Professional Documents
Culture Documents
LOW type
29 mm
W
H
T
L2
L1
[mm]
Model C(L)KQG32
(L)KQG32 Compact
pact cylinder ty
type C(L)KU32 P
Plate
e cylinder type C(L)KQG50
(Guide pin diameter: Ø 12) (Guide pin diameter: Ø 12) (Guide pin diameter: Ø 13)
Clamping height LOW type HIGH type LOW type HIGH type LOW type HIGH type
Clamping height H 30 100 30 100 24 54
Body thickness T 50 29 66
Body width W 50 70 66
Body length L1 127 (159) 132.5 (160) 147.5 (182.5)
Overall length L2 183 (215) 253 (295) 118.5 (216) 258.5 (286) 204.5 (239.5) 234.5 (269.5)
Weight [g] 900 (1140) 1110 (1350) 740 (950) 910 (1120) 1670 (2190) 1840 (2350)
∗ Values in ( ) for specification with lock
C(L)KQG32/C(L)KU32 Series
09-EU553-A-UK
Pin Clamp Cylinders
C(L )KQG32/C(L )KU32 Series
Possible to mount
on 2 surfaces
CKU32-X2321 CLKU32-X2321
Application Examples
CKU32 (Plate cylinder type) CLKU32 (Plate cylinder type with lock)
Compatible with installing in narrow spaces Unclamp direction locking
For clamping small and lightweight workpiece and Drop prevention for workpiece during emergency stops
material handling, etc.
Body width
29 mm
1
Pin Clamp Cylinder Compact Cylinder Type
C(L)KQG32 Series
Ø 32
How to Order
Clamping height
LOW type C L KQG B 32 075 R A L P3DWASC X2081
Clamping height
HIGH type C L KQG B 32 075 R A H M9BW X2082
Number of auto switches
With lock — 2 pcs.
— Without lock 1 pc.
L With lock Bore size S (Unclamping side)
32 32 mm Auto switch type
Mounting surface position — Without auto switch
(viewed from top) ∗ Refer to the table below for the applicable auto switch model.
Guide pin diameter ∗ Auto switches are shipped together, (but not assembled).
Symbol Mounting surface position ∗ For guide pin diameter, ∗ Refer to the table below for the applicable auto switches.
Port side refer to page 3. ∗ When the total thickness of clamped workpiece is
A over 2 mm, the auto switch may not be adjusted to
Mounting the most sensitive position.
Guide pin shape
surface ∗ Secure the minimum bending radius of the auto switch
Round type lead wire before use (Refer to page 17).
Port side
B R Clamp arm position (clockwise viewed from top)
Mounting
surface Symbol Clamp arm position Symbol Clamp arm position
Diamond type Same as the port side 180° from the port side
Port side
D Port side Port side
C A C
Mounting surface Clamp arm Clamp arm
Mounting 90° from the port side 270° from the port side
surface Port side Port side
D Port side B D
Clamp arm Clamp arm
Small Auto Switches Small auto switches cannot be used under a strong magnetic field.
Indicator light
Yes
— Grommet 12 V 100 V A93V∗1 A93 — — Relay,
2-wire 24 V
No 5 V, 12 V 100 V or less A90V A90 — — — IC circuit PLC
∗1 1 m lead wire is only applicable to the D-A93. ∗: Lead wire length symbols: 0.5 m………— (Example) M9NWV
∗ Solid state auto switches marked with “” are produced upon receipt of order. 1 m………M (Example) M9NWVM
∗ Auto switches and mounting brackets are shipped together, (but not assembled). 3 m……… L (Example) M9NWVL
5 m………Z (Example) M9NWVZ
2
C(L)KQG32 Series
Basic Specifications
Model C(L)KQG32
HIGH type with lock
Action Double acting
Bore size [mm] 32
Cylinder stroke/Clamp stroke [mm] 12.5 (Without workpiece)/10
Fluid Air
Minimum operating pressure CKQ: 0.1 MPa CLKQ: 0.15 MPa∗
Maximum Guide pin Ø 7.5 to Ø 13.0 0.7 MPa
operating
pressure diameter [mm] Ø 13.5 to Ø 20.0 1.0 MPa
Ambient and fluid temperature −10 to 60 °C (No freezing)
Cushion None
Lubrication Non-lube
Piston speed (Clamp speed) 50 to 150 mm/sec
Port size (Cylinder port) Rc1/8
∗ Minimum operating pressure is 0.2 MPa when cylinder part and locking part use the same piping.
Lock Specifications
LOW type
Clamping Force
[N]
Guide pin diameter Operating pressure [MPa]
Model
[mm] 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
Ø 7.5 to Ø 13.0 121 181 241 302 362 422 — — —
C(L)KQG32
Ø 13.5 to Ø 20.0 121 181 241 302 362 422 483 543 603
Note 1) It takes approximately 0.3 seconds for the cylinder to operate to generate clamping force from an unclamping state (when no speed controller is installed).
Design circuit taking into consideration the time before the clamping force is generated.
Note 2) Determine the clamping force according to the strength of the workpiece. It can be damaged if the clamping force is too large.
Note 3) Guide pins and clamp arms are consumable items. Please prepare spare parts in case they are damaged. It is recommended to prepare spare parts for guide
pins and clamp arms, especially for products used in workpieces with Ø 12 or less hole diameters.
Weight
Unit: g
CKQG32 CLKQG32
Model
-X2081 -X2082 -X2081 -X2082
Ø 7.5 to Ø 8.0
Ø 8.5 to Ø 9.0
Ø 9.5 to Ø 10.0
900 1110 1140 1350
Ø 10.5 to Ø 11.0
Ø 11.5 to Ø 12.0
Guide pin diameter [mm] Ø 12.5 to Ø 13.0
Ø 13.5 to Ø 14.0
Ø 14.5 to Ø 15.0 940 1150 1180 1390
Ø 15.5 to Ø 16.0
Ø 17.5 to Ø 18.0
950 1160 1190 1400
Ø 19.5 to Ø 20.0
3
Pin Clamp Cylinder
Compact Cylinder Type C(L)KQG32 Series
Replacement Parts
Guide pin
Seal Kit (For type without lock only)
Clamp arm assembly Kit no. Contents
qPiston seal
Basic internal retaining ring
CQ2B32-PS wRod seal
eTube gasket
(Except the -X2081 series)
∗ Seal kit includes q, w, e. Since the seal kit does not include a grease
pack, order the “Grease Pack” below separately.
∗ CLKQ cannot be disassembled and therefore no seal kit is available.
Grease Pack
Kit no. Contents
GR-S-010 Grease 10 g
Rod seal ∗ Please consult with SMC when replacing the actuating cylinders.
Tube gasket
Shim (Option)
Piston seal Refer to page 16 for details about part numbers and dimensions.
Cylinder port
CKQG32-100RH-X2082
Guide Pin Order No. Clamp Arm Assembly Order No. A: Lock unit
holding bolt
CKQG32X 075 R CKQG32X 08 B
B: Cylinder
Guide pin diameter Applicable hole diameter of workpiece
Cylinder head side holding bolt
∗ Refer to Table 1 (Symbol 2) below. ∗ Refer to Table 1 (Symbol 1) below.
Warning
Guide pin shape Clamp arm assembly When replacing the arm for cylinders with
Round type Diamond type ∗ The clamp arm lock (CLKQG32 series), never loosen A: Lock
includes a basic unit holding bolt shown above (2 places).
R D internal retaining ring. (Cylinders are fixed in place with B: Cylinder
holding bolt (2 places).)
Dimensions
CKQG32 (Clamping height LOW type) ∗ The figures below indicate the CKQGB32-RCL-X2081.
27
(Cylinder stroke)
ØD
0
Ø d −0.05
(Clamp stroke)
12.5
K SR
10
C
8 to 10
26
10.5
Mounting surface position
12 15.5 14.5
30
(9)
Port side
A
77±0.1
Mounting
Q
Q
surface
120° 30±0.05
20
(183)
15
(Guide pin dia.: Ø 9.5 or more) B
67
Mounting
15
surface
30
10.5
2 x Ø 6H7
Depth 10 Port side
4 x M8 x 1.25 C Mounting
Depth 12 surface
48
7.5
2 x Rc1/8 Mounting
surface
D
45 49.5 Port side
A
50
Dimensions
CKQG32 (Clamping height HIGH type) ∗ The figures below indicate the CKQGB32-RCH-X2082.
27
0 ØD
Ø d −0.05
(Cylinder stroke)
(Clamp stroke)
K SR
12.5
C
10
8 to 10
26
10.5
14.5
Mounting surface position
Port side
Q
Q
100
A
(79)
120° 85.5 Mounting
surface
147±0.1
Diamond cut shape
(Guide pin dia.: Ø 9.5 or more)
Port side
B
(253)
Mounting
12
surface
30±0.05
20
Port side
C Mounting
15
surface
67
15
Mounting
30
10.5
surface
2 x Ø 6H7
Depth 10 D
Port side
4 x M8 x 1.25
Depth 12
48
7.5
2 x Rc1/8
Clamp arm position
45 49.5 A Same as the port side
32.5 B 90° from the port side
C 180° from the port side
D 270° from the port side
49.5
D
50
Clamp arm
25±0.1
Port side
C A
Mounting surface 19.8
50 B
52
Hole diameter C D d K SR Model
Q number Hole diameter C D d K SR Model
Q number Hole diameter C D d K SR Model
Q number
of workpiece of workpiece of workpiece
7.5 075 11.5 115 15.5 155
7.6 076 11.6 116 15.6 156
7.7 077 11.7 117 15.7 157
Ø8 6 20 3.5 3.5 — Ø 12 8.5 20 5 5 10.9 Ø 16 11.5 25 6 6.5 14.3
7.8 078 11.8 118 15.8 158
7.9 079 11.9 119 15.9 159
8.0 080 12.0 120 16.0 160
8.5 085 12.5 125 17.5 175
8.6 086 12.6 126 17.6 176
8.7 087 12.7 127 17.7 177
Ø9 6.5 20 4 4 — Ø 13 8.5 20 5 5.5 11.6 Ø 18 13 27 6 7.5 16.4
8.8 088 12.8 128 17.8 178
8.9 089 12.9 129 17.9 179
9.0 090 13.0 130 18.0 180
9.5 095 13.5 135 19.5 195
9.6 096 13.6 136 19.6 196
9.7 097 13.7 137 19.7 197
Ø 10 7.5 20 4 4.5 9.2 Ø 14 10.5 25 6 5.5 12.6 Ø 20 13 27 6 8 17.2
9.8 098 13.8 138 19.8 198
9.9 099 13.9 139 19.9 199
10.0 100 14.0 140 20.0 200
10.5 105 14.5 145
10.6 106 14.6 146
10.7 107 14.7 147
Ø 11 7.5 20 4 4.5 9.8 Ø 15 10.5 25 6 6 13.3
10.8 108 14.8 148
10.9 109 14.9 149
11.0 110 15.0 150
6
C(L)KQG32 Series
Dimensions
CLKQG32 (Clamping height LOW type) ∗ The figures below indicate the CLKQGB32-RCL-X2081.
27
ØD Manually unlocking
0
Ø d −0.05 1) Remove the dustproof cover.
2) Screw the commercially available bolt (M3 x 15 L or more)
K SR into the lock ring shown on the left and raise the lock ring
C toward the head side.
8 to 10
3) The lock ring and piston rod form a right angle, and the
lock is released.
26
10.5
Mounting surface position
12 15.5 14.5
30
(9)
Port side
A
Q
Q
77±0.1
Mounting
120° surface
30±0.05
20
Diamond cut shape
(Guide pin dia.: Ø 9.5 or more) Port side
15
B
67
(215)
Mounting
15
Rc1/8 Unlocking port surface
Unlocks when pressurised 30
2 x Ø 6H7
Port side
C
9
Depth 10 Mounting
surface
32
4 x M8 x 1.25
42.5
LOCK
Depth 12
Mounting
surface
80
Dustproof cover
(Manual unlocking unit) D
Port side
48
7.5
2 x Rc1/8
50
Bolt
D 270° from the port side
25±0.1
Clamp arm D
7
Pin Clamp Cylinder
Compact Cylinder Type C(L)KQG32 Series
Dimensions
CLKQG32 (Clamping height HIGH type) ∗ The figures below indicate the CLKQGB32-RCH-X2082.
27
0
ØD Manually unlocking
Ø d−0.05 1) Remove the dustproof cover.
2) Screw the commercially available bolt (M3 x 15 L or
K C more) into the lock ring shown on the left and raise
8 to 10
26
10.5
the lock is released.
14.5
Mounting surface position
100
(79)
Q
147±0.1
Mounting
Diamond cut shape surface
(Guide pin dia.: Ø 9.5 or more)
12
Port side
30±0.05 B
20
(285)
Mounting
surface
15
Rc1/8 Unlocking port
67
4 x M8 x 1.25 Mounting
32
42.5
Depth 12 surface
LOCK
D
Port side
80
Dustproof cover
(Manual unlocking unit)
48
7.5
50
Lock ring
Clamp arm D
25±0.1
Head side
Port side
C A
Mounting surface 19.8
32.5
52 B
C(L)KU32 Series
Ø 32
How to Order
Clamping height
LOW type C L KU 32 075 R A L P3DWASC X2321
Clamping height
HIGH type C L KU 32 075 R A H M9BWV X2322
With lock Number of auto
— Without lock switches
L With lock
Bore size — 2 pcs.
32 Equiv. Ø 32 piston area 1 pc.
S (Unclamping side)
Guide pin diameter
∗ For guide pin diameter, refer
to Table 1 on the next page. Guide pin shape
Auto switch
Round type Diamond type
— Without auto switch
R D ∗ For applicable auto switches,
refer to the table below.
앬 앬 앬 앪 앪
Solid state
Relay,
Diagnostic indication Grommet Yes 2-wire 24 V
— — A79W — 앬 — 앬 — — — PLC
(2-colour indicator)
∗ Solid state auto switches marked with “앪” are produced upon receipt of order.
∗ The D-A9 and A9V cannot be mounted.
∗ Auto switches and mounting brackets are shipped together, (but not assembled).
9
Pin Clamp Cylinder Plate Cylinder Type
Magnetic Field Resistant Auto Switch/Small Auto Switch Mounting C(L)KU32 Series
Model C(L)KU32
Action Double acting
Bore size [mm] Equivalent to 32
Cylinder stroke/Clamp stroke [mm] 12.5 (Without workpiece)/10
Fluid Air
Minimum operating pressure CKU: 0.1 MPa CLKU: 0.15 MPa∗
Maximum operating pressure 0.7 MPa
Ambient and fluid temperature −10 to 60 °C (No freezing)
Cushion None
Lubrication Non-lube
Piston speed (Clamp speed) 50 to 150 mm/sec
Port size (Cylinder port) Rc1/8
∗ Minimum operating pressure is 0.2 MPa when cylinder part and locking part use the same piping.
HIGH type
Lock Specifications
with lock HIGH type
Locking action Spring locking (Exhaust locking)
Unlocking pressure 0.2 MPa
Locking pressure 0.05 MPa
Locking direction Unclamp direction locking
Port size (Lock release port) Rc1/8
Holding force (Maximum static load) 402 N
Clamping Force
[N]
Operating pressure [MPa]
Model Guide pin diameter [mm]
0.2 0.3 0.4 0.5 0.6 0.7
C(L)KU32 Ø 7.5 to Ø 20.0 130 195 260 325 390 455
Note 1) It takes approximately 0.3 seconds for the cylinder to operate to generate clamping force from an unclamping state (when no speed controller is
installed). Design circuit taking into consideration the time before the clamping force is generated.
Note 2) Determine the clamping force according to the strength of the workpiece. It can be damaged if the clamping force is too large.
Note 3) Guide pins and clamp arms are consumable items. Please prepare spare parts in case they are damaged. It is recommended to prepare spare
parts for guide pins and clamp arms, especially for products used in workpieces with Ø 12 or less hole diameters.
Weight
Unit: g
CKU32 CLKU32
Model
-X2321 -X2322 -X2321 -X2322
Ø 7.5 to Ø 8.0
Ø 8.5 to Ø 9.0
Ø 9.5 to Ø 10.0
740 910 950 1120
Ø 10.5 to Ø 11.0
Ø 11.5 to Ø 12.0
Guide pin diameter [mm] Ø 12.5 to Ø 13.0
Ø 13.5 to Ø 14.0
Ø 14.5 to Ø 15.0 780 950 990 1160
Ø 15.5 to Ø 16.0
Ø 17.5 to Ø 18.0
790 960 1000 1170
Ø 19.5 to Ø 20.0
10
C(L)KU32 Series
Replacement Parts
Guide pin
Grease Pack
Kit no. Contents
Rod seal
GR-S-010 Grease 10 g
∗ Please consult with SMC when replacing the actuating cylinders.
Piston seal
Shim (Option)
Refer to page 16 for details about part numbers and dimensions.
Bumper
CKU32-120RL-X2321
Dimensions
CKU32 (Clamping height LOW type) ∗ Refer to “How to Order” for positional relationship of the mounting surface and port.
∗ The figures below indicate the CKU32-RAL-X2321.
0
ØD
Ø d −0.05
C K
SR
26
(4)
15.5 14.5
8 to 10
30
49±0.1
5
Q
Q
(6.4)
120°
14
45
Diamond cut shape 59±0.05
14
(188.5)
+0.012
2 x Ø 6H7 0 through
59 5.5
18
4 x Ø 6.6 through
87.5
5.5 2 x Rc1/8
68 28
14.5±0.1
Arm
14.5±0.1
27
A B
70
Port
Dimensions
CKU32 (Clamping height HIGH type) ∗ Refer to “How to Order” for positional relationship of the mounting surface and port.
∗ The figures below indicate the CKU32-RAH-X2322.
0
ØD
Ø d−0.05
K
C SR
26
14.5
8 to 10
(4)
Q
Q
100
120°
119±0.1
85.5
(258.5)
14
45
59±0.05
14
+0.012
2 x Ø 6H7 0 through
59 5.5
18
4 x Ø 6.6 through
87.5
68 28 Arm
A B
(29)
Port
14.5±0.1
27
70
Dimensions
CLKU32 (Clamping height LOW type) ∗ Refer to “How to Order” for positional relationship of the mounting surface and port.
∗ The figures below indicate the CLKU32-RAL-X2321.
0
ØD Manually unlocking
Ø d −0.05 1) Remove the dustproof cover.
Diamond cut shape K 2) Screw the commercially available
C SR bolt (M3 x 25 L or more) into the
(Guide pin dia.: Ø 11.5 or more)
lock ring shown on the left and
raise the lock ring toward the
head side.
26
(4)
3) The lock ring and piston rod form
a right angle, and the lock is
15.5 14.5
8 to 10
released.
30
49±0.1
5
Q
Q
(6.4)
14
120°
45
59±0.05
14
+0.012
2 x Ø 6H7 0 through
(216)
17.5
4 x Ø 6.6 through 59
50.5
Rc1/8
57.5
Unlocking port
Dustproof cover
2 x Rc1/8
42
15.5
68 5.5
Bolt Clamp arm position
Lock ring A Same as the port side
14.5±0.1
Head side
A B
14.5±0.1
27
70 Port
Dimensions
CLKU32 (Clamping height HIGH type) ∗ Refer to “How to Order” for positional relationship of the mounting surface and port.
∗ The figures below indicate the CLKU32-RAH-X2322.
0
ØD
Ø d −0.05
K
C SR
26
14.5
8 to 10
(4)
Q
100
120°
119±0.1
85.5
Diamond cut shape
(Guide pin dia.: Ø 9.5 or more)
(6.4)
5
14
(286)
Manually unlocking
45
59±0.05
14
4 x Ø 6.6 through
lock ring shown on the left and
59
raise the lock ring toward the
50.5
Bolt
7
A B
Head side
14.5±0.1
27
Port
30 + Shim
thickness
gh
throu
ø22
Shim dimensions
16
C(L)KQG32 Series
Auto Switch Mounting 1
Auto Switch Mounting Height
Applicable cylinder: C(L)KQG32-X2081
C(L)KQG32-X2082
For D-P3DWA
D-P3DWA
≈ 26
≈ 32.5
D-P4DW
≈ 17
20 or more
≈ 41.5
D-M9
Note) Allow 20 mm or more space at the cylinder
D-M9W head side to secure the minimum bending
D-A9 SMC D-M9B
radius of the auto switch lead wire.
SMC D-M9B
For D-P4DW
D-M9V
D-M9WV
D-A9V
≈ 28
35 or more
Auto switch
mounting surfaces
qInsert the auto switch into the qFix the auto switch and the auto
mating groove of the cylinder switch mounting bracket temporarily
tube. with the hexagon socket head cap
wCheck the detecting position of screws (M3 x 14 L).
Auto switch
the auto switch and fix the auto wInsert the hexagon socket head cap
mounting screw
switch firmly with the hexagon screws (M2.5 x 5 L) into the spring
washers (for M2.5), and tighten the
socket head cap screw (attached
auto switch mounting bracket and Auto
to the auto switch). auto switch mounting nut temporarily.
Note) The tightening torque for the switch
eInsert the temporarily fixed auto
hexagon socket head cap screw is
switch mounting nut into the mating
0.2 to 0.3 N·m.
groove of the cylinder tube.
Hexagon socket head cap screw rCheck the detecting position of the
(attached to the auto switch) auto switch and fix the auto switch
firmly with the hexagon socket head
¡When tightening the auto
cap screw (M2.5 x 5 L, M3 x 14 L).
Note 1) The tightening torque for the hexagon switch mounting screw, use a
Mounting of socket head cap screw (M3 x 14 L) is watchmakers’ screwdriver
auto switch 0.5 to 0.6 N⋅m. with a handle 5 to 6 mm in
Note 2) The tightening torque for the hexagon diameter.
socket head cap screw (M2.5 x 5 L)
is 0.25 to 0.35 N⋅m.
Auto switch
Tightening Torque for Auto
mounting bracket Hexagon socket Switch Mounting Screw [N·m]
Hexagon socket head cap screw Auto switch model Tightening torque
(M2.5 x 0.45 x 5 L
head cap screw
Spring washer
D-A9(V) 0.10 to 0.20
(M3 x 0.5 x 14 L, (Excluding D-A93)
with spring washer) (For M2.5)
D-M9(V)
D-M9W(V) 0.05 to 0.15
D-M9A(V)
D-A93
Auto switch
mounting nut
18
C(L)KU32 Series
Auto Switch Mounting 2
Auto Switch Mounting Height
Applicable cylinder: C(L)KU32-X2321
C(L)KU32-X2322
D-P3DWA ≈ 44.5
≈ 23.5
D-M9V ≈ 40
D-M9WV
≈ 35
D-A7 ≈ 40
≈ 22
19
Auto Switch Mounting C(L)KQG32 Series
Auto switch
mounting surfaces
With lock
qRemove the screw (M2.5 x 11 L) qRemove the set screw attached to qSlide the square nut into the
attached to the auto switch the auto switch. (The set screw is groove of the rail, and fix the auto
temporarily. not required.) switch on the cylinder with the
wInsert the temporarily removed wFix the auto switch to the auto cross recessed round head screw
screw into the auto switch switch mounting bracket with the (M3 x 6.5 L).
mounting bracket, and fix the round head combination screw Note) The tightening torque for the cross
bracket on the auto switch. (M2.5 x 6 L). recessed round head screw (M3 x
6.5 L) is 0.5 to 0.7 N⋅m.
eSlide the auto switch mounting nut eSlide the square nut into the
into the groove of the rail, and fix groove of the rail, and fix the auto
the auto switch mounting bracket switch mounting bracket on the
on the cylinder with the hexagon cylinder with the cross recessed
socket head cap screw (M3 x 4 L) round head screw (M3 x 6.5 L).
and spring washer (M3). Note) The tightening torque for the round
Note) The tightening torque for the head combination screw (M2.5 x 6
hexagon socket head cap screw L) is 0.1 to 0.2 N⋅m and for the
(M2.5 x 11 L) is 0.2 to 0.3 N·m. cross recessed round head screw
The tightening torque for the (M3 x 6.5 L) is 0.5 to 0.7 N⋅m.
hexagon socket head cap screw
(M3 x 4 L) is 0.5 to 0.7 N·m.
Mounting of
auto switch Hexagon socket
Hexagon socket head cap screw head cap screw
(attached to the auto switch) (M3 x 4 L)
(M2.5 x 11 L)
. Spring washer
@
Auto switch Set screw
(Not required)
M3 x 6.5 L M2.5 x 6 L
Auto switch M3 x 6.5 L
mounting bracket Auto switch
: mounting bracket
Auto switch
Groove
mounting nut Square nut
Square nut of rail
20
SMC Corporation (Europe)
Austria +43 (0)2262622800 www.smc.at office@smc.at Lithuania +370 5 2308118 www.smclt.lt info@smclt.lt
Belgium +32 (0)33551464 www.smcpneumatics.be info@smcpneumatics.be Netherlands +31 (0)205318888 www.smcpneumatics.nl info@smcpneumatics.nl
Bulgaria +359 (0)2807670 www.smc.bg office@smc.bg Norway +47 67129020 www.smc-norge.no post@smc-norge.no
Croatia +385 (0)13707288 www.smc.hr office@smc.hr Poland +48 222119600 www.smc.pl office@smc.pl
Czech Republic +420 541424611 www.smc.cz office@smc.cz Portugal +351 226166570 www.smc.eu postpt@smc.smces.es
Denmark +45 70252900 www.smcdk.com smc@smcdk.com Romania +40 213205111 www.smcromania.ro smcromania@smcromania.ro
Estonia +372 6510370 www.smcpneumatics.ee smc@smcpneumatics.ee Russia +7 8127185445 www.smc-pneumatik.ru info@smc-pneumatik.ru
Finland +358 207513513 www.smc.fi smcfi@smc.fi Slovakia +421 (0)413213212 www.smc.sk office@smc.sk
France +33 (0)164761000 www.smc-france.fr info@smc-france.fr Slovenia +386 (0)73885412 www.smc.si office@smc.si
Germany +49 (0)61034020 www.smc.de info@smc.de Spain +34 902184100 www.smc.eu post@smc.smces.es
Greece +30 210 2717265 www.smchellas.gr sales@smchellas.gr Sweden +46 (0)86031200 www.smc.nu post@smc.nu
Hungary +36 23513000 www.smc.hu office@smc.hu Switzerland +41 (0)523963131 www.smc.ch info@smc.ch
Ireland +353 (0)14039000 www.smcpneumatics.ie sales@smcpneumatics.ie Turkey +90 212 489 0 440 www.smcpnomatik.com.tr info@smcpnomatik.com.tr
Italy +39 0292711 www.smcitalia.it mailbox@smcitalia.it UK +44 (0)845 121 5122 www.smcpneumatics.co.uk sales@smcpneumatics.co.uk
Latvia +371 67817700 www.smclv.lv info@smclv.lv
SMC CORPORATION Akihabara UDX 15F, 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021, JAPAN Phone: 03-5207-8249 FAX: 03-5298-5362
1st printing WS printing WS 00 Printed in Spain Specifications are subject to change without prior notice and any obligation on the part of the manufacturer.