Professional Documents
Culture Documents
REN R08ds0197ej0100 ps2506 1 DST 20201225-2930876
REN R08ds0197ej0100 ps2506 1 DST 20201225-2930876
PS2506-1, PS2506L-1
R08DS0197EJ0100
Rev.1.00
HIGH ISOLATION VOLTAGE AC INPUT, DARLINGTON TRANSISTOR TYPE Dec 25, 2020
DESCRIPTION
The PS2506-1 and PS2506L-1 are optically coupled isolator containing a GaAs light emitting diode and an
NPN silicon darlington connected phototransistor.
The PS2506-1 is in a plastic DIP (Dual In-line Package) and the PS2506L-1 is lead bending type (Gull-wing)
for surface mount.
FEATURES
AC input response
High isolation voltage (BV = 5 000 Vr.m.s.) PIN CONNECTION
High current transfer ratio (CTR = 2 000 % TYP.) (Top View)
High-speed switching (tr , tf = 100 s TYP.)
Ordering number of taping product: PS2506L-1-F3 : 2 000 pcs/reel 4 3 1. Anode,
Pb-Free product Cathode
Safety standards 2. Cathode,
UL approved: UL1577, Double protection Anode
1 2 3. Emitter
4. Collector
APPLICATIONS
Power supply
Telephone/FAX
FA/OA equipment
Programmable logic controller
DIP Type
PS2506-1
4.6±0.35
4 3
6.5±0.5
1 2
7.62
3.2±0.4 4.15±0.4
3.5±0.3
0 to 15° +0.1
0.25 –0.05
1.25±0.15
0.50±0.10
0.25 M
2.54
PS2506L-1
4.6±0.35
4 3
6.5±0.5
1 2
0.25 –0.05
+0.1
0.1 –0.05
+0.1
3.5±0.3
1.25±0.15 0.9±0.25
0.25 M 9.60±0.4
2.54 0.15
PHOTOCOUPLER CONSTRUCTION
Parameter PS2506-1, PS2506L-1
MARKING EXAMPLE
No. 1 pin
Mark R Company Initial
N J 0 31
Week Assembled
Year Assembled (Last 1 Digit)
In-house Code
CTR Rank Code
Made in Japan
Pb-Free J
ORDERING INFORMATION
Part Number Order Number Solder Plating Packing Style Safety Standard Application Part
Specification Approval Number *1
PS2506-1 PS2506-1-A Pb-Free Magazine case 100 pcs Standard products PS2506-1
(UL approved)
PS2506L-1 PS2506L-1-A PS2506L-1
Notes: *1. For the application of the Safety Standard, following part number should be used.
IC1
IF1
VCE
IF2 IC2
IF
Pulse lnput VCC Input
PW = 1 ms ton toff
Duty Cycle = 1/10 td ts
VOUT
90 %
50 Ω RL = 100 Ω
Output
10 %
tr tf
150
100
1.5 mW/°C 2 mW/°C
100
50
50
+25 °C
Forward Current I F (mA)
10
20
5
0 °C 0
–25 °C
1 –55 °C –20
0.5
–40
–60
0.1
–80
0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 –1.5 –1.0 –0.5 0 0.5 1.0 1.5
10 000 100
2 mA
VCE = 2 V 50
Collector Current I C (mA)
5V 1 mA
1000 10 V
24 V 10
40 V 0.5 mA
100 5
0.2 mA
10 1
0.5 IF = 0.1 mA
1
0.2
–50 –25 0 25 50 75 100 0.4 0.6 0.8 1.0 1.2 1.4 1.6
1.0
100
0.8
80
2 mA
0.6
60
0.4
40
1 mA
20 0.2
IF = 0.5 mA
6 000 B
C 2 000
5 000 Sample A
D
B
4 000 1 500 C
D
3 000
1 000
2 000
500
1 000
0 0
0.1 0.5 1 5 10 30 10 50 100 500
Switching Time t (μ s)
tf 1 000
μ
tr
100 500
ts
50
td
100
50
10 tr
5 ts 10
td
2
30 50 100 500 1k 5k 300 500 1k 5k 10 k 50 k 100 k
FREQUENCY RESPONSE
IF = 1 mA,
VCE = 2 V
0
Normalized Gain GV
10
15
RL = 100 Ω
20
Frequency f (kHz)
Taping Direction
PS2506L-1-F3
PS2561DL-1-F3
Direction of feed
1.75±0.1
2.0±0.1
+0.1
4.0±0.1 1.5 –0 4.5 MAX.
7.5±0.1
16.0±0.3
10.3±0.1
8.0±0.1
0.4
2.0±0.5
13.0±0.2
330±2.0
100±1.0
R 1.0
21.0±0.8
17.5±1.0
21.5±1.0
C
B
A
PS2506L Lead Bending Type For Surface Mount 8.2 2.54 1.7 2.2
NOTES ON HANDLING
1. Recommended soldering conditions
(1) Infrared reflow soldering
• Peak reflow temperature 260 C or below (package surface temperature)
• Time of peak reflow temperature 10 seconds or less
• Time of temperature higher than 220C 60 seconds or less
• Time to preheat temperature from 120 to 180C 120 30 s
• Number of reflows Three
• Flux Rosin flux containing small amount of chlorine
(The flux with a maximum chlorine content of
0.2 Wt% is recommended.)
(heating)
Package Surface Temperature T (°C)
to 10 s
260 °C MAX.
220 °C
to 60 s
180 °C
120 °C
120 ± 30 s
(preheating)
Time (s)
(a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead
(b) Please be sure that the temperature of the package would not be heated over 100 C
(4) Cautions
• Flux Cleaning
Avoid cleaning with Freon based or halogen-based (chlorinated etc.) solvents.
• Do not use fixing agents or coatings containing halogen-based substances.
3. Measurement conditions of current transfer ratios (CTR), which differ according to photocoupler
Check the setting values before use, since the forward current conditions at CTR measurement differ
according to product.
When using products other than at the specified forward current, the characteristics curves may differ
from the standard curves due to CTR value variations or the like. Therefore, check the characteristics
under the actual operating conditions and thoroughly take variations or the like into consideration before
use.
USAGE CAUTIONS
1. Protect against static electricity when handling.
2. Avoid storage at a high temperature and high humidity.
3. Avoid cleaning with Freon based or halogen-based (chlorinated etc.) solvents.
4. Do not use fixing agents or coatings containing halogen-based substances.
1000
Total Power Dissipation Psi (mW)
900
800
Input Current Isi (mA)
700
600 Psi: Total Power Dissipation
500
400
300
200 Isi: Input Current
100
0
0 25 50 75 100 125 150 175 200
Package temp Tsi (°C)
V UIOTM = 8000 V
Upr = 1424 V
UIORM = 890 V
t3 tm t4 t
t1 tini t2 ttest
t1,t2 = 1 to 10 sec
t3,t4 = 1 sec
tm(PARTIAL DISCHARGE) = 10 sec
ttest = 12 sec
tini = 60 sec
V Upr = 1669 V
UIORM = 890 V
ttest
t
t3 tm t4
All trademarks and registered trademarks are the property of their respective owners.
Authorized Distributor
Renesas Electronics:
PS2506L-1-A PS2506L-1-F3-A PS2506-1-A