Professional Documents
Culture Documents
Installation Instructions Rightsightt Photoswitch Photoelectric Sensors
Installation Instructions Rightsightt Photoswitch Photoelectric Sensors
Transmitted LED Visible Red 660 nm Visible Red 660 nm Infrared 880 nm
Sensitivity Adjustment no no yes no yes no
Housing/Lens Material Specially formulated polymer/Acrylic
Connection Type Connection Type
Mechanical
Operating Environment NEMA 3R, 4X, 6P, IP67; 8270 kPa (1200 psi) washdown
Vibration/Shock 5g, 10--55 Hz, 1 mm amplitude, meets or exceeds IEC 947--5--2/30g, 1 ms pulse duration, meets or exceeds IEC 947--5--2
Relative Humidity 95%
Certifications UL, CSA, CE for all applicable directives
Catalog Number
42EF- P2MNB- a — 42EF- D1MNAK- a 42EF- S1MNA- a 42EF- B1MNBC- a 42EF- B1MNBE- a 42EF- G1MNA- a 42EF- R9MNB- a 42EF- R9MNBV- a
Complementary LO & DO NPN
DC Sensors
Complementary LO & DO PNP 42EF- P2MPB- a — 42EF- D1MPAK- a 42EF- S1MPA- a 42EF- B1MPBC- a 42EF- B1MPBE- a 42EF- G1MPA- a 42EF- R9MPB- a 42EF- R9MPBV- a
DO NPN & PNP 42EF- P2KBB- a 42EF- U2KBB- a 42EF- D1KBAK- a 42EF- S1KBA- a 42EF- B1KBBC- a 42EF- B1KBBE- a 42EF- G1KBA- a 42EF- R9KBB- a 42EF- R9KBBV- a
LO NPN & PNP 42EF- P2JBB- a 42EF- U2JBB- a 42EF- D1JBAK- a 42EF- S1JBA- a 42EF- B1JBBC- a 42EF- B1JBBE- a 42EF- G1JBA- a 42EF- R9JBB- a 42EF- R9JBBV- a
Voltage/Current/Power Consumption 10.8 to 30V DC @ 35 mA maximum (1 W maximum)
Sensor Protection Input reverse polarity, over voltage, false pulse protected, output short--circuit (SCP) to 100 mA, overload
DC Sensors
MOSFET, Light operate output 42EF- P2RFB- b 42EF- U2RFB- b 42EF- D1RFAK- b 42EF- S1RFA- b 42EF- B1RCFC- b 42EF- B1RFBE- b 42EF- G1RFA- b 42EF- R9RFB- b 42EF- R9RFBV- b
Voltage/Current/Power Consumption 21.6 to 264V AC/DC @ 25 mA maximum (1 VA maximum) 21.6 to 132V AC/DC for 42EF--xxxFx--a models
Sensor Protection Input reverse polarity, over voltage, false pulse protected, output short--circuit (SCP) to 100 mA, overload
Output Type Light/dark operate (N.O./N.C.) MOSFET output
Output Rating 264V AC/DC (132V AC/DC for 42EF--xxxFx--a models) @ 100 mA maximum (SCP protected)
Output Leakage Current 0.4 mA maximum
Response Time 8.3 ms typical, 16 ms for transmitted beam models
Provide NPN output when wired as DC circuit. a = (--A2) 2 m PVC, 300V cable, (--F4) 4--pin DC micro QD on six-inch pigtail
Provide PNP output when wired as DC circuit. b = (--A2) 2 m PVC, 300V cable, (--G4) 4--pin AC micro QD on six-inch pigtail
Contact factory for availability of 8 m range receivers.
Transmitted beam source models: 42EF--E1EZB--a (DC) and 42EF--E1QZB--b (AC/DC)
1
Typical Response Curves
Polarized Retroreflective Standard Retroreflective Diffuse Sharp Cutoff Diffuse Transmitted Beam
6 100 100 100 100
5
Operating Margin
Operating Margin
Operating Margin
Operating Margin
Operating Margin
4 20 m
10 10 10 10
3
2 4m
1 1 1 1 1
0.01 0.1 1 10 0.1 1 10 0.1 1 10 100 2.54 25.4 254 0.1 1 10 100
(0.03) (0.328) (3.28) (32.8) (0.328) (3.28) (32.8) (0.04) (0.4) (3.9) (39) (0.1) (1.0) (10) (0.328) (3.28) (32.8) (328)
Distance to 76 mm Reflector, 92- 39 [m (ft)] Distance [m (ft)] Distance to White Target [cm (in.)] Distance to White Target [mm (in.)] Distance to White Target [m (ft)]
Polarized Retroreflective Beam Pattern Standard Retroreflective Diffuse Beam Pattern Transmitted Beam—4 m Beam Pattern Transmitted Beam—20 m Beam Pattern
20 150 15 0.2 0.5
100 0.4
0.25
Beam Diameter [mm]
Background Suppression Background Suppression Beam Pattern Background Suppression Sensors Glass Fiber Optic Sensors
1000 4
Retaining
2
Beam Diameter [mm]
100 Clip
0
100 mm Groove in
100 mm
10 50 mm Sensitivity end tip
50 mm -2
Adjustment
-4
1
0 20 40 60 80 100 0 1 2 3 4 5 6
(0.7) (1.5) (2.3) (3.1) (3.9) (3) (7) (10) (13) (16) (20) Target
Distance to White Target [mm (in.)] Distance [mm (in.)]
Note: Due to the detection method, targets traveling horizontal to the sensor’s
optics are detected. Targets traveling vertically may not be accurately detected.
For reliable background suppression, a minimum separation distance of 6 mm
(0.24 in.) is recommended between the target and the backgrounds.
2
Short-Circuit Protection the orange LED wil flash until the source is removed (power must be reset for AC/DC
RightSight photoelectric sensors provide short-circuit protection (SCP) on the output models). The SCP limits are set to 100 mA over the entire voltage range for both DC
leads. This feature is intended to protect the sensor from damage in the event that the and AC/DC models.
output load is shorted to ground. If this condition does occur, the SCP will activate and
Wiring Diagrams
10.8--30V DC Sensors 21.6--264V AC/DC Sensors
Models with Dual NPN and PNP Outputs AC Wiring for 42EF- _ _ _C_ _- _ _ Models
Brown + 1 Brown + Blue 2 Red/White
2 L1 L1
White Load White Load 1 4 3
Black Black Black Load 3 Red
4 Load Load 4 2
Load 2 3
Blue Blue 1
– 3 – Brown
L2
1 Red/Black
L2
DC Micro
Cable Quick-Disconnect Cable Quick-Disconnect
Blue – 2 Red/White
–
Transmitted Beam Source
AC and DC Wiring
Brown L1/+ 1 Red/Black L1/+
Blue 2 Red/White
L2/-- L2/--
Note: All wire colors on quick-disconnect models shown refer to Allen-Bradley cordsets. Cable Quick-Disconnect
3
Sensor Dimensions [mm (in.)]
AC/DC 34.5
(1.36)
DC 34.5
20.5 27 (1.36)
(0.81) (1.06) 20.5 27
10 Sensitivity Adjustment (0.81)
(diffuse and glass (1.06)
(0.40) 10
32.7 fiber optic only) (0.40)
(1.29) 32.7
69 (1.29)
(2.72)
46.7
9.6 49.7 (1.84)
(0.38) 27.5
4 (1.96) 9.6 (1.08)
26.5 Indicators 10
(0.16) (0.38) 4
(1.04) (0.40)
M18 x 1,0 (0.16)
thread
19
19 (0.75) 3.6 (0.145) dia.
(0.75) 3.6 (0.145) dia. clearance for #6--32
clearance for #6--32 M18x1.0 thread
18 mm mounting nut 16.5 screw (2 places)
screw (2 places) (0.65)
16.5 2 m (6.56 ft)
(0.65) cable
Accessories
Straight Bracket #60--2656 Right Angle Bracket #60--2657 Swivel/Tilt Bracket #60--2649 Apertures
10 Adjustment in
each direction Transmitted Beam and Retroreflective
Sensing Modes only)
57.15
(2.25)
28.6
(1.125)