Professional Documents
Culture Documents
AU OPTRONICS CORPORATION
( ) Preliminary Specifications
.tw
( ) Final Specifications
Module 17.3”(17.25”) FHD 16:9 Color TFT-LCD with LED Backlight design
m
Note ( ) LED Backlight with driving circuit design
Customer
d
Date
.co Approved by Date
slc
Checked &
w.y
Contents
1. Handling Precautions ....................................................................................... 4
2. General Description .......................................................................................... 5
2.1 General Specification .........................................................................................................5
2.2 Optical Characteristics .......................................................................................................6
3. Functional Block Diagram .............................................................................. 11
.tw
4. Absolute Maximum Ratings ........................................................................... 12
4.1 Absolute Ratings of TFT LCD Module ..............................................................................12
4.2 Absolute Ratings of Environment .....................................................................................12
5. Electrical Characteristics ............................................................................... 13
5.1 TFT LCD Module..............................................................................................................13
m
5.2 Backlight Unit ...................................................................................................................15
6. Signal Interface Characteristic....................................................................... 16
6.1 Pixel Format Image ..........................................................................................................16
.co
6.2 The Input Data Format .....................................................................................................17
6.3 Integration Interface Requirement....................................................................................18
6.4 Interface Timing................................................................................................................21
7. Panel Reliability Test ...................................................................................... 23
d
7.1 Vibration Test....................................................................................................................23
7.2 Shock Test........................................................................................................................23
slc
7.3 Reliability Test ..................................................................................................................23
8. Mechanical Characteristics ............................................................................ 24
8.1 LCM Outline Dimension ...................................................................................................24
8.2 Screw Hole Depth and Center Position............................................................................26
w.y
Record of Revision
m .tw
d .co
slc
w.y
ww
1. Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
.tw
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
m
7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
.co
tilt the Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure (Notebook PC Bezel, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
d
12) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
slc
(IEC60950 or UL1950), or be applied exemption.
13) Disconnecting power supply before handling LCD modules, it can prevent electric shock, DO
NOT TOUCH the electrode parts, cables, connectors and LED circuit part of TFT module that
a LED light bar build in as a light source of back light unit. It can prevent electrostatic
w.y
breakdown.
ww
2. General Description
B173HW02 V1 is a Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a
driver circuit, and LED backlight system. The screen format is intended to support the FHD 16:9
1920(H) x 1080(V) screen and 262k colors (RGB 6-bits data driver) with LED backlight driving
circuit. All input signals are LVDS interface compatible.
.tw
B173HW02 V1 is designed for a display unit of notebook style personal computer and industrial
machine.
2.1 General Specification
The following items are characteristics summary on the table at 25 ℃ condition:
m
Items Unit Specifications
Screen Diagonal [mm] 17.3W”(17.25)
Active Area [mm] 381.888 X 214.812
Pixels H x V
Pixel Pitch
Pixel Format
Display Mode
White Luminance (ILED=20mA)
d .co
[mm]
2
1920x3(RGB) x1080
0.1989X0.1989
R.G.B. Vertical Stripe
Normally White
300 typ. (5 points average)
[cd/m ]
(Note: ILED is LED current) 255 min. (5 points average)
Luminance Uniformity 1.25 max. (5 points) / 1.35 max. (13 points)
slc
Contrast Ratio 400 typ
Response Time [ms] 8 typ / 16 Max
Nominal Input Voltage VDD [Volt] +3.3 typ.
Power Consumption [Watt] 9.0 max. (Include Logic and Blu power)
w.y
.tw
θR Horizontal (Right) 60 70 ---
θL CR = 10 (Left)
60 70 ---
Viewing Angle degree 4, 9
ψH Vertical (Upper) 45 60 ---
ψL CR = 10 (Lower)
50 60 ---
Luminance Uniformity δ5P 5 Points --- --- 1.25 1, 3, 4
m
Luminance Uniformity δ13P 13 Points --- --- 1.42 2, 3, 4
Contrast Ratio CR 300 400 --- 4, 6
Cross talk %
Response Time
d TRT
Rx
.co
Rising + Falling
---
---
TBD
---
TBD
4
16
TBD
msec
4, 7
4, 8
Red
Ry TBD TBD TBD
Gx
slc
TBD TBD TBD
Green
Color / Gy TBD TBD TBD
Chromaticity
Coodinates Bx CIE 1931 TBD TBD TBD 4
Blue ---
By TBD TBD TBD
w.y
W
W /4 W /4 W /4 W /4
H /4
1 2
.tw
H /4
H 3
H /4
4 5
m
H /4
W /4 W /4
10
1 2 3
H /4
4 5
slc
H /4
H 6 7 8
H /4
w.y
9 10
H /4 11 12 13
10
Note 3: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the
minimum test point luminance
ww
δ
Maximum Brightness of five points
W5 =
Minimum Brightness of five points
δ
Maximum Brightness of thirteen points
W13 =
Minimum Brightness of thirteen points
for 30 minutes in a stable, windless and dark room, and it should be measured in the center of screen.
Photo detector
.tw
Field=2°
m
50 cm
Note 5 :
LCD Panel
.co
Center of the screen
Definition of Average Luminance of White (YL):
d TFT-LCD Module
,
slc
Measure the luminance of gray level 63 at 5 points YL = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5
L (x) is corresponding to the luminance of the point X at Figure in Note (1).
Where
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
.tw
Note 8: Definition of response time:
m
The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to “White”
(falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the 10% and
90% of amplitudes. Refer to figure as below.
100%
"White"
.co"Black"
"White"
Signal(Relative value)
90%
d
slc
10%
0%
Tr Tf
w.y
ww
m .tw
d .co
slc
w.y
ww
m .tw
d .co
slc
w.y
ww
.tw
4.2 Absolute Ratings of Environment
Item Symbol Min Max Unit Conditions
o
Operating Temperature TOP 0 +50 [ C] Note 4
Operation Humidity HOP 5 95 [%RH] Note 4
o
m
Storage Temperature TST -20 +60 [ C] Note 4
Storage Humidity HST 5 95 [%RH] Note 4
Note 1: At Ta (25℃)
.co
Note 2: Permanent damage to the device may occur if exceed maximum values
Note 3: LED specification refer to section 5.2
Note 4: For quality performance, please refer to AUO IIS (Incoming Inspection Standard).
d
Twb=39°C
slc
w.y
ww
5. Electrical Characteristics
5.1 TFT LCD Module
5.1.1 Power Specification
Input power specifications are as follows;
The power specification are measured under 25 ℃ and frame frenquency under 60Hz
.tw
Symble Parameter Min Typ Max Units Note
Logic/LCD Drive [Volt]
VDD 3.0 3.3 3.6
Voltage
PDD VDD Power - 2 [Watt] Note 1
-
IDD IDD Current 600 [mA] Note 1
m
- 350
IRush Inrush Current 2000 [mA]
- - Note 2
Allowable
[mV]
VDDrp Logic/LCD Drive Ripple - - 100
p-p
Voltage
:
.co
Note 1 : Maximum Measurement Condition Black Pattern at 3.3V driving voltage. (Pmax=V3.3 x Iblack)
:
Note 2 Measure Condition
d
slc
w.y
ww
90% 3.3V
10%
0V
0.5ms
.tw
Differential Input High
Vth --- 100
Threshold (Vcm=+1.2V) [mV]
Differential Input Low
Vtl -100 ---
Threshold (Vcm=+1.2V) [mV]
m
Differential Input Common
Vcm 1.125 1.375 [V]
Mode Voltage
Backlight Power ℃
(Ta=25 ), Note 1.
.tw
PLED - - 7 [Watt]
Consumption Vin=12V
m
Note 1: Calculator value for reference PLED = VF (Normal Distribution) * IF (Normal Distribution) / Efficiency
Note 2: The LED life-time define as the estimated time to 50% degradation of initial luminous.
Parameter
VLED
Min
7.0
Typ
12.0
Max
21.0
Units
[Volt]
Remark
High Level
1 1920
.tw
1st Line R GB R GB R GB R GB
m
d .co
1080th Line R GB R GB R GB R GB
slc
w.y
ww
m .tw
Signal Name
d
Description
.co
R5 Red Data 5 (MSB) Red-pixel Data
R4 Red Data 4 Each red pixel's brightness data consists of these 6 bits pixel data.
R3 Red Data 3
slc
R2 Red Data 2
R1 Red Data 1
R0 Red Data 0 (LSB)
Red-pixel Data
G5 Green Data 5 (MSB) Green-pixel Data
G4 Green Data 4 Each green pixel's brightness data consists of these 6 bits pixel data.
w.y
G3 Green Data 3
G2 Green Data 2
G1 Green Data 1
G0 Green Data 0 (LSB)
Green-pixel Data
B5 Blue Data 5 (MSB) Blue-pixel Data
B4 Blue Data 4 Each blue pixel's brightness data consists of these 6 bits pixel data.
B3 Blue Data 3
B2 Blue Data 2
ww
B1 Blue Data 1
B0 Blue Data 0 (LSB)
Blue-pixel Data
RxCLKIN Data Clock The signal is used to strobe the pixel data and DE signals. All pixel data
shall be valid at the falling edge when the DE signal is high.
DE Display Timing This signal is strobed at the falling edge of
RxCLKIN. When the signal is high, the pixel data shall be valid to be
displayed.
VS Vertical Sync The signal is synchronized to RxCLKIN .
HS Horizontal Sync The signal is synchronized to RxCLKIN .
Note: Output signals from any system shall be low or High-impedance state when VDD is off.
.tw
Connector Name / Designation For Signal Connector
m
Mating Housing/Part Number JAE HD1S040HA1 or Compatible
PIN#
1
Signal Name
NC
d
Description
No Connection
.co
LVDS is a differential signal technology for LCD interface and high speed data transfer device.
.tw
29 RxECKIN- -LVDS Even Differential Clock INPUT
30 RxECKIN+ +LVDS Even Differential Clock INPUT
31 VLED_GND LED Ground
32 VLED_GND LED Ground
33 VLED_GND LED Ground
m
34 NC No Connection
35 S_PWMIN System PWM Logic Input level
36 LED_EN LED enable input level
37
38
39
40
NC
VLED
VLED
VLED
d No Connection.co
LED Power Supply
LED Power Supply
LED Power Supply
slc
w.y
ww
Note1: Input signals shall be low or High-impedance state when VDD is off.
m .tw
.co Pin 40 Pin 1
NC
VLED
d
slc
Note1: Input signals shall be low or High-impedance state when VDD is off.
w.y
ww
.tw
Clock frequency 1/ TClock 50 74.9 85 MHz
Period TV 1088 1130 1680
Vertical TLine
Active TVD 1080
Section
Blanking TVB 8 50 -
m
Period TH 990 1050 -
Horizontal
Active THD 960 TClock
Section
Blanking THB 30 90 -
DE
THB THD
TH
ww
DE
TVB
TVD
TV
Power on/off sequence is as follows. Interface signals and LED on/off sequence are also shown in
the chart. Signals from any system shall be Hi-Z state or low level when VDD is off
m .tw
d .co
Wiat for check with system
slc
Power Sequence Timing
Value(Units: ms)
Parameter Min. Max.
T1 0.5 10
w.y
T2 0 50
T3 200 -
T4 200 -
T5 0 50
T6 0 10
ww
T7 500 -
T8 10 -
T9 10 180
T10 10 180
T11 10 -
T12 0.5 10
.tw
Frequency: 10 - 500Hz Random
Sweep: 30 Minutes each Axis (X, Y, Z)
m
Test Spec:
Test method: Non-Operation
Acceleration: 220 G , Half sine wave
Active time: 2 ms
Pulse:
Contact : ±8 KV Note 1
ESD
Air : ±15 KV
ww
Note1: According to EN 61000-4-2 , ESD class B: Some performance degradation allowed. No data lost
. Self-recoverable. No hardware failures.
Remark: MTBF (Excluding the LED): 30,000 hours with a confidence level 90%
tw
8. Mechanical Characteristics
8.1 LCM Outline Dimension
m.
.co
s lcd
w.y
ww
tw
m.
.co
s lcd
w.y
ww
Note: Prevention IC damage, IC positions not allowed any overlap over these areas.
The center of screw hole center location is 3.1 ± 0.2mm from front surface
Screw Torque: Maximum 2.5 kgf-cm
m .tw
d .co
slc
w.y
ww
m .tw
d .co
9.2 Carton Package
slc
w.y
ww
m .tw
d .co
slc
w.y
ww
.tw
2 Header TBD TBD TBD
Header
m
7 Header TBD TBD TBD
8 EISA manufacture code = 3 Character ID TBD TBD TBD
9 EISA manufacture code (Compressed ASCII) TBD TBD TBD
0A
0B
.co
Panel Supplier Reserved – Product Code
Panel Supplier Reserved – Product Code
LCD module Serial No - Preferred but Optional (“0” if
TBD
TBD
TBD
TBD
TBD
TBD
Vendor / Product
.tw
29 Standard timing ID2 (01h if not used) TBD TBD TBD
2A Standard timing ID3 (01h if not used) TBD TBD TBD
2B Standard timing ID3 (01h if not used) TBD TBD TBD
Standard Timing ID
m
2E Standard timing ID5 (01h if not used) TBD TBD TBD
2F Standard timing ID5 (01h if not used) TBD TBD TBD
30 Standard timing ID6 (01h if not used) TBD TBD TBD
31
32
33
34
35
.co
Standard timing ID6 (01h if not used)
Standard timing ID7 (01h if not used)
Standard timing ID7 (01h if not used)
Standard timing ID8 (01h if not used)
Standard timing ID8 (01h if not used)
d TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Pixel Clock/10,000
36 (LSB) TBD TBD TBD
Pixel Clock/10,000
slc
37 (MSB) TBD TBD TBD
Horizontal Active = ???? pixels
38 (lower 8 bits) TBD TBD TBD
Horizontal Blanking (Thbp) = 320 pixels
39 (lower 8 bits) TBD TBD TBD
Horizontal Active/Horizontal blanking (Thbp)
w.y
.tw
47 ==> fix=1A TBD TBD TBD
Pixel Clock/10,000
48 (LSB) TBD TBD TBD
Pixel Clock/10,000
49 (MSB) TBD TBD TBD
Horizontal Active = xxxx pixels
4A (lower 8 bits) TBD TBD TBD
m
Horizontal Blanking (Thbp) = xxxx pixels
4B (lower 8 bits) TBD TBD TBD
Horizontal Active/Horizontal blanking (Thbp)
4C (upper4:4 bits) TBD TBD TBD
4D
4E
4F
.co
Vertical Active = xxxx lines
Vertical Blanking (Tvbp) = xxxx lines (DE Blanking
typ. for DE only panels)
Vertical Active : Vertical Blanking (Tvbp)
(upper4:4 bits)
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
(=Timing Descripter #1)
Timing Descripter #2
.tw
67 Manufacturer P/N TBD TBD TBD
68 Manufacturer P/N TBD TBD TBD
69 Manufacturer P/N TBD TBD TBD
6A Manufacturer P/N TBD TBD TBD
Manufacturer P/N (If <13 char, then terminate with
6B ASCII code 0Ah, set remaining char = 20h) TBD TBD TBD
m
6C Flag TBD TBD TBD
6D Flag TBD TBD TBD
6E Flag TBD TBD TBD
6F
70
71
72
==>fix=00
Flag
Color Management
Panel Structure
.co
Data Type Tag: Manufacturer Specified Data 00
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Timing Descripter #4
d
73 Frame Rate TBD TBD TBD
74 Light Controller Interface and Luminance TBD TBD TBD
slc
75 Outdoor Features TBD TBD TBD
76 Multi-Media Features TBD TBD TBD
77 Multi-Media Features TBD TBD TBD
78 Special Features #1 TBD TBD TBD
w.y
Special Features #2
79 TBD TBD TBD
Special Features #3
7A TBD TBD TBD
(If <13 char, then terminate with ASCII code 0Ah, set
7B remaining char = 20h) TBD TBD TBD
(If <13 char, then terminate with ASCII code 0Ah, set
7C remaining char = 20h) TBD TBD TBD
(If <13 char, then terminate with ASCII code 0Ah, set
ww