Professional Documents
Culture Documents
OWNER’S MANUAL
VIDEO, MOVEMENT
& SOUND MONITOR
Model AC1100-A
EN FR ES
2 29 57
TABLE OF CONTENTS
WARNINGS................................................................................... 3
AC1100-A SETUP REQUIREMENTS............................................... 8
STEP 1 - Charging the Parent Unit (10 hours)........................... 9
STEP 2 - Installing the Sensor Pad............................................. 10
STEP 3 - Setting up the Nursery Unit.........................................13
STEP 4 - Turning on your monitor...............................................14
STEP 5 - Testing and getting to know your monitor.............15
STEP 6 - A
ctivating and deactivating
additional functions........................................................19
Troubleshooting................................................................................ 25
Limited warranty............................................................................... 27
Technical specifications..................................................................28
FRANÇAIS...........................................................................................29
ESPAÑOL............................................................................................. 57
OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE.
PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE
ASSEMBLING & USING THE PRODUCT.
FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT
IN SERIOUS INJURY OR DEATH OR DAMAGES TO THE PRODUCT.
THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS
OLDER THAN 24 MONTHS
THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE IF A CHILD IS OUT
OF THE CRIB
WARNING
Adult assembly required.
Keep small parts away from children when assembling.
2
E
WARNINGS N
1. THIS PRODUCT CANNOT REPL ACE 8. Keep monitor AWAY from heat sources
RESPONSIBLE ADULT SUPERVISION. This (such as stoves, radiators, etc.).
product is designed to aid in the monitoring
of your child. When using the monitor, you 9. ALWAYS place both the Nursery Unit
must still provide the supervision necessary and the Parent Unit on a flat surface in
for the continued safety of your child. an upright position and allow for proper
Monitoring of premature babies, or those ventilation . DO NOT place on sofas ,
considered to be at risk, should always cushions, beds, etc. which may block
be carried out under the supervision of ventilation.
a health professional. This monitor is not
intended to be used as a medical monitor. 10. This monitor uses public airwaves to
transmit signals. The Parent Unit may
2. WARNING Strangulation Hazard — pick up signals or inter ference from
Children have STRANGLED in cords. Keep other nursery monitors in your area. Your
adapter cords out of monitor may even be picked up by other
the reach of children households. To protect your privacy, make
(more than 3 feet sure both units are turned OFF when not in
[0. 9 m] a w ay) . use. If you experience interference, change
NEVER use Sensor the channel on both units.
Pad without the
protective cord 11. This product is NOT a toy. DO NOT allow
covering. Check children to play with it.
protective cord
covering before each use. Immediately 12. This product contains small parts. Adult
discontinue use of Sensor Pad if protective assembly required. Exercise care when
covering is damaged unpacking and assembling the product
or broken. and keep small parts away from children.
3. Never use extension cords with AC 13. When using the monitor, the room
adapters. ONLY use the AC adapters temperature should be between 50°F
provided. (10°C) and 104°F (40°C).
4. When an AC Adapter is plugged into
an electrical outlet, DO NOT touch the
exposed end.
BATTERY WARNING
5. ALWAYS be sure that both the transmitter 14. Use O N LY A A A R EC HARG E AB LE
and receiver are working properly and are batteries for the Parent Unit. DO NOT
within range of each other. Test monitor mix old and new batteries. DO NOT
before first use, periodically and when mix alkaline, standard or rechargeable
changing location of the Nursery Unit. batteries. Insert batteries with correct
polarity. DO NOT short-circuit supply
6. ALWAYS be sure to immediately check terminals. ONLY use the recommended
on baby whenever an alarm sounds. batteries or equivalent (volts and size)
and the correct adapter. Remove batteries
7. DO NOT use monitor near water (such when product is stored for long periods
as bath tub, sink, etc.). of time or when batteries are exhausted.
Dispose exhausted batteries properly. DO
NOT recharge non-rechargeable batteries.
CAUTION Rechargeable batteries are ONLY to be
RISK OF ELECTRIC SHOCK
charged under adult supervision. Keep all
DO NOT OPEN batteries away from children.
DO NOT EXPOSE TO RAIN OR MOISTURE
3
15. IMPORTANT SAFETY INSTRUCTIONS 15.10 Accessories - Only use attachments/
accessories specified by the manufacturer.
15.1 Read these instructions - All the safety DO NOT place this product on an unstable
instructions should be read before the cart, stand, tripod, bracket or table. The
product is operated. product may fall, causing serious injury
to a child or adult and serious damage to
15.2 Keep these instructions. The safety the product. Use ONLY with a cart, stand,
and operating instructions should be tripod, bracket or table recommended by
retained for future reference. the manufacturer or sold with the product.
Any mounting of the product should follow
15.3 Heed all warnings – All warnings on the the manufacturer’s instructions.
product and in the operating instructions
should be adhered to. 15.11 Unplug this appliance during lightning
storms or when not used for long periods
15.4 Follow all instructions – All operating of time.
and use instructions should be followed.
15.12 Ser vicing - DO NOT attempt to
15.5 Water and moisture - DO NOT use service this product yourself as opening
this apparatus near water. For example, or removing covers (except battery doors)
near a bath tub, wash bowl, kitchen sink, may expose you to dangerous voltage or
laundry tub, in a wet environment or near other hazards.
a swimming pool and the like. Care should
be taken so that objects DO NOT fall onto 15.13 R e p l a c e m e n t p a r t s - W h e n
units and that liquids are not spilled into replacement parts are required, be sure
either unit or Sensor Pad through its the replacement parts specified by the
openings. manufacturer have the same characteristic
a s th e o r i g i n a l p a r t . U n a u th o r ize d
15.6 Cleaning - Disconnect all units before substitution may result in fire, electric
cleaning. DO NOT immerse in water any shock or other hazards.
part of the Nursery Unit and the Parent
Unit. Clean only with dry cloth. 15.14 U s a g e - This b a by m o nito r is
intended as an aid. It is NOT a substitute for
15.7 Ventilation - DO NOT block any responsible and proper adult supervision
ventilation openings. Allow for proper and should not be used as such. Use this
ventilation when units are in use. DO NOT appliance ONLY for its intended use as
cover the Nursery Unit or the Parent Unit described in this manual.
with any object such as a blanket. DO NOT
place it in a drawer or in any location which 15.15 Powe r S o u rce s - O p e rate th is
would muffle the sound or interfere with product only from the type of power
the normal flow of air. source indicated on the type plate of the
adaptor. If you are unsure of the type of
15.8 Heat sources - DO NOT install near power supply to your home, consult your
any heat sources such as radiators, heat dealer or local power company.
registers, stoves, TVs or other apparatus
(including amplifiers) that produce heat. 15.16 Overloading - DO NOT overload
Heat can damage the case or electrical wall outlets, extension cords or integral
parts. convenience receptacles as this can result
in a risk of fire or electric shock.
15.9 Power cord protection - Protect the
Sensor Pad cord and the Adapter’s power 15.17 Object and Liquid Entry - NEVER
cord from being walked on or pinched by push objects of any kind into this product
furniture or other items – Power supply through casing slots as they may touch
cords should be routed so that they are not dangerous voltage points or short out
likely to be walked on or pinched by items parts that could result in a risk of fire or
upon or against them, paying particular electric shock. NEVER spill liquid of any
attention to cords and plugs, convenience kind on the product.
receptacle, and the point where they exit
from the product.
4
15.18 Antenna - The antenna used for this Be sure the Sensor Pad is on a flat, firm
transmitter must be installed to provide surface with the printed side facing up. E
a separation distance of at least 7.9” The sensitivity level may also need to be
(20 cm) from all persons and must not be adjusted. Refer to Step 5.1. Always be sure N
collocated or operating in conjunction with to immediately check on baby whenever
any other antenna or transmitter. an alarm sounds.
15.19 Power Lines - An outside antenna 15.23 Sensor Pad - Your Sensor Pad can
system should NOT be located in the be used in any crib that is stationary. If
vicinity of overhead power lines or other the crib has a spring or slat base, place a
electric light or power circuit, or where it hard board between the crib base and the
can fall into such power lines or circuits as Sensor Pad measuring at least 13” x 13”
contact with them may be fatal. (33 x 33 cm) and 1/4 inch (6 mm) thick.
Only use your Angelcare ® monitor in a
15.20 WARNING Strangulation Hazard — stationary sleeping environment such as
Children have STRANGLED in cords. Keep a crib where the Sensor Pad can rest on
adapter cords out of a completely flat, firm surface.
the reach of children
(more than 3 feet
[ 0 . 9 m] away).
NEVER use Sensor
Pad without the
protective cord
covering. Check
protective cord
covering before each use. Immediately
discontinue use of Sensor Pad if protective
covering is damaged or broken.
5
16. IMPORTANT SAFETY INSTRUCTIONS
RELATED TO USE OF BATTERIES
16.1 Use O N LY the t ype and size of 16.9 DO NOT attempt to recharge batteries
batteries specified in the owner’s manual. provided with or identified for use with
There is a risk of explosion if batteries are this product that are not intended to be
replaced with an incorrect type. charged. The batteries may leak corrosive
electrolyte or explode.
16.2 U s e O N LY A A A r e c h a r g e a b l e
batteries and/or the AC Adapters provided 16.10 DO NOT attempt to rejuvenate the
for the Parent Unit. You must use only batteries provided with or identified for
rechargeable batteries in the Parent Unit. use with this product by heating them.
DO NOT use alkaline batteries or you will Sudden release of battery electrolyte may
severely damage the unit. occur, causing burns or irritation to eyes
or skin.
16.3 Charge the batteries for 10 hours prior
to first use. Be sure to have the monitor in 16.11 If and when necessary, the batteries
the OFF position during this period. ONLY must be replaced with identical new ones
use the AC Adapters included with your or equivalent (volts and size). If a battery
monitor. to be replaced is connected with other
batteries in series, replace the other
16.4 DO NOT use these adapters with any batteries at the same time as well. DO
other equipments. NOT mix old and new batteries.
16.5 When unplugging the AC Adapter 16.12 Reverse polarity installation of the
from the Nurser y Unit, be sure it is batteries in the end product must be
switched to the OFF position. If it isn’t, the avoided. Reverse insertion of batteries
unit will revert to battery mode if batteries can cause charging, and that may result
are installed. in leakage or explosion.
16.6 DO NOT use rechargeable batteries 16.13 Remove batteries from this product
in the Nursery Unit. Use alkaline batteries if you store the product over 30 days
ONLY. because the batteries could leak and
damage the product.
16.7 DO NOT dispose batteries in fire. They
may explode. Check with local regulations 16.14 Discard ‘dead’ batteries as soon as
for possible special disposal instructions. possible since ‘dead’ batteries are more
likely to leak in a product. If a battery has
16.8 Exercise care in handling batteries leaked or vented, it should be replaced
in order not to short out the batteries immediately using protective gloves.
with conducting materials such as rings,
bracelets and keys. Overcharging, short 16.15 DO NOT store this product, or the
circuiting, reverse charging, mutilation, or batteries provided with or identified for
incineration of batteries must be avoided use with this product, in high-temperature
to prevent one or more of the following areas.
occurrences: release of toxic materials,
release of hydrogen and/or oxygen gas
and rise in surface temperature.
6
WARNING E
(North America Only) N
17.1 Modifications not authorized by the 17.4 This device complies with the part 15
manufacturer may void users authority to of the FCC Rules and the Industry Canada
operate this device. licence - exempt RSS standards(s). Operation
is subject to the following two conditions:
17.2 NOTE: This equipment has been tested
and found to comply with part 15 of the (1) This device may not cause harmful
FCC Rules and the Industry Canada licence- interference, and
exempt RSS standard(s). These limits are
designed to provide reasonable protection (2) This device must accept any interference
against harmful interference in a residential received, including interference that may
installation. This equipment generates, uses cause undesired operation.
and can radiate radio frequency energy
and, if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
Model AC1100-A
INCLUDED:
4 3 2 1
6 5
3X
2X
IMPORTANT
Keep
at least
6 3 ft (0.9 m)
5
4 3 2 1
8 Sensor Pad
STEP 1 - CHARGING THE PARENT UNIT (10 HOURS)
E
IMPORTANT
N
1 2
Never use regular
alkaline batteries
in the Parent Unit;
they may explode.
NOTE:
To optimize your battery performance
please refer to Battery Guidelines in the
Trouble Shooting section.
PARENT UNIT:
A) LCD Touchscreen
F B) POWER ON/OFF
A
C) Microphone
B D) Speaker
G
E) Charging Cradle
H
F) Belt Clip
G) Speaker
Volume Buttons
C
H) Talk Back Button
D I
I) Battery Door
J) AC Adapter Outlet
(not shown)
E J
9
STEP 2 - INSTALLING THE SENSOR PAD
4 3 2 1 Cord covers 1, 2, 3, 4:
6 5
Position on floor
Cord cover 4:
Contains double sided
tape to securely install
beneath crib leg
Cord cover 5:
Position vertically
between mattress
Sensor Pad with pre-installed cord covers support and floor
Cord cover 6:
Place under
the mattress
WARNING
STRANGULATION HAZARD.
Children have STRANGLED in cords.
• Keep adapter cords out of the reach of children
(more than 3 feet [0.9 m] away).
• Because of the serious strangulation risk to infants
and toddlers, parents and caregivers should never
place the Nursery Unit within 3 feet (0.9 meter) of a
crib.
• NEVER use Sensor Pad without the cord covers.
Check cord covers before each use to ensure it is
securely placed under the leg of the crib. Discontinue
use of Sensor Pad if any cord covers are damaged or
broken.
• NEVER use extension cords with AC adapters. ONLY
use the AC adapters provided. This product is not a
toy. Never allow children to play with it.
IMPORTANT
Keep
at least
6 3 ft (0.9 m)
5
4 3 2 1
10
2.2 - SELECT THE CRIB LEG YOU WILL BE USING TO SECURE THE CORD COVERS
E
N
RECOMMENDED
1) Use the crib leg by the wall closest to
the Nursery Unit (Fig. 1). In cases where
6
the Nursery Unit is across the room, use
the leg closest to the Nursery Unit to
5 position the covered wire (Fig. 2). It is
4 always preferable that the covered cord
3 run along a wall.
2
Fig 1 1
OR
5
4
3
2
1
Fig 2
11
6
3''
WARNING
STRANGULATION HAZARD • The Sensor Pad is not designed for use
• Remove all slack from Sensor Pad Cord. with adults, children or infants older
than 24 months.
• When lowering the mattress support
as your child grows, slide the vertical • Discontinue used of the Sensor Pad
Cord Cover (5) upward so it remains when child is older than 24 months.
approximately in the center between Remove Sensor Pad from crib and store
the mattress support and the floor. Slide for future use.
the Sensor Pad Cord through the Floor • BEFORE FIRST TIME USE: To test
Cover to eliminate any additional slack. that the unit is ready for use, refer to
instruction manual on how to test that
the installation has been done
12
STEP 3 - SETTING UP THE NURSERY UNIT
E
N
1) Remove the battery door and insert
1 3 AAA Alkaline Batteries (not included).
2) Place the Nursery Unit at a minimum
of 3 ft (0.9 m) away from the crib.
3) Connect the AC Adapter to the Nursery
Unit and into an electrical outlet.
4) Direct the angle of the camera toward
the crib using the rotating dial.
2
NOTE:
The batteries maintain power
supply in case of power outage.
IMPORTANT
Keep at least
3 ft (0.9 m)
6 3
5
4 3 2 1
4
NURSERY UNIT:
A) Night Light
B) Main Button
A C) POWER ON/OFF
(Left ‘Wing’)
E) Video Camera
B
F) 4 Infrared LEDs
C D (Night Vision Camera)
J H) Microphone
G I) Speaker
K
J) Sensor Pad Outlet
H L
K) AC Adapter Outlet
L) Roating Dial
for Camera Angle
M N
M) Battery Door
(not shown)
2
1) Press the Parent Unit ON/OFF button
for 2 seconds until blue screen appears.
1 2) The Parent Unit will display
3
Video mode screen.
3) Press the Menu icon to access
main menu.
4) The Parent Unit will display
Menu mode.
4
5 5) Push and hold the Nursery Unit left
‘wing’ button for 2 seconds.
OK
1/3 Full
Vibration only
2/3 Full
Full
14
STEP 5 - TESTING AND GETTING TO KNOW YOUR MONITOR
E
The Angelcare® monitor can be used with the pre-program factory settings or you can N
also customise your settings to your preference.
ON OFF
OK
MOTION ALARM
• Alarm activates when no movement is detected by Sensor Pad for 20 seconds.
• Both the Parent Unit and Nursery Unit speakers will emit loud warning sound.
• Movement Alarm icon will show on the LCD screen.
15
TO STOP THE ALARM
NOTE:
If you are receiving false alarms,
adjust the sensitivity level.
4) Press OK icon to confirm.
Allows you to hear a TIC sound when Sensor Pad function is activated.
2
1 1) Press Menu icon to access
the main menu.
2) Press TIC icon to activate or deactivate
the tic function.
ON OFF
OK
IMPORTANT
• The Sensor Pad is not designed for use with adults, children or infants older
than 24 months.
• Once you are finished using the Sensor Pad, please remove it from the baby’s
crib and store it away.
16
5.2 - SOUND
1) Press Menu icon to access E
TO ACTIVATE SOUND: main menu. N
2) Press sound icon to activate
1 2 or deactivate sound.
ON OFF
OK
3) Press OK icon to confirm.
TO TEST SOUND:
5.3 - BATTERIES
Leave the Parent Unit in the Charging Cradle 1/3 full 2/3 full full
17
YOU ARE NOW READY
TO USE YOUR MONITOR
The Angelcare® monitor can be used with the pre-program factory settings
or you can also customise your settings to your preference.
DEFAULT SETTINGS
Sound Mode: ON
Speaker Volume: Level 3 (of 6)
Motion Mode: ON
Sensor Pad Sensitivity: Level 3 (of 5)
TIC: ON
VOX Mode: ON
VOX Level: Level 2 (of 4)
Timer: OFF
Video Camera: ON
IMPORTANT
• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.
18
STEP 6 - ACTIVATING AND DEACTIVATING ADDITIONAL FUNCTIONS
E
N
All changes and IMPORTANT
adjustments made When in the Menu or Sub-menu
in the main menu and modes, sound transmission between
sub-menus will not be
activated unless you Parent and Nursery Units will be
confirm them by temporarily deactivated. ONLY the
pressing the OK icon. Movement Alarm will remain active
OK (if function is activated).
Allows you to determine the sound level needed to trigger sound transmission
to the Parent Unit.
1 3
1) Press Menu icon to access
2 OFF
the main menu.
19
6.2 - ALARM
Allows you to select your preferred Alarm mode for the Parent Unit.
IMPORTANT
When in Setting mode no sound or alarms will transmit to the Parent Unit, except
the Movement Alarm (if this function was already activated).
6.3 - HOLD
IMPORTANT
When your monitor is on HOLD, the motion-detection feature and Movement Alarm
are disabled.
20
6.4 - THERMOMETER
E
TO CHANGE THE MEASUREMENT UNIT: N
1 2 3 o
30 C
1) Press the Menu icon to access
+
main menu.
o
15 C 2) Press the Temperature icon to access
- sub-menu.
o
C ON
OK ºC
OK
3) Press the ˚C ˚F icon to change from
ºF
Celsius to Fahrenheit.
4) Press OK to confirm.
o o
C F
ºC Celsius ºC Fahrenheit
ºF ºF
o
sub-menu.
15 C
TEMPERATURE ALARM
21
6.5 - VIDEO
1 4
1) Press the Menu icon to access
2 main menu.
2) Press the Video icon to activate
3 or deactivate the video function.
OFF 3) Press OK to confirm.
OK
4) Press the Menu icon to return
to main menu.
ON OFF
MANUAL SETTING:
To trigger manually the screen saver mode push the Parent Unit Power button.
Do not push it for more than 2 seconds since this will shut down the Parent Unit.
OR OR
Push the ON/OFF
Press Talk Back
(but do not hold down for more
button
than 2 seconds or unit will shut
OFF)
22
6.7 - INFRARED NIGHT VISION
E
Allows you to capture image when lighting is unsufficient. N
6.9 - PAGER
23
6.10 - ZOOM MODE
6.11 - MUTE
TO PUT ON MUTE:
Press the (-) button and hold
for 2 seconds to mute sound.
TO UNMUTE: NOTE:
Press the (-) button again and hold On the Parent Unit,
for 2 seconds to unmute sound. the Mute icon will blink.
ON OFF
6.13 - TIMER
24
TROUBLESHOOTING
E
TAKING CARE OF YOUR RECHARGEABLE BATTERIES N
• Ensure that you fully charge your batteries for 10 hours before their first use.
• To maintain maximum battery life it is recommended that you fully discharge your
batteries periodically. Battery performance can be diminished by leaving the batteries
constantly charging on the charging cradle. If your Parent Unit is no in use, please turn
it OFF.
• Inadequate battery power can impair the performance of your monitor. If you are
not happy with the performance of your Parent Unit/Monitor, please replace the
rechargeable batteries (3 x NIMH Rechargeable batteries).
• It is advisable to change the batteries every 6 months.
FALSE ALARMS
WEAK RECEPTION
25
STATIC, DISTORTION, INTERFERENCES
(FROM OTHER MONITORS, WIRELESS PHONES, WALKIE-TALKIES, ETC...)
• Turn the Parent Unit back ON by pushing and holding the power button (left ‘wing’)
for 2 seconds.
• Replace the batteries or recharge Parent Unit.
26
LIMITED WARRANTY
Angelcare® warrants to the original owner of this product that Angelcare® video, movement E
and sound monitor (model AC1100-A) is free from any material and workmanship defects, N
for a period of one (1) year from the date of the original purchase. If this monitoring system
fails to function properly when used as directed under normal conditions within the one
year period, Angelcare® will either repair or replace the product, at our discretion, free of
charge. Please contact your distributor.
The product must be accompanied by a proof of purchase, either a bill of sale or other
proof that the monitoring system is within the warranty period. Angelcare® will bear the
cost of repairing or replacing the product and shipping it back to you.
This warranty does not apply to a product which has been damaged as a result of
improper maintenance, an accident, improper voltage supply or any other form of
misuse. The warranty is also void if the owner repairs or modifies the product in any
way. Angelcare® is not liable for any incidental or consequential damages with regard
to this product. The warranty also excludes any liability other than what is stated above.
No other warranty is given.
This warranty does not cover products and accessories which are not Angelcare-branded,
or any problems that result from usage that is not in accordance with product instructions,
failure to follow the product instructions, or problems caused by using accessories, parts or
components not supplied by Angelcare.
LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING FROM
THE USE OF THIS PRODUCT.
IMPORTANT!
This Angelcare® monitor is a personal care product. Please do not return this product
to the store. If you have questions or need help, please call your distributor before
returning this product.
27
TECHNICAL SPECIFICATIONS They may only be replaced by
3 AAA NIMH rechargeable batteries.
Range: Batteries:
Open field (Open area without
• DO NOT mix old and new batteries.
obstructions): up to 655 feet (200 meters).
• DO NOT mix alkaline standard
Number of Channels: (carbon-zinc), or rechargeable
USA/Canada: 19 channels. (NI-CD, NIMH, etc) batteries.
Europe: 64 Channels.
Transmission:
Power Supply:
Data transmission between the Parent
3 AAA alkaline batteries (not included) or
Unit and Nursery Unit is made on the
7.5V DC Adapter for Nursery Unit.
2.4GHz frequency.
3 AAA rechargeable batteries and 7.5V DC
Hereby, Angelcare Monitors Inc, declares
adapter for Charging Base for the Parent
this baby monitor is in compliance with the
Unit.
essential requirements and other relevant
Caution: To reduce the risk of electric provisions of Directive 1999/5/EC.
shock, do not expose this product to rain
The EU declaration of conformity can be
or moisture.
obtained through your local distributor.
Danger of explosion if batteries are Please refer to address in the manual.
incorrectly replaced. The included Batteries
are 3 AAA NIMH rechargeable batteries,
manufactured by GPI INTERNATIONAL
LIMITED (GN60AAAHC, 1.2V 600mAh) or
by HIGHPOWER TECHNOLOGY CO., LTD
(HFR-44AAAJ600, 1.2V 600mAh).
ErP COMPLIANCE
GERMANY
Use only Angelcare® Brand power supply-model number T07505F002
AUSTRALIA
Use only Angelcare® brand power supply-model number T07505S002
NORTH AMERICA
Use only Angelcare® brand power supply-model number T07505U002
28
www.angelcarebaby.com
IM1100NA-040815