50 FH
PRE MOD 0726640
Check for play.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 7
MSM
Task Number
Documentation Interval Margin
Description/Remarks
67/30/00/606/000/005
Tail servocontrol - Distributor levers
MET 67.30.01.606 A 500 FH X 50 FH
POST MOD 0726640
Check for play.
DI
67/91/00/000/000/010
Strong wind starting system
MET 67.90.01.201 A 4Y X 146 D
POST MOD 0726640
Preparation of the system.
DI
AS 532 SC
05-20-00
2017.07.10 ATA 67 Page 8
MSM
Task Number
Documentation Interval Margin
Description/Remarks
71-00 POWERPLANT
71/00/00/601/000/000
Power plant installation
MET 71.00.00.601 A 2Y X 73 D
Check.
DI
71/00/00/602/000/000
Power plant installation
MET 71.00.00.602 A 7500 FH X 300 FH
Alignment checks.
DI
71/52/00/601/000/020
Exhaust gas deflector
MET 71.52.00.601 PO A 8 FH X 7 FH
Each time after the component is installed.
Detailed check.
DI
71/52/00/601/000/000
Exhaust gas deflector
MET 71.52.00.601 A 150 FH X 15 FH
§ F.6
Detailed check.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 71 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
71/52/00/601/000/010
Exhaust gas deflector
MET 71.52.00.601 A 75 FH X 7 FH
§ F.4
§ F.1
§ F.2
§ F.5
Visual check.
GVI
71/52/00/601/000/012
Replacement nozzle - Exhaust gas deflector
MET 71.52.01.601 A 500 FH X 50 FH
§ F.1
Detailed check.
DI
71/52/00/601/000/015
Replacement nozzle - Exhaust gas deflector
MET 71.52.01.601 A 75 FH X 7 FH
§ F.2
Visual check.
GVI
71/52/00/602/000/010
Exhaust gas deflector – Secondary nozzle
MET 71.52.00.602 A 50 FH X 5 FH
§ F.1.b
POST MOD 0726757
Detailed check.
DI
AS 532 SC
05-20-00
2018.02.05 ATA 71 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 72-ENGINE
72-10 ENGINES
72/10/00/000/000/000
Engine compressor
AS 532 SC
05-20-00
2013.01.10 ATA 72 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
76/10/00/602/000/000
L'HOTELLIER ball end-fittings
MET 05.23.00.602 A 500 FH X 50 FH
§ F.2.b
Check.
DI
76/20/00/520/403/100
General cut-out handle
MET 76.20.00.403 A 15 Y X 180 D
Removal and replacement.
RS
76/20/00/601/000/000
Fuel shut-off control
MET 76.20.00.601 A 500 FH X 50 FH
EXC. § J // 2Y X 73 D
Checks and greasing.
DI|LUB
AS 532 SC
05-20-00
2018.02.05 ATA 76 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
76/20/00/602/000/000
Fuel shut-off control
MET 76.20.00.602 A 4Y X 146 D
Check and greasing tangentiel unit.
DI|LUB
AS 532 SC
05-20-00
2018.02.05 ATA 76 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
77/20/00/601/000/010
Temperature and pressure
MET 77.21.00.601 A 7500 FH X 300 FH
POST MOD 0726647
T4 line check.
DI
AS 532 SC
05-20-00
2014.01.09 ATA 77 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
80-00 STARTING
80/00/00/601/000/000
Engine starting system
MET 80.00.00.601 A 6Y X 180 D
System check.
GVI
80/10/01/601/000/000
Starting system
MET 80.10.01.601 A 500 FH X 50 FH
Very cold weather
System checks with the system switched off.
GVI
AS 532 SC
05-20-00
2017.07.10 ATA 80 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 28-FUEL
28/93/00/601/000/010
Preclogging alarm
MET 28.93.00.601
AS 532 SC
05-50-00
2013.01.10 ATA 28 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
30/20/00/000/000/090
Heating mats
MET 30.20.00.601
592180 (704A34672001)
Monitoring of bond separations between heating mats and air intake cowling.
If bond separations meet the criteria given in § F.4.a.3, suspend flights in icing
conditions and repair within the next 10 hours.
30/20/00/000/000/100
Heating mats
MET 30.20.00.601
592180 (704A34672001)
Monitoring of bond separations between heating mats and air intake cowling.
If bond separations meet the criteria given in § F.4.a.2 repair within the next 50 hours.
AS 532 SC
05-50-00
2017.02.06 ATA 30 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
Clearance checks After the tail bumper has touched the ground or in the event of difficulties when rigging the tail rotor.
AS 532 SC
05-50-00
2013.01.10 ATA 32 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 33-LIGHTS
PRE SB.33.00.03.
Fitted with transformer-rectifier MP/N TR992-7.
Inspection to be done After a component failure (10 hours or 5 flights).
If the inspections specified on work card33.20.00.601 cannot be done, isolate the neon tubes.
AS 532 SC
05-50-00
2013.01.10 ATA 33 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
Crack detection.
After the appearance of one of the following:
- oil leak in the feathering hinge,
- oil consumption but no leakage,
- progressive abnormal modifications in the rotor dynamic balancing.
AS 532 SC
05-50-00
2013.01.10 ATA 62 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/28/00/550/701/080
23000 rpm input
MRM 63.28.00.701 A 6 FH X 0A
Replacement of the seal.
Type B2 measures as per MET 05.53.00.607 § F.3.b.
To be performed within 6 FH.
63/28/00/550/701/090
23000 rpm input
MRM 63.28.00.701 A 10 FH X 0A
Replacement of the seal.
Type B1 measures as per MET 05.53.00.607 § F.3.b.
To be performed within 10 FH.
AS 532 SC
05-50-00
2018.08.17 ATA 63 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
AS 532 SC
05-50-00
2013.01.10 ATA 64 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
ATA 53-FUSELAGE
53/10/41/701/000/020
Tail boom frame - Scratch
MRM 53.10.41.701 PO A 100 FH X 10 FH
§ F.3
Visual check.
VC
53/10/00/605/000/020
Canopy structure
MET 53.10.00.605 A 10 FH X 1 FH
§ F.2
If there is a crack corresponding to the criteria given in § F.2: check for non-propagation of crack.
GVI
53/10/41/701/000/030
Tail boom frame - Crack
MRM 53.10.41.701 A ALF A X 0A
§ F.1
Visual check during the first 50 FH until permanent repair.
VC
53/10/41/701/000/040
Tail boom frame - Crack
MRM 53.10.41.701 A 50 FH X 5 FH
§ F.1
Visual check until permanent repair.
VC
53/10/41/701/000/050
Tail boom frame - Damage to inboard edge of frame
MRM 53.10.41.701 A 300 FH X 30 FH
§ F.4
Visual check.
VC
AS 532 SC
05-52-00
2018.02.05 ATA 53 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
53/10/41/701/000/060
Tail boom frame - Corrosion
MRM 53.10.41.701 A 6M X 18 D
§ F.5
Visual check.
VC
53/10/41/701/000/070
Tail boom frame - Corrosion
MRM 53.10.41.701 A 2M X 6D
§ F.5
Salt-laden atmosphere
Tropical and damp atmosphere
Visual check.
VC
53/10/41/701/000/080
Tail boom frame - Impact mark and dent
MRM 53.10.41.701 A 100 FH X 10 FH
§ F.6
Visual check.
VC
AS 532 SC
05-52-00
2018.02.05 ATA 53 Page 2
MSM
Task Number
Documentation Interval Margin
Description/Remarks
63/20/01/052/000/010
Rotor brake flange attachment
MET 63.23.01.603 A 25 FH X 2 FH
§ F.7.d
PRE MOD 0752507
After repair following task MRM 63.26.00.708.
Visual check during the first 100 FH.
GVI
AS 532 SC
05-52-00
2021.07.28 ATA 63 Page 1
MSM
Task Number
Documentation Interval Margin
Description/Remarks
AS 532 SC
05-52-00
2017.02.06 ATA 71 Page 1