Professional Documents
Culture Documents
MasterBrace ADH 2200
MasterBrace ADH 2200
®
MasterBrace ADH 2200
(formerly known as Concresive 2200)
High strength, non-flow,
epoxy bedding and repair mortar
Contents
This Technical Summary Consists copies of …..
1. Technical Data Sheet
MasterBrace® ADH 2200
2. Method Statement
3. Material Safety Data Sheets
Tech. Data Sheet
MasterBrace® ADH 2200 (Formerly known as Concresive 2200)
High strength, non-flow, epoxy bedding and repair mortar
DESCRIPTION ADVANTAGES
MasterBrace ADH 2200 is a non slumping epoxy High strength.
bedding compound and adhesive. It is a two pack, Non-slump.
fine aggregate filled, fast curing material, ideal for Strong adhesion.
a variety of bedding, gap filling and concrete repair Impact resistant
applications. Chemical resistant.
MasterBrace ADH 2200 is a stiff but easily Non shrink.
workable compound that can be applied by either Epoxy based.
trowel, spatula or knife. It cures to give high
Trowels to a smooth finish.
mechanical properties typical of epoxy
compounds. It is resistant to oils, greases, Easy to use.
petroleum, salts, many acids and alkalis and most Supplied in pre-weighed units.
commonly met corrosive media. It does not shrink No bonding agent or primer required.
on curing, and is designed to be used when cured
from below freezing point to 60°C. Its impact PACKAGING
resistance, and mechanical strength is greater MasterBrace ADH 2200 is available in 3kg units.
than that of concrete.
COMPOSITION
PRIMARY USES Two-component epoxy-based mortar filled with
For surface repairs of fine cracks and spalls. For selected fine aggregate.
gap filling, grouting, bedding fixtures etc. For
repairs to arrisses without the use of form work. TYPICAL PROPERTIES
Wherever a thixotropic epoxy mortar is required.
Colour: Cement grey
TYPICAL APPLICATIONS Mixed density at 25°C: 1.7g/cm³ (approx.)
Bedding bridge beams or steel bridge bearings. Flashpoint: N/A
Repairing surface defects or to honeycombing Compressive strength 60 N/mm² at 7 days
concrete in horizontal, vertical or overhead to ASTM C579
situations. Bond to concrete: In excess of the
Fixing slip bricks to concrete. cohesive strength of
Securing bolts into walls. concrete
Dowel bars anchoring. Pot life at 25°C 70 minutes
As a gap filling adhesive. at 40°C 30-40 minutes
Filling bolt pockets. Tack free time at 7 hours
Bedding tiles. 25°C
Repairing concrete posts in-situ. at 40°C 2 hours 15 minutes
Cure (by compressive ≥ 60N/mm² at 7 days
Fixing of surface ports for crack injection.
strength) at 25°C:
CHEMICAL RESISTANCE
MasterBrace ADH 2200 has excellent resistance
to the following: most aqueous systems, sewage,
urine, fresh water, sea water, diluted and
concentrated alkalis, diluted acids, sulphur gases,
mineral, vegetable and animal oils and fats,
ammonia and formaldehyde.
MasterBrace® ADH 2200 (Formerly known as Concresive 2200)
BASF_CC-UAE/Br_2200_12_94/v1/11_13
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by
NOTE BASF either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since
they, and not BASF, are responsible for carrying out procedures appropriate to a specific application.
Method Statement
A SMOOTH EPOXY PASTE SUITABLE FOR SEALING SURFACE CRACKS BLOW HOLES AND
OTHER SURFACE DEFECTS IN CONCRETE
1. PREPARATION:
1.1 CRACKS
1.1.1 Chase out the crack using a chisel to form a 'V' at the surface or use an
angle grinder to open up the crack.
1.1.2 Wire brush; blow dust and debris from the crack.
2. MIXING:
2.1. Mix components A and B together until a uniform streak free colour is obtained. In
cold weather if the mixed material is too stiff to apply, mix the material using rubber
gloved hands that have been dipped in water. The inclusion of the moisture will
make the material smoother.
3. APPLICATION:
3.1. Using a spatula, apply the MasterBrace ADH 2200 into the chased out crack, forcing
the material into the concrete surface.
3.2. Smooth off the surface with the spatula.
3.3. To fill blow holes etc. in concrete prior to overcoating, tight trowel the CONCRESIVE
2200 into the prepared surface.
4. TEMPERATURE CONDITIONS:
4.1. This repair system shall be used when the surface and ambient temperature is
above 10°C and will remain so during the curing period.
4.2. In hot weather, areas to be repaired shall be shaded from direct sunlight.
5. CURING:
5.1. No curing is required.
*****
Material Safety Data Sheets
Material Safety Data Sheet
Website: www.saudi-basf.com
3. POTENTIAL HAZARDS
Extinguishing media
Suitable Foam, carbon dioxide, powder extinguisher.
Not to be used Water jet
Combustion products
Further information
After spillage / leakage Absorb with suitable material e.g. sand & earth,
seal in
plastic disposable bag & bury in landfill. Flush
contaminated area with plenty of water.
In addition, please refer to the local
regulations regarding disposal
Page 1 of 3
MasterBrace ADH 2200 BASE
Technical protective measures Store in shaded areas away from direct sunlight.
Keep away from other flammable liquids.
Protection against fire and explosion Avoid use in confined space & sources of
ignition. - No smoking.
Form Paste
Colour white
Odour Resinous
Change in physical state
Boiling point, C(mm Hg) N/A
Melting point, °C
Flash Point(C) N/A
Autoignition temperature (C) N/A
Explosion limits N/A
lower
upper
Thermal decomposition N/A
Density, g/cm3 (°C) Approx.1.815 @ 25°C
Viscosity(C) N/A
pH value(C) N/A
Solubility in water(C) N/A
Further information
11 INFORMATION ON TOXICITY
Page 2 of 3
MasterBrace ADH 2200 BASE
12 INFORMATION ON ECOLOGICAL EFFECTS
Ecological effect information Do not discharge product into drains & sewers.
Impairment of sludge activity
Other information
13. DISPOSAL
Disposal Absorb with sand or earth. Collect in plastic
disposable bags. Bury in landfill.
OR
Mix separate product components in ratio as
supplied and not exceeding single pack size
quantities, in suitable metal containers. Bury
in landfill.
In addition, please refer to the local
regulations regarding disposal
14. TRANSPORT
RID/ADR
UN No. 3082
IMDG Code
GGVE/GGVS
ICAO/IATA Class 9 Pkg Group III
ADNR
Other information Environmentally hazardous substance, liquids
n.o.s
15 REGULATIONS
Approved : MM
Released : AJ
MSDS VERSION: 04
Date: 07/09/06 Last Revision: 25/01/06
Page 3 of 3
Material Safety Data Sheet
MasterBrace ADH 2200 Reactor
Website: www.saudi-basf.com
3. POTENTIAL HAZARDS
Extinguishing media
Suitable Foam, carbon dioxide and dry powder.
Not to be used Water in a jet.
Combustion products
Further information Keep adjacent containers cool by spraying with
water. Wear full protective clothing & self
contained breathing apparatus while fire
fighting
Page 1 of 4
MasterBrace ADH Reactor
Technical protective measures Store in shaded areas away from direct sunlight.
Keep away from other flammable liquids.
Protection against fire and explosion Avoid use in confined space. Ensure good
ventilation
Form Paste
Colour Grey
Odour Amine
Change in physical state
Boiling point, C(mm Hg) N/A
Melting point, °C
Flash Point(C) N/A
Autoignition temperature (C) N/A
Explosion limits N/A
-lower
-upper
Thermal decomposition N/A
Density g/cm3 @ (°C ) Approx.1.642 ( 25 )
Vapour pressure, mbar(C) N/A
Viscosity(C) N/A
pH value(C) N/A
Solubility in water(C) Insoluble
Further information N/A
Page 2 of 4
MasterBrace ADH Reactor
13. DISPOSAL
Disposal Absorb with sand or earth. Collect in plastic
disposable bags. Bury in landfill.
OR
Mix separate product components in ratio as
supplied and not exceeding single pack size
quantities, in suitable metal containers. Bury
in landfill.
In addition, please refer to the local
regulations regarding disposal.
14. TRANSPORT
RID/ADR
UN No. 2735
IMDG Code
GGVE/GGVS
ICAO/IATA Class 8 Packing Group III
ADNR
Other information
Symbol C Corrosive
Page 3 of 4
Concresive 2200 Reactor
The above data are based on our present knowledge. However, they shall not constitute
a guarantee for any specific product features and shall not establish a legally valid
contractual relationship.
Approved : MM
Released : AJ
MSDS VERSION: 04
Page 4 of 4
BASF Construction Chemicals UAE LLC, PO Box 37127, Dubai, UAE, Tel: 00971-4-8090800, Fax: 00971-4-
8851002
e-mail : enquirycc.mideast@basf.com, website : www.basf-cc.ae
Aramco Approval
Test Reports