Professional Documents
Culture Documents
4875 Quick Start Guide
4875 Quick Start Guide
4875/76
Master
Console
Getting Started
Components
PC
4890 Administration
Program Software
Cat. 4882 Remote Station
Version 1.2
6/16/08 Page 1 of 16
4875/76 Master Console Quick Start
System Diagram
Cat-5
65
75
Cat-5 BUS 1
REMOTE
STATION
BUS 2 65
75
BUS 3
LOGIC BOARD
4875 MASTER CONSOLE
BUS 4 10-POSITION DIPSWITCH 65
75
DATA BUS
FAULT HEARTBEAT
LEDs LED 65
75
POWER SUPPLY
Version 1.2
6/16/08 Page 2 of 16
4875/76 Master Console Quick Start
Set Dipswitches
SIDE
VIEW
Dipswitch Settings: 1111101011
BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM BOTTOM
ON postion ON postion ON postion ON postion ON postion
ON postion OFF postion ON postion
ON postion OFF postion ON postion ON postion
1 2 3 4 5 6 7 8 9 10
SIDE
VIEW Dipswitch: 0000
Version 1.2
6/16/08 Page 3 of 16
4875/76 Master Console Quick Start
1 2 3 4 5 6 7
Version 1.2
6/16/08 Page 4 of 16
4875/76 Master Console Quick Start
Connections
Set the Master Port to ‘75’
P205
1
AUX
P201
J401A
Sub-port #1
J401B
Sub-port #2
J201
J401C
Sub-port #3
65
Sub-port #4
MASTER
A
Used 75 J401D
SW1
Unused
Version 1.2
6/16/08 Page 5 of 16
4875/76 Master Console Quick Start
J2 J1
Cat-5 Cable to J1 on Cat. 4882 Station
Version 1.2
6/16/08 Page 6 of 16
4875/76 Master Console Quick Start
Programming
Install 4890 application as outlined in the 4890 Installation and User’s Guide before
proceeding. After you have installed the application and connected the PC to the Pro-
Alert system:
Connect Power
Supply to
105 to 132V
facility
power supply
Connection
Port
Click OK
Version 1.2
6/16/08 Page 7 of 16
4875/76 Master Console Quick Start
Version 1.2
6/16/08 Page 8 of 16
4875/76 Master Console Quick Start
Version 1.2
6/16/08 Page 9 of 16
4875/76 Master Console Quick Start
.
Enter 1001 as the arch
address for the bus station. Set audio bus to 1
Version 1.2
6/16/08 Page 10 of 16
4875/76 Master Console Quick Start
Operation
Place a Call
Version 1.2
6/16/08 Page 11 of 16
4875/76 Master Console Quick Start
Verify
Call Placed
LED
Illuminates
Answer Call
or
Lift Handset to establish audio connection or Press Enter/Talk to use panel microphone
& panel speaker
Version 1.2
6/16/08 Page 12 of 16
4875/76 Master Console Quick Start
Cancel Call
Version 1.2
6/16/08 Page 13 of 16
4875/76 Master Console Quick Start
.
or
Lift Handset to establish audio connection or Press Enter/Talk to use panel microphone
& panel speaker
Cancel Call
Version 1.2
6/16/08 Page 14 of 16
4875/76 Master Console Quick Start
Troubleshooting
Symptom Possible Cause Remedy
Dipswitch settings on the remote station are incorrect.
4875 display reads:
1001: FAILED Verify that the dipswitch on the remote station is set according to
page 4.
4875 display reads: You entered the Verify that the entered architectural
INVALID after an architectural address address matches the address programmed
attempt to originate a call incorrectly when using 4890 software.
to the remote station. originating the call. See page 10.
Power down the main control, set the port
Master port switch is set
4875 display reads: switch to ‘75,’ then power up the main
to ‘65’.
WAITING FOR control.
DATA 4875 is actively
No action is necessary.
receiving configuration.
Verify that you have properly
Master port is not
programmed the master port. (See page
programmed.
4875 display reads: 9.)
NOT CONFIGURED Verify that you have the dipswitches set
Dipswitches are set
properly on the main control, master
incorrectly.
console, and bus station. (See pages 3-4)
4875 master is not Verify that you have not connected the
4875 display continues to
connected to a sub-port master station to an RJ-45 port on the
read, TESTING
on the master port. audio bus.
Bus station is connected Verify that the bus station is programmed
Call displays at the master
to an audio bus other for audio bus 1 in 4890 programming,
station but there is no
than the one you then verify that the station is connected to
audio.
assigned using 4890. an RJ-45 port on audio bus 1.
Main Control
Green Heartbeat LED*
Condition Indication Action
System operating
Steadily
normally with valid No action is necessary.
flashing
configuration
Rapidly System does not have Upload valid code into the system using the 4890
flashing valid code. application.
Version 1.2
6/16/08 Page 15 of 16
4875/76 Master Console Quick Start
Version 1.2
6/16/08 Page 16 of 16