Professional Documents
Culture Documents
SDI1606
V2.2
Tel: 86-0755-82981311
Fax-Number: 86-0755-82844170
Website: www.solidic.net
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
1:Pin Configuration
Digital Interface
CLK Clock Input Port On The Rising Edge Of The Input/Output data
Display Driver
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
The Output of Grid
Common anode: P—Open-Drain for Outputs
Common cathode: N—Open-Drain for Outputs
GRID0 ~ GRID6 Output(Grid) Keyboard Scanning:High Resistance or Floating
VSW The Input of voltage Low voltage input from this pin
RVDD The Output of voltage High voltage output from the port
2:Description Of Parameter
The integrated circuit has a ESD (Electro-Static Discharge) protection circuit,
electrostatic discharge may cause the entire chip does not work ,may also have some
adverse effects on the chip circuit, resulting in less than the expected results to our information.
Therefore, the use of time should be as far as possible to avoid direct contact with the hands of the
Limiting Conditions:
As shown in Table 2.
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
Electrical Parameters:
Table 3. Parameters.
Test Condition:
The voltage is about 5.0 V (DVDD)
The temperature ranges from -25~80℃
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
3:Functional Module
3.1 Display Memory
As shown in the following table 4, SDI1606 uses 7-bytes of RAM corresponding to the 7
digital tube, the corresponding bit is "1", which means that the corresponding digital tube segment
needs to be lit.
Table 4. Address Memory of Display.
SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1 SEG0
Bit7 Bit6 Bit5 Bit4 Bit1 Bit2 Bit1 Bit0
Memory Address 00H GRID0
Memory Address 01H GRID1
Memory Address 02H GRID2
Memory Address 03H GRID3
Memory Address 04H GRID4
Memory Address 05H GRID5
Memory Address 06H GRID6
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
Tips: The circuit between the filter capacitor and the positive and negative poles of the chip
should be as short as possible.
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
Attention:KEYCODE1 Only Recongnized one key,KEY0 has the highest priority and KEY7
has the lowest priority。
for example:
KEY0、KEY7Press at the same time,CD2\CD1\CD0 is“111”
KEYCODE2:
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
KEY7 KEY6 KEY5 KEY4 KEY3 KEY2 KEY1 KEY0
KEYCODE2 is used for condition that more than one key are pressed,to avoid
interfere LED displae,Doide must be added
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
4:Specification of Interface
Figure 7
Command1: Data Settings
Command2: Address Settings
Data1~N: The Contents of The Display Data
Command3: Control Bit
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
Read the key process: As is shown in fig. 9a, In setting the read scanning command, the
Key data is ready,and then you can read the key data. As shown in fig. 9b, the SDI1606
after receiving the instruction of reading key scan mode, at the first falling edge clock
SCLK, the data port DIO will be set to high level, and then read the data from the DIO,
after reading the level is set to low level on the DIO, an effective data read operation is
completed.
5:Data Instruction
The data command is used to set the display mode and the status of the LED drive.
After the start bit of the instruction data is valid, the first byte of the data entered by DIN is
used as an instruction. The highest two bit bits of the decoded instruction data are used as
criteria for distinguishing different instructions.
B7 B6 Instructions
0 1 Data command setting
1 0 Commands used to control display
1 1 Command to control address
B7 B6 B5 B4 B3 B2 B1 B0 Explanation
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
0 1 0 0 0 Writes data to the display register
0 1 1 0 Data scanning
0 1 0 Internal Address increased by 1
0 1 1 Fixed address
0 1 0
0 1 1 Test mode
B7 B6 B5 B4 B3 B2 B1 B0 Address
1 1 0 0 0 0 0 00H
1 1 0 0 0 1 01H
1 1 0 0 1 0 02H
1 1 0 0 1 1 03H
1 1 0 1 0 0 04H
1 1 0 1 0 1 05H
1 1 0 1 1 0 06H
B7 B6 B5 B4 B3 B2 B1 B0
1 0 0 1 0 0 0 Settings of Duty Cycle 1/16
1 0 1 0 0 1 Display Duty Cycle 2/16
1 0 1 0 1 0 Brightness Duty Cycle 4/16
1 0 1 0 1 1 Duty Cycle 10/16
1 0 1 1 0 0 Duty Cycle 11/16
1 0 1 1 0 1 Duty Cycle 12/16
1 0 1 1 1 0 Duty Cycle 13/16
1 0 1 1 1 1 Duty Cycle 14/16
1 0 0 X X X Settings of OFF
1 0 1 X X X Display ON
switch
1 0 10 0 X X X Set Display ON
1 0 1 X X X to The OFF
1 0 X 0 X X Boost Mode External Resistance
Voltage Divider
1 0 X 1 X X Internal Resistance Voltage
Divider
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
6:PACKAGE DIMENSIONS
6.1 DIP-20
6.2 SSOP-20
_______________________________________________________________________________
www.solidic.net
芯易德科技(深圳)有限公司
SOLIDIC 数据手册 SDI1606 系列
6.2 SSOP-24
_______________________________________________________________________________
www.solidic.net